Filtry
wszystkich: 1174
-
Katalog
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: HIGH-FREQUENCY DESIGN, ELECTROMAGNETIC SIMULATION, SURROGATE MODELING, PERFORMANCE-DRIVEN MODELING
-
Pylon foundation of a cable stayed bridge at the motorway ring road of Wrocław
PublikacjaThe largest bridge of the motorway ring road of Wroclaw is a cable stayed bridge over the Odra river near Rędzin. Due to hydrogeological conditions of the ground it was not convenient to use standard bored piles of high length. Instead shorter piles were applied with additional improvement by cement injections at the pile toes. This decision was possible by extending ground investigation program and application of numerical modeling...
-
Fast geometry scaling of UWB band-notch antennas
PublikacjaImplementation of band-notch capability plays an important role in the design of ultra-wideband (UWB) antennas. At the same time, appropriate sizing of antenna geometry parameters in order to precisely allocate the notch at the required frequency as well as to ensure sufficient reflection level is quite challenging and has to be based—for reliability reasons—on full-wave electromagnetic (EM) simulations of the structure. In this...
-
Decisional DNA based intelligent knowledge model for flexible manufacturing system
PublikacjaModeling an effective mechanism for design and control strategies for the implementation of a flexible manufacturing system (FMS) has been a challenge. Consequently, to overcome this issue various techniques have applied in the past but most of these models are effective only for some specific situation or an element of FMS. In this study, the knowledge representation technique of Decisional DNA (DDNA) is applied to FMS to develop...
-
A gap waveguide-based mechanically reconfigurable phase shifter for high-power Ku-band applications
PublikacjaThis paper presents a novel design of a low-loss, reconfgurable broadband phase shifter based on groove gap waveguide (GGW) technology. The proposed phase shifter consists of a folded GGW and three bends with a few pins forming the GGW and one bend attached to a movable plate. This movable plate allows for adjustments to the folded waveguide length, consequently altering the phase of electromagnetic waves. The advantage of GGW...
-
Justyna Zander dr inż.
Osoby -
Numerical modeling of the combustion in a lab-scale pulverized-coal fired combustion chamber
PublikacjaThis work presents results of numerical modeling of the combustion process inside a lab-scale drop-tube chamber, designed to investigate the slagging properties of the flue ashes, created through the solid fuel firing. Interaction between turbulence and chemistry is accounted by use of probability density function (PDF). FLUENT inputs for non-premixed combustion chemistry modeling are defined. A discrete second phase of the coal...
-
Numerical modeling of the combustion in a lab-scale pulverized-coal fired combustion chamber
PublikacjaThis work presents results of numerical modeling of the combustion process inside a lab-scale drop-tube chamber, designed to investigate the slagging properties of the flue ashes, created through the solid fuel firing. Interaction between turbulence and chemistry is accounted by use of probability density function (PDF). FLUENT inputs for non-premixed combustion chemistry modeling are defined. A discrete second phase of the coal...
-
Modeling of Electrified Transportation Systems Featuring Multiple Vehicles and Complex Power Supply Layout
PublikacjaThe paper proposes a novel approach to modeling electrified transportation systems. The proposed solution reflects the mechanical dynamics of vehicles as well as the distribution and losses of electric supply. Moreover, energy conversion losses between the mechanical and electrical subsystems and their bilateral influences are included. Such a complete model makes it possible to replicate, e.g., the impact of voltage drops on vehicle...
-
Fast EM-driven optimization using variable-fidelity EM models and adjoint sensitivities
PublikacjaA robust and computationally efficient technique for microwave design optimization is presented. Our approach exploits variable-fidelity electromagnetic (EM) simulation models and adjoint sensitivities. The low-fidelity EM model correction is realized by means of space mapping (SM). In the optimization process, the SM parameters are optimized together with the design itself, which allows us to keep the number...
-
Specification-Oriented Automatic Design of Topologically Agnostic Antenna Structure
PublikacjaDesign of antennas for modern applications is a challenging task that combines cognition-driven development of topology intertwined with tuning of its parameters using rigorous numerical optimization. However, the process can be streamlined by neglecting the engineering insight in favor of automatic de-termination of structure geometry. In this work, a specification-oriented design of topologically agnostic antenna is considered....
-
FEA analysis of the multicell piezoelectric motor
PublikacjaThe presented paper concerns a design, modeling and chosen tests of the prototype multicell piezoelectric motor (MPM). The principle of operation based on three independent traveling wave actuators is presented. The main materials and technologies used in the fabrication process are described. The structure of the motor is modeled using static and modal FEM analysis. The process of traveling wave generation in the MPM structure...
