Wyszukiwarka
Filtry
wszystkich: 339
Wyniki wyszukiwania dla: LINEAR BEARING
-
Non-linear model of high damping rubber bearing.
PublikacjaCelem artykułu jest analiza modelu łożyska wykonanego z wysokotłumiącej gumy, które wykorzystywane są do posadowienia konstrukcji budowlanych na terenach sejsmicznych. Model umożliwia numeryczną symulację pracy urządzenia pod zadanym obciążeniem i w danych warunkach termiczno-wilgotnościowych. Wyniki analizy pokazują, iż proponowany model umożliwia symulację zachowania się łożyska w szerokim zakresie odkształceń.
-
Bearing estimation using double frequency reassignment for a linear passive array
PublikacjaThe paper demonstrates the use of frequency reassignment for bearing estimation. For this task, signals derived from a linear equispaced passive array are used. The presented method makes use of Fourier transformation based spatial spectrum estimation. It is further developed through the application of two-dimensional reassignment, which leads to obtaining highly concentrated energy distributions in the joint frequency-angle domain...
-
Improving the accuracy of bearing in active sonar with cylindrical array using spectrum estimation.
PublikacjaThe articles presents a method for improving the accuracy of bearing in multibeam sonar with a cylindrical array. Based on a known spatial spectrum estimation technique, the method has been successfully used in linear array systems. Its accuracy of bearing is satisfactory and ensures a relatively low computational effort. The article discusses certain simplifications and assumptions to adapt the spatial spectrum estimation technique...
-
High-precision bearing estimation for active sonar with cylindrical array performed by interpolated array transformation
PublikacjaThe article presents a method for improving the accuracy of bearing in multibeam sonar with a cylindrical array. The antenna’s non-linear shape and the resulting non-uniform sampling of the signal in space, mean that known methods of high-resolution spectral analysis cannot be used. In order to apply an algorithm from this group, a linear virtual antenna must be produced. The paper presents a technique of mapping a cylindrical...
-
Analysis of sloping brace stiffness influence on stability and load bearing capacity of a truss
PublikacjaThe paper is focused on the numerical study of stability and load bearing capacity of a truss with side elastic braces. The structure is made in reality. The rotational and sliding brace stiffnesses were taken into account. Linear buckling analysis and non-linear static analysis with geometric and material nonlinearity were performed for the beam and shell model of the truss with respect to the angle of sloping braces. As a result...
-
Research on Linear Actuators for Active Foil Bearings
PublikacjaActive foil bearings are a kind of gas foil bearing. They contain actuators which allow for modification of the bearing sleeve size and the shape of the lubrication gap. Rotor vibrations can be actively controlled by these changes. It is possible, among other things, to reduce the starting torque, control the vibration amplitude at different speeds and improve operational safety. Prototypes of active foil bearings are being developed...
-
Highly linear self-assembled porphyrin wires
PublikacjaAn efficient noncovalent assembly process involving high geometrical control was applied to a linear bis(imidazolyl zinc porphyrin) 7Zn, bearing C18 substitutents, to generate linear multiporphyrin wires. The association process is based on imidazole recognition within the cavity of the phenanthroline-strapped zinc porphyrin. In chlorinated solvents, discrete soluble oligomers were obtained after (7Zn)n was end-capped with a terminal...
-
Stability and load bearing capacity of a braced truss under upward wind loading
PublikacjaThe paper is focused on the numerical and experimental investigation of stability of a steel truss under upward wind loading. The structure was stiffened by elastic braces situated at the top and bottom chord. Usually the lateral (translational) brace stiffness is considered. However, the rotational stiffness of braces caused by interaction between torsional stiffness of the truss top chord and bending stiffness of the roof elements...
-
Stability and load bearing capacity of a braced truss under upward wind loading
PublikacjaThe paper is focused on the numerical and experimental investigation of stability of a steel truss under upward wind loading. The structure was stiffened by elastic braces situated at the top and bottom chord. Usually the lateral (translational) brace stiffness is considered. However, the rotational stiffness of braces caused by interaction between torsional stiffness of the truss top chord and bending stiffness of the roof elements...
-
Displacement piles - classification and methods for the calculation of bearing capacity.
PublikacjaDisplacement piles belong to a group of technologies whose main idea is to install or make a pile without extracting ground material. According to definition, contained in PN-EN:1997-1:2008, displacement piles should be considered as driven, pressed in using vibrators and made with the use of spread augers. The classification of piles used so far with regard to the technology of execution is modified. An additional element is the...
