Publikacje
Filtry
wszystkich: 396
Katalog Publikacji
-
Nanotubular Titanium Oxide Layers for Enhancement of Bone-Implant Bonding and Bioactivity
PublikacjaThe present paper describes the techniques to improve the bioactivity of titanium and enhance the bone-implant bonding ability by the electrochemical anodization to fabricate titania nanotube arrays (TiO2).
-
Biocompatibility and Bioactivity of Load-Bearing Metallic Implants
PublikacjaThe main objective of here presented research is to develop the titanium (Ti) alloy base composite materials possessing better biocompatibility, longer lifetime and bioactivity behaviour for load-bearing implants, e.g. hip joint and knee joint endoprosthesis. The development of such materials is performed through: modeling the material behaviour in biological environment in long time and developing of new procedures for such evaluation;...
-
Physicochemical and Mechanical Performance of Freestanding Boron-Doped Diamond Nanosheets Coated with C:H:N:O Plasma Polymer
PublikacjaThe physicochemical and mechanical properties of thin and freestanding heavy boron-doped diamond (BDD) nanosheets coated with a thin C:H:N:O plasma polymer were studied. First, diamond nanosheets were grown and doped with boron on a Ta substrate using the microwave plasma-enhanced chemical vapor deposition technique (MPECVD). Next, the BDD/Ta samples were covered with nylon 6.6 to improve their stability in harsh environments and...
-
Volumetric and torque efficiency of pumps during start-up in low ambient temperatures
PublikacjaThe volumetric, torque and total efficiency of hydraulic pumps change during start-up in low ambient temperatures, as well as in thermal shock conditions, un-til they reach the set conditions. The time to reach steady-state conditions de-pends on many parameters: ambient temperature, flow rate, fluid temperature, design of hydraulic units. The author carried out tests of hydraulic pumps in the Hydraulics Laboratory of the Faculty...
-
Modeling of Combined Phenomena Affecting an AUV Stealth Vehicle
PublikacjaIn the paper some results of research connected with modelling the basic stealth characteristics of an AUV vehicle are presented. First of all a general approach to design of the stealth AUV autonomous underwater vehicle under consideration is introduced. Then, the AUV stealth vehicle concept is briefly described. Next a method of modelling of the stealth characteristics is briefly described as well. As an example of the stealth...
-
Mechatronic Design Towards Investigation of the Temporo-Mandibular Joint Behaviour
PublikacjaA significant problem of the temporo-mandibular joint (TMJ) research is lack of data concerning geometry and position of TMJ discs. It leads to necessity of developing a driving method of the process optimization, which is based on chosen techniques of mechatronic design. In particular, the latter concerns a technique of experimentally supported virtual prototyping. On this stage, the research is characterized by well-verified...
-
Rigid finite elements and multibody modelling used in estimation and reduction of rod vibrations
PublikacjaIn the paper, a mechanical set composed of a robot (manipulator) and of an elastic beam is considered. The beam is fixed to the top of the robot structure. In most of the similar cases, undesired vibrations can be excited in the beam. They are especially significant, when dynamics in the robot braking period is examined. In the paper, estimation and modification of length of the braking period is proposed, in order to reduce the...
-
Bioactive core material for porous load-bearing implants
PublikacjaSo far state of knowledge on biodegradable materials is reviewed. Among a variety of investigated materials, those composed of polymers and ceramics may be considered as only candidates for a core material in porous titanium alloy. The collagen and chitosan among natural polymers, polyhydroxy acids among synthetic polymers, and hydroxyapatite and tricalcium phosphate among ceramics are proposed for further research. Three essential...
-
Fuzzy reasoning system design and assessment of load-bearing endoprostheses and their fabrication processes
PublikacjaZaproponowano piec zastosowan podejscia rozumowania rozmytego do rozwiazania problemów w dziedzinie biomechanikioraz inzynierii biomateriałów. Obejmuja one: (A) oszacowanie maksymalnych naprezen kontaktowych działajacych naendoproteze, (B) zaprojektowanie procesu spiekania dla otrzymania porowatego implantu, (C) opracowanie planu utleniania wcelu otrzymania struktury nanorurkowej na stopach Ti, (D) oraz (E) zaprojektowanie osadzania...
