Publikacje
Filtry
wszystkich: 4399
wyświetlamy 1000 najlepszych wyników Pomoc
Katalog Publikacji
Rok 2020
-
Thermal failure of a second rotor stage in heavy duty gas turbine
PublikacjaThe impulse mode of operation and the supply of various types of fuels causes frequent failures even in the heavy duty gas turbines. The paper presents the ravages of second rotor stage failure in a gas turbine. The excessive thermal elongation rise caused by fuel change was indicated as the main cause. We applied nonlinear numerical analysis, preceded by thermodynamic calculations of the turbine and visual inspection of the effects...
-
Thermochemical Conversion of Biomass and Municipal Waste into Useful Energy Using Advanced HiTAG/HiTSG Technology
PublikacjaAn advanced thermal conversion system involving high-temperature gasification of biomass and municipal waste into biofuel, syngas or hydrogen-rich gas is presented in this paper. The decomposition of solid biomass and wastes by gasification is carried out experimentally with a modern and innovative regenerator and updraft continuous gasifier, among others. A ceramic high-cycle regenerator provides extra energy for the thermal conversion...
-
Thermohydraulic maldistribution reduction in mini heat exchangers
PublikacjaA detailed numerical investigation has been carried out to analyze the flow maldistribution in 50 parallel 1 mm × 1 mm rectangular minichannels and 1 mm depth minigap section with rectangular, trapezoidal, triangular or concave manifolds in Z-type flow configuration. The working medium was ethanol and the mass flow rate was 5 × 10−4 kg/s. Both sections were heated from the bottom side. Heat flux of 10 000 W/m2 and 5000 W/m2 was...
-
Thickness accuracy of sash gang sawing
PublikacjaThin lamellae, corresponding to the layer components of structural glued members, i.e. 2-ply or 3-ply glued parquet, can be manufactured in re-sawing operations of kiln-dried wood blocks. These must be prepared with high dimensional accuracy and adequate surface quality following specific technical requirements for lamellae thickness variations, especially in the upper layers of the glued composite parquet. The accuracy of oak...
-
Tool Wear Prediction in Single-Sided Lapping Process
PublikacjaSingle-sided lapping is one of the most effective planarization technologies. The process has relatively complex kinematics and it is determined by a number of inputs parameters. It has been noted that prediction of the tool wear during the process is critical for product quality control. To determine the profile wear of the lapping plate, a computer model which simulates abrasive grains trajectories was developed in MATLAB. Moreover,...
-
Towards Improving Optimised Ship Weather Routing
PublikacjaThe aim of the paper is to outline a project focusing on the development of a new type of ship weather routing solution with improved uncertainty handling, through better estimation of ship performance and responses to sea conditions. Ensemble forecasting is considered to take into account the uncertainty levels that are typical of operations in a stochastic environment. Increased accuracy of weather prediction is achieved through...
-
Underwater in situ local heat treatment by additional stitches for improving the weldability of steel
PublikacjaIn this paper the influence of in situ local heat treatment performed by additional stitches on the weldability of high-strength low-alloy (HSLA) S355J2C+N steel was tested. The investigated steel is characterized by high susceptibility to cold cracking. It is necessary to find a method to improve the quality of welded joints. The local heat treatment was applied as an eect of bead-on plate welding made on the face of a Tekken...
-
Underwater Local Cavity Welding of S460N Steel
PublikacjaIn this paper, a comparison of the mechanical properties of high-strength low-alloy S460Nsteel welded joints is presented. The welded joints were made by the gas metal arc welding (GMAW)process in the air environment and water, by the local cavity welding method. Welded joints were testedfollowing the EN ISO 15614-1:2017 standard. After welding, the non-destructive—visual, penetrant,radiographic, and ultrasonic (phased array) tests...
-
Unlocking creativity with new technologies
PublikacjaArtificial intelligence, augmented and virtual reality, Internet of Things and digital twins are just a few concepts related to the fourth industrial revolution that is happening right before our eyes. The key question asked by managers in the aerosol sector recently is: what does all this new technology mean to me?
