Filtry
wszystkich: 802
Wyniki wyszukiwania dla: Diesel Fuel Spray
-
The concept of research on ecological, energy and reliability effects of modified marine fuel oils application to supply compression-ignition engines in real conditions
PublikacjaWithin the article, basic assumptions of the research project financed by Regional Fund for Environmental Protection and Water in Gdansk were described. The project concerns the experimental investigations carried out on laboratory compression-ignition engine in conditions of its supply with a non-standard marine fuel oil. Configuration and measuring capability of laboratory test bed presently being constructed were introduced....
-
Preconcentration and Analytical Methods for Determination of Methyl Tert-Butyl Ether and Other Fuel Oxygenates and Their Degradation Products in Environment: A Review
PublikacjaFuel oxygenates (FOs) are mainly ethers or alcohols which are added to gasoline either to boost the octane number or to make the fuel burning process more "cleaner" with increasing the oxygen content, or to obtain a combination of both effects. FOs are water soluble with high mobility in the environment which presence even at very low concentrations lower the quality of water making it unsafe or unpleasant due to their objectionable...
-
Possible use of combined diesel engine/steam turbine in ship power plant = Możliwości zastosowania układów kombinowanych: silnik diesla - turbina parowa w siłowniach okrętowych
PublikacjaW artykule przedstawiono układ kombinowany dużej mocy. Składa się on z silnika spalinowego tłokowego oraz skojarzone z nim układu turbiny parowej, wykorzystującego energię spalin wylotowych. Rozpatrzono tylko wariant silnik Diesla - turbina parowa, z kotłem utylizacyjnym jednociśnieniowym. Podano założenia i ograniczenia oraz wyniki obliczeń z opracowanego programu komputerowego. Obliczenia numeryczne wykonano dla silników spalinowych...
-
Evaluation of the significance of the effect of the active cross-sectional area of the inlet air channel on the specific enthalpy of the exhaust gas of a diesel engine using statistics F of the Fisher-Snedecor distribution
PublikacjaThis paper presents the application of Fisher-Snedecor distribution F statistics to assess the significance of the influence of changes in the active cross-sectional area of the inlet air channel (Adol) flow in a diesel engine on the observed diagnostic parameter determined on the basis of measurements of the quick changing exhaust gas temperature in the outlet channel, which is the specific enthalpy of the exhaust gas stream within...
-
Application analysis of a hybrid solid oxide fuel cell-gas turbine system for marine power plants
PublikacjaThe results of theoretical studies of the possibilities of using hybrid solid oxide fuel cell–gas turbine (SOFC-GT) systems for marine power plants are presented. A 500 kW auxiliary marine power plant scheme using stacks of SOFCs in combination with a regenerative gas turbine operating with over-expansion based on our recent patent application is proposed. The results of mathematical modelling showed the opportunity to obtain a...
-
Diagnosis´ likelihood and diagnosis rightness about the technical state of diesel engine
PublikacjaW referacie uzasadniono potrzebę rozróżniania pojęć "wiarygodność diagnozy" i "trafność diagnozy" przy podejmowaniu decyzji eksploatacyjnych. Wyprowadzono wzór na prawdopodobieństwo sformułowania diagnozy jako miary wiarygodności diagnozy. Do wyprowadzenia tego wzoru zastosowano teorię procesów semimarkowskich oraz wzór Bayesa na prawdopodobieństwo warunkowe.
-
Journal of Nuclear Fuel Cycle and Waste Technology
Czasopisma -
Palm Oil Fuel Ash-Based Eco-Efficient Concrete: A Critical Review of the Short-Term Properties
PublikacjaThe huge demand for concrete is predicted to upsurge due to rapid construction developments. Environmental worries regarding the large amounts of carbon dioxide emanations from cement production have resulted in new ideas to develop supplemental cementing materials, aiming to decrease the cement volume required for making concrete. Palm-oil-fuel-ash (POFA) is an industrial byproduct derived from palm oil waste’s incineration in...
