Wyszukiwarka
Filtry
wszystkich: 748
wybranych: 630
Wyniki wyszukiwania dla: GEOTECHNIA
-
Airstrip Ground Improvement Works by Blasting Charge Technique and Dredged-Ash Material Mixture
PublikacjaSoil improvement by blasting charge technique is known in geotechnics as one of the efficient and inexpensive method. It can be used in preparing of underground to found road construction and buildings as well. The technique proves usefulness especially when dynamic load is applied. It is because of non-stiff or rather resilient type soil after improvement. In noncohesive or organic soil, blasting charge...
-
Centrifuge modelling of tapered wall jacked into dense sand
PublikacjaA series of static penetration tests of trapezoidal walls in dense Fontainebleau sand were performed in the geotechnical centrifuge at Gustave Eiffel University. The models of wall with three different shapes (straight profile with thickness D=16mm, 0.75 degree and 1.5 degree of taper angle) but with the same volume were used. The soil mass was instrumented with five stress cells located at two levels at 2D, 4D and 6D distance...
-
SHORT REVIEW AND 3-D FEM ANALYSIS OF BASIC TYPES OF FOUNDATION FOR OFFSHORE WIND TURBINES
PublikacjaSome problems of the foundations of offshore wind turbines are considered in this paper. A short review is presented on the two basic types of foundations, i.e. monopiles and gravity foundations, including their basic features and applications as well as general design considerations. Also, some issues regarding analysis are discussed, including geotechnical problems and modelling techniques. A numerical model of offshores turbine...
-
Applications of permeability, oedometer and direct shear tests to the sand mixed with waste tire crumb
PublikacjaThe amount of the used waste rubbers in the world has been increasing every year, and their utilization, become a major environmental problem worldwide. The present experimental work has been performed to investigate the influence of rubber inclusion on the behavior of a sand. Geotechnical properties of the sand, and sand with tire crumb at various ratios mixtures (0%, 2.5%, 7.5%, and 15%) were investigated through a series of...
-
Technical monitoring system for a new part of Gdańsk Deepwater Container Terminal
PublikacjaDevelopment strategy for the port of Gdańsk assumes that , up to 2027, it will become the main transport centre in the Baltic Sea region. To this end , for many years work has been carried out to facilitate access to the port both by sea and land. One of the elements of extension of the port is the building of another terminal of Deepwater Container Terminal , Gdańsk. In this task, geotechnical operations aimed at appropriate...
-
Stan przedawaryjny wykopu głębokiego w obudowie z pali CFA
PublikacjaW artykule przedstawiono stan przedawaryjny wykopu głębokiego w obudowie z pali CFA. Omówiono warunki geotechniczne podłoża oraz rozwiązania projektowe. Przeprowadzono analizę dwóch wersji projektów konstrukcyjnych oraz fazę wykonawstwa z wskazaniem na liczne błędy. Przedstawiono możliwe oraz przyjęte działania naprawcze. Omówiono problemy i błędy projektowe na etapie działań naprawczych. Wskazano przyczyny wystąpienia stanu przedawaryjnego.
-
Hybrydowa technologia wzmacniania gruntu w renowacji wałów przeciwpowodziowych
PublikacjaW artykule przedstawiono propozycję kompleksowego podejścia do renowacji wałów przeciwpowodziowych z zastosowaniem tzw. technologii hybrydowych. Autorzy prezentują technologię, opracowaną z udziałem Katedry Geotechniki, Geologii i Budownictwa Morskiego Politechniki Gdańskiej, łączącą znane metody dynamicznego wzmacniania podłoża gruntowego. Technologia, w swej hybrydowej formule, zapewnia odpowiednie wzmocnienie podłoża zalegającego...
-
Hydraulic conductivity of a biopolymer treated sand
PublikacjaThis paper presents results of laboratory assessment of creating seepage barriers in a sandy soil using biopolymer additives (bio substance), which consist of polysaccharides and water. Polysaccharides strongly interact with water to produce a viscous suspension. The aim of the conducted work was to investigate the influence of a biosubstance employed in a highly permeable sandy soil. The amount of the biopolymer used in a sample...
