Filtry
wszystkich: 2865
wybranych: 2134
-
Katalog
- Publikacje 2134 wyników po odfiltrowaniu
- Czasopisma 97 wyników po odfiltrowaniu
- Konferencje 1 wyników po odfiltrowaniu
- Wydawnictwa 3 wyników po odfiltrowaniu
- Osoby 152 wyników po odfiltrowaniu
- Projekty 3 wyników po odfiltrowaniu
- Kursy Online 44 wyników po odfiltrowaniu
- Wydarzenia 12 wyników po odfiltrowaniu
- Dane Badawcze 419 wyników po odfiltrowaniu
Filtry wybranego katalogu
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: CONTRACT ENGINEER
-
Impact analysis of surface roughness of the plate-plate measuring system on resistance torque in interaction with MR fluid
PublikacjaMagnetorheological (MR) fluids are complex suspensions of magnetic particles in a non-magnetic carrier fluid. They exhibit ‘smart’ properties that enable them to change their rheological parameters in response to a change in the external magnetic field applied. This behavior is used in some engineering solutions, e.g. MR clutches or brakes. For such systems to work correctly, the resistance torque achieved by contact with the...
-
Improvement of subsoil and railway substructure by explosive means.
PublikacjaQuick and effective method of subsoil and railway substructure improvement by using explosive means (registered trade name: microblasting) allowes design and construct railways on lowered bearing soils (i.e. wetlands, marshlands, industrial by-products, municipal wastes, degraded antropogenic embankments). It is usefull and recommendable technology to construct new railways, modernization or maintenance and repairing of old ones...
-
Model of the hydraulic pump powertrain of refuse collection vehicle compaction mechanism
PublikacjaW pracy przedstawiono symulację pracy układu napędowego pompy hydraulicznej mechanizmu prasującego śmieciarki oraz wpływ różnych konfiguracji elementów składowych tego urządzenia na zużycie paliwa silnika napędowego w warunkach przyjętego cyklu obciążenia. W tym celu wykorzystano model układu napędowego pompy hydraulicznej mechanizmu prasującego śmieciarki w formie grafów wiązań oraz wyniki pomiarów ciśnienia roboczego w siłownikach...
-
Analysis of accumulation possibility of energy dissipated in the braking process of train driven by hybrid locomotive
PublikacjaW tradycyjnym procesie hamowania cała energia kinetyczna lub potencjalna pociągu napędzanego lokomotywą z silnikiem spalinowym jest rozpraszana do otoczenia w postaci energii cieplnej. W lokomotywach hybrydowych istnieje możliwość odzyskania części tej energii przez przekazanie jej do akumulatorów i ponowne wykorzystanie do napędu pociągu. W pracy przedstawiono model układu napędowego lokomotywy hybrydowej z silnikiem spalinowym,...
-
Możliwości redukcji przebiegowego zużycia paliwa przy zastosowaniu elektronicznych systemów wspomagających kierowców
PublikacjaElektroniczne systemy wspomagające kierowcę pomagają kierującym kontrolować sytuację na drodze, przekazują sygnały do układu hamulcowego i napędowego, rozpoznają znaki drogowe, pozwalają utrzymać odpowiedni dystans w czasie jazdy w kolumnie, a także kontrolują położenie pojazdu na pasie ruchu. Elek-troniczne systemy wspomagające kierowcę pomagają również zmniejszyć przebiegowe zużycie paliwa, poprzez odpowiednie sterowanie układem...
-
Zagadnienie przenikania fal cieplnych zespołu tłok-pierścienie tłokowe – tuleja cylindryczna (TPC)
PublikacjaNa podstawie zjawisk powodujących zużycie elementów zespołu tłok-pierścienie tłokowe-tuleja cylindryczna zostały wybrane wrażliwe na uszkodzenia cieplne elementy. Następnie została zaproponowana metoda monitorowania zmian maksymalnej amplitudy temperatury warstwy wierzchniej na podstawie której można identyfikować stan techniczny tych elementów. Polega ona na pomiarze głębokości rozchodzenia się fal termicznych za pomocą emisji...
