Filtry
wszystkich: 1713
-
Katalog
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: SOFT-CRASH
-
The electrical properties mesurements of SOFC with Ce0.8Co0.15Cu0.05O2-s functional layer
Dane BadawczeThe dataset includes the electrical properties mesurements of SOFC with Ce0.8Co0.15Cu0.05O2-s layer. Samples were produced using aqueous soft chemistry methods (microemulsion method) and applied in form of a layer onto the anode of the commercial SOFC. The SOFC was working under biogas feeding at 750oC. The layers were sintered at 1100oC.
-
LS-DYNA simulations of the impacts of a 38-ton Heavy Goods Vehicle into a road cable barrier
PublikacjaNowadays, more and more attention is being paid to safety on roads and motorways. It is due to the continuous development of road and motorway network and a significant increase of the number of vehicles on roads. To meet the expectations of improving road safety in Poland, the Road Innovations Development (RID) research programme was implemented in 2016. The aim of the RID 3A - Road Safety Equipment (RoSE) project is a comprehensive...
-
Change of reaction quotients for SOFC fueled by biogas mixture at 750 C
Dane BadawczeThe dataset contains the Change of reaction quotients for SOFC fueled by biogas mixture at 750 C (60:40 CH4:CO2). The outlet concentration of the gases from SOFC were measured using novel FTIR-based unit.
-
The electrical properties mesurements of DIR-SOFC with Ce0.8Fe0.2O2-s functional layer
Dane BadawczeThe dataset includes the electrical properties mesurements of SOFC with Ce0.8Fe0.1O2-s layer. Samples were produced using aqueous soft chemistry methods (microemulsion method) and applied in form of a layer onto the anode of the commercial SOFC. The SOFC was working under biogas feeding at 750oC. The layers were sintered at 1100oC.
-
The electrical properties mesurements of DIR-SOFC with Ce0.8Co0.2O2-s functional layer
Dane BadawczeThe dataset includes the electrical properties mesurements of SOFC with Ce0.8Co0.1O2-s layer. Samples were produced using aqueous soft chemistry methods (microemulsion method) and applied in form of a layer onto the anode of the commercial SOFC. The SOFC was working under biogas feeding at 750oC. The layers were sintered at 1100oC.
-
The electrical properties mesurements of DIR-SOFC with Ce0.8Mn0.2O2-s functional layer
Dane BadawczeThe dataset includes the electrical properties mesurements of SOFC with Ce0.8Mn0.1O2-s layer. Samples were produced using aqueous soft chemistry methods (microemulsion method) and applied in form of a layer onto the anode of the commercial SOFC. The SOFC was working under biogas feeding at 750oC. The layers were sintered at 1100oC.
-
The electrical properties mesurements of DIR-SOFC with Ce0.8Ni0.2O2-s functional layer
Dane BadawczeThe dataset includes the electrical properties mesurements of SOFC with Ce0.8Ni0.1O2-s layer. Samples were produced using aqueous soft chemistry methods (microemulsion method) and applied in form of a layer onto the anode of the commercial SOFC. The SOFC was working under biogas feeding at 750oC. The layers were sintered at 1100oC.
-
The electrical properties mesurements of DIR-SOFC with CeO2-s functional layer
Dane BadawczeThe dataset includes the electrical properties mesurements of SOFC with CeO2-s layer. Samples were produced using aqueous soft chemistry methods (microemulsion method) and applied in form of a layer onto the anode of the commercial SOFC. The SOFC was working under biogas feeding at 750oC. The layers were sintered at 1100oC.
-
The electrical properties mesurements of DIR-SOFC with Ce0.8Cu0.2O2-s functional layer
Dane BadawczeThe dataset includes the electrical properties mesurements of SOFC with Ce0.8Cu0.1O2-s layer. Samples were produced using aqueous soft chemistry methods (microemulsion method) and applied in form of a layer onto the anode of the commercial SOFC. The SOFC was working under biogas feeding at 750oC. The layers were sintered at 1100oC.
