Filtry
wszystkich: 2033
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: load carrying capacity
-
Communication and Load Balancing Optimization for Finite Element Electromagnetic Simulations Using Multi-GPU Workstation
PublikacjaThis paper considers a method for accelerating finite-element simulations of electromagnetic problems on a workstation using graphics processing units (GPUs). The focus is on finite-element formulations using higher order elements and tetrahedral meshes that lead to sparse matrices too large to be dealt with on a typical workstation using direct methods. We discuss the problem of rapid matrix generation and assembly, as well as...
-
Screw displacement pile shaft deformations measured by vibrating wire and fiber optic systems during a static load test
PublikacjaThis paper describes a full scale static load test performed on a 400 mm diameter screw displacement pile equipped with four different strain measuring systems. Three types of vibrating wire strain gauges (VWSG) were used: global - retrievable, local attached to steel pipe and local concrete embedded. The fourth system was distributed fiber optic sensors based on Rayleigh back scattering (DFOS) - three in the pile cross section....
-
Effect of shallow traps on admittance spectra of the system carrying SCLC and on values of charge carrier mobility extracted from susceptance
PublikacjaThe work concerns small-signal spectra of space-charge-limited current below threshold frequency (ft) of shallow traps. It is shown that below ft the small-signal concentration of trapped charge carriers is proportional to and in phase with small-signal concentration of free charge carriers, so there is no room for “slow shallow traps”. Conductance can be reduced by the traps, however no change in the range of real capacitance...
-
Finite element modeling of plastic hinges based on ductility demand-capacity method using nonlinear material for dynamic analysis
PublikacjaThe article discusses modeling plastic hinges in reinforced concrete interme-diate supports using finite elements methods. The ductility demand-capacitymethod was used to determine the geometrical parameters of cross-section plas-ticization zones, their ability to move and rotate, as well as their ductility. Dueto the varied geometry and stiffness of the supports and their nonlinear behav-ior under dynamic load, this method was...
-
Mathematical modeling and prediction of pit to crack transition under cyclic thermal load using artificial neural network
PublikacjaThe formation of pitting is a major problem in most metals, which is caused by extremely localized corrosion that creates small holes in metal and subsequently, it changes into cracks under mechanical load, thermo-mechanical stress, and corrosion process factors. This research aims to study pit to crack transition phenomenon of steel boiler heat tubes under cyclic thermal load, and mathematical modeling...
-
Influence of Installation Effects on Pile Bearing Capacity in Cohesive Soils – Large Deformation Analysis Via Finite Element Method
PublikacjaIn this paper, the whole process of pile construction and performance during loading is modelled via large deformation finite element methods such as Coupled Eulerian Lagrangian (CEL) and Updated Lagrangian (UL). Numerical study consists of installation process, consolidation phase and following pile static load test (SLT). The Poznań site is chosen as the reference location for the numerical analysis, where series of pile SLTs...
-
An approach for the response of buildings subjected to impact load after soft-story failure due to earthquake excitation
Publikacjahe soft-story failure is one of the most typical types of damage observed in buildings during earthquakes. The failure of an intermediate soft story of a structure results in large impact loading acting on the lower floors due to the fall of the upper stories. The aim of the present paper is to study the behavior of the structural members exposed to such extreme load conditions occurring under ground motion excitation. Special...
-
A negative effect of carbon phase on specific capacity of electrode material consisted of nanosized bismuth vanadate embedded in carbonaceous matrix
PublikacjaLithium-ion batteries (LIBs) are widely used all over the world. The LIBs belong to a renewable energy source and energy storage devices. The increase in energy demand causes that new materials of higher energy and higher power densities are still under investigation. Herein, we compare electrochemical properties of bismuth vanadate (BiVO4) embedded and not embedded into carbonaceous matrix as an anode material along with structural...
-
The influence of compressive gear on maximal load lifted in competitive powerlifting.
Publikacja -
Refining and integrating schizophrenia pathophysiology – Relevance of the allostatic load concept
Publikacja -
Propeller Load Modelling In The Calculations Of Marine Shafting Torsional Vibrations
Publikacja -
Dynamic response of the PEM fuel cell to variable load conditions
PublikacjaOpisano układ zasilania oparty na 2 ogniwach paliwowych typu PEM o mocy 1.2 kW każde. Omówiono problem ograniczenie ogniwa paliwowego przez drugą zasadę termodynamiki. Przedstawiono charakterystyki układu w zależności od sygnału obciążenia typu: skok jednostkowy, półsinusoidalny, trójkątny, prostokątny i trapezowy.