-
Effect of the absence of clear contractual conditions for the pur-chase of combined heat and power systems through public tenders
PublikacjaW artykule przedstawiono dyskusję konsekwencji stosowania różnych podejść do obliczeń kontraktowych parametrów technicznych zespołów kogeneracyjnych. Obliczenia te wykonywane są na potrzeby oferty przygotowywanej w związku z ogłoszeniem przetargu publicznego na zakup siłowni kogeneracyjnej. Brak precyzyjnych zasad określających warunk, i jakie należy przyjąć do wyznaczania parametrów kontraktowych zespołów kogeneracyjnych umożliwia...
-
Diagnosis in the power piston machines
PublikacjaW artykule przedstawiono obecne techniki monitorowania pracy silników i sprężarek dużej mocy. Ze względu na znaczne koszty ewentualnego wyłączenia z ruchu tego typu maszyn są one poddane obserwacji dla przewidywania ewentualnych awarii oraz planowych zatrzymań. Rośnie liczba zaawansowanych systemów pomiarowych z indykowaniem cylindrów. Dawne metody wibroakustyczne zastępowane są pomiarami parametrów procesu termodynamicznego. Słowa...
-
Problemy oszacowania trwałości i niezawodności silników o zapłonie samoczynnym z zastosowaniem teorii procesów semimarkowskich i diagnostyki
PublikacjaW artykule przestawiono znaczenie trwałości i niezawodności silników o zapłonie samoczynnym w eksploatacji systemów technicznych, w których są zastosowane. Wykazano, że do oszacowania trwałości i niezawodności wspomnianych silników bardziej przydatne są modele opracowane w formie semimarkowskiego procesu zmian stanów technicznych tego rodzaju silników w porównaniu do modeli proponowanych w klasycznej teorii niezawodności. Scharakteryzowano...
-
A PROPOSAL OF A DESCRIPTION OF THE OPERATING CONDITIONS OF DIESEL-ELECTRIC LOCOMOTIVES
PublikacjaThe paper presents a proposal of a description of the operating conditions of diesel-electric locomotives. The proposal is a result of the operational experience and the analysis of the locomotive operation. It constitutes a significant simplification in relation to the descriptions currently used by domestic carriers. The paper also presents examples of analyses of the operating conditions of locomotives using the proposed method.
-
Estimation of vehicle operational fuel consumption
PublikacjaW pracy przedstawiono metodę umożliwiającą wyznaczenie referencyjnego zużycia paliwa dla zarejestrowanych warunków eksploatacji. Warunki eksploatacji opisane są rozkładem energochłonności jednostkowej, która obejmuje zarówno wpływ warunków zewnętrznych jak również styl jazdy kierowcy. W pracy przedstawiono zestawienie wyników uzyskanych dla przejazdów wykonanych na terenie Gdańska, w regularnym ruchu miejskim. Przedstawiono także...
-
Problemy sterowania wydajnością pompy cieczy chłodzącej silnik samochodowy z zapłonem iskrowym
PublikacjaW pracy przedstawiono przegląd wybranych pozycji literatury na temat możliwości sterowania chłodzeniem silnika. Parametrem wybranym przez autora do oceny stanu cieplnego silnika jest temperatura ścianki komory spalania. Opisano pomiary tej temperatury jako funkcji wydajności głównej pompy cieczy chłodzącej podczas rozgrzewania silnika.
-
Możliwości zamiany strumieni ciepła odpadowego silników pojazdów na moc efektywną
PublikacjaW pracy przedstawiono przegląd wybranych pozycji literatury na temat możliwości wykorzystania ciepła odprowadzanego od silnika do otoczenia. Wymieniono głównie nowe nie stosowane seryjnie ale obecnie projektowane i badane układy. Wskazano na niekorzystne cechy takie jak duża masa i koszty układów parowych. Termogeneratory z kolei charakteryzują się małą mocą elektryczną na jednostkę masy. W ostatnim rozdziale wspomniano o akumulacji...
-
Dichotomous design of real-time systems
PublikacjaW pracy prezentuje się i analizuje dwie podstawowe metody projektowania komputerowych systemów czasu rzeczywistego, spełniających rozmaite zadania z zakresu automatyki, sterowania, nadzoru i diagnostyki, w których następuje interakcja komputera z obiektami i procesami przemysłowymi, które posiadają naturę ciągłą (pozwalającą na ścisłą matematyczną charakteryzację w czasie ciągłym). Definiuje się podejście uwarunkowane kontekstowo...
