Filtry
wszystkich: 1391
-
Katalog
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: , MAGNETOACOUSTIC EMISSION
-
Emission profile of butan-2-one oxime from commercially available neutral silicone sealant
PublikacjaThe paper presents results of research on emission profile of butan-2-one oxime (methyl ethyl ketoxime, MEKO) released from two types of commercially available neutral silicone sealants: silicone type ‘S’ and silicone type ‘T’. To determine the emissions from silicone samples, the system consists of a stationary emission chamber, and the thermal desorption-gas chromatography-mass spectrometry system was applied. First, the research...
-
Performance and Emission Modelling and Simulation of Marine Diesel Engines using Publicly Available Engine Data
PublikacjaTo analyse the behaviour of marine diesel engines in unsteady states for different purposes, for example to determine the fuel consumption or emissions level, to adjust the control strategy, to manage the maintenance, etc., a goal-based mathematical model that can be easily implemented for simulation is necessary. Such a model usually requires a wide range of operating data, measured on a test stand. This is a time-consuming process...
-
Emission Profiles of Volatiles during 3D Printing with ABS, ASA, Nylon, and PETG Polymer Filaments
PublikacjaIn this short communication we characterize the emission of volatile organic compounds (VOCs) from fused filament fabrication (FFF) 3D printing using four polymer materials, namely polyethylene terephthalate glycol-modified (PETG), acrylonitrile styrene acrylate (ASA), Nylon, and acrylonitrile butadiene styrene (ABS). Detailed emission profiles are obtained during thermal degradation of the polymers as a function of temperature...
-
Advances in analysis, quantification and modelling of N2O emission in SBRs under various DO set points
PublikacjaNitrous oxide (N2O), considered a major greenhouse gas (GHG) in wastewater treatment plants (WWTPs), is produced during both nitrification and denitrification processes; hence, it needs to be controlled by internal and external strategies. Various factors, such as DO, temperature, and pH, could be incorporated into the mitigation of emissions in WWTPs. In this research, potential operational strategies were investigated in order...
-
Microcracking monitoring and damage detection of graphene nanoplatelets-cement composites based on acoustic emission technology
PublikacjaThis study aims to identify the micro-cracking pattern and structural applications of cement composites replaced with 0 wt%, 0.04 wt%, and 0.08 wt% contents of graphene nanoplatelets (GNPs) over cement weight through acoustic emission (AE) monitoring under mechanical degradation. The ultraviolet-visible spectroscopy (UV–vis) results showed that at 60 min sonication period, GNP-4 showed maximum absorbance rate of 16.15% compared...
-
Real-time monitoring of the emission of volatile organic compounds from polylactide 3D printing filaments
PublikacjaEstablishing the emission profile of volatile organic compounds generated during fused deposition modeling 3D printing using polymer filaments is important in terms of both understanding the processes taking place during thermal degradation of thermoplastics, and assessing the user's exposure to potentially harmful volatiles. However, obtaining detailed, real-time qualitative and quantitative results poses a challenge. In this...
-
Mathematical modelling of gasification process of sewage sludge in reactor of negative CO2 emission power plant
PublikacjaSewage sludge is a residue of wastewater processing that is biologically active and consists of water,organic matter, including dead and alive pathogens, as well as organic and inorganic contaminants suchas polycyclic aromatic hydrocarbons (PAHs) and heavy metals. Due to the nature of sewage sludge and itspossible influence on human health and wellbeing, it is a subject of various regulations. Currently,sewage sludge is considered...
-
Model-based identification of the dominant N2O emission pathway in a full-scale activated sludge system
PublikacjaActivated sludge models (ASMs), extended with an N2O emission module, are powerful tools to describe the operation of full-scale wastewater treatment plants (WWTPs). Specifically, such models can investigate the most contributive N2O production pathways and guide towards N2O and carbon footprint (CF) mitigation measures. A common practice is to develop and validate models using data from a single WWTP. In this study, a successfully...
-
Analysis of Roughness, the Material Removal Rate, and the Acoustic Emission Signal Obtained in Flat Grinding Processes
PublikacjaIn this work, the analysis of the acoustic emission (AE) signal in grinding processes is addressed. The proposed analysis method decomposes the acoustic signal into three frequency ranges. The total energy of each range is determined, as well as the highest frequency. Different grinding experiments were carried out, according to a full factorial design of experiments (DOE), in which feed speed, depth of cut, and transversal step...