-
Brief Literature Review and Classification System of Reliability Methods for Evaluating the Stability of Earth Slopes
PublikacjaThe issue of slope stability is one of the most important and yet most difficult geotechnical problems. Assessing slope stability is particularly difficult because of the many uncertainties involved in the process. To take these uncertainties into account, probabilistic methods are used, and the reliability approach is adopted. There are many methods for reliability assessment of earth slope stability. However, there is no system...
-
Some geomechanical properties of a biopolymer treated medium sand
PublikacjaSome geomechanical properties of a biopolymer treated medium sand. This paper presents a laboratory assessment of geomechanical properties of sandy soil improved by biopolymer application. Additives (biosubstance) consist of polysaccharides and water. Biosubstance used in the project was xanthan gum, which comes from bacteria Xanthomonas campestris. Triaxial shear compression tests and unconfi ned compression tests were carried...
-
Badanie modułu odkształcenia podłoża gruntowego w nasypie kontrolowanym za pomocą płyty statycznej i lekkiej płyty dynamicznej
PublikacjaW praktyce inżynierskiej, zarówno projektowej, jak i wykonawczej, niewątpliwie przydatne są korelacje między parametrami geotechnicznymi. Artykuł przedstawia polowe badania porównawcze lekką płytą dynamiczną (LFWD) oraz płytą statyczną (VSS), wraz określeniem zależności korelacyjnych pomiędzy modułem odkształcenia podłoża wyznaczonym za pomocą lekkiej płyty dynamicznej EVd oraz pierwotnym i wtórnym modułem odkształcenia EV1, EV2....
-
THE APPLICATION OF KALMAN FILTERING TO PREDICT VERTICAL RAIL AXIS DISPLACEMENTS OF THE OVERHEAD CRANE BEING A COMPONENT OF SEAPORT TRANSPORT STRUCTURE
PublikacjaAs the devices designed to transport materials, the overhead cranes should meet certain geometric requirements for their operation to be safe. The presently available geodetic equipment, in particular total stations, provides opportunities for precise 3D measurements of coordinates of the controlled points. These coordinates make a basis for correcting the height of crane runway axes. The paper presents a method to calculate position...
-
Modelling tunnelling-induced deformation in stiff soils with a hyperelastic–plastic anisotropic model
PublikacjaIn this paper, the tunnelling-induced deformation in anisotropic stiff soils is analysed using FE modelling. The influence of material description is investigated rather than an advanced simulation of the tunnelling method. A new hyperelastic– plastic model is proposed to describe the anisotropic mechanical behaviour of stiff highly overconsolidated soil. This model can reproduce the superposition of variable stress-induced anisotropy...
-
The high-cyclic model for sand tested beyond the usual ranges of application
Publikacja -
Influence of initial density of cohesionless soil on evolution of passive earth pressure
PublikacjaArtykuł porusza problem odporu bezkohezyjnego gruntu. Obliczenia wykonano wykorzystując metodę elementów skończonych na bazie mikropolarnego prawa hipolastycznego. W obliczeniach przyjęto różne początkowe zagęszczenia oraz średnice cząstek gruntu.
-
An experimental investigation of the influence of plasticity on creep degradation rate
Publikacja -
Experimental insights into consolidation rates during one-dimensional loading with special reference to excess pore water pressure
Publikacja -
A hyperelastic model for soils with stress-induced and inherent anisotropy
PublikacjaIn this paper, modelling of the superposition of stress-induced and inherent anisotropy of soil small strain stiffness is8presented in the framework of hyperelasticity. A simple hyperelastic model, capable of reproducing variable stress-induced9anisotropy of stiffness, is extended by replacement of the stress invariant with mixed stress–microstructure invariant to10introduce constant inherent cross-anisotropic component. A convenient...
-
An experimental investigation of the influence of plasticity on creep degradation rate
Publikacja -
Experimental observations on the creep behaviour of frozen soil
PublikacjaConstitutive models in the literature for creep of frozen soil are based on the direct use of time counted from the onset of creep. An explicit time dependence in a constitutive equation violates the principles of rational mechanics. No change in stress or temperature is allowed for during creep, using the time-based formulations. Moreover, the existing descriptions need much verification and improvement on the experimental side...