-
Numerical analysis of the flow rig for UWS spray examination in exhaust system-relevant conditions
PublikacjaIn the present study, a flow rig with optical access intended for spray investigations in exhaust system-relevant conditions was analysed in terms of flow and temperature in the spray area using numerical simulations. The operation of the rig was examined for a wide range of exhaust mass flow rates, temperatures and various forms of UWS (urea-water solution) spray plumes. The locations of the injector and thermocouple were verified....
-
A conceptual design and numerical analysis of the mixerless urea-SCR system
PublikacjaIn the present study, an innovative design of the urea-selective catalytic reduction (SCR) system without conventional mixing elements was developed. The aim was to obtain a high degree of urea decomposition, and uniform ammonia distribution at the inlet to the catalyst, while minimising the liquid film deposition and keeping the compact design. The concept of the design was based on creating high turbulences and elongating...
-
The conception of exploitation efficiency of autonomic energy systems ofland vehicles and ships = Koncepcja sprawności eksploatacyjnej układów energetycznych autonomicznych pojazdów lądowych i jednostek pływających
PublikacjaW referacie przedstawiono oryginalną koncepcję i możliwości określenia sprawności eksploatacyjnej układów energetycznych pojazdów samochodowych, lokomotyw spalinowych, i jednostek pływających czyli obiektów, które cechuje autonomiczność energetyczna. Sformuowano zasady sytuowania granicy bilansowej układów energetycznych, których zadaniem jest zasilanie odbiorników i grup odbiorników energią mechaniczną, elektryczną i cieplną....
-
The energy test ''100 fishing deys'' of a Baltic cutter
PublikacjaReferat prezentuje oryginalną koncepcję testu energetycznego podczas nieprzerwanej eksploatacji kutra bałtyckiego w przeciągu 100 dni "pracy na łowisku". Test zapewni wyznaczenie na drodze obliczeniowej ilości zużytego paliwa i sprawności eksploatacyjnej układu energetycznego. Podane modele obliczeniowe uwzględniają rzeczywiste rozwiązania układów energetycznych i układów połowowych oraz warunki pracy jednostek a także wartości...
-
Badania zależności między średnimi obciążeniami eksploatacyjnymi silników napędu głównego a nominalną mocą holowania statków towarowych
PublikacjaW referacie zaprezentowano wyniki badań eksploatacyjnych obciążeń silników napędu głównego na 17. statkach towarowych. Jako dane wejściowe wykorzystano zapisy z dzienników maszynowych, na podstawie których wyznaczono parametry eksploatacyjnego rozkładu obciążeń silników głównych w stanie eksploatacji "pływanie swobodne". Uzyskane wyniki umożliwiły wyznaczenie liniowej zależności między średnim obciążeniem silników głównych a mocą...
-
Kompleksowy model nowej generacji układu chłodzenia silnika spalinowego
PublikacjaPrzedstawiono tendencje w konstrukcji układów chłodzenia i dostępne komercyjne metody modelowania pracy układu chłodzenia. Przeprowadzono obliczenia symulacyjne temperatury cieczy komercyjnym programem komputerowym AmeSIM i porównano wyniki z pomiarami wykonanymi na hamowni podwoziowej. Opisano wybrane procesy wymiany ciepła występujące w układach chłodzenia. Przedstawiono ogólny model elementu cieplnego w postaci grafów wiązań...
-
Possibility of defining theoretical operation for diesel mengines in energy terms
PublikacjaPrzedstawiono propozycję wartościowania (ilościowego określenia) działania dowolnego silnika o zapłonie samoczynnym, na przykładzie okrętowego silnika głównego, w którym zachodzą oddziaływania energetyczne w określonym czasie. Działanie to rozumiane jest jako przekazywanie energii śrubie napędowej w ustalonym czasie, w którym zachodzi przetwarzanie i przenoszenie energii w formie pracy bądź ciepła. Wartościowanie działania silników...
-
Gas turbines – technological development and potential use in CAES systems
PublikacjaThis article briefly describes Compressed Air Energy Storage (CAES), focusing on the technological development of one of the key elements of such systems – the gas turbines. It presents the basic parameters and features of gas turbines, as well as turbine classes with example models. Main tendencies in the structural and technological development are discussed. Changes and trends on electric energy markets are becoming more and...
-
Tyre rolling resistance and its influence on fuel consumption
PublikacjaRolling resistance of tyres is one of the major resistive forces acting on any wheeled vehicle. Unfortunately, it is also one of the forces very difficult to measure. It is estimated that in certain traffic conditions (like for example constant speed driving with slow or moderate speed) so called Rolling Resistance Impact Factor may be as high as 0.3. This means that reduction of rolling resistance by 50% would lead to 15% of energy...
