Publikacje
Filtry
wszystkich: 218
Katalog Publikacji
Rok 2020
-
70 LAT PRAKTYKI POMIAROWEJ W OCENIE WŁAŚCIWOŚCI UZIEMIEŃ METODĄ UDAROWĄ
PublikacjaPrzedstawiono liczącą ok. 70 lat historię prac związanych z rozwojem sposobów oceny uziemień wykorzystujących metodę udarową. Pierwsze prace związane z tym zagadnieniem zostały rozpoczęte w połowie ubiegłego wieku na Politechnice Gdańskiej z inicjatywy profesora Stanisława Szpora. Omówiono metodę pomiaru, stosowane kolejne generacje mierników, możliwości oceny uziemień i różne definicje normalizacyjne opisujące właściwości uziemienia...
-
Compressive Sensing Approach to Harmonics Detection in the Ship Electrical Network
PublikacjaThe contribution of this paper is to show the opportunities for using the compressive sensing (CS) technique for detecting harmonics in a frequency sparse signal. The signal in a ship’s electrical network, polluted by harmonic distortions, can be modeled as a superposition of a small number of sinusoids and the discrete Fourier transform (DFT) basis forms its sparse domain. According to the theory of CS, a signal may be reconstructed...
-
Estimating the uncertainty of discharge coefficient predicted for oblique side weir using Monte Carlo method
PublikacjaSide weir is a hydraulic structure, which is used in irrigation systems to divert some water from main to side channel. It is installed at the entrance of the side channel to control and measure passing water into the side channel. Many studies provided side weir water surface profile and coefficient of discharge to measure water discharge diverted into the side channel. These studies dealt with different side weir shapes (rectangular,...
Rok 2022
-
A numerical and experimental analysis of multi-hole orifice in turbulent flow
PublikacjaIn this research study, the comprehensive metrological analysis is investigated for a 4-hole orifice with module m = 0.25 installed in the pipeline with an internal diameter of 50 mm. A detailed numerical simulation was performed for the turbulence models: k-ε-realizable and k-ω-BSL. The novelties of the research include model validation by comparing the results of numerical studies with the experiment conducted in the area of...
-
AC Motor Voltage and Audible Noise Dataset
PublikacjaThe dataset titled AC motor voltage and audible noise waveforms in ship’s electrical drive systems with frequency converters contains the voltage and sound measurement results recorded in a marine frequency controlled AC drive system. The dataset is part of research focussing on the impact of the ship’s electrical drive systems with frequency converters on vibrations and the level of audible noise on ships. The dataset allows the...
Rok 2016
-
A simplified behavioral MOSFET model based on parameters extraction for circuit simulations.
PublikacjaThe paper presents results on behavior modeling of general purpose Metal-Oxide Semiconductor Field-Effect Transistor (MOSFET) for simulation of power electronics systems requiring accuracy both in steady-state and in switching conditions. Methods of parameters extraction including nonlinearity of parasitic capacitances and steady-state characteristics are based on manufacturer data sheet and externally measurable characteristics....
-
Air flow phenomena in the model of the blind drift
PublikacjaIn the presented paper, Particle Image Velocimetry (PIV) has been used to investigate flow pattern and turbulent structure in the model of blind drift. The presented model exist in mining, and has been analyzed to resolve ventilation issues. Blind region is particularly susceptible to unsafe methane accumulation. The measurement system allows us to evaluate all components of the velocity vector in channel cross-section simultaneously....
-
Current based Normalized Triple Covariance as a bearings diagnostic feature in induction motor
PublikacjaDiagnosis of induction motors, conducted remotely by measuring and analyzing the supply current is attractive with the lack of access to the engine. So far there is no solution, based on analysis of current, the credibility of which allow use in industry. Statistics of IM bearing failures of induction motors indicate, that they constitute more than 40% of IM damage, therefore bearing diagnosis is so important. The article provides...
-
Current-based higher-order spectral covariance as a bearing diagnostic feature for induction motors
PublikacjaConducting the diagnosis of induction motors remotely by analyzing the supply current is an attractive prospect with the lack of access to the engine. Currently, there is no solution, based on analysis of the current, the credibility of which would allow its use in industry. The statistics of bearing failures in induction motors indicate that they constitute more than 40% of induction motor damage, therefore, bearing diagnosis...
