Wyniki wyszukiwania dla: PLASTIC
-
Influence of thermal effects on mechanical properties of PVDF-coated fabric
PublikacjaThis paper describes the method of laboratory tests necessary for identification of temperature influence on mechanical properties of polyvinylidene fluoride-coated polyester fabric often used for tensile structures. Two nonlinear model descriptions are investigated. The first one is based on the piece-wise linear relations between stress and strain and the second one on the Murnaghan model of solid behavior. This paper is proposed...
-
Mechanical properties of polyvinyl chloride-coated fabric under cyclic tests
PublikacjaThe aim of the present paper is to propose a method of laboratory tests necessary for the identification of mechanical properties of the coated fabric. The material parameters of the coated fabric AF 9032 are specified on the basis of the uniaxial and biaxial tensile tests. For the identification process, the techniques based on the least squares methods are used. Additionally, the uniaxial and biaxial cyclic tests are performed...
-
Mariusz Kaczmarek dr hab. inż.
OsobyReceived M.Sc., Eng. in Electronics in 1995 from Gdansk University of Technology, Ph.D. in Medical Electronics in 2003 and habilitation in Biocybernetics and Biomedical Engineering in 2017. He was an investigator in about 13 projects receiving a number of awards, including four best papers, practical innovations (7 medals and awards) and also the Andronicos G. Kantsios Award and Siemens Award. Main research activities: the issues...
-
Polypropylene structure alterations after 5 years of natural degradation in a waste landfill
PublikacjaUp to 25% of plastic waste in Europe is still disposed of in landfills, despite recycling efforts. The plastic waste in the landfill plot may be exposed both to abiotic and biotic degradation processes, although it is thought that most of the plastic materials tend to be resistant to biodegradation or biodeterioration even after a long time. To verify if polypropylene (PP) can undergo the process of short-term biodegradation and...
-
Offshore surface waters of Antarctica are free of microplastics, as revealed by a circum-Antarctic study
PublikacjaIn 2018, during a circum navigation of Antarctica below 62° S by the sailing boat Katharsis II, the presence of plastics was investigated with surface sampling nets at ten evenly spaced locations (every 36° of longitude). Although fibres that appeared to be plastic (particles up to 2 cm) were found in numbers ranging from 1 particle (0.002 particles per m3) to 171 particles (1.366 particles per m3) per station, a Fourier-transform...
-
The effect of groyne field on trapping macroplastic. Preliminary results from laboratory experiments
PublikacjaMacroplastic, a precursor of microplastic pollution, has become a new scope of research interest. However, the physical processes of macroplastic transport and deposition in rivers are poorly understood, which makes the decisions of where to locate macroplastic trapping infrastructure difficult. In this research, we conducted a series of experiments in a laboratory channel, exploring the impact of groynes and flexible artificial...
-
A continual model of a damaged medium used for analyzing fatigue life of polycrystalline structural alloys under thermal–mechanical loading
PublikacjaThe main physical laws of thermal–plastic deformation and fatigue damage accumulation processes in polycrystalline structural alloys under various regimes of cyclic thermal–mechanical loading are considered. Within the framework of mechanics of damaged media, a mathematical model is developed that describes thermal–plastic deformation and fatigue damage accumulation processes under low-cycle loading. The model consists of three...
-
Cavity-expansion approximation for projectile impact and penetration into sand
PublikacjaA one-dimensional problem of a spherical cavity expanding at a constant velocity from zero initial radius in an infinite granular medium, which has the first-kind self-similar solution, is considered. We are solving this dynamic spherical cavity-expansion problem to model rigid spheres penetrating into a granular media. Elastic–plastic deformation of the granular media is described in a barotropic approximation, using the high-pressure...
-
Rheology of potato starch chemically modified with microwave-assisted reactions
PublikacjaNative potato starch was sulfated, selenated, borated, silicated and zincatated by means of microwave-assisted reactions with varying doses of relevant reagents. Resulting products were characterized involving rheological behavior of pastes, their weight-average molecular weight (Mw), and radius of gyration (Rg). Most of the pastes showed shear-thinning behavior, with the flow behavior index (n) below unity. The pastes of starch...