-
Pyrrole bearing diazocrowns: Selective chromoionophores for lead(II) optical sensing
PublikacjaDiazocrowns of 18-, 21- and 23-membered rings with pyrrole residue as a part of macrocycle were for the first time used as chromoionophores in lead(II) selective optodes. Sensing properties of optodes depend on the type of macrocycle, namely its size and the type of linker: oligoether or hydrocarbon chain. The best results were obtained for optode bearing 18-membered crown with oligoether linker showing linear response range of...
-
Innovative Cold-formed GEB Section under Bending
PublikacjaThis paper is concerned with the numerical bending capacity study of the innovative cold-formed GEB sections. Both linear buckling analysis and non-linear static analysis incorporating geometric and material nonlinearity were carried out employing a shell structural model. The magnitudes of buckling load and limit load with respect to GEB section depth and thickness were obtained. The opened cold-formed section was tested assuming...
-
Correlation between natural frequencies and buckling load in a stiffened shell
PublikacjaThe paper deals with correlation between natural frequencies and buckling load of a stiffened shell composed of corrugated sheets and vertical stiffeners (columns). The simplified shell segment represents the buckling behaviour of a whole silo with sparsely distributed columns. The paper covers variants of linear buckling anal-yses, dynamic eigenvalue analyses and geometrically non-linear analyses of a segment modelled with shell...
-
ANALYSIS OF BRACE STIFFNESS INFLUENCE ON STABILITY OF THE TRUSS
PublikacjaThe paper is devoted to the numerical and experimental research of stability of a truss with side elastic supports at the top chord. The structure is a model of a real roof truss scaled by factor ¼. The linear buckling analysis and non-linear static analysis were carried out. The buckling length factor for the compressed top chord was calculated and the limit load for the imperfect truss shell model with respect to brace stiffness...
-
Analysis of the influence of geometrical imperfections on the equivalent load stabilizing roof truss with lateral bracing system
PublikacjaThe paper is focused on the numerical analysis of the stability and load bearing capacity of a flat steel truss. The structure was supported by elastic lateral braces. The translational and rotational brace stiffness was taken into account. The linear buckling analysis were performed for the beam and shell model of the truss. The nonlinear static analysis were conducted for the structure initial geometric imperfections. As a result...
-
STABILITY ANALYSIS OF A TRUSS WITH SLOPING ELASTIC BRACES
PublikacjaSteel trusses have a much greater strength and stiffness in their plane than out of their plane, and therefore should be braced against lateral deflection and twisting. Such elements like purlins apart from bearing vertical load are part of bracing that stabilize roof trusses against distortional buckling. The stability of trusses with elastic bracing was investigated in an experimental research. Braces situated at some angle measured...
-
The buckling analysis of a cold-formed steel C-sectional column resting on an elastic foundation
PublikacjaThe paper is focused on stability analysis of different models of steel cold-formed C-section column. The analysed element may be applied as a primary load-bearing member in steel trusses or silo columns. The column can be used as a support for a wall of roof plates made of corrugated sheets. The wall sheeting that restrains the column against buckling may be considered as an elastic foundation. Due to the design solutions the...
-
Application of the Optimization Methods to the Search of Marine Propulsion Shafting Global Equilibrium in Running Condition
PublikacjaFull film hydrodynamic lubrication of marine propulsion shafting journal bearings in running condition is discussed. Considerable computational difficulties in non-linear determining the quasi-static equilibrium of the shafting are highlighted. The approach using two optimization methods (the particle swarm method and the interior point method) in combination with the specially developed relaxation technique is proposed to overcome...
-
Novel Nonlinear High Order Technologies for Damage Diagnosis of Complex Assets
PublikacjaFor the first time worldwide, innovative techniques, generic non-linear higher-order unnormalized cross-correlations of spectral moduli, for the diagnosis of complex assets, are proposed. The normalization of the proposed techniques is based on the absolute central moments, that have been proposed and widely investigated in mathematical works. The existing higher-order, crosscovariances of complex spectral components are not sufficiently...
-
Stability and load bearing capacity of a truss with elastic braces
PublikacjaThe present paper is devoted to the numerical and experimental investigations of stability of a truss stiffened by elastic braces. The model of a real roof truss scaled by factor ¼ was investigated. In the research the linear buckling and non-linear static analysis of the truss shell and beam model with geometric and material non-linearity is presented. The initial imperfections were assumed in the form of the first buckling mode....