-
Tyre rolling resistance and its influence on fuel consumption
PublikacjaRolling resistance of tyres is one of the major resistive forces acting on any wheeled vehicle. Unfortunately, it is also one of the forces very difficult to measure. It is estimated that in certain traffic conditions (like for example constant speed driving with slow or moderate speed) so called Rolling Resistance Impact Factor may be as high as 0.3. This means that reduction of rolling resistance by 50% would lead to 15% of energy...
-
Dimethyl ether (DME) as potential environmental friendly fuel
Publikacja -
Micro solid oxide fuel cells and their fabrication methods
PublikacjaW pracy przedstawiono obecny stan badań związany z tlenkowymi microogniwami paliwowymi oraz metodami ich wytwarzania.
-
Properties of glass-ceramic for solid oxide fuel cells
PublikacjaW pracy przedstawiono właściwości krystalicznych pyro- i orto- krzemowych szkieł przygotowanych dla tlenkowych ogniw paliwowych. Zbadano rozszerzalnoność, ubytek masy, zmiany widm rentgenograficznych oraz widm impedancyjnych dla szkieł narażonych przez 60 dni na atmosfere ulteniajacą i redukująca w temperaturze 800C.
-
Micro solid oxide fuel cells and their fabrication methods
PublikacjaW pracy przedstawiono obecny stan badań i tendencje w rozwoju tlenkowych ogniw paliwowych.
-
Influence of stack temperature on PEM fuel cell performance
PublikacjaW pracy przedstawiono wpływ temperatury stosu na wydajność ogniwa paliwowego typu PEM dla zadanego obciążenia. Badania ogniwa paliwowego przeprowadzono dla sześciu temperatur pracy stosu z zakresu od 30 oC do 65 oC. Dla najwyższej temperatury stosu, tj. 65 oC, wydajność pracy ogniwa paliwowego była najwyższa. Wraz ze wzrostem temperatury stosu zarejestrowano spadek mocy ogniwa paliwowego od 1015 W dla temperatury 30 oC do 1004...
-
A novel technology of solid oxide fuel cell fabrication
PublikacjaW pracy przedstawiono metodę wytwarzania wartstw i materiałów elektroceramicznych. Metoda jest kombinacją metod nanoszenia szkieletu z proszków ceramicznych i prekursorów polimerowych. Umożliwia ona otrzymanie zarówno gęstych jak i porowatych warstw i materiałów jednorodnych oraz kompozytowych. W pracy przedstawiono przykłady struktur dla tlenkowych ogniw paliwowych.
-
Advanced XAS analysis for investigating fuel cell electrocatalysts
PublikacjaW pracy została zaprezentowana analiza XAFS nanocząstek platyny używanych jako materiał katalityczny w niskotemperaturowych ogniwach paliwowych. Analiza danych EXAFS została przeprowadzona za pomocą zaawansowanej metody GNXAS, w której wzięto pod uwagę rozkład rozmiaru granul nano-platyny i niejednorodność warstwy katalitycznej elektrody, badane za pomocą SEM (skaningowy mikroskop elektronowy), TEM (transmisyjny mikroskop elektronowy)...
-
Recent anode advances in Solid Oxide Fuel Cells
PublikacjaW pracy podsumowano bieżące doniesienia na temat potencjalnych materiałów anodowych dla wysokotemperaturowych tlenkowych ogniw paliwowych z uwzględnieniem wyników otrzymanych przez autora pracy.
-
Solid oxide fuel cells for distributed energy generation
PublikacjaW pracy przedstawiono zasadę działania tlenkowego ogniwa paliwowego. Zaprezentowano wybrane problemy oraz rozwiązania technologiczne.
-
On-line Impedance Monitoring of Direct Methanol Fuel Cell
PublikacjaW niniejszej pracy została przedstawiona technika badawcza Dynamiczna Elektrochemiczna Spektroskopia Impedancyjna w obszarze badań ogniw paliwowych. Obiektem badań było ogniwo paliwowe zasilane bezpośrednio metanolem. Badano on-line wpływ zmian warunków pracy na globalną impedancję ogniwa. Podczas pomiarów zmianie ulegała temperatura, natężenia przepływu utleniacza oraz obciążenie.