-
Tunable emission and energy transfer of B2O3–Bi2O3–AlF3 glass system doped with Eu3+/Dy3+
PublikacjaThe structure and luminescent properties of the B2O3–Bi2O–AlF3 glass system doped with Eu3+/Dy3+ ions in different molar ratios were studied. A series of glasses were synthesized by the conventional melt quenching technique. Glass transition and crystallization temperatures were examined by Differential Thermal Analysis (DTA) measurements. The amorphous character of the prepared samples was confirmed by the X-ray diffraction (XRD)...
-
The Impact of Technological Processes on Odorant Emissions at Municipal Waste Biogas Plants
Publikacja -
The Effect of CO2 Gas Emissions on the Market Value, Price and Shares Returns
Publikacja -
A virtual instrument for the adaptive analysis of low-frequency magnetic-field emissions
Publikacja -
RDE Testing of Passenger Cars: The Effect of the Cold Start on the Emissions Results
Publikacja -
A comparison of exhaust emissions from vehicles fuelled with petrol, LPG and CNG
Publikacja -
The Comparison of the Emissions from Light Duty Vehicle in On-road and NEDC Tests
Publikacja -
Global development of emissions reduction strategies from light duty vehicles
Publikacja -
Analysis of the Influence of Fuel Sulphur Content on Diesel Engine Particulate Emissions
Publikacja -
Distribution of the International Marine Traffic Air Pollutant Emissions in the Port of Split
Publikacja -
Atmospheric emissions of POPs in Europe - a discussion of existing data and data need
PublikacjaZaproponowano, aby schematy inwentaryzacji i raportowania emisji w przyszłości były tak dobrane, aby zaspokajały potrzeby zarówno administracji odpowiedzialnej za strategię redukcji emisji jak i naukowców wykorzystujących inwentaryzację emisji na potrzeby dalszych badań naukowych. Stan obecny inwentaryzacji emisji POP oszacowany został jako niezadowalający a dalsze usprawnienia są konieczne dla poprawienia wiarygodności wyników...
-
Prediction of CO2 emissions of a car using the discrete map of the operating conditions
PublikacjaW pracy przedstawiono propozycję opisu warunków eksploatacji pojazdów w wybranej aglomeracji miejskiej z użyciem dyskretnej mapy warunków eksploatacji. Mapa taka umożliwia prognozowanie wybranych parametrów eksploatacyjnych pojazdów dla przyjętych dróg przejazdu oraz różnych jednostek napędowych. Głównymi parametrami wyznaczanymi z użyciem dyskretnej mapy warunków eksploatacji są: całkowita energia przeznaczana do napędu wybranego...
-
The influence of settable parameters of switching gasoline/LPG on exhaust toxic emissions
PublikacjaThe main objective of the studies shown in the paper was to develop a proper strategy for settable parameters of ECU to decrease total emission of toxic components in composition of exhaust during a cold start phase. The experimental research has been performed for engine running at idle and for engine running on the chassis dynamometer (performing European Driving Test NEDC).
-
Tomasz Zubowicz dr inż.
OsobyTomasz Zubowicz has received his M.Sc. Eng. degree in Control Engineering from the Faculty of Electrical and Control Engineering at the Gda{\'n}sk University of Technology (GUT) in $2008$. He received his Ph.D. Eng. (Hons.) in the field of Control Engineering from the same faculty in $2019$. In $2012$ he became a permanent staff member at the Department of Intelligent Control and Decision Support Systems at GUT and a member of...
-
Metody Admission Control oparte na pomiarach.
PublikacjaSterowanie przyjęciem zgłoszenia jest kluczowym elementem sterowania domeną DiffServ warunkującym świadczenie przez operatora usług z IP QoS. Zasadniczym celem pracy jest dokonanie analizy związanej z metodami AC opartymi na pomiarach określanych skrótem MBAC. Scharakteryzowane zostało sześć metod realizacji MBAC o różnej złożoności obliczeniowej i pomiarowej. Przedstawiona została także realizacja procesu pomiaro-wego wielkości...
-
Partial Admission Stages of High Efficiency for a Microturbine
PublikacjaThe paper presents the results of a design analysis of a microturbine for a cogeneration micro-power plant working in accordance with organic Rankine cycle. The heat power of the plant is assumed equal to 20kW and the corresponding available electric output is estimated to be about 3 kW. After the design analysis, the axial turbine with partial admission in all stages was built and tested experimentally. Special attentionwas paid...
-
Partial Admission Stages of High Efficiency for a Microturbine
PublikacjaThe paper presents the results of a design analysis of a micro-turbine for a co-generation micro-power plant working in accordance with organic Rankine cycle. The heat power of the plant is assumed equal to 20kW and the corresponding available electric output is estimated to be about 3kW. After the design analysis, the axial turbine with partial admission in all stages was built and tested experimentally. Special attention was...