-
Smooth least absolute deviation estimators for outlier-proof identification
PublikacjaThe paper proposes to identify the parameters of linear dynamic models based on the original implementation of least absolute deviation estimators. It is known that the object estimation procedures synthesized in the sense of the least sum of absolute prediction errors are particularly resistant to occasional outliers and gaps in the analyzed system data series, while the classical least squares procedure unfortunately becomes...
-
Pile Model Tests Using Strain Gauge Technology
PublikacjaOrdinary pile bearing capacity tests are usually carried out to determine the relationship between load and displacement of pile head. The measurement system required in such tests consists of force transducer and three or four displacement gauges. The whole system is installed at the pile head above the ground level. This approach, however, does not give us complete information about the pile-soil interaction. We can only determine...
-
Vibro piles performance prediction using result of CPT
PublikacjaVibro piles belong to the group of full displacement piles with an expanded base, characterised by a very high load capacity, especially in non-cohesive soils. The problem is to adopt a reliable method for the determination of full load–settlement (Q–s) curve. A frequent difficulty is the determination of the load capacity limit based on the static load test because the course of the load–settlement curve is of a linear nature....
-
The Experimental Determination of Bearings Dynamic Coefficients in a Wide Range of Rotational Speeds, Taking into Account the Resonance and Hydrodynamic Instability
PublikacjaMethods for the experimental determination of dynamic coefficients are commonly used for the analysis of various types of bearings, including hydrodynamic, aerodynamic and foil bearings. There are currently several algorithms that allow estimating bearing dynamic coefficients. Such algorithms usually use various excitation techniques applied to rotor–bearings systems. So far only a small number of scientific publications show how...
-
STABILITY AND LOAD BEARING CAPACITY OF A BARS WITH BUILT UP CROSS SECTION AND ELASTIC SUPPORTS
PublikacjaThe present paper is devoted to the numerical analysis and experimental tests of compressed bars with built–up cross section which are commonly used as a top chord of the roof trusses. The significant impact on carrying capacity for that kind of elements in case of out-of-plane buckling is appropriate choice of battens which are used to provide interaction between separate members. Linear buckling analysis results and nonlinear static...
-
Combined thrust radial bearing of a submarine main shaft – Design and analysis of failure
PublikacjaThis paper presents an analysis of the combined thrust radial bearing of a submarine propulsion shaft. The lubrication system of the bearing is based on a fixed ring. The efficiency of the lubrication system depends on the shaft speed and temperature, which affects oil viscosity. In turn, the thrust bearing load also depends on the rotational speed of the shaft, because as the speed increases, the drag of the ship increases simultaneously,...
-
ASSESSING THE POTENTIAL REPLACEMENT OF MINERAL OIL WITH ENVIRONMENTALLY ACCEPTABLE LUBRICANTS IN A STERN TUBE BEARING: AN EXPERIMENTAL ANALYSIS OF BEARING PERFORMANCE
PublikacjaT his study compares the performance of a plain bearing, with a similar structure to a tail shaft stern bearing, lubricated with either mineral oil or an environmentally acceptable lubricant (EAL). The main characteristic of the bearing is its length/diameter ratio of <1. Measurements are carried out with the bearing operating under loads from 0.5 to 1 MPa and seven speeds ranging from 1 to 11 rev/s. The bearing lubricated...
-
Simulation of large thrust-bearing performance at transient states, warm and cold start-up
PublikacjaThe start-up of a large hydrodynamic thrust bearing of a vertical hydrogenerator is one of the most critical situations during the lifetime of a bearing. Hydrodynamic load capacity is low due to low speed and higher thermal deformations of the pad. A new approach to the simulation of a hydrodynamic bearing is shown in this article. A combination of finite elements method and computational fluid dynamics is used to perform the transient...
-
Experimental research on a hydrodynamic thrust bearing with hydrostatic lift pockets: Influence of lubrication modes on bearing performance
PublikacjaThe aim of the study is to investigate the performance of a thrust bearing equipped with hydrostatic lift pockets under different lubrication modes. Three types of flat land bearing lubrication modes are studied experimentally: hydrostatic lubrication (HS; forced oil injection to the pockets), hybrid lubrication (HS + HD; hydrostatic lubrication combined with the external forced bearing oil supply) and hydrodynamic lubrication...