-
Dynamic response of the PEM fuel cell to step change load
PublikacjaPrzedstawiono charakterystyki dynamiczne ogniwa paliwowego typu PEM o mocy 2.5 kW obciążanego sygnałem skokowym o wartościach od 1 A do 50 A.
-
Modeling of Wireless Traffic Load in Next Generation Wireless Networks
Publikacja -
DISPLACEMENT MEASUREMENTS DURING LOAD TESTING OF THE RAILWAY ARCH BRIDGE
Publikacja -
Cam mechanism designing with account of the technological load and energy costs
Publikacja -
Eigenvalue approach to synthesis of prototype filters with source/load coupling
PublikacjaArtykuł przedstawia nową, szybko zbieżną, technikę syntezy macierzy sprzężeń filtrów o charaktrystyce Czebyszewa. Synteza opiera się na zastosowaniu metody najmniejszych kwadratów w odniesieniu do wartości własnych macierzy sprzężeń oraz jej podmacierzy.
-
On bounded load routings for modeling k-regular connection topologies
PublikacjaW pracy analizowane są problemy modelowania k-regularnych topologii sieci komputerowych z punktu widzenia routingu typu point-to-point. Zaprezentowane są algorytmy oraz przeprowadzona jest analiza złożoności obliczeniowej.
-
Advanced control of induction motor based on load angle estimation.
PublikacjaW artykule przedstawiono układ sterowania silnikiem asynchronicznym klatkowy wykorzystujący estymację kąta obciążenia pracujący bez pomiaru prędkości obrotowej. W artykule przedstawiono zasadę działania układu i motodę odtwarzania zmiennych opartą w części o zależności stanu ustalonego. Przedstawiono zrealizowany regulator rozmyty kąta obciążenia. Zaprezentowane zostały wyniki symulacji i eksperymentu przeprowadzone z użyciem...
-
Advanced current regulated PWM inverter with simplified load model.
PublikacjaW artykule przedstawionio nowy regulator prądu stojana silnika asynchronicznego zasilanego z falownika napięcia. Regulator wykorzystuje obliczenia siły elektromotorycznej silnika. Rozważonio wpływ zmian parametrów silnika na działanie regulatora. Wykorzystano uproszczony model silnika bez uwzględnienienia rezystancji stojana. Zastosowano stałą częstotliwość próbkowania prądu. Układ zrealizowania w programie symulacyjnym oraz na...
-
EXPERIMENTAL STUDY OF A TEMPORARY STEEL GRANDSTAND UNDER CROWD LOAD
PublikacjaTemporary structures, such as grandstands, are commonly used during different types of mass events, especially sport and music concerts. In this paper, the results of the experimental study on temporary steel grandstand are presented. The aim of the investigation was to determine modal characteristics of such structures. Modes of free vibrations and corresponding natural frequencies have been obtained for empty and occupied grandstand....
-
Calculation of the Effects of Implementing a DSM Electricity Demand Management Strategy Using the Example of Analysis of Changes in the Power System Load
PublikacjaThe paper presents the impact of implementing Demand Side Management (DSM) solutions through proper management and control of the process of charging and discharging electric car batteries. As a result, the daily load curves were shaped so as to fill valleys and cut down peaks. Therefore, the implementation of power demand management solutions had a significant impact on the power system operation. The impact of DSM solutions manifested...
-
Comparison of the powers of energy losses in a variable capacity displacement pump determined without or with taking into account the power of hydraulic oil compression
PublikacjaPowers of energy losses in a variable capacity displacement pump are compared with or without taking into account the power of hydraulic oil compression. Evaluation of power of liquid compression in the pump was made possible by the use of method, proposed by the Author, of determining the degree of liquid aeration in the pump. In the method of determining the liquid aeration in the pump and of powers of volumetric losses of liquid...
-
Methodology for carrying out measurements of the tombolo geomorphic landform using Unmanned Aerial and Surface Vehicles near Sopot pier, Poland
Publikacja -
"FEM Parametric Study on Ultimate Bearing Capacity of CFST Arch Bridge
Publikacja -
The Impact of Shrubby Floodplain Vegetation Growth on the Discharge Capacity of River Valleys
Publikacja -
Anserine and carnosine supplementation in the elderly: Effects on cognitive functioning and physical capacity
Publikacja -
Antioxidant capacity and cholinesterase inhibiting properties of dietary infusions with Humulus lupulus
Publikacja -
Determination of the bearing capacity of pile foundations based on CPT test results
PublikacjaAnalityczne określanie pełnej krzywej obciążenie - osiadanie na podstawie parametrów geotechnicznych wciąż stanowi bardzo trudne zadanie naukowe i inżynierskie. W pracy przedstawiono metodę bezpośredniego wykorzystania oporów na stożku sondy statycznej do określania pełnej krzywej osiadania dla pali Vibro-Fundex. W sumie jako materiał weryfikacyjny wykorzystano 94 próbne obciążenia statyczne pali.