-
The low-frequency magnetic field emissions on-board of the vessel
Dane BadawczeThe data represents measurement results performed on board of the vessel. The acquired time-waveforms, corresponding to the instantaneous values of the magnetic field (MF) induction were acquired near the cable supplying the bow thruster motor. Data recording of the magnetic field density (MFD) emissions was carried out with a/d converters of the data...
-
Narrow Red Emission Band Fluoride Phosphor KNaSiF6:Mn4+ for Warm White Light-Emitting Diodes
Publikacja -
Influence of the variability of the odour emission rate on its impact range: a case study of the selected industrial source
Publikacja -
The Importance of the Microclimatic Conditions Inside and Outside of Plant Buildings in Odorants Emission at Municipal Waste Biogas Installations
Publikacja -
Enzymatic Activity and Content of Polycyclic Aromatic Hydrocarbons (PAHs) in Soils under Low-Stack Emission in Lublin
Publikacja -
O 1s excitation and ionization processes in the CO2molecule studied via detection of low-energy fluorescence emission
Publikacja -
Towards a global historical emission inventory for selected PCB congeners - a mass balance approach. 3. An update
PublikacjaPoprzednie prace autorów zawierały bardzo istotne informacje do oceny stężeń związków polychlorobifenylowych (PCB) w rejonach oddalonych od dużych źródeł emisji tych związków jak i w środowisku globalnym. Okazało się, że niezbędna jest modyfikacja emisji PCB po roku 2000. Przedstawiono nowe dane o produkcji PCB w Polsce oraz nowe dane nt. składu chemicznego różnych produktów technicznych opartych na PCB. Ulepszono też metody oceny...
-
Mixing of excimer and exciplex emission: A new way to improve white light emitting organic electrophosphorescent diodes
PublikacjaW pracy opisano konstrukcję wydajnych diod elektrofosforescencyjnych emitujących światło białe. Emisja diod pochodzi od trypletowych monomerów PtL2Cl, trypletowych ekscymerów (PtL2Cl:PtL2Cl) i trypletowych ekscypleksów m-MTDATA (donor elektronu):PtL2Cl (akceptor elektronu), gdzie PtL2Cl oznacza organiczny kompleks platyny (II), a m-MTDATA - dendrymer aminowy. Kwantowa wydajność EL diody wynosi 6.5% fot./e. Współrzędne charakteryzujące...
-
Modelling long-term technological transition of Polish power system using MARKAL: Emission trade impact
PublikacjaThe need for technological transition of electricity production becomes a global problem. However, in coal-dominated Polish power system this need is even more crucial than anywhere, since technical lifetime of the most domestic power plants is ending. In this paper, the impact of the EU Emission Trading Scheme (EU ETS) for CO2 combined with sulfur dioxide (SO2) and nitrogen oxides (NOx) emission trading mechanism on power technology...
-
POSSIBILITY OF IDENTIFICATION OF TECHNICAL CONDITION OF BEARINGS FOR SELF-IGNITION ENGINES BY APPLICATION OF ACOUSTIC EMISSION AS A DIAGNOSTIC SIGNAL
PublikacjaThis paper presents the results of empirical studies where the acoustic emission (AE) method was applied to identify the technical condition of sliding surfaces of main and crank bearings for main diesel engines. The test results indicate that the measurements of the AE parameters allow the technical condition identification for bearings of this type. The results refer to the measurements of the parameters for AE generated in the...
-
INTERLABORATORY COMPARISON OF THE ELECTROMAGNETIC EMISSION MEASUREMENTS USING FAR AND GTEM TEST SITES UP TO 1 GHz
PublikacjaElectromagnetic emission limiting is one of the basic requirements in the European Directive 2014/30/EU (EMC Directive). Manufacturers often use alternative methods of measurements to make preliminary verification of emission. This paper presents and analyzes problem with comparison between measurements in different test sites: FAR (Fully Anechoic Room) and GTEM (Gigahertz Transverse Electromagnetic cell). FAR is assumed as the...
-
Motor Cable Influence on the Conducted EMI Emission of the Converter Fed AC Motor Drive. - Vol. 1
PublikacjaInvestigation of conducted electromagnetic interference in AC motor drives fed by pulse width modulated voltage converters requires considering parasitic capacitances in converters, motor windings and feeding cables to be taken into account. Motor voltage transients and related conducted electromagnetic emission are significantly correlated with resonance effects occurring in load circuits. The levels of intensity of these phenomena...