-
Diagnostic Analysis of Exhaust Gas with A Quick-Changing Temperature from a Marine Diesel Engine Part II / Two Factor Analysis
PublikacjaThe article presents a continuation of research carried out to determine the effect of input parameters (changes in engine structure parameters) on selected output parameters (diagnostic measures), based on quickly changing exhaust gas temperature. A method of determining the simultaneous influence of two input factors (the structure parameter and the engine load) on one output factor was presented, as well as an evaluation...
-
SEM images of Solid Oxide Fuel Cell interface with La0.6Sr0.4Co0.2Fe0.8O3-δ oxygen electrodes sintered at 1050 °C before and after test
Dane BadawczeThis dataset contains cross section SEM images of Solid Oxide Fuel Cell interface with La0.6Sr0.4Co0.2Fe0.8O3-δ oxygen electrode sintered at 1050 °C before and after test. The cell was tested using Open Flanges™ test Set-up at 700 °C. During the test, the cell was aged for approximately 120 hours at a load of 0.5 A/cm^2. Images were obtained using...
-
SEM images of Solid Oxide Fuel Cell interface with Sr0.95Ti0.30Fe0.70O3-d oxygen electrodes sintered at 800 °C before and after test
Dane BadawczeThis dataset contains cross section SEM images of Solid Oxide Fuel Cell interface with Sr0.95Ti0.30Fe0.70O3-d oxygen electrode sintered at 800 °C before and after test. The cell was tested using Open Flanges™ test Set-up at 700 °C. During the test, the cell was aged for approximately 120 hours at a load of 0.5 A/cm^2. Images were obtained using a FEI...
-
DIAGNOSTIC INFORMATION ANALYSIS OF QUICKLY CHANGING TEMPERATURE OF EXHAUST GAS FROM MARINE DIESEL ENGINE PART I SINGLE FACTOR ANALYSIS
PublikacjaIn this paper, attention was paid to the problem of low controllability of marine medium- and high-speed engines during operation, which significantly limits the parametric diagnosis. The measurement of quickly changing temperature of engine exhaust gas was proposed, the courses of which can be a source of diagnostic information. The F statistic of the Fisher-Snedecor distribution was chosen as a statistical tool. Laboratory tests...
-
Design and characterization of apatite La9.8Si5.7Mg0.3O26±δ-based micro-tubular solid oxide fuel cells
PublikacjaIn this study, electrolyte-supported (Cell A) and anode-supported (Cell B) micro-tubular solid oxide fuel cells (SOFCs) based on the La9.8Si5.7Mg0.3O26±δ (LSMO) electrolyte is built through an extrusion and dip-coating processes. The formulations and process conditions for these cells are established and optimized. Both cell configurations show no visible delamination or cracking, and reaction zones and inter-diffusion of any species...
-
The influence of synthesis method on the microstructure and catalytic performance of Y 0.07 Sr 0.93 Ti 0.8 Fe 0.2 O 3-δ in synthetic biogas operated solid oxide fuel cells
PublikacjaThe Y0.07Sr0.93Ti0.8Fe0.2O3-δ (YSTF) material was fabricated using three different synthesis methods: modified polymer precursor method (MPP), Pechini method and a solid state reaction method. It was applied as an anode catalytic material for biogas reforming in solid oxide fuel cells. Clear differences in the microstructure of fabricated catalytic layers were found, mainly with respect to a grain size and distribution of grains....
-
In situ study of a composition of outlet gases from biogas fuelled Solid Oxide Fuel Cell performed by the Fourier Transform Infrared Spectroscopy
PublikacjaThe purpose of this study was to develop a method and software based on the Fourier Transform Infrared Spectroscopy for the in-situ, quantitative analysis of the composition of outlet gases from Solid Oxide Fuel Cell (SOFC). The calibration procedure performed at the beginning of the experiment indicated a polynomial dependence between the concentration of a calibrating gas (CO, CO2, CH4) and the corresponding integrated absorbance in...
