Filtry
wszystkich: 2569
-
Katalog
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: counting error
-
Approximate Cramér–Rao bound on Doppler error in correlation-processing relatively narrowband noise radar
PublikacjaThe paper studies limitations on accuracy of Doppler estimation in continuous-wave noise radar with correlation processing. Second order properties of output of the correlation receiver are evaluated and an approximate Cram´er-Rao bound on errors of Doppler measurement is derived. The accuracy of Doppler measurements is found to be affected by the following factors: power spectral density of noise signal, frequency response of the...
-
Bearing errors passive sonar stationary target location
PublikacjaPrzedstawiono metodę wyznaczania współrzędnych nieruchomego celu na podstawie namiarów wykonywanych w sonarze pasywnym. Określono wymagania odnośnie ruchu sonaru, przy których błędy wyznaczania współrzędnych są minimalne. Podano zależności umożliwiające analityczne wyznaczanie błędów współrzędnych. Poprawność wyników analizy potwierdzono eksperymentami numerycznymi.
-
Effects of workpiece feeding errors on multi-rip saws
PublikacjaW pracy przedstawiono przyczyny i efekty błędów prowadzenia materiału na wielopiłach tarczowych. Ich znajomość umożliwia szybką diagnostykę przyczyn, a także skuteczną minimalizację błędów prowadzenia materiału.
-
Balance errors in numerical solutions of shallow water equations
PublikacjaThe analysis of the conservative properties of the shallow water equations is presented in the paper. The work focuses on the consistency of numerical solution of these equations with the conservation laws of mass and momentum. The investigations involve two different conservative forms which are solved by an implicit box scheme. The theoretical analysis supported by numerical experiments is carried out for rectangular channel...
-
Errors caused by microwave part of the microwave heating system
PublikacjaPrzedstawiono skrótowo zasadę pracy i konstrukcję systemu do badań naukowych procesów grzania mikrofalowego. Wyprowadzono wyrażenie opisujące wartość średniokwadratową błędu pomiaru energii mikrofalowej i przeanalizowano składowe błędu pomiaru powodowane przez rzeczywiście występujące w układzie pomiarowym parametry techniczne jego części mikrofalowej.
-
P-674 Automatizing ovarian follicle counting and measurement with artificial intelligence
Publikacja -
Application of virtual gate for counting people participating in large public events
PublikacjaThe concept and practical application of the developed algorithm forpeople counting in crowded scene is presented. The aim of the work is to estimatethe number of people passing towards entrances of a large sport hall. Thedetails of implemented the Virtual Gate algorithm are presented. The video signalfrom the camera installed in the building constituted the input for the algorithm.The most challenging problem was the unpredicted...
-
Accounting
Czasopisma -
Minimum mean square error estimation of speech short-term predictor parameters under noisy conditions
Publikacja -
Correcting a widespread error: Neuroprotectant N-acetyl-L-tryptophan does not bind to the neurokinin-1 receptor
Publikacja -
Reliable OFDM Data Transmission with Pilot Tones and Error-Correction Coding in Shallow Underwater Acoustic Channel
PublikacjaThe performance of Underwater Acoustic Communication (UAC) systems are strongly related to the specific propagation conditions of the underwater channel. Horizontal, shallow-water channels are characterised by extremely disadvantageous transmission properties, due to strong multipath propagation and refraction phenomena. The paper presents the results of communication tests performed during a shallow, inland-water experiment with...
-
Utilization of a Non-Linear Error Function in a Positioning Algorithm for Distance Measurement Systems Designed for Indoor Environments
PublikacjaA new positioning algorithm for distance measurement systems is outlined herein. This algorithm utilizes a non-linear error function which allows us to improve the positioning accuracy in highly difficult indoor environments. The non-linear error function also allows us to adjust the performance of the algorithm to the particular environmental conditions. The well-known positioning algorithms have limitations, mentioned by their...
-
The effect of improved cutting conditions of the circular saw blade on precision of cutting
PublikacjaW pracy przedstawiono analizę i wyniki badań doświadczalnych dokładności przecinania na dwuwrzecionowej pilarce tarczowej. W warunkach przemysłowych badano piły starej (typ "Multix") i nowej konstrukcji podczas przecinania pryzm ze zmrożonego drewna brzozowego. Ponadto, określono wpływ kinematyki układu przecinania na uzyskiwaną dokładność przecinania.
-
Quality of Analytical Results: Classifiying Errors and Estimating Measurement Uncertainty
Publikacja -
Errors analysis of differential single-frequency geo-positioning algorithm
Publikacja -
Analysis of Measurement Errors in Rail Vehicles’ Pantograph Inspection System
PublikacjaThe paper presents an approach to evaluation of height measurement errors in laser scanning inspection system. The system, consisting of a laser line generator and a specialized camera, is dedicated to diagnosing carbon contact strips of railway vehicles’ pantographs. While height measurement resolution is easily computable based on system parameters, determining the measurement error is troublesome due to numerous impacts. As...