-
Using Moodle as a Solution to Interdisciplinary E-collaboration Issues
PublikacjaRapid technological development in recent years has contributed to numerous changes in many areas of life, including education and communication. Establishing interdisciplinary collaboration brings many benefits, however, it is often associated with numerous problems and inconveniences, as well as the need of constant improvement, lifelong learning, professional development (CPD) and finding an effective way of information transferring....
-
Wavelet Transform Analysis of Heart Rate to Assess Recovery Time for Long Distance Runners
PublikacjaThe diagnostics of the condition of athletes has become a field of special scientific interest and activity. The aim of this study was to verify the effect of a long (100 km) run on a group of runners, as well as to assess the recovery time that is required for them to return to the pre-run state. The heart rate (HR) data presented were collected the day before the extreme physical effort, on the same day as, but after, the physical...
-
Wear of electroplated diamond tools in lap-grinding of Al2O3 ceramic materials
PublikacjaCurrent development of modern products, together with ever-increasing demands for their operation and usage, necessitate the search for new processing methods. Abrasive machining is widely used in many industrial areas, especially for processing difficult-to-machine materials such as advanced ceramics. Grinding with lapping kinematics, also called lap-grinding, is still one of the innovative methods of abrasive processing being...
-
Wear Resistance Enhancement of Al6061 Alloy Surface Layer by Laser Dispersed Carbide Powders
PublikacjaIn this paper, results of the experimental study on improving wear resistance in sliding friction of Al-based alloy are presented. The technique used involves the formation of a metal matrix composite (MMC) in the alloy surface layer by laser dispersion of carbide powders such as WC, TiC and SiC. For WC and TiC MMC surface coatings fabricated under conditions typical for most of the technologically relevant solid-state lasers (wavelength...
-
Wodór jako paliwo cz. 1
PublikacjaW artykule przedstawiono wodór jako nowoczesny nośnik energii oraz jego zastosowanie techniczne w ujęciu konwersji energii. Przybliżono jego odkrycie, właściwości oraz jego wykorzystanie od odkrycia do współczesności. Dokonano opisu budowy i zasady działania ogniw paliwowych. Omówiono ich podział przedstawiając zalety i wady każdego rozwiązania oraz ich zastosowanie techniczne w zależności od typu ogniwa.
-
Wodór jako paliwo cz. 2
PublikacjaW artykule scharakteryzowano aktualne i przyszłościowe metody wytwarzania wodoru. Przedstawiono problem związany z przechowywaniem wodoru oraz ukazano aktualne i przyszłościowe rozwiązania dotyczące magazynowania wodoru.
-
Wpływ rozmieszczenia elementów w separatorach na warunki kinematyczne docierania jednotarczowego
PublikacjaPrzedstawiono wyniki analiz kinematyki docierania elementów płaskich na docierarkach jednotarczowych o standardowym układzie wykonawczym. Określono wpływ rozmieszczenia elementów obrabianych w separatorach na zmienność prędkości docierania.
-
Wpływ rozmieszczenia elementów w separatorach na warunki kinematyczne docierania jednotarczowego
PublikacjaW rozdziale monografii naukowej przedstawiono wyniki analiz kinematyki docierania elementów płaskich na docierarkach jednotarczowych o standardowym układzie wykonawczym. Określono wpływ rozmieszczenia elementów obrabianych w separatorach na zmienność prędkości docierania. W przeprowadzonej symulacji wykorzystano wybrane modele docierarek firmy Kemet, analizując obróbkę dwóch elementów o zróżnicowanych wymiarach gabarytowych i zarysie...
-
Wstępne wyniki projektu GDArms - odtwarzanie środowiska rakiety kosmicznej
PublikacjaW trakcie wynoszenia na ładunek rakiety działają przyspieszenia, drgania, przepływ ciepła oraz zmiany ciśnienia atmosferycznego. Według aktualnych norm i standardów, przed lotem testy środowiskowe są wykonywane sekwencyjnie. Autorzy przedstawili projekt urządzenia do odtwarzania środowiska rakiety kosmicznej. Urządzenie zostało zbudowane na bazie gotowego wzbudnika elektrodynamicznego. Zaprojektowano układy sterowania układów:...