-
Prediction of Overall In Vitro Microsomal Stability of Drug Candidates Based on Molecular Modeling and Support Vector Machines. Case Study of Novel Arylpiperazines Derivatives
PublikacjaOther than efficacy of interaction with the molecular target, metabolic stability is the primary factor responsible for the failure or success of a compound in the drug development pipeline. The ideal drug candidate should be stable enough to reach its therapeutic site of action. Despite many recent excellent achievements in the field of computational methods supporting drug metabolism studies, a well-recognized procedure to model...
-
Evaluation of the Variability of Vibration Measurement Results in Rolling Bearing Quality Control
PublikacjaThe final result of rolling bearing quality control is influenced by many factors that are not always taken into account. If non-conforming products leave the factory, then the reliability of equipment containing rolling bearings is significantly weakened. The paper presents an analysis of the reasons for the variability of vibration measurement results in rolling bearing quality control. The paper describes the organisation of...
-
Environmentally acceptable lubricants (EAL) compared with a reference mineral oil as marine stern tube bearing lubricant – Experimental and theoretical investigations
PublikacjaThe purpose of this research is to indicate the potential differences in bearing characteristics resulting from the application of different lubricant types with the same viscosity grade. The effect of different environmentally acceptable lubricants (EALs) on hydrodynamic journal bearing properties is studied experimentally and compared to the properties obtained after lubrication with a reference mineral oil. The results of the...
-
A comparative performance assessment of a hydrodynamic journal bearing lubricated with oil and magnetorheological fluid
PublikacjaThis work presents the investigation results of a journal bearing lubricated with magnetorheological fluid that is activated by a local constant magnetic field to vary both the local flow resistance and pressure. The bearing performance is assessed via Finite Element Modelling (FEM) and results are corroborated by experiments. The FEM model uses the Bingham model to describe the fluid film. A dedicated test rig is used to assess...
-
Structural properties of foil bearings: a closed-form solution validated with finite element analysis
PublikacjaFluid film thickness in a compliant foil bearing is greatly influenced by the deflection of the bearing structure. Therefore, in order to properly model performance of a foil bearing, it is mandatory that the deflection of the compliant bearing structure due to the generated hydrodynamic pressure is determined accurately. This article proposes an easy-to-use two-dimensional model, which takes into account detailed geometry of the...
-
Modeling lubricant flow between thrust-bearing pads
PublikacjaInlet temperature is one of the main inputs in all models for the analysis of fluid film bearing performance. At the same time, inlettemperature distribution and also oil velocity distribution at the inlet are the result of flow phenomena in the gap between the bearingpads. These phenomena are complex and in many cases further affected by any special arrangements of forced oil supply to the gapbetween pads. The reason for such...
-
Selected problems of experimental investigation of dynamically loaded journal bearings
PublikacjaIn the paper some problems concerning relations between external bearing loadings and critical lining stresses are described for test stand with rotating load vector. According to the standard ISO 7905/1 this type of test stand, for dynamically loaded slide bearing, is recommended as a basic research unit for material testing in a complete bearing unit. The lining stress calculation results occurred being dependent on applied calculation...
-
Large hydrodynamic thrust bearing: Comparison of the calculations and measurements
PublikacjaHydrodynamic thrust bearings, used to carry axial loads in heavily loaded shafts of water power plants hydro turbines, can reach outer diameters even exceeding 5 m. In such large objects scale effect could be observed. According to this, allowable bearing specific load assuring safe operation of the bearings has to be decreased, which increases thrust bearing dimensions. This effect is caused by excessive thermal deflections of...
-
Experimental investigation into surface texture effect on journal bearings performance
PublikacjaThe aim of this study was to analyse the performance of journal bearings with specially created dimples on the sliding surface and operating under various conditions. The texture was created on the bearing surface that co-acted with the smooth journal; moreover, the variation of the textured surface of the journal mating with the smooth bearing was tested, and the results were compared to those obtained with the standard smooth...
-
Fatigue resistance investigation of the IC engine MB11 bearings, working under conditions of dynamic unidirectional loadings
PublikacjaThe slide bearing material MB11 fatigue resistance has been investigated with the application of SMOK - test stand in which dynamic unidirectional loadings to the test bearing is generated. Slide bearing layer consists of the bronze MB11 ( Cu Pb22 Sn 3 ) sintered to the steel shell. Each of the tested bearing has been subject to the standard 20-hour test, under conditions of the full fluid lubrication. Methodology of the experiments,...
-
Reliability model of slide bearings with particular attention given to lubricating oil
PublikacjaThe paper presents the slide bearing with circulating lubrication as a system of series three-element structure, where lubricating oil is the weakest link. In accordance with the Pierce statement that ''strength of chain is the strength of its weakest link'', a bearing reliability model has been developed. It allows to use the lubricating oil to evaluate the probability of correct working of the whole slide bearing, i.e. the reliability....