-
Design and Evaluation of the Platform for Weight-Shifting Exercises with Compensatory Forces Monitoring
PublikacjaDetails of a platform for the rehabilitation of people with severe balance impairment are discussed in the paper. Based upon a commercially available static parapodium, modified to fit force sensors, this device is designed to give a new, safe tool to physiotherapists. It is designed for the patients who cannot maintain equilibrium during a bipedal stance and need to hold to or lean on something during the rehabilitation. Visual,...
-
New generation of the satellite hydraulic pumps
PublikacjaHydraulic satellite machines are known and produced in many versions, recognizable by the number of humps on their inner rotor and external gear, and therefore by the number of cooperating gears (satellites). All known shapes were however designed on the base of preliminary assumption that rotor’s and external gear’s pitch lines are formed by merging arcs, tangent to each other in the. This assumption makes calculations easier,...
-
Jaw biomechanics: Estimation of activity of muscles acting at the temporomandibular joint
PublikacjaThe aim of this study was to elaborate a method of estimation of activity of surface muscles acting at the temporomandibular joint of the healthy subjects by using a surface electromyography (EMG). The scope of this study involved testing chosen jaw motions (open, close, lateral deviation) and process of mastication occurring during eating food with different toughness (chewing gum, cereal and carrot) by using mixed sides, right...
-
A New Rehabilitation Device for Balance Impaired Individuals
PublikacjaIn the paper authors present a device designed to improve the rehabilitation process of people with balance impairment. The discussed device (JStep) utilizes a commercially available static standing frame (stander) modified in order to fit force sensing units under the feet and in the pillows around the hips of a patient. While executing rehabilitation tasks, the patient may compensate his balance deficiency by leaning on the pillows...
-
Simplified Map-based Selection of Optimal Spindle Speeds When Milling Complex Structures
PublikacjaIn the paper a method for selecting optimal spindle speeds for complex structures during milling operations is presented. It is based on the selection of the spindle speed in accordance with a simple equation resulting from the minimisation of vibration energy, which leads to the minimisation of the work of cut-ting forces presented in previous elaborations by the authors [1]. Optimal spindle speeds are obtained for many points...
-
Experiment-aided virtual prototyping to minimize tool-workpiece vibration during boring of large-sized structures
PublikacjaThe paper presents the author's method of solving the problems of vi-bration suppression during boring of large-sized workpieces by means of an in-novative method of adjusting the rotational speed of the boring bar. It consists in selecting the spindle speed in accordance with the results of the cutting process simulation. The method includes identification of the model of the finite element method of the boring bar. The Root Mean...
-
Rigid finite elements and multibody modeling in analyses of a robot shaped elastic/plastic deformations of a beam
PublikacjaDynamics analysis of a system composed of a parallel manipulator and of an elastic beam is presented in the paper. Classic 3RRR parallel manipulator is considered and used to deform the beam. Elasto-plastic deformations are investigated. Rigid-finite-elements technique is employed to deal with dynamics of the beam. A multibody structure is associated with the introduced hybrid system in order to model its dynamics. Idea of the...
-
FEX a Fingers Extending eXoskeleton for Rehabilitation and Regaining Mobility
PublikacjaThis paper presents the design process of an exoskeleton for executing human fingers’ extension movement for the rehabilitation procedures and as an active orthosis purposes. The Fingers Extending eXoskeleton (FEX) is a serial, under-actuated mechanism capable of executing fingers’ extension. The proposed solution is easily adaptable to any finger length or position of the joints. FEX is based on the state-of-art FingerSpine serial...
-
Maszyny rozdmuchowe stosowane do wytwarzaniu butelek z PET
PublikacjaScharakteryzowano maszyny wykorzystywane w procesie wytwarzania pojemników PET w procesie rozdmuchiwania z jednoczesnym rozciąganiem półfabrykatów w postaci preform. Omówiono typy, budowę oraz systemy i podsystemy, producentów oraz cykl pracy maszyny rozdmuchowej. Nie omówiono szczegółowo wytwarzania półfabrykatów do postaci preform w procesie wtryskiwania.
