Wyszukiwarka
Wyniki wyszukiwania dla: FORMALDEHYDE-BASED WOOD ADHESIVES
-
Recent progress in ultra-low formaldehyde emitting adhesive systems and formaldehyde scavengers in wood-based panels: a review
PublikacjaTraditional wood-based panels are produced with synthetic, formaldehyde-based adhesives, commonly made from fossil-derived constituents, such as urea, phenol, melamine, etc. Along with their numerous advantages, such as chemical versatility, high reactivity and excellent adhesive performance, these adhesives are characterized by certain problems, connected with the hazardous volatile organic compounds (VOCs), mostly free formaldehyde...
-
Timber - material of the future. Examples of small wooden architecture structures.
PublikacjaThe aim of this article is to present various types of wood-based products, classified as engineered timber, while specifying the implications of their structural properties for their forms. Timber is used as a construction material due to its fire resistance, good structural characteristics and insulating properties. The advent of new technologies of wood processing and wood-based materials production has converted timber into...
-
Biomedical engineering of polysaccharide-based tissue adhesives: Recent advances and future direction
PublikacjaTissue adhesives have been widely used for preventing wound leaks, sever bleeding, as well as for enhancing drug delivery and biosensing. However, only a few among suggested platforms cover the circumstances required for high-adhesion strength and biocompatibility, without toxicity. Antibacterial properties, controllable degradation, encapsulation capacity, detectability by image-guided procedures and affordable price are also...
-
Influence of Thermal Decomposition of Wood and Wood-Based Materials on the State of the Atmospheric Air. Emissions of Toxic Compounds and Greenhouse Gases
PublikacjaThis paper presents the energy characteristics of wood and wood-based materials in the form of commercially available pellets, furniture board (MDF) and OSB. Toxicometric indices were determined for gaseous destructs arising from thermal decomposition and combustion of the materials studied. The paper proves that combustion conditions are crucial in terms of toxic destructive emissions. It has been shown that the combustion of...
-
Methodology for determination of the selected mechanical properties of wood based on cutting tests
PublikacjaFrom kiln-dried spruce wood (with steam) as well as in natural conditions were randomly selected 8 samples. After determining the average dimensions, moisture content and density of the samples they have been cut on the frame sawing machine PRW15M for measurement of cutting power. Based on those results from a linear rela-tionship of cutting power versus feed per toot mechanical properties of wood such as facture toughness and...
-
Formaldehyde detection with chemical gas sensors based on WO3 nanowires decorated with metal nanoparticles under dark conditions and UV light irradiation
PublikacjaWe report results of formaldehyde gas (CH2O) detection under dark conditions and UV light irradiation with pristine tungsten trioxide nanowires (WO3 NWs) and metal nanoparticles decorated WO3 NWs gas sensing layers. The resistive layers were deposited by one step aerosol assisted chemical vapor deposition (AACVD) on commercial alumina substrates with 10-pair interdigitated platinum electrodes. The elaborated gas sensors, based...
-
Barrett-Joyner-Halenda (BJH) and Brunauer-Emmett-Teller (BET) analysis of wood and straw based biochars
Dane BadawczeThis data set includes the BJH and BET analysis results for straw and wood chips-based biochars generated at 450 Celsius degrees.
-
Conductive Electric Tapes Based on Silicone Pressure-Sensitive Adhesives
Publikacja -
Carboxymethylated polysaccharide-based films as carriers for acrylic pressure-sensitive adhesives
Publikacja -
Monoterpenes emissions from different samples of wood-based materials – laminated chipboards and medium-density fiberboards (MDF)
PublikacjaThe paper presents the results of studies on emission rates of monoterpenes, carried out with the use of a new type of device - Markes’ Micro-Chamber/Thermal Extractor™ (μ-CTE250). Subject of studies were different types of wood-based materials such as: laminated chipboards and medium-density fiberboards (MDF). Based on the results obtained one can conclude that the laminated chipboards may affect the indoor air quality in much...
-
The thermal degradation of acrylic pressure-sensitive adhesives based on butyl acrylate and acrylic acid
Publikacja -
Small-scale passive emission chamber for screening studies on monoterpene emission flux from the surface of wood-based indoor elements
PublikacjaAnalysis of literature data published in the last fewyears leads to the conclusion that in the process of assessment of emission flux of organic compounds emitted from different types of equipment and finishing materials, new types of devices, among which small-scale passive emission chambers for the performance of in-situ research are designed and applied on a larger scale. These devices can be successfully used for the assessment...