-
Cyfrowe przetworniki napięcie - częstotliwość i częstotliwość - napięcie
PublikacjaPrzedstawiono metody i układy realizowane w technice mikroprocesorowej do przetwarzania napięcie – częstotliwość i częstotliwość – napięcie oraz analizę dokładności, która umożliwia dopasowanie charakterystyk przetworników do parametrów przetwarzanego sygnału i ograniczenie poziomu błędów.
-
Diagnostyka obwodów elektrycznych magnesów nadprzewodzących
PublikacjaW ramach międzynarodowego projektu FAIR, którego uczestnikiem jest również Polska, budowany jest obecnie w Darmstad (Niemcy) akcelerator kołowy. Będzie on służyć do rozpędzania ciężkich jonów do prędkości bliskich prędkości światła. Akcelerator ten będzie zbudowany z magnesów nadprzewodzących co pozwoli m.in. na minimalizację strat energii elektrycznej. Utrzymanie magnesów akceleratora w stanie nadprzewodnictwa wymaga kontroli...
Rok 2023
-
Accounting for the distributions of input quantities in the procedure for the measurement uncertainty evaluation when calibrating the goniometer
PublikacjaThe discords concerning the measurement uncertainty evaluation in the Guide to the Expressing of Uncertainty in Measurement (GUM) and its Supplement 1 are considered. To overcome these discords, the authors of the paper propose to use the kurtosis method and the law of the propagation of the expanded uncertainty. Using the example of the goniometer calibration, the features of accounting for the distribution laws of input quantities...
-
Akademia Inżynierska w Polsce jako kontynuatorka tradycji przedwojennej Akademii Nauk Technicznych
PublikacjaPrzedstawiono historię Akademii Nauk Technicznych i Polskiej Akademii Nauk Technicznych. Omówiono genezę i działalność Akademii Inżynierskiej w Polsce.
-
Assessment of the Accuracy of a Virtual Multi-Channel Temperature Measuring Instrument
PublikacjaThe multi-channel temperature measurement system developed works with NTC thermistors. The article presents the results of theoretical and empirical evaluation of accuracy obtained in measurement channels. The basis for the theoretical assessment is the mathematical model for each of the measurement channels and the characteristics of the system elements included in the circuits of the measurement channel. Two different methods were...
-
Biocompatibility and potential functionality of lanthanum-substituted cobalt ferrite spinels
PublikacjaBulk and nanostructurized lanthanum-cobalt spinels have attracted a lot of interest from researchers, due to their unique physical and chemical properties as well as functionalities, which are interesting for biomedical and electronic industries. In this manuscript we show that introducing small lanthanum (La3+) content can tune magnetic, electronic and cytotoxic properties of the CoFe2− xLaxO4 system (x ≤ 0.1). The mechanisms...
-
Cylindrical orifice testing in laminar flow with the orifice diameter ratio β = 0.5
PublikacjaThe paper presents the results of an experimental study of a cylindrical orifice with the orifice diameter ratio β = 0.5 and the flow opening length‑to‑diameter ratio L/d = 1, with hydraulic oil flowing in the DN50 measuring channel. The measurements of the values characterising the oil flow were made in the laminar flow regime, for the Reynolds numbers ranging between Re = 100 to 950. Based on the experimental tests, standard...
Rok 2013
-
An Analysis of Uncertainty and Robustness of Waterjet Machine Positioning Vision System
PublikacjaThe paper presents a new Automatic Waterjet Positioning Vision System (AWPVS) and investigates components of workpiece positioning accuracy. The main purpose of AWPVS is to precisely identify the position and rotation of a workpiece placed on a waterjet machine table. Two webcams form a basis for the system, and constitute its characteristics. The proposed algorithm comprises various image processing techniques to assure a required...
-
Analiza mocy chwilowej do celów diagnostyki łożysk.