-
Low temperature processed MnCo2O4 and MnCo1.8Fe0.2O4 as effective protective coatings for solid oxide fuel cell interconnects at 750 °C
PublikacjaIn this study two materials, MnCo2O4 and MnCo1.8Fe0.2O4 are studied as potential protective coatings for Solid Oxide Fuel Cell interconnects working at 750 °C. First powder fabrication by a modified Pechini method is described followed by a description of the coating procedure. The protective action of the coating applied on Crofer 22 APU is evaluated by following the area specific resistance (ASR) of the scale/coating for 5500...
-
Fault Tree Analysis and Failure Diagnosis of Marine Diesel Engine Turbocharger System
Publikacja -
INFLUENCE OF THE MARINE 4-STROKE DIESEL ENGINE MALFUNCTIONS ON THE NITRIC OXIDES EMISSION
Publikacja -
The Influence of Synthetic Oxygenates on Euro IV Diesel Passenger Car Exhaust Emissions
Publikacja -
Concept for interpretation and assessment of slide bearings operation in Diesel enfines in probabilistic approach
PublikacjaW artykule zaproponowano interpretację wartościującą działania, które (podobnie jak przedstawione w mechanice klasycznej działania Hamiltona i Maupertiusa oraz działanie wynikające ze zmiany pędu ciała) jest rozpatrywane jako wielkość fizyczna o jednostce miary zwanej''dżulosekundą''. Przedstawiono propozycję ilościowej interpretacji działania dowolnego poprzecznego łożyska ślizgowego, w którym zachodzą oddziaływania energetyczne...
-
Loads of ship main diesel engine in the aspect of practical assessment of its operation
PublikacjaW artykule przedstawiono koncepcję metody pozwalającej na ocenę działania silnika pracującego na obciążeniu częściowym. Do określenia istniejącego zapasu parametrów użytkowych silnika oraz związanych z degradacją jego stanu technicznego dodatkowych kosztów ponoszonych przez użytkownika wykorzystane zostało wartościujące (ilościowe) ujęcie działania interpretowanego jako pewna wielkość fizyczna.
-
Effects of Contamination with Gasoline and Diesel Oil on Shear Strength of Coarse Grained Soil
Publikacja -
Dual fuelling of truck CI engine with diesel oil and mixture of propane and butane
PublikacjaW artykule przedstawiono zasadę działania dwupaliwowego zasilania jednocześnie olejem napędowym i odparowanym LPG silnika samochodu ciężarowego. Pokazano korzyści wynikające ze zużycia tańszego paliwa zbadane doświadczalnie.
-
The time of the first transition of the semi-Markov process in the evaluation of diesel engine operation
PublikacjaW referacie przedstawiono rozwinięcie prezentowanej w literaturze metody ilościowej oceny działania na przykładzie okrętowego silnika głównego z zapłonem samoczynnym. Według tej interpretacji, działanie silnika może zostać przedstawione jako wielkość fizyczna. W tym aspekcie, na przykładzie okrętowego silnika napędu głównego dokonano oceny przydatności tej wielkości do opisu własności niezawodnościowych silnika. Precyzyjne określenie...
-
Influence of temperature and nitrogen pressure on the test without active gases for high-temperature proton exchange membrane fuel cells
PublikacjaHigh-Temperature Proton-Exchange Membrane Fuel Cells (HT-PEMFCs) are a candidate for electrical energy supply devices in more and more applications. Most notably in the aeronautic industry. Before any use, an HT-PEMFC is preheated and after that supplied with its active gases. Only at this state, the diagnostics can be performed. A method of testing not requiring a complete start-up would be beneficial for many reasons. This article...