-
Influence of Montmorillonite on the Properties of Silicone Pressure-Sensitive Adhesives: Preparation of a Double-Sided Tape Based on the Best Composition
Publikacja -
Design of self-cleaning and self-disinfecting paper-shaped photocatalysts based on wood and eucalyptus derived cellulose fibers modified with gCN/Ag nanoparticles
Publikacja -
Cross-linking of polymer films using phenol-formaldehyde resins with different functional groups
PublikacjaWell-know phenol-formaldehyde resins are used in the production of press-materials, glues, protective coating, mastics. They take a special place among known oligomers because the products based on them are characterized by a low cost and a series of positive properties. Aim of the work: to show the possibility to create polymeric films based on epoxy resins and modified phenol-formaldehyde resins, which contain unsaturated double...
-
Nickel Oxide Thin Film Sensor for Fluctuation-Enhanced Gas Sensing of Formaldehyde
PublikacjaNanocrystalline nickel-oxide-based thin films were prepared by advanced reactive gas deposition, and the response of these films to formaldehyde was studied by fluctuationenhanced sensing. Morphological and structural analyses showed porous deposits of nickel oxide particles with face-centered cubic structure. Resistance fluctuations were measured upon exposure to ethanol, formaldehyde and methane at 200 °C. Power density spectra...
-
Fluctuation-Enhanced Sensing with Organically Functionalized Gold Nanoparticle Gas Sensors Targeting Biomedical Applications
PublikacjaDetection of volatile organic compounds is a useful approach to non-invasive diagnosis of diseases through breath analysis. Our experimental study presents a newly developed prototype gas sensor, based on organically-functionalized gold nanoparticles, and results on formaldehyde detection using fluctuation-enhanced gas sensing. Formaldehyde was easily detected via intense fluctuations of the gas sensor’s resistance, while the cross-influence...
-
Impact of high temperature drying process on beech wood containing tension wood
PublikacjaThe technology of high temperature drying has a great inuence on dimensional and selected physical changes in tension wood. Article is focused on the measurement properties such as moisture content, color changes and longitudinal warping. The quality of beech wood is determined based on structure and properties of wood, frequency of defects in wood material. The tension wood is considered as an important wood defect causing negative...
-
The impact of drying and steaming processes on surface color changes of tension ad normal beech wood
PublikacjaThe aim of the article is to present the influence of high temperature to selected properties of beech wood (Fagus sylvatica L.). The properties such as moisture content, color changes and longitudinal warping were analyzed. The quality of beech wood is determined based on structure and properties of wood, frequency of defects in wood material. The tension wood is considered as an important wood defect causing negative alterations...
-
The Effect of Full-Cell Impregnation of Pine Wood (Pinus sylvestris L.) on Changes in Electrical Resistance and on the Accuracy of Moisture Content Measurement Using Resistance Meters
PublikacjaThe impact of the full-cell impregnation of pine wood was investigated with respect to changes in electrical resistance and the accuracy of moisture content measurement. This study compared the resistance of impregnated and untreated pine timber harvested from the northern part of Poland (Pomeranian region). The wood was impregnated by the vacuum-pressure method. The preservative (TANALITH E 3475) and coloring (TANATONE 3950) agents...
-
The Effect of Wood Provenance and Density on Cutting Forces While Sawing Scots Pine (Pinus sylvestris L.)
PublikacjaSeveral properties of wood including the cutting power requirements can be correlated to wood density. Therefore, according to the literature, the cutting power requirements (and/or cutting forces) could be computed as a function of the wood specific gravity. This research shows that such an approach, based solely on specific gravity, may be considered a rather rough and imperfect estimate of cutting power. Samples of Scots pine...
-
Wood Moisture-Content Measurement Accuracy of Impregnated and Nonimpregnated Wood
PublikacjaThe influence of the impregnation process of pine wood (Pinus sylvestris L.) samples on the electrical resistance changes and the moisture-content measurement accuracy is presented in this paper. In this study, the resistances of impregnated and nonimpregnated green pine timber harvested from northern Poland were compared. An impregnation method based on a vacuum-pressure chamber was used. Copper salts were applied as the impregnated...