-
Supplementation of garlic lowers lipids and increases antioxidant capacity in plasma of rats
PublikacjaZbadano bioaktywność surowego i gotowanego czosnku (Allium sativium L.). Stwierdzono, że gotowanie czosnku w temperaturze 100 °C przez 20 minut nie wpływa na jego bioaktywność.Samcom szczurów (z badanej populacji) podzielonym losowo na 10 grup, podawano żywność z różnym dodatkiem czosnku. Natomiast grupa kontrolna była karmiona dietą podstawową złożoną ze skrobi pszenicznej, oleju sojowego, celulozy, minerałów i mieszaniny witamin....
-
The concept of weighted mean friction angle in bearning capacity of footings of sands
PublikacjaZagadnienie średniej ważonej kąta tarcia wewnętrznego w nośności fundamentów posadowionych w gruntach niespoistych.
-
The influence of dynamic load changes on temporary impedance in hydrogen fuel cells, selection and validation of the electrical equivalent circuit
PublikacjaTo achieve optimal performance of a fuel cell, a reliable monitoring and diagnostic method is required. The currently utilized methods give limited information or they are impossible to use under dynamic working conditions. To obtain comprehensive information about the fuel cell operation we utilized novel dynamic electrochemical impedance spectroscopy. Impedance measurements in dynamic mode were performed on a hydrogen fuel cell,...
-
Measurements of radiation emission of a portable power bank with a capacity of 5200 mAh
Dane BadawczeThe dataset contains the emission measurement results that are part of comprehensive tests carried out for portable power banks with different capacities. The measurements were performed in the frequency range from 30 MHz to 3 GHz using a Gigahertz Transverse Electromagnetic (GTEM) cell. The test setup was configured to measure a portable power bank...
-
Lateral load resistance of piled raft foundation - A case study of District Jail, Saidu Sharif, Swat Pakistan
PublikacjaPiled raft foundations under lateral loads are usually designed as a pile group, ignoring the contribution of the raft to resisting the lateral loads. In this paper, a case study was performed to determine the raft's contribution to the lateral load resistance. This study analyzed a pile-supported reinforced concrete retaining wall for two different foundation conditions, i.e., pile group foundation and pile raft foundation. Pile group...
-
Mechanical properties of single V2O5 nanocrystal - nanoindentation measurement in control of the max-load
Dane BadawczeThe DataSet contains the nanoindentation curves (indentation force Fn vs penetrationPd) for a single V2O5 nanocrystal supported on a substrate. The measurements were performed in control of the maximum load of Berkovich indenter force from 2 to 50 mN.
-
Compensation of supply current harmonics, reactive power, and unbalanced load current balance in the closed-loop control of a shunt active power filter
PublikacjaThis paper presents the compensation tasks performed by a shunt active power filter, including compensation of harmonic currents, reactive power, and an unbalanced load current. The paper demonstrates novel control of the shunt active power filter in a closed-loop system. The control algorithm was verified by performing simulations and compared the simulated results with those obtained in an open-loop control system. All simulations...
-
Fianl report on carrying out tasks within the project Best Agers Lighthouses - strategic age management for SME in the Baltic Sea Region.
PublikacjaThe report presents the origin of the project, as well as its characteristics and aims. Project partners are workpackages are described and main project results are listed. the report is concluded with the part dedicated to dissemination measures carried out within the project
-
Optimization of multilayer rail substrate under moving load, using metamaterials.
Publikacja -
Load Test of Railway Viaduct Built Using Crosswise Launching Technology
Publikacja -
Determination of Stent Load Conditions in New Zealand White Rabbit Urethra
Publikacja -
Large elastic deformations of laminated cylindrical panels under point load
PublikacjaTematem pracy jest numeryczna analiza sprężysta cylindrycznych powłok kompozytowych w zakresie dużych obrotów. Analizując serię wielowarstwowych cylindrycznych powłok kompozytowych o brzegach utwierdzonych i obciążonych centralnie siła skupioną z pewnym zaskoczeniem zaobserwowano, że w przypadku określonych schematów uwarstwienia, nastąpić może wzrost wielkości obciążenia krytycznego mimo redukcji globalnej sztywności konstrukcji.