PublikacjaW artykule przedstawiono tematykę dotyczącą diagnostyki łożysk przy wykorzystaniu metody badawczej, opartej na pomiarze i analizie sygnału mocy chwilowej pobieranej przez silnik indukcyjny. Zaprezentowano przykładowe wyniki wykonanych pomiarów w oparciu o zaproponowaną metodę. Na podstawie przeprowadzonej analizy sformułowano wnioski dotyczące możliwości wykorzystania sygnału mocy chwilowej jako symptomu diagnostycznego, przeznaczonego...
-
ASPEKTY BEZPIECZEŃSTWA W OCENIE WYNIKÓW POMIARÓW UZIEMIEŃ ODGROMOWYCH
PublikacjaOcena rozległego systemu za pomocą metod wykorzystujących przebiegi wolnozmienne prowadzi do zbyt optymistycznych wniosków odnośnie ich właściwości podczas odprowadzania prądów wyładowań atmosferycznych. Bardziej bezpieczne wnioski powstają w wyniku pomiarów z zastosowaniem metody wykorzystującej przebiegi impulsowe, ponieważ wtedy jest uwzględniana tylko ta część nawet bardzo rozległego systemu uziemień, która bierze udział w...
-
Błędy cyfrowej rejestracji prędkości obrotowej z wykorzystaniem przetwornika obrotowo-impulsowego
PublikacjaPrzedstawiono zasadę działania przetwornika obrotowo-impulsowego w zastosowaniu do pomiaru prędkości obrotowej. Omówiono metody rejestracji on-line sygnału impulsowego z przetwornika obrotowo-impulsowego. W metodach tych prędkość obrotowa wyznaczana jest na podstawie ostatniego przedziału miedzyimpulsowego lub na podstawie dwóch ostatnich przedziałów miedzyimpulsowych z ekstrapolacji. Dla sinusoidalnej zmiany prędkości udowodniono,...
-
Comparison of induction motor bearing diagnostic test results through vibration and stator current measurement
PublikacjaThe paper discusses results of tests performed by authors, related to the angine bearings diagnostic using vibration and stator current measurements. The paper contains the description of an automatic measurement system, developed for measurement of those harmonics and processing that to obtain bearing diagnostic information. System was tested on objects with intentionally made defects in bearings, results of this test was also...
-
Diagnostyka łożysk silnika indukcyjnego na podstawie prądu zasilającego przy użyciu sztucznych sieci neuronowych
PublikacjaW artykule zawarto wyniki badań dotyczące diagnostyki łożysk silnika indukcyjnego na podstawie pomiarów prądu zasilającego z wyko-rzystaniem sztucznych sieci neuronowych. Zaprezentowano wyniki uczenia sieci oraz rezultaty testów przeprowadzonych na danych spoza zbioru uczącego. Badania wykonane zostały na obiektach z celowo wprowadzonymi uszkodzeniami łożysk. Przedstawiona nowa koncepcja zakłada użycie zestawu sieci neuronowych...
-
Diagnostyka łożysk silnika indukcyjnego na podstawie prądu zasilającego przy użyciu sztucznych sieci neuronowych
PublikacjaW artykule zawarto wyniki badań dotyczące diagnostyki łożysk silnika indukcyjnego na podstawie pomiarów prądu zasilającego z wykorzystaniem sztucznych sieci neuronowych. Zaprezentowano wyniki uczenia sieci oraz rezultaty testów przeprowadzonych na danych spoza zbioru uczącego. Badania wykonane zostały na obiektach z celowo wprowadzonymi uszkodzeniami łożysk. Przedstawiona nowa koncepcja zakłada użycie zestawu sieci neuronowych...
-
DIAGNOSTYKA ŁOŻYSK SILNIKA INDUKCYJNEGO PRZY UŻYCIU POMIARU PRĄDU ZASILAJĄCEGO I WIBRACJI
PublikacjaW artykule przedstawione zostały wyniki badań diagnostycznych łożysk silnika indukcyjnego z zastosowaniem metody pomiaru prądu zasilającego oraz wibracji. Poruszone zostały problemy dotyczące poszukiwania nowej metody opartej na pomiarze i analizie prądu, która w znacznym stopniu ułatwiłaby szybkie i sprawne znalezienie uszkodzenia w maszynie, bez konieczności bezpośredniego dostępu do badanego urządzenia. Zaprezentowano rezultaty...