-
Acoustic journal bearing – Performance under various load and speed conditions speed conditions
PublikacjaThe paper presents results of experimental testing aiming at finding out what effect system of piezo-electric actuators (PZTs)attached to an aerodynamic journal bearing has on the magnitude of shaft's motion within the bearing operating at specified speed and load. The results clearly demonstrate effectiveness of PZTs in mitigating the shaft's motion thus contributing to the increased stability of the bearing. This stabilizing...
-
Acoustic journal bearing - A search for adequate configuration
PublikacjaClassical non-contact bearings are already used in a number of specialist applications but there are somespecialist areas where they cannot be used for variety of reasons and acoustic sliding bearings could be an alternative. The paper presents the quest for a configuration of an acoustic journal bearing and shows that the overall shape of the bearing and its geometry are of a vital importance for the load capacity oft he bearing....
-
Diagnosis of bearing damage in induction motors by instantaneous power analysis
PublikacjaResearch of the machine with simulated bearing damages has been carried out, where variable load torque, simulating bearing damage, was introduced. The results show that components which can be used for bearings diagnosis appear in the spectrum of the product of current and supply voltage instantaneous values. These components are easier to identify than the components of current spectrum, which have been used so far in diagnostic...
-
Study of the Influence of Heat Convection Coefficient on Predicted Performance of a Large Tilting-Pad Thrust Bearing
PublikacjaPart of the heat generated by the shearing of the lubricating film during operation of a hydrodynamic bearing is transferred to the bearing components. In the case of the pad, which is usually fully submerged in the lubricating oil, heat is further transferred at the pad free walls to the oil by convection. This mechanism causes a thermal gradient in a pad and, consequently, its thermal deflection. In large hydrodynamic thrust...
-
Problems of analytical determination of journal bearing bush fatigue strength estimates
PublikacjaProblems connected with determination of stress distribution in sliding layer of thinwalled bearing bushes, investigated in bearing fatigue test rigs, have been presented. Using an example of plain bearings tested in the fatigue machine SMOK (built at the Gdask University of Technology) problems with obtaining a convergence of iterative procedure for determining the fatigue strength estimators of bearing alloy surface layer are...
-
The influence of polymer bearing material and lubricating grooves layout on wear of journal bearings lubricated with contaminated water
PublikacjaThe goal of the present paper is to investigate wear properties of journal sliding bearing operating in the conditions of contaminated water lubrication. Several bearing materials and bearing sleeve designs (differing in the axial grooves position and their shape) were tested experimentally under typical operating conditions in a dedicated test rig, which was equipped with a lubricating system, enabling lubrication with contaminated...
-
Running performance of an aerodynamic journal bearing with squeeze film effect
PublikacjaResults of theoretical and experimental studies concerning the performance of an aerodynamic journal bearing of which running is assisted by squeeze film ultrasonic levitation (SFUL) are presented in this paper. The SFUL mechanism not only can separate journal from the bearing at the start and stop phases of operation but also can significantly contribute to the dynamic stability of the bearing when it runs at speed. Computer calculations...
-
Application of the fluid–structure interaction technique for the analysis of hydrodynamic lubrication problems.
PublikacjaFluid–structure interaction technique seems to be one of the most promising possibilities for theoretical analysis of lubrication problems. It allows coupling of different physical fields in one computational task, taking into account the interaction between them. In this article, two sets of fluid–structure interaction analyses focusing on the bearing performance evaluation are presented. One analysis was applied to a water-lubricated...
-
New Generation of Water lubricated Foil bearing - Numerical Models and Experimental Verification
PublikacjaIn the paper a new idea of foil water lubricated bearing and methodology of hydrodynamic characteristics calculations is presented. To assesses the theoretical characteristics of these bearings two different computer models were built. First is structural model coupled with fluid model. It takes into account: fluid flow in the deformed fluid gap, specific design of bearing support and friction in bearing support. The second is...
-
Extended duration running and impulse loading characteristics of an acoustic bearing with enhanced geometry
PublikacjaThis paper presents performance during prolonged running of the acoustic bearing when PZTs are switched off and when they are switched on. The effect of active PZT on shaft’s displacements in X and Y directions is clearly demonstrated. Performance of the acoustic bearing was also assessed when an impulse force was applied to the running shaft at speed. Once again the benefits of having PZTs active are beyond doubt. The instability...