Filtry
wszystkich: 2119
-
Katalog
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: incompressible flows
-
A simplified energy dissipation based model of heat transfer for subcooled flow boiling
PublikacjaIn the paper a model is presented based on energetic considerations for subcooled flow boiling heat transfer. The model is the extension of authors own model developed earlier for saturated flow boiling and condensation. In the former version of the model we used the heat transfer coefficient for the liquid single-phase as a reference level, due to the lack of the appropriate model for heat transfer coefficient for the subcooled...
-
Experimental and Computational Analysis of the Ship Propeller in Open Water Conditions for Inclined Flow
PublikacjaThe paper presents the results of computational analyses simulating the open water tests of ship propeller in inclined flow. The results of computations are compared with the results of corresponding experimental analyses carried out in the towing tank of Ship Design and Research Centre (CTO S.A.). The object of the research was the model propeller identified as CP469. The aim of the study was to validate the results of numerical...
-
Magnetic semiconductor photocatalysts for the degradation of recalcitrant chemicals from flow back water
PublikacjaIn the present study treatability of persistent organic compounds from the flow back water after hydrauling fracturing was investigated. The combination of TiO2 photocatalyst and magnetic oxide nanoparticles enhance the separation and recoverable property of nanosized TiO2 photocatalyst. Fe3O4/ TiO2 and Fe3O4@SiO2/TiO2 nanocomposites were prepared by heteroagglomeration. The photocatalysts’ characteristics by X-ray diffractometry...
-
Methods of measurement signal acquisition from the rotational flow meter for frequency analysis
PublikacjaOne of the simplest and commonly used instruments for measuring the flow of homogeneous substances is the rotational flow meter. The main part of such a device is a rotor (vane or screw) rotating at a speed which is the function of the fluid or gas flow rate. A pulse signal with a frequency proportional to the speed of the rotor is obtained at the sensor output. For measurements in dynamic conditions, a variable interval between...
-
Experimental Validation of Numerical Model within a Flow Configuration of the Model Kaplan Turbine
PublikacjaThis paper investigates validation of flow within a model Kaplan turbine. This includes comparison of various turbulence models and their influence on torque and power generated by the turbine. Numerical results were compared with experimental data.
-
Numerical Analysis of Turbulent Flow over a Backward-facing Step in an Open Channel
PublikacjaComputational examinations of the flow field in an open channel having a single Backward--Facing Step (BFS) with a constant water depth of 1.5 m were performed. The effects of the expansion ratio, and the flow velocity along the reattachment length, were investigated by employing two different expansion ratios of 1.5 and 2, and eight various flow velocities of 0.5, 1, 2, 3, 4, 5, 7.5 and 10 m/sec in the Computational Fluid Dynamic...
-
Numerical investigation of multiphase blood flow coupled with lumped parameter model of outflow
PublikacjaPurpose The purpose of this paper is the application of the computational fluid dynamics model simulating the blood flow within the aorta of an eight-year-old patient with Coarctation of Aorta. Design/methodology/approach The numerical model, based on commercial code ANSYS Fluent, was built using the multifluid Euler–Euler approach with the interaction between the phases described by the kinetic theory of granular flow (KTGF). Findings A...
-
Multiscale model for blood flow after a bileaflet artificial aortic valve implantation
PublikacjaCardiovascular diseases are the leading cause of mortality in the world, mainly due to atherosclerosis and its consequences. The article presents the numerical model of the blood flow through artificial aortic valve. The overset mesh approach was applied to simulate the valve leaflets motion and to realize the moving mesh, in the aortic arch and the main branches of cardiovascular system. To capture the cardiac system’s response...
-
FLOW Zmniejszenie nasilenia ruchu drogowego poprzez stworzenie korzystnych warunków dla ruchu pieszego i rowerowego
ProjektyProjekt realizowany w Katedra Inżynierii Transportowej zgodnie z porozumieniem 635998 z dnia 2015-04-14
-
FLOW Zmniejszenie nasilenia ruchu drogowego poprzez stworzenie korzystnych warunków dla ruchu pieszego i rowerowego
ProjektyProjekt realizowany w Katedra Inżynierii Transportowej zgodnie z porozumieniem 331826/PnH/2016 z dnia 2016-11-28
-
Wave energy attenuation in fields of colliding ice floes. Part B: A laboratory case study
Publikacja -
Wave‐Induced Surge Motion and Collisions of Sea Ice Floes: Finite‐Floe‐Size Effects
Publikacja -
Removal of organic matter and nitrogen in an horizontalsubsurface flow (HSSF) constructed wetland undertransient loads
PublikacjaA monitoring campaign in a horizontal subsurface flow constructed wetland under the influence of transient loads of flow-rate, organic matter, nitrogen and suspended solids showed an irregular removal of COD and TSS and lower both removal efficiencies and mass removal rates than the ones observed in other studies for similar operating conditions. This circumstance is associated to the presence of large amount of particulate organic...