-
Synthesis and characterization of biopolyols through biomass liquefaction of wood shavings and their application in the preparation of polyurethane wood composites
PublikacjaThe sustainability of production systems in wood processing, wood industry, and wooden waste disposal is an important issue for European industry and society. Proper development of products based on renewable wood resources gives an opportunity to provide materials with long-term environmental, social, and economic sustainability. This study aims to establish a new way of forestry and agricultural waste materials utilization by...
-
Particulate Matter Production of Small Heat Source Depending on the Bark Content in Wood Pellets
PublikacjaWood pellets as biofuel are more and more used in small heat sources in Europe. Standard wood pellets are produced from wood sawdust without bark. The paper deals about the impact of bark in wood pellets on their properties and combustion process. Special attention in this work is paid to production of particulate matter during combustion of wood pellets depending on bark content. There were experimentally produced spruce wood...
-
Effect of applied standard wood machining fluid on colour and chemical composition of the machined wood surface
PublikacjaAppropriate monitoring of wood machining processes is a key issue to ensure the expected quality of the processed wood, expected efficiency and minimize energy consumption of production processes. A new trend is the design of environmentally friendly machining fluids. In this paper, as a preliminary study in this field, the effect of applied standard wood machining fluid on changes in the colour and chemical composition of the...
-
The effect of beech wood (Fagus sylvatica L.) steaming process on the colour change versus depth of tested wood layer
PublikacjaThe results of experimental research on the colour changes of beech wood at different depths of the tested layer are presented. Beech wood (Fagus sylvatica L.) dried in a conventional kiln was tested. Half of the wood samples were steamed prior to the drying process. Colour changes were measured at various depths after the face milling process was used to remove the material to expose to the deeper surface. The colour changes were...
-
The effect of thermal modification on the quality of the milled surface of beech and pine wood
PublikacjaThe article deals with the effect of thermal modification on the quality of the created surface during milling on CNC milling cutters. The quality of the created surface is evaluated based on surface roughness, specifically its roughness parameter Ra. The observed surface is created by a shank cutter with a diameter of 20 mm and three cutting edges in a spiral at a standard speed of 18,000. min-1. The article compares thermally...
-
Effect of the Drying Method of Pine and Beech Wood on Fracture Toughness and Shear Yield Stress
PublikacjaThe modern wood converting processes consists of several stages and material drying belongs to the most influencing future performances of products. The procedure of drying wood is usually realized between subsequent sawing operations, affecting significantly cutting conditions and general properties of material. An alternative methodology for determination of mechanical properties (fracture toughness and shear yield stress) based...
-
Cutting model parameters from frame sawing of natural and impregnated Scots pine (Pinus sylvestris L.)
PublikacjaIn this paper, absolute and density normalized cutting model parameters of natural and impregnated Scots pine (Pinus sylvestris L.) are shown and a method for the calculation of their corresponding material properties in the principal material directions of wood is presented. The parameters were determined from measurements of cutting power on a sash gang saw, and are in detail the fracture toughness and the shear yield strength...
-
Fluctuation enhanced gas sensing with WO3-based nanoparticle gas sensors modulated by UV light at selected wavelengths
PublikacjaThe sensitivity and selectivity of WO3-based gas sensors can be enhanced by UV-irradiation-induced modulation, especially if different wavelengths are employed. We used fluctuation-enhanced gas sensing, based on measurements of resistance fluctuations in the gas sensor, to study the effects of such modulation on the noise intensity for ambient atmospheres of synthetic air without and with additions of small amounts of ethanol,...
-
Determination of selected chemical parameters in surface water samples collected from the Revelva catchment (Hornsund fjord, Svalbard)
PublikacjaSurface water samples (river and lake) were collected from the Revelva catchment every summer from 2010 to 2013. This study concerns importance of the use of some analytical techniques for pollutants and parameters deter- mination in Arctic environmental samples based on the example of total organic carbon, phenols, and formaldehyde determination and measurement of pH and electrical conductivity parameters. Significant...
-
Sawing Processes as a Way of Determining Fracture Toughness and Shear Yield Stresses of Wood
PublikacjaA new computational model, based on fracture mechanics, was used to determine cutting forces. Unlike traditional computing methods, which depend on many coefficients reflecting the machining of solid wood, the new model uses two main parameters: fracture toughness and shear yield stresses. The aim of this study was to apply this new method to determine these parameters for the tooth cutting edge principal positions and longitudinal...