Rok 2019
-
Analysis and interpretation of radiometric signals in a liquid-gas bubble flow
PublikacjaThe article presents the analysis of signals from a radiometric system consisting of two scintillation probes and two gamma radiation sealed sources. Calculations and interpretation were carried out for the bubble flow of the water-air mixture in the horizontal pipeline. The analysis of the obtained signals was done in time and frequency domain. In the frequency domain, a range of usable frequencies was identified, which were associated...
-
Determination of the uncertainty of mass flow measurement using the orifice for different values of the Reynolds number
PublikacjaStandard orifice flowmeters are widely used in the chemical and energy industry. Therefore, it is essential to know how accurate the measurements made with these instruments are. The paper presents an estimation of measurement uncertainty of a liquid mass flow using the orifice plate. The authors will present the influence of ranges of the Reynolds number on the estimated uncertainty, obtained on the basis of simulation and laboratory...
Rok 2014
-
Analysis of radiometric signal in sedimentating suspension flow in open channel
PublikacjaThe article discusses issues related to the estimation of the sedimentating solid particles average flow velocity in an open channel using radiometric methods. Due to the composition of the compound, which formed water and diatomite, received data have a very weak signal to noise ratio. In the process analysis the known determining of the solid phase transportation time delay the classical cross-correlation function is the most...
-
Application of gamma densitometry and statistical signal analysis to gas phase velocity measurements in pipeline hydrotransport
PublikacjaThe work presents selected methods of signal analysis used in the processing of data obtained from radiometric probes. The used data came from an exemplary study of a two-phase liquid-gas flow at the laboratory installation. In such rigs many possible transport types may be observed, i.e. slug, plug and bubble flow, and each of them gives different signal-to-noise ratio of recorded data. Therefore, available radiometric methods...
-
E-Technologies in Teaching Research Methodology for Engineers – a Case Study of the Course for International Postgraduate Students
PublikacjaThe Research Methodology course for postgraduate students is challenging, even for an experienced academic teacher. The primary objective of this course is to prepare participants to conduct scientific research and publish the results. This case study presents an original teaching method applied to Research Methodology with Emphasis on Engineering Science, for international engineering students at...
Rok 2017
-
Application of ANN and PCA to two-phase flow evaluation using radioisotopes
PublikacjaIn the two-phase flow measurements a method involving the absorption of gamma radiation can be applied among others. Analysis of the signals from the scintillation probes can be used to determine the number of flow parameters and to recognize flow structure. Three types of flow regimes as plug, bubble, and transitional plug – bubble flows were considered in this work. The article shows how features of the signals in the time and...
-
Customization of UWB 3D-RTLS Based on the New Uncertainty Model of the AoA Ranging Technique
PublikacjaThe increased potential and effectiveness of Real-time Locating Systems (RTLSs) substantially influence their application spectrum. They are widely used, inter alia, in the industrial sector, healthcare, home care, and in logistic and security applications. The research aims to develop an analytical method to customize UWB-based RTLS, in order to improve their localization performance in terms of accuracy and precision. The analytical...
-
Detection of inter-turn faults in transformer winding using the capacitor discharge method
PublikacjaThe paper presents results of an analysis of inter-turn fault effects on the voltage and current waveforms of a capacitor discharge through transformer windings. The research was conducted in the frame of the Facility of Antiproton and Ion Research project which goal is to build a new international accelerator facility that utilizes superconducting magnets. For the sake of electrical quality assurance of the superconducting magnet...
-
Diagnostyka łożysk silnika indukcyjnego z wykorzystaniem analizy prądu silnika metodą potrójnej kowariancji.
PublikacjaPrzedmiotem niniejszej rozprawy doktorskiej jest opracowanie nowej metody diagnostyki łożysk w silniku indukcyjnym opartej na pomiarach i analizie prądu zasilającego silnik. Ze względu na ciągłe doskonalenie i rozwój badao w kierunku metod prądowych, za pomocą których możliwa byłaby diagnostyka całego silnika, temat ten jest cały czas otwarty i jak najbardziej aktualny. Rozdział pierwszy zawiera wprowadzenie w zagadnienia będące...