-
The assessment of load-settlement curve for Atlas piles correlated with CPT tests
PublikacjaRacjonalne stosowanie pali przemieszczeniowych typu Atlas wymaga analitycznej oceny pełnej krzywej obciążenie - osiadanie. W pracy przedstawiono możliwości wykorzystania metody funkcji transformacyjnych t-z (dla pobocznicy) oraz q-z (dla podstawy) dla oceny krzywej osiadania. Jednostkowe graniczne opory na pobocznicy, tmax, oraz pod podstawą, gf, określono na podstawie metody bezpośredniej, wykorzystując opory stożka sondy, qc....
-
Determination of operational load parameters of dredge pumps under dredging operations
PublikacjaArtykuł przedstawia propozycję metody określania parametrów rozkłądów eksploatacyjnych obciążeń, jednego z najważniejszych odbiorników energii mechanicznej na pogłębiarkach - pomp pogłębiarskich (gruntowych). Metoda wykorzystująca wyniki własnych badań eksploatacyjnych, odnosi się do dwóch podstawowych stanów eksploatacji pomp pogłębiarskich, a mianowicie do stanu nazywanego załadunkiem ładowni gruntowej (pogłebiarki lub szalandy)...
-
Application of load-transfer functions method for the analysis of the work of CFA piles
PublikacjaPrzeanalizowano kilkanaście wyników badań nośności pali CFA z kilku krajowych budów. We wszystkich przypadkach pale zakończone były w piaskach. Wyniki zinterpretowano za pomocą funkcji transformacyjnych. Oszacowano przebieg mobilizacji i wartości graniczne oporów gruntów wzdłuż pobocznic i pod podstawami pali.
-
Allostatic load index and its clinical correlates at various stages of psychosis
Publikacja -
Analysis of the cyclic load-unload-reload tests of VALMEX aged fabric
PublikacjaThe paper presents mechanical response of the VALMEX fabric during the cyclic loading-unloading and re-loading experiments. Two types of the aged material used for nearly 20 years as the roofing of the Forest Opera in Sopot (Poland) have been tested. The results have been separately obtained for the warp and fill di-rections. The comparative analysis has revealed that the material aged in service is more durable in the fill di-rection,...
-
Problems of strength modelling of steel sandwich panels under in-plate load
PublikacjaW pracy omówiono zagadnienia wytrzymałości statycznej stalowych paneli typu sandwich spawanych laserowo. Omówiono charakterystyki sztywności podczas zginania, przedstawiono zachowanie pod obciążeniem równomiernie rozłożonym a także sposób niszczenia pod obciążeniem ściskającym. Omówiono możliwości stosowania takich konstrukcji na podstawie wniosków z badań.
-
Stochastic model of the load spectrum for main engines of sea-going ships
PublikacjaW artykule przedstawiono możliwość zastosowania procesów semimarkowskich do probabilistycznego opisu widma obciążeń silników o zapłonie samoczynnym, zastosowanych do napędu statków - czyli silników głównych. W rozważaniach uwzględnione zostały charakterystyki zewnętrzne mocy tego rodzaju silników. Umożliwiły one sformułowanie czteroelementowego zbioru stanów procesu obciążeń tego rodzaju silników. Do opisu rzeczywistego procesu...
-
Going into the research of dampers configuration for bodies under double load conditions.
PublikacjaJednym z etapów projektowania układów mechanicznych jest dobranie wartości sztywności i tłumienia elementów i dopasowanie ich do planowanego zachowania mechanizmu. Proces ten można uprościć, gdy uda się połączyć komputerowe modelowanie mechanizmów i optymalizację numeryczną. W pracy zajęto się doborem elementów tłumiących. Zaproponowano optymalne ustawienie oraz optymalne wartości współczynników dla układów stabilizujących położenie...
-
Inorganic pollutants deposition in Gdańsk Region in relation to the critical load cencept
PublikacjaBadano depozycję kwaśnych zanieczyszczeń poprzez pomiar stężenia siarczanów, azotanów, azotu amonowego w opadach atmosferycznych zbieranych na terenie stacji monitoringowej w leśnictwie Stara Piła. Wyznaczono depozycję suchą i mokrą. Wyniki uzyskane w okresie od 1994 do 2001 roku porównano z krytycznym ładunkiem dla siarki i azotu określonym dla rejonu gdańskiego.