-
Charakterystyka faz rozdmuchu preform z poli(tereftalanu etylenu) w procesie rozdmuchiwania z jednoczesnym ich rozciąganiem
PublikacjaScharakteryzowano proces wytwarzania pojemników PET w procesie rozdmuchiwania z jednoczesnym rozciąganiem półfabrykatów w postaci preform. Największy nacisk położono na szczegółowe omówienie poszczególnych etapów procesu rozdmuchiwania oraz etapów pracy maszyny rozdmuchowej. Omówiono też wybrane zagadnienia przepływu powietrza podczas procesu rozdmuchiwania butelek. Poruszono również problem przemian fazowych tworzywa PET występujących...
-
On the durability of the hydraulic satellite motor working mechanism in overload condition
PublikacjaThe paper presents the newest construction of the hydraulic satellite pump/motor. In this study, the fracture of the hydraulic satellite motor working mechanism is investigated. Factors influencing the durability of satellite working mechanism have been described. The durability of the hydraulic satellite motor working mechanism at a load, corresponding to a pressure of 15 MPa supplied with refined rapeseed oil is very low. Analyses...
-
Port-based approach to distributed transfer function method
PublikacjaIn the paper there is presented an uniform, port-based approach to modeling of both lumped and distributed parameter systems. Port-based model of distributed system has been defined by application of distributed transfer function method (DTFM). The approach proposed combines versatility of port - based modeling and accuracy of distributed transfer function method. It enables to formulate appropriate input data for computer analysis...
-
Three Editions of Inter-University Studies on Space and Satellite Technology. Candidate and/vs. Graduate, a Case Study
PublikacjaCurrently, there is a growing demand for most up-to-date academic courses that will fulfil the needs of modern society. Each candidate has to make choices and judgements carefully, in order to succeed on the market. This is particularly important when educating individuals with different backgrounds, especially on an inter-university course in the field of space sciences and technology. This paper describes a case study carried...
-
Minimization of vibrations during milling of flexible structures using mechatronic design techniques
PublikacjaThe paper presents an innovative effective method of minimizing vibrations during milling of flexible structures, using a new vibration suppression method based on a workpiece holder with adjustable support stiffness. The proposed method is rooted in mechatronic design techniques, which can become a standard procedure for optimizing the milling process.
-
Proportional-Derivative and Model-Based Controllers for Control of a Variable Mass Manipulator
PublikacjaIn the paper, numerical analysis of dynamics of a variable mass manipulator is presented. A revolute joints composed manipulator is considered. Payload of the gripper is considered as the only element characterized by unknown value of its mass (variable between subsequent operations). As in other cases of the revolute joints composed manipulators, its behaviour dependents significantly on the pose of the manipulator. When the manipulator...
-
Projekt aCiret odpowiedzią na wyzwania przemysłu 4.0
PublikacjaDruga dekada XXI w. jest początkiem nowej rewolucji przemysłowej, określanej jako przemysł 4.0. Coraz powszechniejsze systemy cyberfizyczne, internet rzeczy, obliczenia i procesy sterowane w chmurze wymagają wysoko wykwalifikowanych pracowników, uzbrojonych w ogólną i specjalistyczną wiedzę oraz doświadczenie, wykazujących się przedsiębiorczością i inicjatywą. Problem braku odpowiedniej kadry dotyka firmy z sektora przemysłowego,...
-
W poszukiwaniu wspólnego mianownika dla nauk kosmicznych
PublikacjaW artykule zajęto się zagadnieniami znaczenia nauk kosmicznymi dla rozwoju kraju, a przede wszystkim dla kreowania innowacyjnej i konkurencyjnej gospodarki. Omówiono sprawy związane z organizacją i strukturą sektora kosmicznego. Szczególną uwagę poświęcono powiązaniu technologii kosmicznych i satelitarnych z sektorem morskim oraz szeroko pojętym bezpieczeństwem.