-
WYBRANE ASPEKTY ZMĘCZENIOWYCH USZKODZEŃ OKRĘTOWYCH WAŁÓW NAPĘDOWYCH
PublikacjaProblem zmęczeniowego pękania konstrukcji okrętowych w sposób istotny dla eksploatacji tychże obiektów ujawnił się na przełomie lat 70. i 80. ubiegłego stulecia. Ponieważ pęknięcia zmęczeniowe dotyczą głównie kadłubów statków i są szczególnie dotkliwe dla dużych jednostek (zbiornikowców, masowców i kontenerowców), dlatego też cała uwaga towarzystw klasyfikacyjnych i biur projektowych skupia się głównie na tym aspekcie uszkodzeń...
-
X-RAY DIFFRACTION STUDY OF BISMUTH LAYER-STRUCTURED MULTIFERROIC CERAMICS
PublikacjaGoal of the present research was to apply a solid state reaction route to fabricate bismuth layer-structured multiferroic ceramics described with the formula Bi5FeTi3O15 and reveal the influence of processing conditions on its crystal structure and phase composition. Simple oxide powders Bi2O3, TiO2 and Fe2O3 were used to fabricate Aurivillius-type bismuth layer-structured ferroelectrics. Pressureless sintering in ambient air was...
-
Zabytkowy zespół dwóch podziemnych zbiorników wody czystej i ogrodu wodnego przy dawnym Szpitalu Miejskim w Gdańsku – obecnie Gdański Uniwersytet Medyczny
PublikacjaW pracy opisano mało dotychczas znany fragment zespołu Szpitala Miejskiego w Gdańsku (dziś GUMed, dawniej też Akademia Medyczna), obejmujący dwa historyczne podziemne zbiorniki wody pitnej z początku XX wieku, oraz założenie parkowe z lat 40., powiązane z nimi funkcjonalnie i tworzące spójny zespół. Najpóźniej na przełomie lat 60/70 wykorzystanie tego obszaru (około 1 ha) wygasło i nie został on ponownie zagospodarowany w szerszej...
-
Zintegrowany Program Rozwoju Politechniki Gdańskiej – Moduł 1. Poprawa jakości kształcenia na studiach stacjonarnych II stopnia
PublikacjaPolitechnika Gdańska realizuje od 1 kwietnia 2018 roku projekt „Zintegrowany Program Rozwoju Politechniki Gdańskiej” (POWER 3.5) dofinansowywany ze środków Unii Europejskiej z Europejskiego Funduszu Społecznego w ramach Programu Operacyjnego „Wiedza Edukacja Rozwój”. W artykule zostały przedstawione informacje dotyczące realizacji zadań szczegółowych modułu 1, będącego pierwszym zadaniem z trzech określonych w projekcie. Artykuł...
-
Zmodyfikowana metoda redukcji drgań podczas frezowania przedmiotów wielkogabarytowych narzędziami wieloostrzowymi
PublikacjaW pracy zaprezentowano zmodyfikowaną metodę doboru sztywności zamocowania przedmiotu wielkogabarytowego do stołu obróbkowego, mającą na celu redukcję poziomu drgań względnych narzędzie-przedmiot obrabiany podczas frezowania czołowego narzędziem wieloostrzowym. Przedmiotowa modyfikacja polega na rozwinięciu opracowanej wcześniej metody wyznaczania optymalnego docisku zamocowania w ten sposób, że pracę sił skrawania na kierunku szerokości...
Rok 2019
-
A hybrid model of flooding of the ro-ro ships in damaged conditions
PublikacjaThe paper presents some results on investigations concerning development of a hybrid model for assessment of performance of the ro‐ro ships in damaged conditions. The model is devoted towards assessing the performance of the damaged ro‐ro ships at the preliminary stage of design. The key problems associated with preparing of such the model are associated with working out a method of assessment of the damaged roro ships performance,...
-
A model development and experimental verification for a vapour microturbine with a permanent magnet synchronous generator
PublikacjaVapour microturbines with permanent magnet synchronous generators are implemented in micropower plants for dispersed power generation systems. The dynamic model of such a microturbine set was developed and presented. The developed relations result from the generic equations. Experimental data for two different working medium were used for model verification. A microturbine set model was tested during the changes in the parameters...