-
A novel DEM-based pore-scale thermal-hydro-mechanical model for fractured non-saturated porous materials
PublikacjaDo propagacji pęknięć wykorzystano nowy oparty na DEM, termiczno-hydromechaniczny model dwufazowego przepływu płynu w skali porów rozszerzony o wymianę ciepła w nienasyconych materiałach porowatych o małej porowatości. Wykonano obliczenia numeryczne dla kohezyjnych próbek ziarnistych przy użyciu DEM w pełni sprzężonego z CFD (opartego na sieci przepływu płynu) i wymianą ciepła, który zintegrował mechanikę dyskretną z mechaniką...
-
Finite element study of patterns of shear zones in granular bodies during plane strain compression
PublikacjaW artykule przedstawiono obliczenia efektów skali na nośność fundamentu na piasku. Obliczenia wykonano przy pomocy mikropolarnego prawa hipoplastycznego. W obliczeniach wykorzystano stochastyczne rozkłady początkowego wskaźnika porowatości według rozkładu Gaussa.
-
3D DEM simulations of monotonic interface behaviour between cohesionless sand and rigid wall of different roughness
PublikacjaArtykuł omawia wyniki metodą elementów dyskretnych (DEM) dotyczace zachowania się strefy kontaktu między bezkohezyjnym piaskiem a sztywną scianą o różnej szorstkości. Obliczenia wykonano dla dla różnej wysokości, nachylenia i rozstawu rowków wzdłuż sciany, które symulowały jej szorstkość. W symulacjach zmieniano dodatkowo ciśnienie pionowe i początkowy wskaźnik porowatosci piasku. Nacisk położono na wpływ szorstkości na mobilizowany...
-
Comparative 3D DEM simulations of sand–structure interfaces with similarly shaped clumps versus spheres with contact moments.
PublikacjaThree-dimensional simulations of a monotonic quasi-static interface behaviour between initially dense cohesionless sand and a rigid wall of different roughness during tests in a parallelly guided direct shear test under constant normal stress are presented. Numerical modelling was carried out by the discrete element method (DEM) using clumps in the form of convex non-symmetric irregularly shaped grains. The clumps had an aspect...
-
Simulations of hydro-fracking in rock mass at meso-scale using fully coupled DEM/CFD approach
PublikacjaThe paper deals with two-dimensional (2D) numerical modelling of hydro-fracking (hydraulic fracturing) in rocks at the meso-scale. A numerical model was developed to characterize the properties of fluid-driven fractures in rocks by combining the discrete element method (DEM) with computational fluid dynamics (CFD). The mechanical behaviour of the rock matrix was simulated with DEM and the behaviour of the fracturing fluid flow...
-
Impact of spraying commercial Bentonite Nanoclay on fortification of the mortar as Nano Sprying Technique (NST) in heritages and historical buildings
PublikacjaSpraying Bentonite NanoClay as an innovative idea satisfied an urgent need for conservation of historical brick constructions. This research explores the application of Nanotechnology as a Nano-Geotechnics (NaG) and Nano Ground Improvement (NGI) techniques for fortifying the mortar between bricks in historical buildings against some environmental erosive factors. Bentonite Nanoparticles were selected because of their compatibility...
-
Bearing capacity of monotonically installed tapered piles in medium dense Fontainebleau sand
PublikacjaA series of installation of tapered piles in medium-dense Fontainebleau sand were performed in the geotechnical centrifuge at Gustave Eiffel University. The models of piles with three different shapes - straight profile (S), and with taper angle of 0.70 degrees (T1), and 1.4 degrees (T2) were used. The piles were instrumented with fiber optic wires on the shaft and load cell at the base. After monotonic installation, the models were...
-
Numerical Solution of the Two-Dimensional Richards Equation Using Alternate Splitting Methods for Dimensional Decomposition
PublikacjaResearch on seepage flow in the vadose zone has largely been driven by engineering and environmental problems affecting many fields of geotechnics, hydrology, and agricultural science. Mathematical modeling of the subsurface flow under unsaturated conditions is an essential part of water resource management and planning. In order to determine such subsurface flow, the two-dimensional (2D) Richards equation can be used. However,...
-
Soil improvement by short stone columns.