-
Errors of a Linear Current Approximation in High-Speed PMSM Drives
PublikacjaCurrent sampling techniques and predictive algorithms used in the digital control of electric drives rely on a simple mathematical model that assumes linear current changes upon constant supplying voltages. This paper identifies rotor movement as a factor that makes this assumption invalid when the rotor covers an angular distance of a few tens of degrees during the control interval duration. The errors of the linear current approximation...
-
Quality of Analytical Results: Classifiying Errors and Estimating Measurement Uncertainty
PublikacjaThe most important parameter of each analytical result is its reliability. An analytical result is not a constant value; each result has two properties, error and uncertainty. The sources of both these parameters have to be known and their values determined (estimated). All analytical results are obtained by applying an appropriate measuring procedure. The need for reliable results requires application of reliable analytical procedures,...
-
The influence of the geographic positioning system error on the quality of ship magnetic signature reproduction based on measurements in sea conditions
PublikacjaIn previous studies, the authors performed the magnetic signature reconstruction of the marine ship Zodiak as part of the measurement campaign focused on recording magnetic data and the relative position of a ship during its passage over a magnetometer immersed on the testing ground. A high degree of representation of the magnetic signature was obtained. However, the recorded measurement data revealed new patterns of the multidipole model...
-
Selection of pointing device for elders
PublikacjaW artykule przedstawiono metodykę i sposób akwizycji oraz analizy danych dla doboru optymalnego urządzenia wskazującego, dostosowanego do osób starszych. Przedstawiono wyniki próbnych testów na dwóch grupach - docelowej i referencyjnej oraz skomentowano wyniki.
-
Earthquake-Induced Structural Pounding
PublikacjaEarthquake-induced structural pounding between insufficiently separated build-ings, or bridge segments, has been repeatedly observed during ground motions. The reports after earthquakes indicate that it may lead to some local damage in the case of moderate seismic events or may result in considerable destruction or even collapse of colliding structures during severe ground motions. Pounding in build-ings is usually caused by the...
-
The methodology for determining of the value of cutting power for cross cutting on optimizing sawing machine
PublikacjaIn the article the methodology of forecasting the energy effects of the cross-cutting process using the classical method, which takes into account the specific cutting resistance, is presented. The values of cutting power for the cross-cutting process of two types of wood (softwood and hardwood) were forecasted for the optimizing sawing machine with using presented methodology. The cross-cutting process with high values of feed...
-
Modus operandi of Qatar Resistance Policy against “Anti-Terror Quartet”
Publikacja -
Distance measurement errors in silent FM-CW sonar with matched filtering
PublikacjaThe secretiveness of sonar operation can be achieved by using continuous frequency-modulated sounding signalswith reduced power and significantly prolonged repeat time. The application of matched filtration in the sonarreceiver provides optimal conditions for detection against the background of white noise and reverberation, and avery good resolution of distance measurements of motionless targets. The article shows that target...
-
Errors of Surface Topography Parameter Calculation in Grinded or Turned Details Analysis
Publikacja -
Sources of errors associated with the determination of PAH and PCB analytes in water samples
PublikacjaW pracy przedstawiono problemy związane z oznaczaniem analitów z grupy WWA i PCB w próbkach wody. Zidentyfikowano źródła błędów. Szczególną uwagę zwrócono na:- proces adsorpcji analitów na ściankach szklanych naczyń używanych w trakcie obróbki i przechowywania próbek,- wpływ etapu odparowywania nadmiaru rozpuszczalnika z ekstraktów na odzysk analitów,- wpływ materiału, z którego jest wykonana kolumienka ekstrakcyjna (szkła, polietylenu)...
-
Reduction in Errors in Roughness Evaluation with an Accurate Definition of the S-L Surface
PublikacjaCharacterization of surface topography, roughly divided into measurement and data analysis, can be valuable in the process of validation of the tribological performance of machined parts. Surface topography, especially the roughness, can respond straightly to the machining process and, in some cases, is defined as a fingerprint of the manufacturing. When considering the high precision of surface topography studies, the definition...
-
Analysis of Positioning Error and Its Impact on High Frequency Performance Parameters of Differential Signal Coupler of Differential Signal Coupler
PublikacjaThis paper presents the analysis of the effect of differential signal coupler positioning accuracy on its high frequency performance parameters for contact-less high speed chip-to-chip data transmission on PCB application. Our considerations are continuation of the previous works on differential signal coupler concept, design methodology and analysis for high speed data transmission monitoring presented in [1, 2]. The theoretical...