-
A New Rehabilitation Device for Balance Impaired Individuals
PublikacjaIn the paper authors present a device designed to improve the rehabilitation process of people with balance impairment. The discussed device (JStep) utilizes a commercially available static standing frame (stander) modified in order to fit force sensing units under the feet and in the pillows around the hips of a patient. While executing rehabilitation tasks, the patient may compensate his balance deficiency by leaning on the pillows...
-
A numerical analysis of the thermal effects in the jet impingement stagnation zone
PublikacjaMost of the flows occurring in the engineering systems are turbulent and their accurate numerical analysis is still challenging, especially when combined with the heat transfer. One of the methods of heat transfer enhancement is utilization of the turbulent impinging jets, which were recently applied also in the heat exchangers. Their positive impact on the heat transfer performance was proven, but many questions related to its...
-
A SEARCH OF AN INDUCER GEOMETRY THAT IS BENEFICIAL FOR LIFTING PARAMETERS OF A LIFTED OBJECT OF A SELECTED SHAPE
PublikacjaThe literature describes acoustic levitation phenomena with the utilization of air squeeze film between the vibrating inducer and the lifted object. The objective of the study is to determine the shape of the inducer with vibration characteristics that would allow the levitation of an object of the assumed geometry. In this paper, the influence of the dimension ratio of the inducer on the frequency of the first mode of vibration...
-
A semi-empirical model for flow boiling heat transfer with account of the reduced pressure effect
PublikacjaIn the present study the attention was focused on the influence of reduced pressure on the predictions of heat transfer during flow boiling at the extensive range of pressures. The results of calculations were to test the sensitivity of the in-house flow boiling model with respect to the selection of the appropriate two-phase flow multiplier, which is one of the distinctive elements of that model. For this purpose a few two-phase...
-
A study of a compact high-efficiency zero-emission power plant with oxy-fuel combustion
PublikacjaThis paper discusses the application of global trends in gas cycles technology using oxy-fuel combustion. This is followed by a demonstration of a design solution for a new cycle with two enhanced energy-converting devices, namely a wet combustion chamber and a spray-ejector condenser. The proposed gas and steam cycle unit is contained within a single turbine, whose benefits combine those offered by gas turbines (high inlet temperatures)...
-
A unified approach to the analysis of electric energy and fuel consumption of cars in city traffic
PublikacjaForecasting fuel and electricity consumption is an important factor determining the direction of changes in road engineering solutions, traffic management, selection of routes for public transport and development more efficient car drive systems. With a reliable and easy-to-use computational tool, it is possible to reduce the consumption of primary energy sources and reduce the emission of toxic compounds in cities. An analysis...
-
Advantages of the Application of the Temper Bead Welding Technique During Wet Welding
PublikacjaThermo-mechanically rolled S460ML steel was chosen for welding in underwater wet welding conditions by covered electrodes. The main aim of this study was to check the weldability for fillet welds in a water environment by controlled thermal severity (CTS) tests and to check the influence of temper bead welding (TBW) on the weldability of the investigated steel. Non-destructive and destructive tests showed that S460ML steel has...
-
Akustyczne zobrazowanie morskich osadów dennych
PublikacjaPrzedstawiany temat rozprawy doktorskiej: „Akustyczne zobrazowanie morskich osadów dennych”, prezentuje metody zobrazowania struktury osadów dennych pozyskanych z sondowania akwenu echosondą parametryczną SES-2000 Standard oraz urządzeniami pomocniczym — echosondą wielowiązkową EM3002 i sonarem bocznym. Tezą jest wykazanie, że metody akustyczne dają możliwość bezinwazyjnej klasyfikacji osadów dennych. Hipoteza zakłada, że istnieje...