-
Signal filtering method of the fast-varying diesel exhaust gas temperature
PublikacjaThe paper presents the problem of the impact of external distortions originating on laboratory test stands on the results of measurements of fast-varying diesel exhaust gas temperature. It has been stressed how significant the aspect of the test stand adaptation is during an experiment to ensure the smallest possible impact. This paper, however, focuses on the methods of mathematical processing of a signal recorded during experimental...
-
The effectivness of fault detection in common rail injectors examination methods
PublikacjaThe article presents the effectiveness tests of fault detection in common rail injectors. 40 injectors with different wear levels were tested. Testing was made on two test benches of a completely different design. Research includes comparison of accuracy, reproducibility and testability to detect specific defects. A device was created for visualization of the fuel injector spraying steam.
-
Analysis of the regenerative braking process for the urban traffic conditions
PublikacjaIn a regular drive system, with an internal combustion engine, vehicle braking is connected with the unproductive dissipation of kinetic and potential energy accumulated in the mass of the vehicle into the environment. This energy can constitute up to 70% of the energy used to drive a vehicle under urban conditions. Its recovery and reuse is one of the basic advantages of hybrid and electric vehicles. Modern traffic management...
-
Comparison of energy efficiency of vehicles powered by different fuels
PublikacjaNajpopularniejsza metoda oceny efektywności energetycznej pojazdów samochodowych polega na porównywaniu przebiegowego zużycia paliwa osiągniętego w warunkach wybranego testu homologacyjnego. Warunki eksploatacji, zdefiniowane za pomocą przebiegów prędkości w czasie, dotyczą najczęściej tylko dwóch kategorii: jazdy miejskiej i pozamiejskiej. Problemy wynikające z takiego sposobu postępowania zostały omówione na przykładzie analizy...
-
Evaluation of the energy efficiency of electric vehicle drivetrains under urban operating conditions
PublikacjaIn electric vehicles, as in hybrids vehicles, a very important factor affecting the energy efficiency of the powertrain is the ability to use the regenerative braking energy. Depending on the settings available in electric vehicles, the driver can choose different modes of operation: switch off the regenerative braking mode altogether, select the intensity of regenerative braking, or leave the control system in automatic mode....
-
INFLUENCE OF DREDGER POWER PLANT TYPE AND DREDGER SIZE ON OUTPUT OF POWER PLANT INSTALLED ON TRAILING SUCTION HOPPER DREDGER
PublikacjaThis paper presents results of investigations dealing with influence of parameters characterizing size of suction hopper dredger as well as type of power system on magnitude of total output of combustion engines installed in dredger power plant.
-
Effect of Nanohydroxyapatite on Silk Fibroin–Chitosan Interactions—Molecular Dynamics Study
PublikacjaFibroin–chitosan composites, especially those containing nanohydroxyapatite, show potential for bone tissue regeneration. The physicochemical properties of these biocomposites depend on the compatibility between their components. In this study, the intermolecular interactions of fibroin and chitosan were analyzed using a molecular dynamics approach. Two types of systems were investigated: one containing acetic acid and the other...
-
Self-assemblies of novel magnesium porphyrins mimicking natural chlorosomal bacteriochlorophylls
PublikacjaSelf-assembling porphyrins are promising materials to mimic natural bacteriochlorophylls c, d, or e encountered in the chlorosomes of photosynthetic bacteria. We have studied four novel magnesium porphyrins mimicking this chlorosomal antenna system. In contrast to previous articles reporting synthetic Zn-porphyrins, our studies focus on porphyrins with Mg as the central atom, which mimic more closely the natural bacteriochlorophylls....
-
Single and Series of Multi-valued Decision Diagrams in Representation of Structure Function
PublikacjaStructure function, which defines dependency of performance of the system on performance of its components, is a key part of system description in reliability analysis. In this paper, we compare two approaches for representation of the structure function. The first one is based on use of a single Multi-valued Decision Diagram (MDD) and the second on use of a series of MDDs. The obtained results indicate that the series of MDDs...