-
Physical and sealing properties of BaO–Al2O3–SiO2–CaO–V2O5 glasses for solid oxide fuel cell applications
PublikacjaIn this study, the properties of BaO–Al2O3–SiO2 (SAB) glasses incorporated with CaO and V2O5 as the network modifier and additive, respectively, are evaluated. The electrical resistivities of the glasses decrease upon the addition of CaO but increase upon increasing their V2O5 content because the V5+ species lower the ionic mobility of the glasses. The addition of V2O5 improves the wettability of the glasses on the Crofer 22 APU...
-
Optimization Model to Manage Ship Fuel Consumption and Navigation Time
Publikacja -
Spectroscopic investigations into degradation of polymer membranes for fuel cells applications
Publikacja -
Chapter 8 : Possibilities of operating fuel consumption estimation of vehicles
PublikacjaPrzedstawiona w pracy metoda umożliwia ocenę eksploatacyjnego zużycia paliwa pojazdu samochodowego dzięki porównaniu zarejestrowanego zużycia paliwa z referencyjnym dla tych samych warunków eksploatacji. Warunki te mogą wynikać zarówno z lokalnej specyfiki ruchu pojazdów jak również ze sposobu prowadzenia auta przez kierowcę. Zgodnie z przyjętą metodą warunki te mogą zostać w bardzo prosty sposób zarejestrowane w czasie codziennej...
-
Dynamic response of the PEM fuel cell to step change load
PublikacjaPrzedstawiono charakterystyki dynamiczne ogniwa paliwowego typu PEM o mocy 2.5 kW obciążanego sygnałem skokowym o wartościach od 1 A do 50 A.
-
Dynamic response of the PEM fuel cell to variable load conditions
PublikacjaOpisano układ zasilania oparty na 2 ogniwach paliwowych typu PEM o mocy 1.2 kW każde. Omówiono problem ograniczenie ogniwa paliwowego przez drugą zasadę termodynamiki. Przedstawiono charakterystyki układu w zależności od sygnału obciążenia typu: skok jednostkowy, półsinusoidalny, trójkątny, prostokątny i trapezowy.
-
Metal Supported Solid Oxide Fuel Cells - Selected Aspects
PublikacjaW artykule przedstawiono wyniki badań nad tlenkowymi ogniwami paliwowymi zbudowanymi na stalowym interkonektorze.
-
Nanocrystalline doped zirconia and ceria films for fuel cell application
PublikacjaW artykule przestawiono porównanie właścowości warstw nanokrystalicznych przygotowanych w technologii 'net-shape'. Materiały te mają zastosowanie w tlenkowychogniwach paliwowych.
-
Simulation of ammonia combustion in dual-fuel compression-ignition engine
Publikacja -
Influence of the use of ethanol fuel on selected parameters of the gasoline engine
Publikacja -
Solid oxide fuel cells with Ni-infiltrated perovskite anode
PublikacjaWytworzono próbki na bazie tytanianu strontu domieszkowanego niobem i przebadano wpływ nasączania niklem na właściwości tych materiałów.
-
The influence of fuel type on heat balance of medium-speed engine
PublikacjaW artykule zaprezentowano analizę wpływu rodzaju zastosowanego paliwa na bilans cieplny silników średnioobrotowych stosowanych w energetyce stacjonarnej. Przedmiotem analizy są silniki ZS i ZI zasilane gazem ziemnym oraz silniki ZS zasilane olejem napędowym. Dodatkowo analizę uzupełniono o wyniki obliczeń wykonanych dla silników dwupaliwowych, tzn. silników, w których zapłon mieszanki paliwowo gazowej realizowany jest przez pilotażowy...
-
Low-temperature processed anode for Solid Oxide Fuel Cells
PublikacjaPrzygotowano i przebadano kompozytową anode Ni/YSZ, która została przygotowana z wykorzystaniem technologii net shape. Wyniki potwierdziły, że kompozyt może być wykorzystany jako potencjalna anoda w tlenkowych ogniwach paliwowych.
-
Nanocrystalline doped zirconia and ceria films for fuel cell application
PublikacjaW artykule przedstawiono i porównano właściwości nanokrystalicznych warstw ceramicznych przygotowanych na bazie tlenku ceru i tlenku cyrkonu.