-
Algorytmy roju w modelowaniu MES, czyli jak stado szpaków może pomóc inżynierowi
PublikacjaW poprzednich numerach „Pisma PG” prof. Jacek Rumiński przedstawił możliwości i perspektywy rozwoju sztucznej inteligencji (SI), zwłaszcza w kontekście notujących obecnie liczne sukcesy sztucznych sieci neuronowych. Jednak nie tylko budowa układu nerwowego jest inspiracją dla nowych metod SI. Ciekawą grupą metod są algorytmy wzorujące się na zachowaniu zwierząt, zwłaszcza na ich zdolnościach socjalnych i współpracy przy stawianiu...
-
An energetic analysis of a gas turbine with regenerative heating using turbine extraction at intermediate pressure - Brayton cycle advanced according to Szewalski's idea
PublikacjaIn this paper, a modification of a simple gas turbine into the Brayton cycle with regenerative heating, using turbine extraction at intermediate pressure, is presented. The main concept of the retrofitting is based on the transfer of heat from the turbine exhaust gases to the air entering the combustion chamber. The extracted gas transfers heat to air via the divided regenerative heat exchanger and after that is compressed and...
-
An improved method for flow boiling heat transfer with account of the reduced pressure effect
PublikacjaIn the paper are presented the results using the authors own model to predict heat transfer coefficient during flow boiling. The model has been tested against a large selection of experimental data to investigate the sensitivity of the in-house developed model. In the work are presented the results of calculations obtained using the semi-empirical model on selected experimental flow boiling data of the refrigerants: R134a, R1234yf,...
-
An Influence of Factors of Flow Condition, Particle and Material Properties on Slurry Erosion Resistance
PublikacjaThe degradation of materials due to slurry erosion is the serious problem which occurs in the power industries. The paper presents actual knowledge about an influence of individual factors connected with flow conditions, particles and material properties on the slurry erosion resistance. Among the factors connected with operating conditions, an influence of impact angle, and velocity of impact, particle concertation and liquid...
-
Analiza siłowni nadkrytycznych oraz ultranadkrytycznych
PublikacjaNiniejszy artykuł zawiera przegląd istniejących rozwiązań siłowni nadkrytycznych oraz ultra nadkrytycznych. Przedstawiono historię rozwoju bloków na parametry nadkrytyczne. Obecny stan technologii został zaprezentowany – są to następujące parametry pary świeżej: 650°C oraz 330 bar. W Polsce istnieje 8 bloków pracujących na parametry nadkrytyczne. Ich parametry pracy zostały przedstawione w tekście. Z kolei elektrownią parową posiadającą...
-
Analiza stosowania uchwytów modułowych i specjalnych w operacjach obróbkowych.
PublikacjaPrzedstawiono konstrukcje i montaż zaprojektowanych uchwytów modułowych i specjalnych. Analizowano uchwyty dla wybranych operacji obróbki dźwigni i korpusu. Wyznaczono również koszt uchwytów dla tego samego typu obrabianego elementu. Zastosowana metodyka może być stosowana między innymi w procesie kształcenia inżynierskiego mechaników technologów.
-
Analiza techniczna funkcjonalności pilarki PZS-350. Ekspertyza techniczna opracowana na zlecenie REMA S.A.
PublikacjaWykonana ekspertyza techniczna dotyczyła prototypowej pilarki tarczowej PZS-350 przeznaczonej do cięcia surowej sklejki drzewnej na arkusze o żądanym wymiarze. Celem była analiza funkcjonalności wykonanego prototypu oraz jego zgodności z przyjętymi założeniami technicznymi. Główne funkcje realizowane przez pilarkę obejmują: a) transport sklejki ze stołu podawczego do cięcia wzdłużnego; b) cięcie wzdłużne i usuwanie odpadu po tym...
-
Analiza układów kinematycznych docierania powierzchni płaskich w aspekcie równomierności zużycia tarczy docierającej
PublikacjaPrzedmiotem rozprawy doktorskiej jest analiza układów kinematycznych docierania jednotarczowego w aspekcie równomierności zużycia tarczy docierającej. W pierwszej części pracy szczegółowo opisano mechanizm docierania powierzchni płaskich oraz określono wpływ poszczególnych parametrów procesu na dokładność obróbki. Przeanalizowano dotychczas opracowane modele zużycia docieraka oraz opisano istniejące rozwiązania konstrukcyjne układów...