-
Emissions of selected monoaromatic hydrocarbons as a factor affecting the removal of single-use polymer barbecue and kitchen utensils from everyday use
PublikacjaThe main focus of this study is the emission of monoaromatic hydrocarbons because these are the preliminary factors of potential solvent and monomer residues present in single-use plastic barbecue and kitchen utensils comprising polystyrene, polypropylene, natural cellulose, and biodegradable polymers intended for use with hot meal or beverages. Herein, the emissions of monoaromatic hydrocarbons (styrene, benzene, toluene, ethylbenzene,...
-
From polymer waste to potential main industrial products: Actual state of recycling and recovering
Publikacjalastics have become widely used materials in everyday life due to their special properties such as durability, easy processing, light-weight and low-cost of production. However, because of their stable and non-biodegradable nature, postconsumer plastics become an issue to the environment. The growing amounts of waste are generated, as plastic products are commonly used only once before disposal. The alternatives of practical techniques...
-
SOLUTIONS OF THE INTERMEDIATE SUPPORT STRUC- TURES OF THE NORTHERN MARMARA HIGHWAY (ISTAN- BUL’S RING ROAD) IN THE CONTEXT OF SEISMIC ACTIVITY
PublikacjaIn 2014–2018, as a result of the expansion of the city of Istanbul in Turkey, a project was imple- mented consisting of building a northern ring road, called the Northern Marmara Highway. The concept of the structural design of the ring road’s intermediate supports aims at constructing sup- ports that according to the TURKISH DLH 2008 standard must comply with the design require- ments for the three calculated earthquake insensitivity...
-
Mechanical Behavior of Bi-Layer and Dispersion Coatings Composed of Several Nanostructures on Ti13Nb13Zr Alloy
PublikacjaTitanium implants are commonly used because of several advantages, but their surface modification is necessary to enhance bioactivity. Recently, their surface coatings were developed to induce local antibacterial properties. The aim of this research was to investigate and compare me-chanical properties of three coatings: multi-wall carbon nanotubes (MWCNTs), bi-layer composed of an inner MWCNTs layer and an outer TiO2 layer, and...
-
Magnetic and infrared thermography methods in detection of antipersonnel landmines
PublikacjaIn this paper the two alternative methods of antipersonnel landmine detection are shown: the magnetic method and the active infrared thermography. The experimental results of the detection of selected, plastic mines using both methods are also presented.
-
New perspective on the in vivo use of cold stress dynamic thermography in integumental reconstruction with the use of skin-muscle flaps
PublikacjaAmong the problems encountered by plastic surgeons is the reconstruction of defects following tumors. One of the reconstructive options is TRAM flap. Despite that anatomy is well-explored, marginal flap necrosis may develop. To minimize complications imaging examinations was designed to determine the degree of flap perfusion. One of them is the thermographic examination.
-
Load introduction to composite columns revisited—Significance of force allocation and shear connection stiffness
PublikacjaThe AISC 360-16 Specification recommends that the design shear force between parts of a composite column in the load introduction area shall be calculated based on the force allocation at ultimate limit state. Applicability of this straightforward method to the load levels that usually arise in slender composite columns is questionable, as this capacity-based force allocation is only true when the axial force is equal to the plastic...
-
Study on extraction and characterization of anchote (Coccinia abyssinica) starch and reinforced enset (Ensete ventricosum) fiber for the production of reinforced bioplastic film
PublikacjaPopulation expansion is causing an increase in dependence on plastic materials. The worst aspects of conventional plastics were their inability to biodegrade, their poor capacity to transmit water vapor, and their production of greenhouse gases. Usages of bioplastics are necessary for the advancement of a green economy and environment in order to eradicate these drawbacks of traditional plastics. In this study, reinforced bioplastic...