-
Estimating the uncertainty of the liquid mass flow using the orifice plate
PublikacjaThe article presents estimation of measurement uncertainty of a liquid mass flow using the orifice plate. This subject is essential because of the widespread use of this type of flow meters, which renders not only the quantitative estimation but also qualitative results of this type so those measurements are important. To achieve this goal, the authors of the paper propose to use the theory of uncertainty. The article shows the...
-
Evaluation of expanded uncertainty of instantaneous power measurement in a bearing diagnostic system.
PublikacjaThe paper presents the issues concerning the estimation of the expanded uncertainty in the system for the diagnosis of rolling bearings, consisting of transducers: voltage and current voltage, which is used for diagnostic bearing motors method based on the measurement and analysis of the instantaneous power signal consumed by the induction motor. It presents the methodology for assessing the measurement uncertainty and presents...
Rok 2015
-
Application of gamma densitometry and statistical signal analysis to gas phase velocity measurements in pipeline hydrotransport
PublikacjaThe work presents selected methods of signal analysis used in the processing of data obtained from radiometric probes. The used data came from an exemplary study of a two-phase liquid-gas flow at the laboratory installation. In such rigs many possible transport types may be observed, i.e. slug, plug and bubble flow, and each of them gives different signal-to-noise ratio of recorded data. Therefore, available radiometric methods...
-
Computer System for Evaluation of Shock Hazard in Circuits with Non-sinusoidal Earth Currents
PublikacjaEffects of current on people are mainly considered for 50/60 Hz sinusoidal current and smooth direct current. However, modern low voltage circuits are very often equipped with power electronics converters – rectifiers, frequency converters, therefore non-sinusoidal earth currents (touch currents) occur. For non-sinusoidal currents safety criteria should be modified. This paper presents a computer system, based on LabVIEW environment,...
-
Estimation of the uncertainty of the AC/AC transducer output voltage
PublikacjaThe paper presents a methodology for estimating uncertainty of voltage transducers processing function, on the example of CYVS411D07 voltage transducers. The analysis was conducted using the method based on the GUM Guide propagation of uncertainty law and the determination of the coverage factor based on the effective number of degrees of freedom (t-Student distribution). The paper also presents example evaluation results of measured...
-
Estimation of the uncertainty of the LEM CV 3-500 transducers processing function
PublikacjaThe paper presents the methodology for estimating uncertainty of a voltage transducer processing function based on the example of LEM CV 3-500 transducer. The analysis was performed using the method based on the GUM Guide propagation of uncertainty law and the Monte Carlo numerical method. The article also presents a comparative analysis of the results of a voltage measurement evaluation done using the Monte Carlo simulation method,...
Rok 2002
-
Automatyzacja sprawdzania dokładności elementów układu do pomiaru prądu. Zastosowanie Komputerów w Nauce i Technice.XII cykl seminariów zorganizowanych przez PTETiS, Oddział Gdańsk.
PublikacjaDla diagnostyki silnika indukcyjnego przy wykorzystaniu pomiarów prądu został stworzony układ pomiarowy, składający się z przetworników pomiarowych, filtrów, komputera z kartą aktywizacji danych. Ocena jakości uzyskiwanych informacji diagnostycznych wymaga m.in. wiedzy o dokładności użytego sprzętu. Dla oceny dokładności zastosowanych elementów zbudowano skomputeryzowany system pomiarowy. Przedstawiono strukturę systemu jak...
-
Błędy w autokalibracyjnych pomiarach prądu uziemienia przy użyciu cęgów prądowych
PublikacjaWe współczesnych miernikach rezystancji uziemienia normą staje się możliwość kontroli wybranego uziemienia pracującego w systemie uziemień bez odłączania go od tego systemu. Prąd płynący przez uziemienie mierzy się przy użyciu przetwornika cęgowego. Znaczną poprawę dokładności pomiarów można uzyskać poprzez zastosowanie pomiaru autokalibracyjnego.
Rok 2018
-
Comparison of noise reduction methods in radiometric correlation measurements of two-phase liquid-gas flows
PublikacjaTwo-phase liquid-gas flows occur frequently in the mining, energy, chemical, and petrochemical industries. One of non-contact methods used to analyse these flows is the gamma ray absorption method. However, the signals received from radiation detectors contain a significant stochastic noise, which makes them difficult to analyse. The article describes four methods of noise reduction in cross-correlation measurements of water-air...