-
Measurements of the Hydraulic Fluids Compressibility
PublikacjaPerformance of the hydrostatic high-pressure drive systems is affected by the changes of working fluid’s volume. Presence of air bubbles in the fluid cause this problem to be even more serious. To study this phenomenon precise measurements of fluid’s bulk modulus are necessary. Differ-ent measurement methods are applied, but they are either limited to low pressure range or give inaccurate results. To solve the problem the new...
-
Metodologia badania skrzyni biegów z wykorzystaniem układu hydraulicznego jako hamowni
PublikacjaW artykule przedstawiono metodologię prowadzenia badań mechanicznej skrzyni biegów. Sposób prowadzenia pomiarów zaprezentowano na przykładzie badań wybranej przekładni. Przedstawiono i opisano różne konfiguracje stanowiska badawczego wykorzystującego układ hydrauliczny, który pełnił funkcję hamowni. Zawarto opis konstrukcji prototypowej przekładni będącej obiektem badań. Ponadto omówiono przykładowe charakterystyki uzyskane w ramach...
-
Lessons learned during SRAD hybrid motor development
PublikacjaStudent Researched and Developed (SRAD) hybrid rocket motor H-15 with total impulse of 15 $kNs$ was built. First version of the engine has average thrust of 3 $kN$, the second, improved one is prepared with an aim to have average thrust of 5 $kN$. Engine development was started from scratch and went through phases of: definition of design assumptions and constraints, numerical modelling to predict engine performance, CAD and CAM...
-
Using differential pressure sensor to measure nitrous oxide level in a tank
PublikacjaA method for measuring the level of liquid nitrous oxide oxidizer in a hybrid rocket motor oxidizer tank is proposed. Presented approach is more accurate than the most commonly used method of this measurement, which employs weighting of the whole sounding rocket or an oxidizer tank. In our solution we use a differential pressure sensor to measure the change of pressure at the bottom of an oxidizer tank in comparison to the pressure...
-
Multi-layered mineral glass units used as viewport elements of underwater ship structures
PublikacjaIn the paper, Authors deals with viewport elements of underwater marine constructions. If a single-plate viewport constructions are considered, big thicknesses of the glass plate are required to resist the pressure. To build the viewports from the commercially accessible glass panes, multi-layered glass units are proposed in the paper. Numerical calculations are presented, summarized and compared with experimental tests. Focusing...
-
Metody analizy wytrzymałości konstrukcji wykonanych za pomocą technologii przyrostowej FDM i ich zastosowanie do warunków pracy przekładek okien podwodnych
PublikacjaDrukowanie 3D to technologia wytwarzania fizycznego obiektu poprzez nanoszenie kolejnych warstw materiału. W pracy zaprezentowano szereg badań eksperymentalnych i numerycznych, mających na celu zbadanie wpływu ułożenia włókien wydruku na jego własności mechaniczne. Analiza otrzymanych wyników prowadzi do wniosku, że wytrzymałość wydruku uzależniona jest od wielu parametrów druku, takich jak wysokość warstwy, kąt ułożenia włókien,...
-
Platforma aktywnego nauczania dla zwiększenia poziomu umiejętności techników i inżynierów
PublikacjaPrzemysł 4.0 całkowicie przekształca sektor wytwórczy w Unii Europejskiej wprowadzając zasady cyfryzacji procesów przemysłowych. W rezultacie, nowe cyber-fizyczne systemy produkcyjne wywierają ogromny wpływ na siłę roboczą, a zwłaszcza na techników i inżynierów. Systemy te wymagają nowych hybrydowych zespołów "człowiek – maszyna", w których technicy i inżynierowie powinni umieć analizować zbiory danych Big Data, tworzyć symulacje...
-
Investigating lubricants behaviour in microgravity for vibration damping purposes
PublikacjaVibration is one of the harshest environments an object is exposed to during and after launch into space on a launch vehicle. Such vibrations should be damped to avoid destruction of the spacecraft or its elements. Currently, active and material damping is used. A possibility of using lubrication as the damping factor is suggested by some research. MoS2 is a typical solid lubricant used in space applications. Its properties vary...