-
Do mistakes acceptance foster innovation? Polish and US cross-country study of tacit knowledge sharing in IT
PublikacjaAbstract Purpose – This study aims to understand and compare how the mechanism of innovative processes in the information technology (IT) industry – the most innovative industry worldwide – is shaped in Poland and the USA in terms of tacit knowledge awareness and sharing driven by a culture of knowledge and learning, composed of a learning climate and mistake acceptance. Design/methodology/approach – Study samples were drawn from...
-
Expedited Multi-Objective Design Optimization of Miniaturized Microwave Structures Using Physics-Based Surrogates
PublikacjaIn this paper, a methodology for fast multi-objective design optimization of compact microwave circuits is presented. Our approach exploits an equivalent circuit model of the structure under consideration, corrected through implicit and frequency space mapping, then optimized by a multi-objective evolutionary algorithm. The correction/optimization of the surrogate is iterated by design space confinement and segmentation based on...
-
Introduction to the ONDM 2022 special issue
PublikacjaThis JOCN special issue contains extended versions of selected papers presented at the 26th International Conference on Optical Network Design and Modeling (ONDM 2022), which took place 16–19 May 2022 at Warsaw University of Technology, Warsaw, Poland. The topics covered by the papers represent trends in optical networking research: application of machine learning to network management, cross-layer network performance optimization,...
-
Implicit Space Mapping for Variable-Fidelity EM-Driven Design of Compact Circuits
PublikacjaSpace mapping (SM) belongs to the most successful surrogate-based optimization (SBO) methods in microwave engineering. Among available SM variations, implicit SM (ISM) is particularly attractive due to its simplicity and separation of extractable surrogate model parameters and design variables of the circuit/system at hand. Unlike other SM approaches, ISM exploits a set of preassigned parameters to align the surrogate with the...
-
Interaction Between Storm Water Conduit Flow and Overland Flow for Numerical Modelling of Urban Area Inundation
PublikacjaNowadays we can observe increasing frequency of inundations in cities. This makes accurate predicting of inundations more important than ever. Numerical modeling of this issue requires complex approach with simultaneous calculations of pipe flow and surface flow. In this paper, after a short review of known methods used for solving pipe and surface flow, we will try to answer the question if presented methods would be sufficiently...
-
Three-dimensional conceptual model for service-oriented simulation
Publikacjan this letter, we propose a novel three-dimensional conceptual model for an emerging service-oriented simulation paradigm. The model can be used as a guideline or an analytic means to find the potential and possible future directions of the current simulation frameworks. In particular, the model inspects the crossover between the disciplines of modeling and simulation, service-orientation, and software/systems engineering. Finally,...
-
A Low-Profile 3-D Printable Metastructure for Performance Improvement of Aperture Antennas
PublikacjaIn order to increase the radiation performance of aperture-type antennas, this paper demonstrates a low-profile, planar, single-layer, three-dimensional (3-D) printable metastructure. The proposed hybridized metastructure is highly transparent as it is made out of novel hybrid meta-atoms having transmission coefficient magnitudes greater than -0.72 dB and fully complies with the near-field phase transformation principle. The hybridized...
-
Problemy modelowania liczby podróży generowanych i absorbowanych na przykładzie Gdańska
PublikacjaJedną z podstawowych danych niezbędnych do planowania elementów systemu transportowego jest informacja o liczbie podróży odbywanych na analizowanym obszarze. Dane te uzyskiwane są najczęściej za pomocą symulacyjnych modeli transportowych. Jednym z istotnych elementów i pierwszym etapem najczęściej stosowanego, klasycznego modelu czterostopniowego jest modelowanie liczby podróży generowanych i absorbowanych, podczas którego to...
-
Coplanar Waveguide Fed Ultra-Wideband Antenna Over the Planar and Cylindrical Surfaces
PublikacjaThe investigation of coplanar waveguide fed ultra-wideband antenna and the influence of the proximity of different materials on the reflection coefficients and radiation character-istics is presented. The antenna is composed of two circular coplanar strips which enclose slot aperture of similar shape and is designed on a thin and flexible substrate. From the modeling and experimental tests the antenna shows good performance in...