-
The innovative experimental rig for wood steam drying at atmospheric pressure
PublikacjaThe high cost of fossil fuel and soaring consumer interest have encouraged people in the wood industry to look for faster and more energy-efficient methods to dry lumber. The air-steam mixture as medium of drying process was used in a laboratory kiln especially arranged for that reason. Experimental rig is based on automatic control system. At the time of drying measurements of the internal temperature, wood temperature, moisture...
-
A Method and Device for 3D Recognition of Cutting Edge Micro Geometry
PublikacjaA very useful method was successfully applied in the investigation of tools for machining wood and wood based composites. It allows scanning of the cutting edge micro geometry in three dimensions and reproducing it in a virtual space as a 3D surface. The application of the method opens new possibilities of studying tool wear by scanning, including the calculation of volume loss and other analysis of tool wedge geometry along and...
-
Analyses of Shear Angle in Orthogonal Cutting of Pine Wood
PublikacjaThe determination of energy effects for wood machining processes, such as cutting power and cutting forces, is very useful in designing of manufacture process of wooden products. A more accurate prediction of cutting forces requires a correct determination of the shear angle value, which can be determined using various models. In this article, shear angle values for an orthogonal linear cutting process of pine wood are determined. The...
-
Non-Gaussian Resistance Fluctuations in Gold-Nanoparticle-Based Gas Sensors: An Appraisal of Different Evaluation Techniques
PublikacjaVolatile organic compounds, such as formaldehyde, can be used as biomarkers in human exhaled breath in order to non-invasively detect various diseases, and the same compounds are of much interest also in the context of environmental monitoring and protection. Here, we report on a recently-developed gas sensor, based on surface-functionalized gold nanoparticles, which is able to generate voltage noise with a distinctly non-Gaussian...
-
Distinctive properties of Scots pine (Pinus sylvestris L.) originating from the Carpathian and Great Poland-Pomeranian of Nature and Forest Land
PublikacjaIn this paper values of properties of Scots pine, the fracture toughness and of shear yield stress in the shear zone are presented. Samples of Scotch pine (Pinus sylvestris L.) wood of two provenances from Poland were tested. These properties were determined from the values of cutting power obtained experimentally on the saw frame PRW-15M. The values of fracture toughness and shear yield stress based on the Atkins model for cutting...
-
On the current state of dovetail wall-corner joints in wooden Greek Catholic churches in Polish Subcarpathia with structural and sensitivity analyses
PublikacjaThis paper describes the current condition of some dovetail joints which form the wall corners of two Greek Catholic churches of wooden construction in Polish Subcarpathia. It also gives the historical background of the sacral architecture of that region. The two structures, which represent the same type of log corner joints are situated in Chotylub and Cewków. The buildings were examined e.g. for damage, wood moisture content,...
-
New approaches to cutting resistance estimation of wood cutting process with circular-saw blades
PublikacjaTheoretical and experimental determination of values of cutting resistance belongs to the basic and simultaneously the most developed field of mechanics of this process. Energetic effects of wood sawing process are mainly calculated on the basis of the specific cutting resistance which, in wood cutting, is a function on a lot of factors. In this paper new method for calculation of cutting resistance is described. The latter method...
-
Modelling of heat and mass transfer through wooden buildings
PublikacjaThe aim of this review paper is to examine the most recent available studies dealing with theoretical, numerical and experimental aspects related to modelling of heat and mass transfer through wooden buildings. The main thermophysical, mechanical and hygrometric properties of wood are firstly discussed. Then, the basic governing equations of heat and mass transfer phenomena are presented. A detailed description of the physical...
-
Is It Right To Predict Cutting Forces On The Basis Of Wood Density?
PublikacjaSeveral properties of wood can be correlated to wood density. It is widely accepted that the cutting power requirements are following this general assumption. Therefore, according to classic literature sources available for determination of the cutting power for both band- and circular- sawing machines, the cutting power requirements (and/or cutting forces) are computed as a function of the wood specific gravity SG. It was shown...
-
THE EFFECT OF WOOD DRYING METHOD ON THE GRANULARITY OF SAWDUST OBTAINED DURING THE SAWING PROCESS USING THE FRAME SAWING MACHINE
PublikacjaThe experimental results of the study focused on the effect of drying processes of warm air drying at the temperature of 6580°C and warm air-steam mixture drying at the temperature of 105°C of pine and beech wood to the size of sawdust grains created by cutting using RPW 15M frame saw is presented in the paper. Particle size analysis of dry sawdust was performed using two methods - screening method and optical method based on...