-
English Language Bridging ( Crash ) Course for Chinese Students
Kursy Online -
Exsolution of Ni nanoparticles on the surface of cerium and nickel co-doped lanthanum strontium titanate as a new anodic layer for DIR-SOFC. Anti-coking potential and H2S poisoning resistance of the prepared material
PublikacjaThe aim of this study was to evaluate a new catalytic material for biogas fueled DIR-SOFC. This material was a perovskite-type SrTiO3 doped with La, Ce and Ni of a general formula La0.27Sr0.54Ce0.09Ni0.1Ti0.9O3-σ (LSCNT). Additional preparation steps were undertaken to promote a nickel exsolution process. Heat post-treatment of powders in a humidified H2 resulted in an intensive growth of nickel nanoparticles (NPs) while the temperature...
-
Robust procedure for flow coefficient calculation. W: Recent advances in simulation, computational methods and soft computing. Ed. W. Nikos, E. Ma-torakis. New York: WSEAS Press**2002 s. 152-155, 5 rys. bibliogr. 7 poz. Krzepka procedura obliczania współczynnika przepływu.
PublikacjaW pracy przedstawiono efektywne i szybkie metody obliczania współczynnikaprzepływu powietrza na podstawie znanych: stosunku ciśnień statycznych i oporności dźwiekowej (patrz norma ISO6358).
-
Numerical methods for the assessment of bridge safety barriers
PublikacjaThe paper presents a numerical study of the bus crash test for bridge safety barriers. The analysis is conducted with the use of explicit code LS-DYNA. The problem of hourglass effect in shell elements is discussed. The simulations of bus impact against the barrier show that the analyzed barrier withstands the impact forces and restrains the bus trajectory to the bridge road.
-
Ireneusz Kreja dr hab. inż.
OsobyAbsolwent klasy matematycznej I Liceum Ogólnokształcącego w Gdańsku im. Mikołaja Kopernika (1974). Absolwent Wydziału Budownictwa Lądowego Politechniki Gdańskiej (1979). Od 1979 pracuje na PG. W 1989 uzyskał doktorat (z wyróżnieniem), na Wydziale Budownictwa Lądowego, a w 2008 habilitował się (również z wyróżnieniem) na Wydziale Inżynierii Lądowej i Środowiska PG. Od 2011 jest profesorem PG. Na Politechnice Gdańskiej pełnił funkcje:...
-
Assessing vehicle restraint systems on horizontal curves
PublikacjaHorizontal curves, an element of road infrastructure, have a statistically high number of accidents. Considering that horizontal curves in the last ten years have had app. 10% of all road accidents representing app. 14% of all fatalities on Polish roads, the issue is serious and requires more research and proper road safety treatments. Data for 2007 - 2016 show that in the case of accidents on horizontal curves app. 45% of the...
-
Diffusive properties of solvent molecules in the neighborhood of a polymer chain as seen by Monte-Carlo simulations
Publikacja -
Force-induced structural changes in non-sulfated carrageenan based oligosaccharides – a theoretical study
Publikacja -
Synergistic effect of multi walled carbon nanotubes and reduced graphene oxides in natural rubber for sensing application
PublikacjaUtilizing the electrical properties of polymer nanocomposites is an important strategy to develop high performance solvent sensors. Here we report the synergistic effect of multi walled carbon nanotubes (MWCNTs) and reduced graphene oxide (RGO) in regulating the sensitivity of the naturally occurring elastomer, natural rubber (NR). Composites were fabricated by dispersing CNTs alone and together with exfoliated RGO sheets (thermally...
-
Transport properties of aqueous ionic liquid microemulsions: influence of the anion type and presence of the cosurfactant
PublikacjaTransport properties, viz. specific conductivity, dynamic viscosity and apparent diffusion coefficients, were measured as a function of water content in aqueous ionic liquid microemulsions containing 1-butyl-3- methylimidazolium hexafluorophosphate, [BMIM][PF6] and bis(trifluoromethanesulphonyl)imide, [BMIM][Tf2N], stabilized by the nonionic surfactant TX-100, or its mixture with a cosurfactant, i.e. butanol. The investigation covered...
-
Antagonist adhesion effects due to variable substrate surface
PublikacjaThe effects of variability of intrinsic adhesion within a joint have been studied using a single cantilever beam (SCB) test. Fracture energy was found not to be a simple function of relative areas of 2 surface pre-treatments: a 'weak' zone decreased strength more than expected from simple, additive considerations. By severing the adhesive along the strong-weak transition, fracture energy increased.The prior antagonist effect appears...