-
The experimental and numerical investigation of fracture behaviour in PMMA notched specimens under biaxial loading conditions – Tension with torsion
PublikacjaThis paper presents the results of experimental fracture test of flat PMMA specimens under biaxial loading condition tension with torsion (proportional). The specimens were made in two thicknesses: 5 and 15 mm and were weakened with V-type edge notches with different root radii: 0.5; 2 and 10 mm. Thanks to the ARAMIS 3D 4 M non-contact vision system, measurement of the elongation and twist angle were recorded. During experimental...
-
Wybrane problemy plastyczności w płaskim ośrodku mikropolarnym
PublikacjaW pracy analizuje się sprężysto-plastyczny płaski ośrodek mikropolarny. Do rozwiązań równań plastyczności wykorzystuje się technikę Closest Point Projection Method. Przedstawiono przykład numeryczny w płaskim stanie naprężenia, zasygnalizowano problem lokalizacji w zadaniach z osłabieniem materiału.
-
Numerical Modelling of Connections Between Stones in Foundations of Historical Buildings
PublikacjaThe aim of this paper is to analyse the behaviour of old building foundations composed of stones (the main load-bearing elements) and mortar, based on numerical analysis. Some basic aspects of historical foundations are briefly discussed, with an emphasis on their development, techniques, and material. The behaviour of a foundation subjected to the loads transmitted from the upper parts of the structure is described...
-
Separation of the effects of notch and macro residual stress on the MFL signal characteristics
PublikacjaMagnetic flux leakage (MFL) distribution for three configurations of samples has been investigated in order to study the influence of notch and plastic deformation separately as well as together. Samples have been made of S355 steel. The MFL signal measurements were carried out along the longest dimension of the sample over a length of 120 mm. Two components of magnetic field were measured: 1) tangential to the main axis and 2)...
-
Modelling reinforced concrete beams under mixed shear-tension failure with different continuous FE approaches
PublikacjaThe paper presents quasi-static numerical simulations of the behaviour of short reinforced concrete beams without shear reinforcement under mixed shear-tension failure using the FEM and four various constitutive continuum models for concrete. First, an isotropic elasto-plastic model with a Drucker-Prager criterion defined in compression and with a Rankine criterion defined in tension was used. Next, an anisotropic smeared crack...
-
O zbieżności rozwiązań w nieliniowym mikropolarnym ośrodku sprężysto-plastycznym - zastosowanie elementów skończonych wyższego rzędu.
PublikacjaEfekty lokalizacji w nieliniowym geometrycznie sprężysto-plastycznym mikropolarnym ośrodku z osłabieniem materiału. Hipotezy Hubera-Misesa-Hencky’ego i Druckera-Pragera. Rozwiązanie równań sprężysto-plastycznych przy użyciu algorytmu powrotnego. Opis zastosowanych elementów skończonych. Przykłady numeryczne obliczeń w geotechnice.
-
Experimental study on the behaviour of steel columns under seismic-induced axial impact load
PublikacjaIt has been observed during major earthquakes that the so called soft-storey failure of an upper floor of a structure results in large impact load acting on structural members of the lower storeys. It may further lead to progressive collapse of the whole structure substantially intensifying human and material losses. Therefore, the aim of this paper is to investigate experimentally the behaviour of columns under bending (observed...
-
Super tough interpenetrating polymeric network of styrene butadiene rubber‐poly (methyl methacrylate) incorporated with general purpose carbon black ( N660 )
PublikacjaA classic set of polymeric interpenetrating polymeric network (IPN) microcomposites has been fabricated using an elastomer—styrene butadiene rubber [SBR], a thermoplastic poly(methyl methacrylate)-PMMA and with carbon black (CB)-N660 as a filler and reinforcing agent. This synthesized IPN composite can be promisingly employed as a toughened plastic and vibrational damper in a wide service range with excellent thermal stability,...