-
Close-Distance Optical Flow Fusion Using EKF for Multirotor UAV Position Estimation
Publikacja -
Simulation of water flow in double -porosity soils on unstructured grids with the finite element method.
PublikacjaRozważa sie model przepływu wody w gruntowym ośrodku o podwójnej porowatości. Model matematyczny uzyskano poprzez zastosowanie teorii homogenizacji zastosowanej do gruntów o bardzo dużej różnicy przepuszczalności.
-
The influence of a cone-in-cone insert on flow pattern and wall pressure in a full-scale silo
PublikacjaArtykuł opisuje przeprowadzone badania przepływów silosowych i naporu materiałów sypkich podczas napełniania i opróżniania silosu o średnicy 2.5 m wyposażonego we wkładkę "stożek w stożku''. Badania przeprowadzane były w Instytucie Badawczym Tel-Tek w Norwegii. Materiałem użytym był suchy piasek. Napór na ścianę mierzony był bezpośrednio za pomocą 10 czujników wbudowanych w ścianę. Badania eksperymentalne pokazały duży wpływ wkładki...
-
Estimation of the River Flow Synchronicity in the Upper Indus River Basin Using Copula Functions
Publikacja -
Numerical analysis of the flow rig for UWS spray examination in exhaust system-relevant conditions
PublikacjaIn the present study, a flow rig with optical access intended for spray investigations in exhaust system-relevant conditions was analysed in terms of flow and temperature in the spray area using numerical simulations. The operation of the rig was examined for a wide range of exhaust mass flow rates, temperatures and various forms of UWS (urea-water solution) spray plumes. The locations of the injector and thermocouple were verified....
-
Experimental investigation of the flow pattern and wall pressure distribution in a silo with double-cone insert
PublikacjaArtykuł opisuje przeprowadzone badania przepływów silosowych i naporu materiałów sypkich podczas napełniania i opróżniania silosu o średnicy 2.5 m wyposażonego we wkładkę "podwójny stożek". Badania przeprowadzane były w Instytucie Badawczym Tel-Tek w Norwegii. Materiałem użytym był suchy piasek. Napór na ścianę mierzony był bezpośrednio za pomocą 10 czujników wbudowanych w ścianę. Badania eksperymentalne pokazały duży wpływ wkładki...
-
Free surface flow modeling in numerical estimation of flood risk zones: a case study
PublikacjaNa przykładzie doliny Wisły w Warszawie przedstawiono metodę wyznaczenia stref zagrożenia powodziowego. Symulowana numerycznie powódź wywołana została potencjalnym przerwaniem obwałowania rzeki w okolicach Saskiej Kępy. Do obliczeń zastosowano opracowany w Katedrze Hydrotechniki Wydziału Inżynierii Lądowej i Środowiska Politechniki Gdańskiej model dwuwymiarowego, płaskiego przepływu wody ze swobodną powierzchnią.
-
Influence of geometry and surface morphology of the U-tube on the fluid flow in the range of various velocities
Publikacja -
Numerical and physical modeling of water flow over the ogee weir of the new Niedów barrage
Publikacja -
Prediction of flow boiling heat transfer coefficient for carbon dioxide in minichannels and conventional channels
PublikacjaIn the paper are presented the results of calculations using authors own model to predict heat transfer coefficient during flow boiling for carbon dioxide. The experimental data from various researches were scrutinised conducted for a full range of quality variation and wide range of mass velocity. The aim of the study was to test the sensitivity of the in-house model. The work shows the importance of taking into account surface...
-
Electrohydrodynamic flow patterns and collection efficiency in narrow wire-cylinder type electrostatic precipitator
PublikacjaRecently, narrow electrostatic precipitators (ESPs) have become a subject of interest because of their possible application for the cleaning of the exhaust gases emitted by diesel engines. Diesel engines emit fine particles, which are harmful to human and animal health. There are several methods for decrease particulate emission from a diesel engines, but up to now, these methods are not enough effective or very expensive. Therefore,...