-
Emulsification alters simulated gastrointestinal proteolysis of β-casein and β-lactoglobulin
PublikacjaWe have studied the effect of the adsorption of milk proteins at the oil-water interface on their digestibility in simulated gastrointestinal environment. The investigations aimed to characterize how both the breakdown of the adsorbed proteins and the interactions with physiological surfactants, phosphatidylcholine (PC) and bile salts (BS), influence structural transformations of model, protein-stabilized food emulsions in the...
-
Physical crosslinking of hyaluronic acid in the presence of phospholipids in an aqueous nano-environment
PublikacjaHyaluronic acid and phospholipids are two components in the synovial joint cavity that contribute to joint lubrication synergistically. Molecular dynamics simulations were performed and hydrogen bonds in hyaluronic acid were analyzed to identify specific sites that are responsible for its physical cross-linking. Two molecular masses of hyaluronic acid, 10 kDa and 160 kDa, were considered. We use molecular dynamics simulations and...
-
ANALYSIS OF THE PUNCHING FAILURE MECHANISM IN WORKING PLATFORMS
PublikacjaPaper presents an analysis of the shear failure mechanism which occurs from the punching of a working platform layer in relation to its thickness, grain size arrangement and mechanical properties, taking into consideration the interaction with soft subgrade. The study is based on the observations of performance of natural scale structures (Streefkerk) and the results of model investigations numerically represented with the use...
-
Electrical measurement data for SOFC fueled by H2 and biogas mixture at 750 C
Dane BadawczeThe dataset contains the Electrical measurement data for SOFC fueled by H2 (30h) and biogas mixture at 750 C (60:40 CH4:CO2). The investigation of long-term electrical stability was performed during initial SOFC feeding with hydrogen (for 30 h) and further with biogas (for 90 h). The electrical properties of the fuel cell were measured using the HAMEG...
-
Change of catalytic parameters for SOFC fueled by H2 and biogas mixture at 750 C
Dane BadawczeThe dataset contains the Change of catalytic parameters for SOFC fueled by H2 and biogas mixture at 750 C (60:40 CH4:CO2). The outlet concentration of the gases from SOFC were measured using novel FTIR-based unit. The parameters are conversion rates, selectivities and yields of products
-
Thermogravimetric measurement (TG) of 20wt.% Ce0.8La0.2O2-NiO-YSZ anode for DIR-SOFC
Dane BadawczeThe daataset includes the thermogravimetric measurement (TG) of Ce0.8La0.2O2-NiO-YSZ anode for DIR-SOFC. The mesurement was performed under synthestic air atmosphere. The anode was composed of NiO-YSZ cermet composite (80 wt%) and Ce0.8La0.2O2-s additive (20wt%) with the addition of poroformer - PMMA granules 8um diameter (40 vol.% of whole powder volume)....
-
Electrical power measurement of reference SOFC fueled by biogas mixture at 750 C
Dane BadawczeThe dataset contains the electrical measurements of IV curves for SOFC without La0.27Sr0.54Ce0.09Ni0.1Ti0.9O3-s layer working under biogas and H2 feeding stream. The SOFC was reduced at 900C and conditioned for 12 h under H2 prior the measurements. The measurements were performed using Gamry potentiostat/galvanostat
-
ON ESTIMATION OF OCCUPANT SAFETY IN VEHICULAR CRASHES INTO ROADSIDE OBSTACLES USING NON-LINEAR DYNAMIC ANALYSIS
PublikacjaThe article describes a comparison of two general methods of occupants safety estimation based on a numerical examples. The so-called direct method is mainly based on the Head Injury Criterion of a crash test dummy in a vehicle with passive safety system while the indirect method uses a European standards approach to estimate impact severity level. Numerical simulations in LS-DYNA have been conducted.
-
Numerical analysis of lumbar spine injury during road safety barrier collision
PublikacjaPurpose: Enhancing road safety is a critical goal worldwide, necessitating the development of clear standards for road safety systems. This study focuses on lumbar spine (L-spine) compression injuries during collisions with concrete road safety barriers (RSBs). It aims to analyze internal forces during impact to understand L-spine injury biomechanics in such accidents. Methods: The research included a literature review, analyzing...