-
Numerical analyses of novel prefabricated structural wall panels in residential buildings based on laboratory tests in scale 1:1
PublikacjaThe paper presents experimental and numerical investigations on novel prefabricated composite building wall panels for residential building constructions. The wall panels were composed of reinforced concrete ribbed elements with the core from the EPS foam as the thermal insulation. The wall panels in the full-scale 1:1 were subjected to vertical loads. In the first step, the experiments were analysed with simple usual static methods....
-
Tackling microplastics pollution in global environment through integration of applied technology, policy instruments, and legislation
PublikacjaMicroplastic pollution is a serious environmental problem that affects both aquatic and terrestrial ecosystems. Small particles with size of less than 5 mm, known as microplastics (MPs), persist in the environment and pose serious threats to various species from micro-organisms to humans. However, terrestrial environment has received less attention than the aquatic environment, despite being a major source of MPs that eventually...
-
Inkjet Printing of Lanthanide–Organic Frameworks for Anti-Counterfeiting Applications
PublikacjaPhotoluminescent lanthanide−organic frameworks (Ln-MOFs) were printed onto plastic and paper foils with a conventional inkjet printer. Ln-MOF inks were used to reproduce color images that can only be observed under UV light irradiation. This approach opens a new window for exploring Ln-MOF materials in technological applications, such as optical devices (e.g., lab-on-a-chip), as proof of authenticity for official documents.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 009_v_2
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 009_v_3
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 009_h_3
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 019_v_5
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 009_h_5
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 009_h_4
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 039_h_4
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 019_v_4
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 019_h_5
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 039_v_4
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 009_v_4
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 039_v_3
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 019_v_3
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 019_h_3
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 039_h_5
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 019_h_4
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 039_v_2
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 039_h_3
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
Nanotechnologies in Development of Structural Materials and Biomaterials
PublikacjaThe nanometric materials and technologies resulted in nanostructures are reviewed. The examples of nanomaterials are shown. The typical nanotechnologies, including plastic deformation, mechanical attrition, controlled detonation, hot plasma jet synthesis, laser vaporisation, CVD and PVD, mechanical milling, annealing, ultrasonic irradiation, nanolithography, electrocrystallisation, electrospinning, sol-gel method, cryogenic laser-enhanced...
-
WERYFIKACJA KONCEPCJI PRZEGUBÓW PLASTYCZNYCH PROJEKTOWANYCH NA ODZIAŁYWANIA SEJSMICZNE WIADUKTU V6 OBWODNICY ISTAMBUŁU
PublikacjaW pracy zawarto wyniki analiz betonowego wiaduktu V6 budowanego w ciągu obwodnicy Istambułu w Turcji realizowanego w ramach projektu Northern Marmara Highway. Przeprawę stanowią dwie niezależne nitki o skrzynkowym przekroju poprzecznym i szerokości 22,00 m. Schemat statyczny obiektu to belka dziewięcioprzęsłowa o długości całkowitej 446,86 m oparta na podporach słupowych o zmiennej sztywności (rys.1) i wysokościach zmieniających...
-
"Raport z wstępnych badań własności stali trudnościeralnej 460HB",. ang "Report on preliminary tests of the properties of wear-resistant steel 460HB"
PublikacjaMikrostrukturę badanej stali trudnościeralnej 460HB stanowi drobnoziarnisty martenzyt odpuszczony, który jest właściwy dla stali konstrukcyjnych niskowęglowych, niskostopowych ulepszonych cieplnie. W przypadku blach grubych, do których zalicza się badana stal, struktura może ulec zaburzeniu, jeżeli w hutniczym procesie wytwórczym wystąpiła niejednorodność odkształcenia plastycznego i w konsekwencji tworzenie się pasm segregacyjnych,...
-
Launching of steel bridge girder. Application of nonlinear shell models
PublikacjaThe paper describes the final technology of launching the steel bridge superstructure. The original technology failed in the first construction stage. Local damage of steel webs caused by plastic buckling stopped the procedure. In the effect of damage a new consulting team was employed to solve the problem and redesign a technology of constructing. The key element of the new solution was developed with great help of non-linear...