-
Determination of pressure drop in flow condensation of HFE7000 in minichannels with account of non-adiabatic effects
PublikacjaFlow boiling and flow condensation are often regarded as two opposite or symmetrical phenomena involving the change of phase. There is a temptation to describe both these phenomena with one only correlation, however such method has yet to be suggested. From amongst the structures present in flow boiling and flow condensation at least the annular flow structure seems to be mostly appropriate to the common modeling. However, the shear...
-
Voltage and Reactive Power Load Flow Optimization in the Power System Using Fuzzy Logic
PublikacjaThe paper presents issues related to voltage control in the power system. An original method of reactive power flow optimization is considered, which leads to improved voltages in the power system and reduced active power losses. The optimization method is based on a procedure that employs fuzzy logic and is supported by a gradient search algorithm. The method has been implemented in PLANS software and verified.
-
PRESSURE DROP OF HFE7000 AND HFE7100 IN FLOW CONDENSATION IN MINICHANNELS WITH ACCOUNT OF NON-ADIABATIC EFFECTS
PublikacjaFlow boiling and flow condensation are often regarded as two opposite or symmetrical phenomena involving the change of phase. There is a temptation to describe both these phenomena with one only correlation. From amongst the structures present in flow boiling and flow condensation at least the annular flow structure seems to be mostly appropriate to the common modeling. However, the shear stress acting between vapor phase and liquid...
-
Influence of heterogeneous air entry pressure on large scale unsaturated flow in porous media
PublikacjaThe paper presents numerical simulations of water infiltration in unsaturated porous media containing coarse-textured inclusions embed- ded in fine-textured background material. The calculations are performed using the two-phase model for water and air flow and a simplified model known as the Richards equation. It is shown that the Richards equation cannot correctly describe flow in the presence of heterogeneities. How- ever, its...
-
Unstructured finite-volume meshes for two-dimensional flow in variably saturated porous media
PublikacjaW pracy opisano rozwiązanie równania przepływu nienasyconego w ośrodkach porowatych z wykorzystaniem metody objętości skończonych. Przedstawiono różne sposoby tworzenia siatki numerycznej. Przeprowadzono analizę wpływu sposobu uśredniania współczynnika filtracji między sąsiednimi objętościami skończonymi na dokładność wyników.
-
Space-mapping-based design flow of miniaturized broadband matching transformer with perforated metallization
PublikacjaA fast design procedure of unconventional passive components has been presented and experimentally validated on the basis of a wideband microstrip four-section matching transformer (50:6 OHm). A classic impedance matching circuit has been miniaturized by means of compact microstrip resonant cells (CMRCs) leading to a considerable length reduction (34%) together with minor degradation in its performance. The spacemapping-based design...
-
EHD Flow Measured by 2D PIV in a Narrow Electrostatic Precipitator with Longitudinal Wire Electrode
PublikacjaIn this paper, results of the electrohydrodynamic (EHD) flow patterns in two narrow ESPs with longitudinally-to-flow wire electrode arepresented. The influence of the ESP geometry on the EHD flow generated in the ESP was investigated. The results obtained from 2-dimensional(2D) Particle Image Velocimetry (PIV) showed similarities and differences of the particle flow in the wire-plate and wire-cylinder type ESP.
-
Hardware implementation of digital image stabilization using optical flow algorithm and FPGA technology
PublikacjaW artykule przedstawiono efektywną procedurę uproszczenia algorytmu przepływu optycznego oraz jego realizację w układzie programowalnym FPGA. Zmodyfikowany algorytm wykorzystuję metodę blokowego dopasowania podobszarów oraz jednowymiarową reprezentację podobszarów. Dodatkowo, funkcja korelacji oparta jest o normę L1. W rezultacie uzyskano zmniejszenie zużytych zasobów kosztem nieznacznej utraty dokładności. Zarówno dokładność,...
-
Application of artificial neural networks (ANN) as multiple degradation classifiers in thermal and flow diagnostics
PublikacjaPrzedyskutowano problem zwiększenia dokładności rozpoznawania wielokrotnych degradacji eksploatacyjnych urządzeń składowych dużych obiektów energetycznych. Zastosowani sieć neuronową (SSN) o skokowych funkcjach przejścia. Sprawdzono możliwości przyspieszenia treningu sieci neuronowych. Zastosowano modułową metodę budowy SSN, polegającą na dedykowaniu pojedynczej sieci do rozpoznawania tylko jednego typu degradacji.