-
Pounding between high-rise buildings founded on different soil types
PublikacjaEarthquake-induced pounding is a phenomenon that has been often experienced in previous earthquakes. The aim of this study is to investigate the effect of the soil type on high-rise buildings experiencing earthquake induced-pounding. Pounding between 7-storey and 9-storey buildings is examined under five soil types defined in the ASCE 7-10 code which are hard rock, rock, very dense soil and soft rock, stiff soil and soft clay soil....
-
PolyCat-SOFC Ogniwa tlenkowe zasilane plastikami nie podlegającymi recyklingowi
ProjektyProjekt realizowany w Katedra Inżynierii Materiałów Funkcjonalnych WETI zgodnie z porozumieniem POLTAJ10/2022/50/PolyCatSOFC/2023 z dnia 2023-09-05
-
On the validation of the LS-DYNA Geo Metro numerical model
PublikacjaThe paper presents experiences gained during work with numerical model of Geo Metro vehicle used for simulations of crash tests with road safety barriers. Attention is drawn to the subject of tire/wheel breakage during collision events. Some methods for improvement of the model are presented in the paper. Several results for the normative vehicle numerical tests are introduced. Simulations were carried out using LS-DYNA finite...
-
Thermogravimetric measurement (TG) of 10 wt.% Ce0.8La0.2O2-NiO-YSZ anode for DIR-SOFC
Dane BadawczeThe daataset includes the thermogravimetric measurement (TG) of Ce0.8La0.2O2-NiO-YSZ anode for DIR-SOFC. The mesurement was performed under synthestic air atmosphere. The anode was composed of NiO-YSZ cermet composite (90 wt%) and Ce0.8La0.2O2-s additive (10wt%) with the addition of poroformer - PMMA granules 8um diameter (40 vol.% of whole powder volume)....
-
Change of exhaust gases concentration for SOFC fueled by H2 and biogas mixture at 750 C
Dane BadawczeThe dataset contains the Change of exhaust gases concentration for SOFC fueled by H2 (for 12h) and biogas mixture at 750 C (60:40 CH4:CO2). The outlet concentration of the gases from SOFC were measured using novel FTIR-based unit.
-
Electrical power measurement of LSCNT modified SOFC fueled by biogas mixture at 750 C
Dane BadawczeThe dataset contains the electrical measurements of IV curves for SOFC with La0.27Sr0.54Ce0.09Ni0.1Ti0.9O3-s layer working under biogas and H2 feeding stream. The SOFC was reduced at 900C and conditioned for 12 h under H2 prior the measurements. The measurements were performed using Gamry potentiostat/galvanostat
-
FTIR spectra of SOFC with LSCNT layer fueled by biogas mixture at 750 C (pure)
Dane BadawczeThe dataset contains the FTIR spectra collected during the electrical measurements DIR-SOFC with LSCNT layer. The SOFC was reduced at 800degC in H2 prior to mesurements. The spectra were collected every 10 min.
-
A Review of Hyperelastic Constitutive Models for Dielectric Elastomers
PublikacjaDielectric elastomers are smart materials that are essential components in soft systems and structures. The core element of a dielectric elastomer is soft matter, which is mainly rubber-like and elastomeric. These soft materials show a nonlinear behaviour and have a nonlinear strain-stress curve. The best candidates for modelling the nonlinear behaviour of such materials are hyperelastic strain energy functions. Hyperelastic functions...
-
The structure of dimethylsulfoxide-solvated magnesium and calcium ions in solution and the solid state, and overview of the coordination chemistry of hydrated and solvated alkaline earth metal ions
PublikacjaOznaczono strukturę w stanie stałym i ciekłym solwatowanych jonów magnezu i wapnia w dimetylosulfotlenku. Stwierdzono, ze jony te tworzą sześciokoordynacyjne solwaty ze średnią długością wiązań Mg-O i Ca-O 2.062(4) i 2.303(5)A. Przegląd literaturowy ukazał, że jony berylu i magnezu we wszystkich rozpuszczalnikach tworzą odpowiednio cztero- i sześciokoordynacyjne solwaty, podczas gdy jony wapnia i strontu istnieją jako ośmiokoordynacyjne...
-
The changes of outlet gases concentrations from SOFC with Ce(Pr,Sm)O2-s layers
Dane BadawczeThe dataset includes The changes of outlet gases concentrations from SOFC with Ce(Pr,Sm)O2-s layers. Samples were produced using aqueous soft chemistry methods (microemulsion method) and applied in form of a layer onto the anode of the commercial SOFC. The SOFC was working under biogas feeding.