-
Diagnostyka łożysk silnika indukcyjnego poprzez analizę prądu silnika metodą NTC. Część I – opis zastosowanej metody
PublikacjaW artykule zaprezentowano nową metodę przetwarzania sygnału prądu silnika indukcyjnego do celów diagnostyki łożysk oraz jej walidację przy pomocy badań eksperymentalnych. Badania przeprowadzono dla trzech różnych uszkodzeń łożysk przy pełnym obciążeniu silnika. Pierwsza część artykułu zawiera wprowadzenie do tematyki diagnostyki łożysk, przegląd metod diagnostycznych oraz podstawy teoretyczne zastosowanej przez autora metody. W...
-
DIAGNOSTYKA ŁOŻYSK SILNIKA INDUKCYJNEGO POPRZEZ ANALIZĘ PRĄDU SILNIKA METODĄ NTC. CZĘŚĆ II – WYNIKI BADAŃ EKSPERYMENTALNYCH
PublikacjaW artykule zaprezentowano nową metodę przetwarzania sygnału prądu silnika indukcyjnego do celów diagnostyki łożysk oraz jej walidację przy pomocy badań eksperymentalnych. Badania przeprowadzono dla trzech różnych uszkodzeń łożysk przy pełnym obciążeniu silnika. Pierwsza część artykułu zawiera wprowadzenie do tematyki diagnostyki łożysk, przegląd metod diagnostycznych oraz podstawy teoretyczne zastosowanej przez autora metody. W...
-
Digital Processing of Frequency–Pulse Signal in Measurement System
PublikacjaThe work presents the issue of the use of multichannel measurement systems of sensors processing input value to impulse signal frequency. The frequency impulse signal obtained from such sensors is often required to be processed at the same time with a voltage signal which is obtained from other sensors used in the same measurement system. In such case, it is usually necessary to sample the output signals from all sensors in the...
-
Evaluation of the structures size in the liquid-gas flow by gamma-ray absorption
PublikacjaThe rapid development of tomography methods particularly electrical, X and gamma rays allows for a wide range of the information about flow structure. However, all of such methods are quite complicated. At the same time much simpler systems as the measuring system of gamma rays absorption, allows to obtain a all key flow information which describe the two-phase flow. In the article the results of analyzes of radiometric signal...
Rok 2012
-
Diagnosis of bearing damage in induction motors by instantaneous power analysis
PublikacjaResearch of the machine with simulated bearing damages has been carried out, where variable load torque, simulating bearing damage, was introduced. The results show that components which can be used for bearings diagnosis appear in the spectrum of the product of current and supply voltage instantaneous values. These components are easier to identify than the components of current spectrum, which have been used so far in diagnostic...
Rok 2003
-
Diagnostics of induction motors by means of current supplying measurements
PublikacjaSkładowe prądu zasilającego silnik, które związane są z uszkodzeniami łożysk są małe w porównaniu z dominującą składową sieciową. Zaproponowano układ pomiarowy do ich pomiaru i przedstawiono wyniki badań diagnostycznych na obiektach rzeczywistych.
Rok 2021
-
Direct spectrum detection based on Bayesian approach
PublikacjaThe paper investigates the Bayesian framework's performance for a direct detection of spectrum parameters from the compressive measurements. The reconstruction signal stage is eliminated in by the Bayesian Compressive Sensing algorithm, which causes that the computational complexity and processing time are extremely reduced. The computational efficiency of the presented procedure is significantly...
-
EVALUATION OF LIQUID-GAS FLOW IN PIPELINE USING GAMMA-RAY ABSORPTION TECHNIQUE AND ADVANCED SIGNAL PROCESSING
PublikacjaLiquid-gas flows in pipelines appear in many industrial processes, e.g. in the nuclear, mining, and oil industry. The gamma-absorption technique is one of the methods that can be successfully applied to study such flows. This paper presents the use of thegamma-absorption method to determine the water-air flow parameters in a horizontal pipeline. Three flow types were studied in this work: plug, transitional plug-bubble,...