-
Highly linear self-assembled porphyrin wires
PublikacjaAn efficient noncovalent assembly process involving high geometrical control was applied to a linear bis(imidazolyl zinc porphyrin) 7Zn, bearing C18 substitutents, to generate linear multiporphyrin wires. The association process is based on imidazole recognition within the cavity of the phenanthroline-strapped zinc porphyrin. In chlorinated solvents, discrete soluble oligomers were obtained after (7Zn)n was end-capped with a terminal...
-
PROBABILISTYCZNE ASPEKTY ZUŻYCIA SKOJARZEŃ CIERNYCH UKŁADÓW KORBOWO-TŁOKOWYCH NA PRZYKŁADZIE OKRĘTOWYCH SILNIKÓW SPALINOWYCH DWUSUWOWYCH NAPĘDU GŁÓWNEGO
PublikacjaW artykule przestawiono propozycję rozpatrywania zarówno obciążenia jak i zużywania ślizgowych skojarzeń ciernych (łożysk głównych i korbowych) układów korbowo-tłokowych silników spalinowych, zwłaszcza głównych, a także skojarzeń „tłok-tuleja” tych silników, jako procesów stochastycznych. Propozycję tę uzasadniono tym, że deterministyczne podejście do badania zarówno obciążenia jak i zużycia wspomnianych skojarzeń uniemożliwia...
-
Compatibility of Crude Oil Blends─Processing Issues Related to Asphaltene Precipitation, Methods of Instability Prediction─A Review
PublikacjaProcessing crude oil of variable composition, especially due to the need to process crude oil blends obtained from various sources, presents a tremendous process challenge. This is mainly due to the destabilization of the colloidal system manifested mostly by the precipitation of the asphaltene fraction. The precipitation of asphaltenes from crude oil is a serious problem during extraction, transport, and processing. In the latter...
-
Proximal fibular osteotomy as a treatment for degenerative meniscal extrusion
PublikacjaMeniscal extrusion treatment is a key focus area for research and clinical study of degenerative knee pathology. The contact forces between the meniscus and the bones cause external displacements of the meniscus that are resisted by the circumferential fibres. The main risk factors for the excessive deformation of the meniscus are meniscal root tears, disruption of the circumferential fibres, knee malalignment and high body mass...
-
Solubility of carbon dioxide in water: Some useful results for hydrate nucleation
PublikacjaIn this paper, the solubility of carbon dioxide (CO2) in water along the isobar of 400 bar is determined by computer simulations using the well-known TIP4P/Ice force field for water and the TraPPE model for CO2. In particular, the solubility of CO2 in water when in contact with the CO2 liquid phase and the solubility of CO2 in water when in contact with the hydrate have been determined. The solubility of CO2 in a liquid–liquid...
-
Analysis of ring cracks in ceramic rolling elements using the boundary element method
PublikacjaCeramic materials have been increasingly used in bearing technology for over a dozen years. This is due to the characteristic properties of ceramic materials such as: high hardness, corrosion resistance, the possibility of use in aggressive chemical environments, as well as due to the lower specific weight compared to steel materials. However, the use of ceramic materials is connected with many limitations. The main disadvantages...
-
Seismic pounding behavior of multi-story buildings in series considering the effect of infill panels
PublikacjaThe aim of the present paper is to study the influence of the infill panels on the seismic pounding response of adjacent structures in series. The contribution of the masonry infill has been simulated using equivalent diagonal compression struts. Steel frames have been assumed to have elastic-plastic behavior with 1% linear strain hardening. The dynamic contact analysis has been utilized where contact surface model (target and...
-
Optimization of adsorption of methyl orange from aqueous solution by magnetic CoFe2O4/ZnAl-layered double hydroxide composite using response surface methodology
PublikacjaThe CoFe2O4/ZnAl-layered double hydroxide (LDH) composite was successfully developed through a facile co-precipitation method, characterized, and applied as an effective adsorbent for the removal of methyl orange (MO) dye from aqueous solutions. The central composite design (CCD) of the response surface methodology (RSM) was employed to estimate and optimize process variables such as initial MO concentrations, solution pH, adsorbent...
-
Detection of Closing Crack in Beam Based on Responses Induced by Harmonic Excitation
PublikacjaThe non-linear contact model was chosen to simulate the closed crack in the cantilever beam. The study examines the shape and characteristics of the phase diagram of a cantilever beam with closed cracks. It investigates how various crack properties influence the geometry of the phase diagram and proposes a method for identifying cracks based on their features. The area of each closed curve in the phase diagram is determined using...