-
Modelowanie zachowania układu mięśni
PublikacjaW rozdziale są opisane podejścia do zamodelowania zachowania zespołu mięśni, które są oparte o zasady mechaniki. Zgodnie z tymi zasadami problem zamodelowania zachowania zespołu mięśni należy rozwiązać jako odwrotne lub proste zadanie dynamiki. Odwrotne zadanie dynamiki pozwala na wyznaczenie sił/momentów generowanych przez poszczególne mięśnie na podstawie danych kinematycznych, tzn. trajektorii ruchu oraz jej pochodnych (prędkości...
-
Opinia dotycząca naruszenia praw do zgłoszenia patentowego P.402847 pt.: "Ręczna wiertarka górnicza"
PublikacjaEkspertyza dotyczy naruszenia praw do zgłoszenia patentowego P.402847 pt.: "Ręczna wiertarka górnicza"
-
Opinia w sprawie patentu PL 215741 pt.: „Napęd hydrauliczny” udzielonego przez Urząd Patentowy RP na rzecz firmy Spitznas Maschinenfabrik GmbH
PublikacjaWskazano i opisano błędy merytoryczne w patencie nr 215741 oraz wskazano i opisano wspólne cechy maszyn będących przedmiotem zastrzeżeń w patentach nr 215741, 200588 i 185724
-
Mechanika ogólna : Rozwiązywanie zagadnień z MATHCAD-em
PublikacjaW książce zaprezentowano nową metodę studiowania mechaniki, umożliwiającą kształtowanie intuicji inżynierskiej. W tym celu wykorzystano program MATHCAD, który usprawnia żmudne obliczenia i pozwala zaoszczędzić czas na dokładną analizę rozważanych zjawisk oraz otrzymanych wyników. Książka polecana studentom na zajęcia z mechaniki ogólnej oraz jako praktyczną pomoc przy wykonywaniu prac dyplomowych, a także inżynierom szukającym...
-
Drgania mechaniczne : Rozwiązywanie zagadnień z MATHCAD-em
PublikacjaAutor proponuje jednoczesne poznawanie teorii drgań mechanicznych i wdrażanie jej do analizy własności dynamicznych układów mechanicznych. Stosuje do tego celu wspomaganie komputerowe za pomocą programu MATHCAD. Wyjaśnia naturę zjawiska drgań mechanicznych i jego znaczenie w technice oraz wpływ na środowisko. Prezentuje też wzorcowe programy pomocne przy samodzielnym programowaniu obliczeń. Podaje zasady tworzenia modeli dyskretnych...
-
Analysis of Crash Computation on a Basis of the Pronciple of Linear Momentum and Kinetic Energy
PublikacjaThe article shows the calculation of a vehicle crash with a fixed pile, modelled by the finite element method. There were compared during the crash simulations changes in kinetic energy, as well as – changes in linear momentum and its derivative, with respect to time. Calculations were made in the HyperWorks CAE software environment. The obtained results show influence of various body parts and devices of the deceleration on...
-
Vision-based motion analysis of kitesurfer
PublikacjaKitesurfing is a relatively recent phenomenon with raising popularity worldwide – a recently developed extreme water sport considered a high-risk injury sport. It combines elements of several other sports, in particular sailing, surfing, windsurfing, wakeboarding, and snowboarding. The main purpose of authors’ research in the present paper is to use a vision system technique for measuring a kitesurfer’s body movements in order...
-
Wpływ parametrów eksploatacyjnych oraz przecieków na wartość skoków ciśnienia w pompie tłoczkowej z rozrządem krzywkowym
PublikacjaPublikacja stanowi kontynuację artykułu "Analiza zjawisk dynamicznych w komorze cylindrowej pompy PWK o zmiennej wydajności" z monografii Cylinder 2010. Praca stanowi uszczegółowienie wcześniejszej publikacji oraz jej rozszerzenie o wyniki badań oraz symulacji, a także szczegółowo porusza temat przecieków w oknie rozrządu, który we wcześniejszych publikacjach był tylko wspomniany.