-
Metoda prognozowania mocy skrawania przy przecinaniu piłami polskiego drewna sosnowego z uwzględnieniem wiązkości materiału obrabianego
PublikacjaW pracy zostały przedstawione wartości właściwości materiałowych tj.: wiązkość R oraz naprężenia tnące w strefie skrawania τy, dla drewna sosnowego (Pinus sylvestris L.). Badane próbki drewna pochodziły z czterech Krain Przyrodniczo - Leśnych Polski: Bałtyckiej Krainy Przyrodniczo - Leśnej (kraina A), Karpackiej Krainy Przyrodniczo - Leśnej (kraina B), Małopolskiej Krainy Przyrodniczo - Leśnej (kraina C) oraz Wielkopolsko - Pomorskiej...
-
Praca z drewnem - Przestrzeń eksperymentu w tworzeniu architektury; Crafting Wood - Space of experiment in making architecture
PublikacjaW artykule przedstawiono eksperymenty z materiałem w tworzeniu architektury prowadzące do praktycznych rozwiązań w konstrukcji budynku. Takie podejście do tematyki zastosowania materiałów w architekturze nakreśla praktyczne aspekty tworzenia przestrzeni podczas pracy np. z drewnem. Podejście przedstawiono w kontekście dziedzictwa kulturowego podczas intensywnych warsztatów dotyczących tradycji i kultury budownictwa wybranych regionów...
-
Failure Monitoring and Condition Assessment of Steel-Concrete Adhesive Connection Using Ultrasonic Waves
PublikacjaAdhesive bonding is increasingly being incorporated into civil engineering applications. Recently, the use of structural adhesives in steel-concrete composite systems is of particular interest. The aim of the study is an experimental investigation of the damage assessment of the connection between steel and concrete during mechanical degradation. Nine specimens consisted of a concrete cube and two adhesively bonded steel plates...
-
Non-destructive Testing of Wooden Elements
PublikacjaExamining the condition of wooden elements is crucial from the perspective of proper structure performance. If the deterioration in the internal wood condition, which displays no symptoms visible from the outside, is detected, the further spread of the deterioration can be prevented. Test results often point to the necessity of conducting repairs and, renovations, replacing the structure of wooden beams, or even substituting a...
-
Unprecedented Adhesive Performance of Propylene-Based Hydroxyl Functionalized Terpolymers
PublikacjaThe synthesis of hydroxyl functionalized propylene-based terpolymers and their performance as hot melt adhesives were investigated. The products comprise uniformly distributed butyl and 4-hydroxyl-butyl branches along the polypropylene backbone. Despite the low hydroxyl-functionality level of ≤ 0.5 mol%, hydroxyl functionalized terpolymers show formidable adhesion to aluminum and steel providing an adhesive strength exceeding 16...
-
SHEAR YIELD STRESSES AND FRACTURE TOUGHNESS OF SCOTS PINE (PINUS SYLVESTRIS L.) ACCORDING TO THE RAW MATERIAL PROVENANCE
PublikacjaIn this paper values of the fracture toughness and of shear yield stress in the shear zone of Scots pine are presented. Tests of cutting were carried on samples of Scotch pine (Pinus sylvestris L.) wood of five provenances from Poland. These experimentally cutting tests were carried on the sash gang saw PRW-15M and the values of cutting power were obtained. The values of fracture toughness and shear yield stress based on Atkins’s...
-
Effect of pine impregnation and feed speed on sound level and cutting power in wood sawing
PublikacjaThe sound levels along with the cutting power registered during the sawing process of the impregnated and non-impregnated pine wood at two feed speeds are shown and compared in this paper. Statistically significant differences in the acoustic signals occurred at the lower feed rate. The differences became smaller with an increase in the feed speed. In contrast to the sound signal, the differences...
-
SENSITIVITY ANALYSIS IN THE REHABILITATION OF HISTORIC TIMBER STRUCTURES ON THE EXAMPLES OF GREEK CATHOLIC CHURCHES IN POLISH SUBCARPATHIA
PublikacjaThis work concerns structural and sensitivity analysis of carpentry joints used in historic wooden buildings in south-eastern Poland and western Ukraine. These are primarily sacred buildings and the types of joints characteristic for this region are saddle notch and dovetail joints. Thus, in the study the authors focus on these types of corner log joints. Numerical models of the joints are defined and finite element simulations...