-
Physical and numerical modelling of heat-flow processes in tangentially pulverized fuel-fired boiler
PublikacjaPraca przedstawia wykorzystanie eksperymentalnego modelowania fizycznego kwasowo-zasadowego do modernizacji kotła pyłowego z tangencjalną komorą spalania w aspekcie ograniczenia emisji toksycznych składników węgla, siarki i azotu oraz doboru optymalnych parametrów termodynamicznych mieszania i spalania. Dodatkowo, w celu porównania wyników pomiarów kotła po modernizacji, wykonano obliczenia numeryczne z zastosowaniem oprogramowania...
-
Numerical simulation of rapidly varied water flow in the ´Wild River´ type water slide
PublikacjaPrzedstawiono numeryczną analizę przepływu w zjeżdżalni wodnej typu "Dzika Rzeka". Jako model matematyczny przyjęto równania przepływu wody płytkiej. Wobec szybkozmiennego ruchu wody do rozwiązania zastosowano metodę objętości skończonych. Numeryczną symulację przepływu wykonano na trójkątnej siatce niestrukturalnej. Wyniki obliczeń porównano z obserwacjami na obiekcie rzeczywistym zainstalowanym w parku wodnym w Sopocie. Dodatkowo...
-
Physical and numerical modelling of flow pattern and combustion process in pulverized fuel fired boiler.
PublikacjaW pracy przedstawiono źródła powstawania toksycznych związków podczas procesu spalania, metody ich redukcji. Do tego zadania wykorzystano eksperymentalne modelowanie fizyczne i uzupełniono je modelowaniem numerycznym. Obie metody, techniki modelowania miały na celu optymalizację procesu spalania.Wyniki obliczeń numerycznych porównano z pomiarami.
-
Influence of porous coating on heat transfer during flow boiling of R22, R134a and R407C
PublikacjaPrzedstawiono wpływ pwłoki porowatej w pozionej rurce podczas wrzenia w przepływie i spadku ciśnienia czynników chłodniczych R22, R134a i R407C.
-
Three modes of electrochemical impedance spectroscopy measurements performed on vanadium redox flow battery
PublikacjaThis article presents an innovative approach to monitor working redox flow batteries using dynamic electrochemical impedance spectroscopy, diverging from the commonly sequential impedance methods carried out under potentiostatic or galvanostatic conditions close to the open circle voltage. The authors introduce a fresh variation of dynamic impedance measurement that leverages an amplitude-modulated multi-frequency alternating current...
-
Modelowanie hydraulicznych skutków katastrofy zapory wodnej. Modeling of dam-break water flow
PublikacjaPrzedstawiono numeryczne rozwiązanie równań przepływu wody płytkiej wywołanego katastrofą zapory wodnej. Przestrzenną dyskretyzację równań wykonano metodą objętości skończonych. Metodę zastosowano do prognostycznych obliczeń propagacji fali wezbraniowej wywołanej katastrofą zapory wodnej w dolinie rzeki Toce. Wyniki obliczeń porównano z dostępnymi (obcymi) pomiarami wykonanymi na fizycznym modelu doliny. Uzyskano zadowalającą...
-
Possibility of exact determination of thermal and flow degradation symptoms in on-line power objects diagnostics
PublikacjaPrzedyskutowano problem dokładności tworzenia symptomów degradacji dotyczących sprawności urządzeń składowych dużych obiektów energetycznych. W referacie zajęto się szczególnie metodami tworzenia wzorców sprawnej pracy w przypadku określania sprawności w układzie on-line i porównano ją z określeniem w systemie off-line. Do odtwarzania stanu referencyjnego zastosowano sieć neuronową statystyczną (SSN, ang. ANN) o nieskokowych funkcjach...
-
Comprehensive circumscribing of non-linearity cases of a water supply system with smooth flow control
PublikacjaW artykule opisano formalnie poprawne metody opisu matematycznego pracy pomp o płynnie regulowanych wydatkach oraz reduktorów ciśnienia i reduktorów przepływu w modelowaniu przepływów ustalonych zachodzących w systemach wodociągowych. Opisano metodę opartą o dynamiczną analizę wrażliwości systemu oraz metodę wykorzystującą charakterystyki hydrauliczne systemu wodociągowego. Przedstawiono wyniki symulacji wykorzystującej ww. metody...