-
Change of exhaust gases concentration for LSCNT modified SOFC fueled by biogas mixture at 750 C
Dane BadawczeThe dataset changes of exhaust gases concentrations (CH4,CO,CO2,H2) over working time for SOFC with La0.27Sr0.54Ce0.09Ni0.1Ti0.9O3-s layer. Concentrations were calculated based on the FTIR measurements and calibration files presented in coupled dataset.
-
Innovative Research Into Road Restraint Systems
PublikacjaKey to understanding the needs and building road infrastructure management tools to prevent and mitigate run-off-road accidents is to identify hazards and their sources which are a result of wrong design, construction, installation and maintenance of road restraint systems [1]. Building such tools requires advanced studies with field tests, simulations and models to demonstrate the effects of selected parameters on road user safety...
-
Incremental dynamic analysis and fragility assessment of buildings founded on different soil types experiencing structural pounding during earthquakes
PublikacjaThe effect of the soil type on buildings experiencing pounding during earthquakes is investigated in this study using the incremental dynamic analysis and fragility assessment methods. Three 3-D structures with different number of storeys (4, 6 and 8) were considered in this study. Three pounding scenarios between these three buildings were taken into account, i.e. pounding between 4-storey and 6-storey buildings, between 4-storey...
-
SPFR - metoda ponownego wykorzystania pasma w systemach radiokomunikacyjnych nowej generacji
PublikacjaW referacie zaproponowano nową metodę ponownego wykorzystania pasma częstotliwościowego SPFR (Soft-Partial Frequency Reuse) oraz przedstawiono wyniki badań symulacyjnych, które umożliwiają jej porównanie ze znanymi metodami SFR (Soft Frequency Reuse) i PFR (Partial Frequency Reuse). Metoda SPFR może być użyta do zwiększenia efektywności wykorzystania zasobów fizycznych w systemie LTE-A oraz systemach B4G. Zastosowanie metody SPFR...
-
Model Management for Low-Computational-Budget Simulation-Based Optimization of Antenna Structures Using Nature-Inspired Algorithms
PublikacjaThe primary objective of this study is investigation of the possibilities of accelerating nature-inspired optimization of antenna structures using multi-fidelity EM simulation models. The primary methodology developed to achieve acceleration is a model management scheme which the level of EM simulation fidelity using two criteria: the convergence status of the optimization algorithm, and relative quality of the individual designs...
-
Multi-objective electric distribution network reconfiguration solution using runner-root algorithm
Publikacja -
A multi-label text message classification method designed for applications in call/contact centre systems
Publikacja -
Ship weather routing featuring w-MOEA/D and uncertainty handling
PublikacjaThe paper presents a new version of evolutionary multi-objective weather routing (WR) for ships taking into account uncertainties of weather forecasts in route optimization. The method applies authors’ w-MOEA/D algorithm: MOEA/D framework incorporating Decision Maker’s (DM) preferences by means of w-dominance relation. Owing to this, DM preferences are taken into account throughout optimization, allowing the process to focus on...
-
An automatic selection of optimal recurrent neural network architecture for processes dynamics modelling purposes
PublikacjaA problem related to the development of algorithms designed to find the structure of artificial neural network used for behavioural (black-box) modelling of selected dynamic processes has been addressed in this paper. The research has included four original proposals of algorithms dedicated to neural network architecture search. Algorithms have been based on well-known optimisation techniques such as evolutionary algorithms and...
-
Multi-objective optimization of expensive electromagnetic simulation models
PublikacjaVast majority of practical engineering design problems require simultaneous handling of several criteria. For the sake of simplicity and through a priori preference articulation one can turn many design tasks into single-objective problems that can be handled using conventional numerical optimization routines. However, in some situations, acquiring comprehensive knowledge about the system at hand, in particular, about possible...
-
Preference-based evolutionary multi-objective optimization in ship weather routing
PublikacjaIn evolutionary multi-objective optimization (EMO) the aim is to find a set of Pareto-optimal solutions. Such approach may be applied to multiple real-life problems, including weather routing (WR) of ships. The route should be optimal in terms of passage time, fuel consumption and safety of crew and cargo while taking into account dynamically changing weather conditions. Additionally it must not violate any navigational constraints...