-
Multiple output differential OTA with linearizing bulk-driven active-error feedback loop for continuous-time filter applications
PublikacjaA CMOS circuit realization of a highly linear multiple-output differential operational transconductance amplifier (OTA) has been proposed. The presented approach exploits a differential pair as an input stage with both the gate and the bulk terminals as signal ports. For the proposed OTA, improved linearity is obtained by means of the active-error feedback loop operating at the bulk terminals of the input stage. SPICE simulations...
-
Error analysis of calculating average d-q current components using Regular Sampling and Park transformation in FOC drives
PublikacjaIn electric drives using voltage source inverters, motor currents contain ripple component resulting from pulse-width modulated (PWM) voltage. The frequency range of the ripples is much higher than the bandwidth of current control. Therefore the control is performed on the basis of a fundamental current component, i.e. average value with the averaging time being the PWM period. In majority of cases the average current is measured...
-
New approaches to cutting resistance estimation of wood cutting process with circular-saw blades
PublikacjaTheoretical and experimental determination of values of cutting resistance belongs to the basic and simultaneously the most developed field of mechanics of this process. Energetic effects of wood sawing process are mainly calculated on the basis of the specific cutting resistance which, in wood cutting, is a function on a lot of factors. In this paper new method for calculation of cutting resistance is described. The latter method...
-
Coupled-Resonator Waveguide Filter in Quadruplet Topology With Frequency-Dependent Coupling - A Design Based on Coupling Matrix
PublikacjaThis letter presents an application of a recently developed coupling matrix synthesis technique to design of coupled-resonator filters with dispersive inter-resonator couplings. This technique is used to design a novel coupled-cavity bandpass filter. Measurements validate the design and confirm effectiveness of the synthesis method. The filter is a four-pole generalized Chebyshev filter with three transmission zeros. Resonators...
-
Optimal routing in a transportation network
Publikacja -
Productivity of wood cutting process
PublikacjaW artykule przedstawiono analizę przykładowej linii przecinania drewna. Produktywność linii oceniono na podstawie stopnia wykorzystania przecinarki i faktycznej prędkości przecinania.
-
Path Coloring and Routing in Graphs.
PublikacjaW rozdziale omówione zostały problemy kolorowania ścieżek i routingu w grafach. Podano podstawowe definicje związane z tymi problemami, znane wyniki wraz z dyskusją złożoności obliczeniowej dla grafów ogólnych i dla kilku podstawowych klas grafów oraz zastosowania.
-
Resilient Routing in Communication Networks
PublikacjaThis important text/reference addresses the latest issues in end-to-end resilient routing in communication networks. The work highlights the main causes of failures of network nodes and links, and presents an overview of resilient routing mechanisms, covering issues related to the Future Internet (FI), wireless mesh networks (WMNs), and vehicular ad-hoc networks (VANETs). For each of these network architectures, a selection of...
-
Taxonomy of Schemes for Resilient Routing
PublikacjaThis chapter provides a taxonomy of schemes for resilient routing followed by a discussion of their application to contemporary architectures of communication networks. In particular, a general classification of schemes for resilient routing is first presented followed by a description of the reference schemes for IP networks. The chapter in its later part focuses on the representative techniques of resilient routing for a multi-domain...
-
Mutual coupling of elliptical microstrip resonators
PublikacjaW artykule przedstawiono wyniki badań dotyczących wzajemnych sprzężeń w mikropaskowych promiennikach w kształcie prostokąta lub elipsy. W badaniach została wykorzystana dwuwymiarowa metoda przestrzeni widmowej, w której analizowane struktury oświetlane są pojedynczą falą płaską.
-
Hydrographic echosounder for sounding inland waters.
PublikacjaNowy model echosondy zaprojektowanej specjalnie dla instytucji administrującymi śródlądowymi drogami wodnymi, sztucznymi i naturalnymi zbiornikami oraz morskimi wodami przybrzeżnymi jest opisany. Podstawowym wymogiem wynikającym z sondażu wód płytkich jest pomiar możliwie najmniejszych głębokości. Przez zastosowanie oddzielnych przetworników (nadawczego i odbiorczego) i ich wytłumienie oraz przez wprowadzenie układu TVG o dużej...
-
Nonlinear modelling of eathquake induced pounding.
PublikacjaZaprezentowano nieliniowy model lepkosprężysty siły zderzenia w czasie kontaktu między konstrukcjami podczas trzęsień ziemi. Efektywność modelu sprawdzono przez porównanie wyników analizy numerycznej z wynikami eksperymentalnymi. Wyniki badań pokazują, iż rozważany model najdokładniej symuluje siłę zderzenia w czasie.