PublikacjaW artykule przedstawiono sposób dogęszczania podłoża gruntowego wykorzystywany do renowacji istniejących nawierzchni placów składowych i dróg. Proponowany sposób polega na formowaniu w gruncie kolumny o niewielkiej średnicy. Kolumnę tą formuje się poprzez wbijanie w rozluźnione podłoże trzpienia stalowego, z jednoczesnym dosypywaniem gruntu.Sposób ten stosuje się przede wszystkim jako metodę wzmocnienia podłoża pod nawierzchniami...
-
Permeability of sandy soils estimated from particle size distribution and field measurements
PublikacjaAccurate estimation of soil permeability is crucial in many geotechnical applications. Empirical and theoretical equations based on soil particle size distribution (PSD) offer a fast and cheap way for preliminary estimation of permeability in granular soils, however the results obtained from various formulas available in the literature often show significant discrepancies. While several comparative studies on this topic have been...
-
The Effect of the Selection of Three-Dimensional Random Numerical Soil Models on Strip Foundation Settlements
PublikacjaThis paper delivers a probabilistic attempt to prove that the selection of a random three-dimensional finite element (FE) model of a subsoil affects the computed settlements. Parametricanalysis of a random soil block is conducted, assuming a variable subsoil Young’s modulus inparticular finite elements. The modulus is represented by a random field or different-sized setsof random variables; in both cases, the same truncated...
-
Stability Assessment of Coastal Cliffs Incorporating Laser Scanning Technology and a Numerical Analysis
PublikacjaWe investigated the cli coast in Jastrzebia Gora, Poland. The measurements that were taken between 2014 and 2018 by applying terrestrial, mobile, and airborne laser scanning describe a huge geometric modification involving dislocations in a 2.5 m range. Dierential maps and a volumetric change analysis made it possible to identify the most deformed cli’s location. Part of the monitoring of coastal change involved the measurement...
-
Likwidacja suchego doku przy Nabrzeżu Przemysłowym w Porcie Gdańsk
PublikacjaW niniejszej pracy przedstawiono problemy techniczne związane z likwidacją dużego obiektu hydrotechnicznego, stanowiącego utrudnienie nawigacyjne w intensywnie eksploatowanym portowym kanale dostępowym w Porcie Gdańsk. Dwukomorowy dok zlokalizowany przy Nabrzeżu Przemysłowym wybudowano w latach 1970-1972. Komory dokowe służyły do budowy żelbetowych, pływających skrzyń falochronowych, na potrzeby budowanego w tym czasie Portu Północnego....
-
INFLUENCE OF TIME ON THE BEARING CAPACITY OF PRECAST PILES
PublikacjaOne of the most popular types of foundations in layered subsoil with very differentiated soil shear strengths are precast piles. One of the reasons is a fact that we can well control the driving process during the installation of these piles. The principles of the assessment of bearing capacity and settlements of the piles given by Eurocode 7, concentrate on two main methods, i.e. Static Pile Load Tests (SPLT) and Dynamic Driving...
-
Simulation of reactive materials in column and reservoir tests. Sensitivity analysis for a linear coupled model
Publikacja -
Visualization and quantification of lab vibratory compacting process for aggregate base materials using accelerometer
Publikacja -
Field investigation and numerical analysis of an inverted pavement system in Tennessee, USA
Publikacja -
Structured deformation of granular material in the state of active earth pressure
PublikacjaThe paper focuses on the ability of granular materials to undergo structured deformation by analysing the data from the retaining wall model tests and discrete element simulations. The structured deformation means the movement of a granular material which produces a stable, regular pattern of multiple shear bands. The paper's primary purpose is to study this kind of deformation for the selected data representing the state of active...
-
Effect of fluctuation of current void ratio on the shear zone formation in granular bodies within micro-polar hypoplasticity
PublikacjaW artykule przedstawiono wyniki numerycznej analizy wpływu fluktuacji wskaźnika porowatości w materiałach granulowanych na powstawanie lokalizacji odkształceń. Obliczenia wykonano dla ściskania dwuosiowego stosując metodę elementów skończonych na bazie mikropolarnego prawa hipoplastycznego
-
Micro-modelling of shear localization during quasi-static confined granular flow in silos using DEM
PublikacjaThe paper deals with the quasi-static confined flow of cohesionless sand in a plane strain model silo with parallel walls and a slowly movable bottom. Numerical modelling was carried out by the discrete element method (DEM) using spheres with contact moments to approximately capture a non-uniform shape of sand particles. Different initial void ratios of sand and silo wall roughness grades were employed. Regular triangular grooves...