-
Influence of Additional Loads on Chosen Gait Parameters and Muscles Activity
PublikacjaThis paper is devoted to human motion analysis and comparison of chosen kinematics parameters during normal gait with and without additional load in a form of backpack. A stability in both cases were compared in both frontal and sagittal planes, by applying a video tracking system. Experimental tests performed on treadmill, passive markers, placed on volunteers bare skin were used. Additionally, an infra-red camera was employed...
-
Właściwości mechaniczne tworzywa PET - przegląd literatury
PublikacjaThe article describes the influance of the microstructure and environment conditions on the mechanical properties of PET material. From the microskopic point of view, mechanical and thermal properties of PET material have the biggest influance on orientation and crystallization processes of material. From the macroskopic point of view mechanical properties can be described by parameters derived from strees-strain mechanical answers...
-
Satelitowe maszyny wyporowe. Podstawy projektowania i analiza strat energetycznych
PublikacjaMonografia poświęcona jest najnowszym konstrukcjom pomp i silników hydraulicznych satelitowych, nad którymi prace projektowe, badawcze i rozwojowe są prowadzone w laboratorium Hydrauliki i Pneumatyki Politechniki Gdańskiej od 2007 roku. W monografii wykazano, że jest możliwe zbudowanie maszyn satelitowych dla dwóch przypadków pracy satelitowego mechanizmu roboczego. Pierwszy przypadek dotyczy mechanizmu z obracającą się planetą,...
-
Hydropower-place in the future
PublikacjaWskazano na nieomijalną potrzebę rozwijania technologii dla małej energetyki wodnej, w szczególności o najniższych spadach. Widzi się w tym przyszłościowe wsparcie dla narastającej potrzeby ochrony wód jako naturalnego środowiska człowieka degradowanego postępem cywilizacyjnym.
-
Problems of the starting and operating of hydraulic components and systems in low ambient temperature (Part I)
PublikacjaW artykule przestawnie są problemy rozruchu i działania zespołów i układów hydraulicznych w niskich temperaturach otoczenia. Z tych powodów autor przebadał hydrauliczne zespoły i układy w warunkach szoku termicznego (oziębione zespoły zasilano gorącym czynnikiem roboczym). Określono parametry rozruchu w tych warunkach kilku zespołów oraz układów hydraulicznych, przy których ich eksploatacja jest bezpieczna. Badania eksperymentalne...
-
Nowe metody przetwarzania sygnałów w wybranych zagadnieniach wibroakustyki
PublikacjaMonografia Nowe Metody Przetwarzania Sygnałów w Wybranych Zagadnieniach Wibroakustyki będąca piętnastym Tomem z serii Monografie Katedry Automatyzacji Procesów AGH w Krakowie poświęcona jest zagadnieniom związanym z zastosowaniem i wykorzystaniem metod przetwarzania sygnałów wibroakustycznych w wybranych problemach technicznych i medycznych. W pierwszym rozdziale niniejszej monografii przedstawiono zagadnienia dotyczące metod przetwarzania...
-
Próba wykonania analizy modalnej desek kitesurfingowych
PublikacjaKitesurfing jako młoda dyscyplina sportu wciąż wymaga wielu badań. Polscy sportowcy, zwłaszcza kobiety, prezentują światowy poziom w kategorii freestyle i regularnie zdobywają najwyższe laury. Ze sportem ekstremalnym wiążą się również kontuzje. By poznać schemat ich powstawania, należy najpierw określić rozkład sił działających na zawodnika.
-
THE INFLUENCE OF PET MECHANICAL PROPERTIES ON SBM PROCESS PARAMETERS – LITERATURE REVIEW
PublikacjaIn the paper it is said about the influence of PET (polyethylene terephthalate) mechanical properties on SBM (stretch blow molding) process output parameters changes. The below paper mentions also about the influence of PET orientation and crystallization processes on mechanical and thermal properties of PET material during SBM process. All mechanical data of PET material and SBM process output parameters changes are from collected...