-
Frequency-Based Regularization for Improved Reliability Optimization of Antenna Structures
PublikacjaThe paper proposes a modified formulation of antenna parameter tuning problem. The main ingredient of the presented approach is a frequency-based regularization. It allows for smoothening the functional landscape of the assumed cost function, defined to encode the prescribed design specifications. The regularization is implemented as a special penalty term complementing the primary objective and enforcing the alignment of the antenna...
-
Ionosphere variability II: Advances in theory and modeling
PublikacjaThis paper aims to provide an overview on recent advances in ionospheric modeling capabilities, with the emphasis in the efforts relevant to electron density variability. The discussion spans a wide range of model formulations (e.g., from purely empirical to physics-based ones and data-driven approaches) seeking for advances or gaps with regard to present challenges. This discussion is further supported by consideration of the...
-
Comparison of state feedback and PID control of pressurizer water level in nuclear power plant
PublikacjaThe pressurizer water level control system in nuclear power plant with pressurized water reactor (PWR) is responsible for coolant mass balance. The main control goal is to stabilize the water level at a reference value and to suppress the effect of time-varying disturbances (e.g. coolant leakage in primary circuit pipeline system). In the process of PWR power plant operation incorrect water level may disturb pressure control or...
-
Hydrodynamic reanalysis of water temperature and salinity in the Baltic Sea using the PM3D model
Dane BadawczeThe dataset contains the results of numerical modeling of water temperature and salinity in the Baltic Sea since 1998. A long-term reanalysis was performed using the three-dimensional hydrodynamic model PM3D (Kowalewski and Kowalewska-Kalkowska, 2017), a new version of the M3D model (Kowalewski, 1997). A numerical dynamic-thermodynamic model of sea...
-
Numerical Solution of the Two-Dimensional Richards Equation Using Alternate Splitting Methods for Dimensional Decomposition
PublikacjaResearch on seepage flow in the vadose zone has largely been driven by engineering and environmental problems affecting many fields of geotechnics, hydrology, and agricultural science. Mathematical modeling of the subsurface flow under unsaturated conditions is an essential part of water resource management and planning. In order to determine such subsurface flow, the two-dimensional (2D) Richards equation can be used. However,...
-
Multi-objective optimization of microwave couplers using corrected domain patching
PublikacjaPractical design of microwave components and circuits is a compromise between various, often conflicting objectives. In case of compact structures, the trade-offs are typically concerned with the circuit size and its electrical performance. Comprehensive information about the best possible trade-offs can be obtained by means of multi-objective optimization. In this paper, we propose a computationally efficient technique for identifying...
-
Performance analysis of data transmission in MC-CDMA radio interface with turbo codes
PublikacjaMulti-carrier code division multiple access (MC-CDMA) technique is a combination of two radio access techniques: CDMA and orthogonal frequency division multiplexing and has the advantages of both techniques. The paper presents the design of transmitter and receiver for MC-CDMA radio interface. It also presents encoders and decoders of turbo codes which were used in simulation of the MC-CDMA technique. Two turbo codes with 8-state...
-
Data set generation at novel test-rig for validation of numerical models for modeling granular flows
PublikacjaSignificant effort has been exerted on developing fast and reliable numerical models for modeling particulate flow; this is challenging owing to the complexity of such flows. To achieve this, reliable and high-quality experimental data are required for model development and validation. This study presents the design of a novel test-rig that allows the visualization and measurement of particle flow patterns during the collision...
-
Ireneusz Kreja dr hab. inż.
OsobyAbsolwent klasy matematycznej I Liceum Ogólnokształcącego w Gdańsku im. Mikołaja Kopernika (1974). Absolwent Wydziału Budownictwa Lądowego Politechniki Gdańskiej (1979). Od 1979 pracuje na PG. W 1989 uzyskał doktorat (z wyróżnieniem), na Wydziale Budownictwa Lądowego, a w 2008 habilitował się (również z wyróżnieniem) na Wydziale Inżynierii Lądowej i Środowiska PG. Od 2011 jest profesorem PG. Na Politechnice Gdańskiej pełnił funkcje:...
-
Hybrid fuzzy-ontological project framework of a team work simulation system
PublikacjaThe aim of this article is to present the project framework for constructing a Software Process Simulation Modeling (SPSM) system. SPSM systems can be used as a virtual environment for the selection of methods and tools of project management in IT support organizations. The constructed system simulates the Scrum methodology, including the management processes and the project roles. For the implementation of Scrum processes, the...