-
Analiza zmienności generacji energii elektrycznej w okresie pierwszych pięciu miesięcy 2019 r. ze szczególnym uwzględnieniem generacji energii ze źródeł wiatrowych
PublikacjaW artykule przedstawiono zagadnienia związane z szeroko pojętym rozwojem energetyki wiatrowej. Omówiono stan rozwoju energetyki wiatrowej na świecie. Na podstawie dostępnych badań przybliżono także zagadnienia związane z czynnikami wpływającymi na rozwój odnawialnych źródeł energii oraz ich oddziaływanie na środowisko naturalne. Główny nacisk położono jednakże na analizę zjawisk w pracy Krajowego Systemu Elektroenergetycznego (KSE)...
-
ANALYSIS OF BONE WEDGE DIMENSIONS SELECTION METHODS IN HIGH TIBIAL OSTEOTOMY
PublikacjaThe article presents the analysis of methods for selecting dimensions of bone wedge for high tibial osteotomy. The existing methods are described along with the procedure. In the following paragraphs, deficiencies in the selection of bone wedge dimensions and global trends in this field have been demonstrated. Based on the numerical analysis, the problem appearing in the wrong choice of bone wedge imensions was illustrated.
-
Analysis of ring cracks in ceramic rolling elements using the boundary element method
PublikacjaCeramic materials have been increasingly used in bearing technology for over a dozen years. This is due to the characteristic properties of ceramic materials such as: high hardness, corrosion resistance, the possibility of use in aggressive chemical environments, as well as due to the lower specific weight compared to steel materials. However, the use of ceramic materials is connected with many limitations. The main disadvantages...
-
Analysis of size and shape of abrasive micrograins in lapping of assembly joints
PublikacjaPrzedstawiono skomputeryzowana analizę wielkości i kształtu mikroziaren ściernych. W badaniach mikroziaren węglika boru, węglika krzemu i elektrokorundu zastosowano mikroskopie optyczna oraz specjalistyczne oprogramowanie MultiScan v.6.08
-
Analysis of start energy of Stirling engine type alpha
PublikacjaThe Stirling engine type alpha is composed of two cylinders (expansion space E and compression space C), regenerator that forms the space between the cylinders and the buffer space (under the pistons). Before the start-up and as a result of long-term operation, the average pressure in the working space (above the pistons) and in the buffer space is the same. However, in the initial phase of operation, the average pressure in the...
-
Analysis of the regenerative braking process for the urban traffic conditions
PublikacjaIn a regular drive system, with an internal combustion engine, vehicle braking is connected with the unproductive dissipation of kinetic and potential energy accumulated in the mass of the vehicle into the environment. This energy can constitute up to 70% of the energy used to drive a vehicle under urban conditions. Its recovery and reuse is one of the basic advantages of hybrid and electric vehicles. Modern traffic management...
-
Antibacterial Activity and Cytocompatibility of Bone Cement Enriched with Antibiotic, Nanosilver, and Nanocopper for Bone Regeneration
PublikacjaBacterial infections due to bone replacement surgeries require modifications of bone cement with antibacterial components. This study aimed to investigate whether the incorporation of gentamicin or nanometals into bone cement may reduce and to what extent bacterial growth without the loss of overall cytocompatibility and adverse effects in vitro. The bone cement Cemex was used as the base material, modified either with gentamicin...
-
Application of nanofluids in thermal technologies
PublikacjaNanofluids it is a relatively new category of thermal fluids that can serve as coolants, both in single- and two phase systems. However application of nanofluids in industrial applications requires faultless their thermophysical properties. Existing models originally developed for liquid/solid particles mixtures (slurries) fail in case of nanofluids. Moreover correlations used to calcuate heat transfer coefficients of conventional...
-
Application of Reverse Engineering Technology in Part Design for Shipbuilding Industry
PublikacjaIn the shipbuilding industry, it is difficult to create CAD models of existing or prototype parts, especially with many freeform surfaces. The paper presents the creation of the CAD 3D model of a shipbuilding component with the application of the reverse engineering technology. Based on the data obtained from the digitization process, the component is reconstructed in point cloud processing programs and the CAD model is created....