-
Educational Dataset of Handheld Doppler Blood Flow Recordings
PublikacjaVital signals registration plays a significant role in biomedical engineering and education process. Well acquired data allow future engineers to observe certain physical phenomena as well learn how to correctly process and interpret the data. This dataset was designed for students to learn about Doppler phenomena and to demonstrate correctly and incorrectly acquired signals as well as the basic methods of signal processing. This...
-
Why narrow-kerf technologies are justifiable in modern sawmills?
PublikacjaAnaliza struktury kosztów w tartaku wykazuje, że największy wpływ na ich wartość mają koszty surowca. Przy występującej tendencji kurczenia się zasobów surowca należy dążyć do stosowania w tartakach materiałooszczędnych technologii, w których stosuje się cienkie piły. Przy prawidłowo prowadzonym procesie cięcia zapewniają one redukcję strat materiałowych i korzyści finansowe. Szczególnie wysokie zyski mogą być przy pozyskiwaniu...
-
SMAQ - A Semantic Model for Analitical Queries
PublikacjaWhile the Self-Service Business Intelligence (BI) becomes an important part of organizational BI solutions there is a great need for new tools allowing to construct ad-hoc queries by users with various responsibilities and skills. The paper presents a Semantic Model for Analytical Queries – SMAQ allowing to construct queries by users familiar with business events and terms, but being unaware of database or data warehouse concepts...
-
Marcinkiewicz Averages of Smooth Orthogonal Projections on Sphere
PublikacjaWe construct a single smooth orthogonal projection with desired localization whose average under a group action yields the decomposition of the identity operator. For any full rank lattice \Gamma ⊂ R^d , a smooth projection is localized in a neighborhood of an arbitrary precompact fundamental domain R^d / \Gamma. We also show the existence of a highly localized smooth orthogonal projection, whose Marcinkiewicz average under the...
-
Equitable and semi-equitable coloring of cubic graphs and its application in batch scheduling
PublikacjaIn the paper we consider the problems of equitable and semi-equitable coloring of vertices of cubic graphs. We show that in contrast to the equitable coloring, which is easy, the problem of semi-equitable coloring is NP- complete within a broad spectrum of graph parameters. This affects the complexity of batch scheduling of unit-length jobs with cubic incompatibility graph on three uniform processors to minimize...
-
Miernictwo elektryczne na politechnice w Gdańsku w latach 1904–1945
PublikacjaPolitechnika Gdańska została utworzona w 1904 roku. Działalność uczelni nierozerwalnie związana była z losami Gdańska, dlatego w jej historii do 1945 roku można wyróżnić trzy okresy: pruski, Wolnego Miasta Gdańska oraz czasy drugiej wojny światowej. Od początku, jednym z ważniejszych kierunków nauczania była elektrotechnika. Postęp w elektrotechnice nie był możliwy bez rozwoju miernictwa elektrycznego, dlatego przez cały czas działania...
-
Three Principles for Healthy Living with Light and Lighting
PublikacjaThe lockdown measures applied to cities and towns during the worldwide Covid-19 pandemic have had a widespread impact on people’s lives. Some have found themselves confined to their homes, with limited social contact and a reduced quality of life. Others have found that the lockdown improved their wellbeing, as more time was spent outside, instead of commuting and working in an office building, plus the benefits of spending increased...
-
Assessing Acute Toxicity of Selected Packages Internal Layers Extracts using Microtox®
PublikacjaIn the scientific literature related to the widely understood issue of packaging materials designed to have contact with food (food contact materials), there is much information on raw materials used for their production, as well as their physiochemical properties, types and parameters. Unfortunately, not much attention is given to the issues concerning migration of toxic substances from packaging and its actual influence on the...
-
Evaluation of Langmuir and Freundlich Isotherms for Removal of Cephalexin and Tetracycline Antibiotics By Sistan Sand from Water and Wastewater Samples
PublikacjaIn this research, Sistan sand was used as a natural and inexpensive sorbent for removal of cephalexin and tetracycline antibiotics from water and wastewater samples. For a concentration 60.0 mg L-1 of cephalexin, optimum removal conditions were: pH of the sample 3.0, adsorbent amount 1.0 g, contact time 20.0 min, added amount of sodium chloride to adjust the ionic strength of the solution 7.0 g L-1. Langmuir isotherm was the best...