-
Supporting development of the smart ship technology by CFD simulation of ship behavior in close to real operational conditions
PublikacjaThe shipping industry is at the milestone of technological development – autonomous ships. Involving smart technologies accelerates development of green and safe shipping. Also IMO regulations, especially EEDI en-hanced application of new technologies. Meeting economic and ecological requirements future ships need to be designed with respect to increased reliability and operational performance. Design process of ships may be improved...
-
NUMERICAL MODEL OF PLASTIC DESTRUCTION OF THICK STEEL STRUCTURAL ELEMENTS
PublikacjaIn the shipbuilding industry, the risk of brittle fracture of the structure is limited by using certified materials with specified impact strength, determined by the Charpy method (for a given design temperature) and by supervising the welding processes (technology qualification, production supervision, non-destructive testing). For off-shore constructions, classical shipbuilding requirements may not be sufficient. Therefore, the...
-
Modeling an Industrial Revolution: How to Manage Large-Scale, Complex IoT Ecosystems?
PublikacjaAdvancements around the modern digital industry gave birth to a number of closely interrelated concepts: in the age of the Internet of Things (IoT), System of Systems (SoS), Cyber-Physical Systems (CPS), Digital Twins and the fourth industrial revolution, everything revolves around the issue of designing well-understood, sound and secure complex systems while providing maximum flexibility, autonomy and dynamics. The aim of the...
-
Fast tolerance-aware design optimization of miniaturized microstrip couplers using variable-fidelity EM simulations and re-sponse features
PublikacjaManufacturing tolerances and other types of uncertainties may considerably affect operation and performance of microwave components and systems. Quantification of these effects is therefore an important part of the design process. It is even more important to obtain designs whose sensitivity to parameter deviations is reduced as much as possible. All of these require statistical analysis carried out at the level of electromagnetic...
-
Design and Characterization of a Planar Structure Wideband Millimeter-Wave Antenna with Wide Beamwidth for Wearable off-body Communication Applications
PublikacjaThis letter presents the design of a planar single-layer wideband antenna featuring wide beamwidth has well as high and stable in-band gain. The proposed antenna is a planar monopole fed by a bottom-grounded coplanar waveguide to realize wide beamwidth in both the xz- and yz-planes. Simultaneous optimization of all adjustable antenna parameters, carried out at the full-wave electromagnetic simulation level. The constructive interference...
-
Rapid multi-objective design optimisation of compact microwave couplers by means of physics-based surrogates
PublikacjaThe authors introduce a methodology for fast multi-objective design optimisation of miniaturised microwave couplers. The approach exploits the surrogate-based optimisation paradigm with an underlying low-fidelity model constructed from an equivalent circuit of the structure under consideration, corrected through implicit and frequency space mapping. A fast prediction tool obtained this way is subsequently optimised by a multi-objective...
-
Control of the bridge span vibration with high coefficient passive damper. Theoretical consideration and application
PublikacjaThe research was carried out due to the problem of vibration on the lively pedestrian drawbridge across the Motlawa River in the city of Gdansk. In the design stage, the main span of the footbridge showed unfavorable dynamic properties, which may create a comfort problem for pedestrians. The first vertical bending eigenfrequency was recognized as 1.64 Hz. The original design of the footbridge was equipped with a driving cylinder...
-
Residue-Pole Methods for Variability Analysis of S-parameters of Microwave Devices with 3D FEM and Mesh Deformation
PublikacjaThis paper presents a new approach for variability analysis of microwave devices with a high dimension of uncertain parameters. The proposed technique is based on modeling an approximation of system by its poles and residues using several modeling methods, including ordinary kriging, Adaptive Polynomial Chaos (APCE), and Support Vector Machine Regression (SVM). The computational cost is compared with the traditional Monte-Carlo...
-
The linkage between knowledge risk management and organizational performance
PublikacjaThe purpose of this study is to examine the effect of knowledge risk management (KRM) on organizational performance, with measures considered as “softer” measures of performance, i.e. innovativeness, responsiveness, sustainability, and agility. Data were collected using an online questionnaire sent to private and public orga- nizations located all over the world. The analysis and hypotheses testing were performed using structural...
-
Explicit Size-Reduction-Oriented Design of a Compact Microstrip Rat-Race Coupler Using Surrogate-Based Optimization Methods
PublikacjaIn this paper, an explicit size reduction of a compact rat-race coupler implemented in a microstrip technology is considered. The coupler circuit features a simple topology with a densely arranged layout that exploits a combination of high- and low-impedance transmission line sections. All relevant dimensions of the structure are simultaneously optimized in order to explicitly reduce the coupler size while maintaining equal power...