-
Fluid–solid interaction on a thin platelet with high-velocity flow: vibration modelling and experiment
PublikacjaThe paper concerns the nonlinear behaviour of a thin platelet that is streamlined in an aerodynamic tunnel. The air velocity in the aerodynamic tunnel was at 858.9 km/h or 0.7 Ma (Ma—Mach number is a dimensionless quantity in fluid dynamics representing the ratio of flow velocity past a boundary to the local speed of sound). This experiment was numerically simulated using FSI (fluid–solid interaction) tools, namely the coupling...
-
Modelling water flow in unsaturated porous media: Accounting for nonlinear permeability and material heterogeneity
PublikacjaW pracy przedstawiono problematykę matematycznego modelowania przepływów w nienasyconych ośrodkach porowatych, ze szczególnym uwzględnieniem dwóch aspektów. Pierwszym z nich jest obliczanie średniego współczynnika przewodności hydraulicznej między węzłami siatki w numerycznym rozwiązaniu równania przepływu nienasyconego. Drugim zagadnieniem jest wpływ lokalnej zmienności parametrów ośrodka porowatego (współczynnika przewodności...
-
Numerical simulation of transient flow in storm sewers using standard and improved mccormack scheme
PublikacjaProblem przepływu wody w rurach kanalizacji deszczowej wiąże się z pewnymi specyficznymi zjawiskami zachodzącymi w przewodach podczas zjawisk burzowych. Jeśli rury zaczynają być całkowicie wypełnione wodą, można zaobserwować przejście z ruchu ze swobodną powierzchnią do ruchu pod ciśnieniem i odwrotnie. Takie zjawisko można zaobserwować również w kanałach kontrolowanych przez urządzenia sterujące, np. zasuwy. Ponadto ruch szybkozmienny...
-
Thermal-hydraulic issues of flow boiling and condensation in organic Rankine cycle heat exchangers
PublikacjaW pracy przedstawiono szereg zagadnień cieplno-przepływowych podczas wrzenia i kondensacji w przepływie w wymiennikach ciepła obiegu ORC. Uwzględniono przemiany fazowe. Analizowano zagadnienia stabilności pracy wymienników oraz ich dynamikę
-
Modular Approach for Modelling Warming Up Process in Water Installations with Flow-Regulating Elements
PublikacjaThe paper presents a new method for modelling the warming up process of a water system with elements regulating the flow in a stochastic manner. The paper presents the basic equations describing the work of typical elements which the water installation is composed of. In the proposed method, a new computational algorithm was used in the form of an iterative procedure enabling the use of boundary conditions that can be stochastically...
-
Signals Features Extraction in Radioisotope Liquid-Gas Flow Measurements using Autocorrelation Function
PublikacjaKnowledge of the two-phase flow structure is essential for the proper conduct of industrial processes. Description of liquid-gas flow regimes is possible by using of data analysis in time, frequency, or state-space domain. In this research studies, the autocorrelation function is applied for analysis of signals obtained for liquid-gas flow by use gamma-ray absorption. The experiments were carried out on the laboratory hydraulic...
-
Numerical modeling of cross-flow heat exchanger for air-conditioning purposes in preliminary study.
PublikacjaPraca przedstawia wyniki obliczeń numerycznych krzyżowego płytowo-rurowego wymiennika ciepła przeznaczonego do celów klimatyzacyjnych w początkowym etapie jego projektowania.
-
Application of vertical flow constructed wetlands for highly contaminated wastewater treatment: preliminary results
PublikacjaBasing on quantitative and qualitative characteristics of reject waters (RWC) generated during dewatering of digested sewage sludge on centrifuges in conventional WWTP and municipal landfill leachate (LL), the pilot constructed wetlands for treatment of both types wastewater were designed and built. In the paper the conception, design and assumed treatment efficiencies of the pilot plants are presented. The water balance of the...
-
A semi-empirical model for flow boiling heat transfer with account of the reduced pressure effect
PublikacjaIn the present study the attention was focused on the influence of reduced pressure on the predictions of heat transfer during flow boiling at the extensive range of pressures. The results of calculations were to test the sensitivity of the in-house flow boiling model with respect to the selection of the appropriate two-phase flow multiplier, which is one of the distinctive elements of that model. For this purpose a few two-phase...