-
Influence of statistical errors on damage detection based on structuralflexibility and mode shape curvature
PublikacjaDamage detection procedures based on measured natural frequencies and building structure mode shapes are discussed in this paper. Modal curvature and structural flexibility approaches are tested. Attention is paid to the modal identification errors that influence damage detection. This problem is studied using a computer simulation of a simple supported beam. For practical cases, the peak picking methodand its statistical errors...
-
Relativistic Bennett Brassard cryptographic scheme, relativistic errors,and how to correct them.
PublikacjaWprowadzono opis polaryzacji liniowej oparty o główne zerowe kierunki transformacji Lorentza. Formalizm ten został zastosowany do problemu eliminacji błędów w kryptografii kwantowej.
-
Analysis of distance measurement errors in CW FM sonar with MLS code modulation
PublikacjaAlthough used in the classic silent sonar, the CW FM sounding signal has a major flaw which is its inaccuracy in determining the distance to a target. The authors of the article have developed a concept of silent sonar using frequency modulation signals switched by pseudorandom codes, already discussed in their previous work. This article presents a detailed analysis of errors in CW FM sonar with pseudo-random sequence code modulation...
-
Effect of manufacturing errors of the pad sliding surface on the performance of the hydrodynamic thrust bearing
PublikacjaIn the present study, investigation of the effect of manufacturing errors on the performance of large tilting pad thrust bearings has been performed, following a CFD-based Thermohydrodynamic analysis of a single pad. A 3D model has been generated, including the pad, the lubricant film and the corresponding part of the collar. The pad has been assumed to be deformed about the pivot point, due to thrust loading. Manufacturing errors...
-
Identification of the Vistula Mounting tower model using measured modal data
PublikacjaW pracy przedstawiono problem identyfikacji pięcioparametrowego modelu zabytkowej wieży twierdzy Wisłoujście. Poszukiwane parametry wyznaczono jako rozwiązanie problemu minimalizacji błędu średniokwadratowego pomierzonych dwóch pierwszych częstości i pierwszej postaci drgań własnych. Do tego celu wykorzystano hierarchiczną procedurę minimalizacji przy zastosowaniu analizy wrażliwości. Analiza numeryczna potwierdziła efektywność...
-
Clonal selection algorithm for vehicle routing
PublikacjaOver the years several successful computing techniques have been inspired by biological mechanisms. Studies of the mechanisms that allow the immune systems of vertebratesto adapt and learn have resulted in a class of algorithms called artificial immune systems. Clonal selection is a process that allows lymphocytes to launch a quick response to known pathogens and to adapt to new, previously unencountered ones. This paper presents...
-
A Novel Reliable Routing Scheme for VANETs
PublikacjaSieci bezprzewodowej transmisji informacji bazujące na rodzinie standardów 802.11, zastosowane w przypadku komunikacji między pojazdami (VANET), mogą istotnie przyczynić się do poprawy bezpieczeństwa ruchu drogowego. Z uwagi na wysoki stopień mobilności pojazdów, dobór tras w sieciach VANET jest problemem trudnym, zwłaszcza w przypadku transmisji wieloskokowej. Rozwiązania dostępne w literaturze ukierunkowane na poprawę dostępności...
-
Physicochemical treatment of used cutting fluids
PublikacjaBadano fizykochemiczne oczyszczanie przepracowanych cieczy obróbkowych pobranych z różnych źródeł przez rozdzielanie na frakcje: organiczną i wodną. Stosowano różne koagulanty (m.in. siarczan żelaza, chlorek żelaza) oraz polielektrolit Polyquant 20 U 050. Do wyznaczenia szybkości rozdziału emulsji wykorzystano Turbiscan Lab Expert. Ponadto wyznaczono optymalne warunki rozdziału faz emulsji (pH, temperatura oraz dawki koagulanta...
-
Modelling of cutting by means of fracture mechanics
PublikacjaThe suitability of modern fracture mechanic theory was proved for the estimation of the cutting force and the cutting specific resistance. This paper shows modification of Ernst-Merchant theory and its application for determination some other properties of wood sample. This theory is acceptable for evaluation of shear yield stresses and shear plane angle. Sawing by gang saw machine was used as a process similar to the orthogonal...
-
MODELLING OF CUTTING BY MEANS OF FRACTURE MECHANICS
PublikacjaThe suitability of modern fracture mechanic theory was proved for the estimation of the cutting force and the cutting specific resistance. This paper shows modification of Ernst-Merchant theory and its application for determination some other properties of wood sample. This theory is acceptable for evaluation of shear yield stresses and shear plane angle. Sawing by gang saw machine was used as a process similar to the orthogonal...