-
Optical Emission Spectroscopy of Microwave (915 MHz) Plasma in Atmospheric Pressure Nitrogen with Addition of Ethanol Vapour
PublikacjaIn this paper results of optical emission spectroscopic study of microwave 915 MHz plasma in atmospheric pressure nitrogen with an addition of ethanol vapour are presented. The plasma was generated in waveguide- -supplied cylinder-type nozzleless microwave plasma source. The aim of research was to determine the rotational Trot and vibrational Tvib temperatures of CN and C2. A method called bubbling was employed to introduce alcohol (ethanol)...
-
Up-conversion white emission and other luminescence properties of a YAG:Yb2O3·Tm2O3·Ho2O3@SiO2 glass-nanocomposite
PublikacjaWe report on a glass-nanocomposite material consisting of yttrium aluminum garnet (Y3Al5O12, YAG) nanocrystals co-doped with Yb3+, Tm3+ and Ho3+ ions as well as entrapped into a SiO2 xerogel. This 94YAG·5Yb2O3·0.8Tm2O3·0.2Ho2O3@SiO2 (abbr. YAG:YbTmHo@SiO2) nanocomposite material has been prepared by sol–gel procedure. Its structure and morphology has been characterized by means of X-ray diffraction (XRD) and scanning electron microscope...
-
High Frequency Conducted Emission in AC Motor Drives Fed By Frequency Converters: Sources and Propagation Paths
PublikacjaProvides a concise and thorough reference for designing electrical and electronic systems that employ adjustable speed drives Electrical and electronic systems that employ adjustable speed drives are being increasingly used in present-day automation applications. They are considered by many application engineers as one of the most interfering components, especially in a contemporarily faced industrial environment. This book fills...
-
Evaluation of the reference fuel consumption and CO2 emission of vehicle with using of the map of operating conditions for selected agglomeration
PublikacjaZaproponowana w pracy metoda tworzenia mapy warunków eksploatacji dla wybranej aglomeracji może zostać przeprowadzona przy wykorzystaniu tanich i prostych w obsłudze urządzeń. Podstawowym urządzeniem badawczym jest pojazd samochodowy wyposażony w system pomiaru położenia GPS z układem korekty wskazań wysokości i rejestracji parametrów jazdy. Zamieszczony w pracy przykład wykorzystania mapy warunków eksploatacji pokazuje możliwości...
-
Investigations of the Working Process in a Dual-Fuel Low-Emission Combustion Chamber for an FPSO Gas Turbine Engine
PublikacjaThis investigation is devoted to an analysis of the working process in a dual-fuel low-emission combustion chamber for a floating vessel’s gas turbine. The low-emission gas turbine combustion chamber with partial pre-mixing of fuel and air inside the outer and inner radial-axial swirlers was chosen as the object of research. When modelling processes in a dual-flow low-emission gas turbine combustion chamber, a generalized method...
-
Compact High Efficiency and Zero-Emission Gas-Fired Power Plant with Oxy-Combustion and Carbon Capture
PublikacjaReduction of greenhouse gases emissions is a key challenge for the power generation industry, requiring the implementation of new designs and methods of electricity generation. This article presents a design solution for a novel thermodynamic cycle with two new devices—namely, a wet combustion chamber and a spray-ejector condenser. In the proposed cycle, high temperature occurs in the combustion chamber because of fuel combustion...
-
A study on microcrack monitoring in concrete: discrete element method simulations of acoustic emission for non-destructive diagnostics
PublikacjaThe research is focused on the monitoring of fracture evolution in concrete beams under three-point bending using the acoustic emission technique and the discrete element method. The main objective of the study was to numerically and experimentally investigate the mechanism behind the generation of elastic waves during acoustic emission events and their interaction with micro- and macro-cracking in concrete beams under monotonic...
-
The Use of Chemical Sensors to Monitor Odour Emissions at Municipal Waste Biogas Plants
Publikacja -
Methods of Assessing Odour Emissions from Biogas Plants Processing Municipal Waste
Publikacja -
The Influence of Synthetic Oxygenates on Euro IV Diesel Passenger Car Exhaust Emissions
Publikacja -
Evaluation of a 10 nm Particle Number Portable Emissions Measurement System (PEMS)
Publikacja -
Impact of trajectory simplification methods on modeling carbon dioxide emissions from ships
PublikacjaModels of ship fuel consumption and emissions play an essential role in estimating global shipping’s greenhouse gas emissions. They are also widely used for verification of reported CO2 emissions for systems like EU MRV (Monitoring, Reporting and Verification) or IMO DCS (Data Collection System). Such models achieve high accuracy using historical spatiotemporal information about each ship from AIS data. However, this approach requires substantial...