-
Voltage Harmonic Distortion Measurement Issue in Smart-Grid Distribution System
PublikacjaThis paper presents the investigation results ofvoltage harmonic transfer accuracy problems through voltagetransformers which are widely used in power quality monitoringsystems in medium and high voltage grids. A simplified lumpedparameters circuit model of the voltage transformer is presentedand verified by simulation and experimental investigations. Anumber voltage transformers typically used in medium voltagegrid has been tested...
-
Rapid EM-Driven Design of Compact RF Circuits By Means of Nested Space Mapping
PublikacjaA methodology for rapid design of RF circuits constituted by compact microstrip resonant-cells (CMRCs) is presented. Our approach exploits nested space mapping (NSM) technology, where the inner SM layer is used to correct the equivalent circuit model at the CMRC level, whereas the outer layer enhances the coarse model of the entire structure under design. We demonstrate that NSM dramatically improves performance of surrogate-based...
-
SiC-based T-type modules for multi-pulse inverter with coupled inductors
PublikacjaThe paper presents SiC-based three-level T-type modules designed for a high-performance 30kVA DC/AC inverter operating at high frequency 85 kHz with low THD of the output voltage. This inverter system consists of two integrated parts. The first part is active and contains three parallelconnected three-phase T-type modules built with fast-switching SiC power transistors. The second, passive part of the system is a set of inductors...
-
Footbridges. Dynamic Design – Selected Problems
PublikacjaModern footbridges create challenge in esthetic and structural design. Breaking the proven canons is a recipe for architectural success. However esthetic form has to be also a functional pedestrian bridge. Therefore a good FEM modeling is a key element in engineering part of design. The paper presents selected problems related to the modeling of the dynamic construction of footbridges. Several basic dynamic problems concerning...
-
Tacit knowledge influence on intellectual capital and innovativeness in the healthcare sector: A cross-country study of Poland and the US
PublikacjaThis study provides empirical proof that whole organizational innovativeness is rooted in tacit knowledge due to its potency of human capital creation and, that a learning culture composed of a learning climate and mistakes acceptance component fosters human capital development. The main practical implication is that if the IC components are externally rather than internally determined in the particular organization embedded in...
-
Numerical Methods
Kursy OnlineNumerical Methods: for Electronics and Telecommunications students, Master's level, semester 1 Instructor: Michał Rewieński, Piotr Sypek Course description: This course provides an introduction to computational techniques for the simulation and modeling of a broad range of engineering and physical systems. Concepts and methods discussed are widely illustrated by various applications including modeling of integrated circuits,...
-
Techniki zwiększania efektywności metody elementów skończonych poprzez redukcję dziedziny obliczeniowej z wykorzystaniem własności geometrii struktur
PublikacjaWspółczesna elektronika ze względu na swój szybki rozwój wymaga od nas efektywnego modelowania zjawisk polowych. Celem rozprawy jest zwiększanie efektywności metody elementów skończonych poprzez redukcję dziedziny obliczeniowej z wykorzystaniem własności geometrii struktur oraz jej hybrydyzację z użyciem technik analitycznych. Rozprawa zawiera przegląd stanu wiedzy na temat dostępnych obecnie technik modelowania jak również opis...
-
Novel structure and EM-driven design of miniaturized microstrip rat-race coupler
PublikacjaIn this paper, a novel structure and design procedure of a miniaturized microstrip rat-race coupler (RRC) is described. Small size of the RRC is achieved by folding the transmission lines of the conventional circuit into its interior, as well as by implementation of the structure on three layers. The final size of the coupler realized for the operating frequency of 1 GHz is only 220 mm2, which gives over 95% footprint reduction...
-
The conducted EMI in DC-DC converters
PublikacjaThis book presents the phenomena of conducted electromagnetic interference (EMI) generation in DC-DC converters. The measurement and simulation are used to analyze the impact of the most important parameters on the character, level and propagation path of interference. In this book, the analysis of the interference generation and propagation is presented on the example of three basic converters. The wide banded behavior of all...
-
Fire-induced spalling of ultra-high performance concrete: A systematic critical review
PublikacjaUltra-high performance concrete (UHPC) is a novel concrete class characterized by a compressive strength of more than 150 MPa. One of the most significant drawbacks of employing UHPC is that is very low permeability owing to its great compactness of dense structure increases the risk of fire-induced spalling. It is challenging for fire safety and structural engineers to predict and analyze this issue due to the lack of widely accepted...