-
Coupled DEM/CFD analysis of impact of free water on the static and dynamic response of concrete in tension regime
PublikacjaW tym artykule zbadano numerycznie quasi-statyczne i dynamiczne zachowanie częściowo nasyconego płynem betonu w warunkach dwuwymiarowego (2D) jednoosiowego rozciągania w mezoskali. Obliczono, jaki wpływ ma zawartość wolnego płynu porowego (gazu i wody) na proces pękania i wytrzymałość betonu w rozciąganiu. Do symulacji zachowania betonu całkowicie i częściowo nasyconego płynem w warunkach quasi-statycznych i dynamicznych wykorzystano...
-
FE-modeling of shear resistance degradation in granular materials during cyclic shearing under CNS condition
PublikacjaW artykule przedstawiono wyniki numerycznej analizy degradacji wytrzymałości na ścinanie w materiałach granulowanych podczas cyklicznego ścinania z warunkiem stałej sztywności normalnej. Obliczenia wykonano przy zastosowaniu metody elementów skończonych i mikropolarnego modelu hipoplastycznego.
-
Consolidation analysis of clayey soils using analytical tools
Publikacja -
FEM modelling of screw displacement pile interaction with subsoil
PublikacjaPredicting the-settlement characteristics of piles is an important element in the designing of pile foundations. The most reliable method in evaluating pile-soil interaction is the static load test, preferably performed with instrumentation for measuring shaft and pile base resistances. This, however, is a mostly post-implementation test. In the design phase, prediction methods are needed, in which numerical simulations play an...
-
Influence of the grains shape on the mechanical behavior of granular materials
PublikacjaDiscrete Element Method is a numerical method suitable for modeling geotechnical problems concerning granular media. In most cases simple forms of grains, like discs or spheres, are used. But these shapes are capable of soil behavior modeling up to a certain point only, they cannot reflect all of the features of the medium (large shear resistance and large volumetric change). In order to reflect the complex behavior of the real...
-
Numerical Modelling for Prediction of Compression Index from Soil Index Properties in Jimma town, Ethiopia
PublikacjaIn this study, correlations are developed to predict compression index (Cc) from index parameters so that one can be able to model Jimma soils with compression index using simple laboratory tests. Undisturbed and disturbed soil samples from twelve different locations in Jimma town were collected. Laboratory tests like specific gravity, grain size analysis, Atterberg limit, and one-dimensional consolidation test for a total of twenty-four...
-
Micro- and nano-Illite to improve strength of untreated-soil as a nano soil-improvement (NSI) technique
PublikacjaSoil stabilization is a technique of improving the geotechnical properties of soils for various engineering applications. However, conventional stabilizers such as cement and lime have some limitations, such as high cost, environmental impact, and durability issues. Therefore, there is a need for alternative and innovative stabilizers that can overcome these challenges. This study introduces nano-Illite, a type of clay mineral,...
-
The effect of fishing basin construction on the behaviour of a footbrdge over the port channel
PublikacjaThe paper analyses possible causes of failure of the rotating footbridge over the Ustka port channel. In July, 2015, strange behaviour of this object was observed in the form of excessive vibrations of bridge platform suspension rods, with the accompanying acoustic effects. A preliminary geotechnical analysis has revealed that this destructive effect was caused by the nearby construction works, namely construction of a fishing...
-
Theoretical assessment of fabric and permeability changes in clays affected by organic contaminants
Publikacja -
Effectiveness of Random Field Approach in Serviceability Limit State Analysis of Strip Foundation
PublikacjaThis work conducts a probabilistic inquiry on how the variability of the parameter defining soil deformability affects the settlement of the foundation located on the soil. The analysis addresses the random foundation model to relevantly estimate the probability of allowable deflection exceedance. The constitutive model parameter is based either on a single random variable or a random field. The computations incorporate direct...