Wyszukiwarka
Zakład Konstrukcji Maszyn i Inżynierii Medycznej
Publikacje
Filtry
wszystkich: 477
Katalog Publikacji
Rok 2020
-
Determination of the theoretical and actual working volume of a hydraulic motor
PublikacjaA new methodology of determination of the theoretical and actual working volume of a hydraulic motor based on the characteristics of the delivered flow rate into hydraulic motor vs. the rotational speed at a constant pressure drop in the working chambers is described in this paper. A new method of describing the delivered flow rate into a motor per one shaft revolution as a nonlinear function of the pressure drop in the motor working...
-
Stress Monitoring System for Individuals with Autism Spectrum Disorders
PublikacjaIn this article, a stress monitoring system tailored for individuals with Autism Spectrum Disorders (ASD) and developed for the educational institution is presented. People with ASD face problems with effective stress management due to their high self-perceived levels of stress, poor ability to cope with it, and dificulties with the accurate detection of the source of stress. Consistently, being able to measure stress appears to...
-
Technologia wytwarzania opakowań PET dla produktów wrażliwych
PublikacjaW artykule przedstawiono nowoczesne, liniowe maszyny rozdmuchowe przeznaczone do wytwarzania opakowań (butelek) PET metodą rozdmuchu z preform. Opisano systemy umożliwiające zmniejszenie zużycia energii elektrycznej niezbędnej do wytworzenia jednego opakowania PET.
-
Test Stand for Multi-option Stretching of Soft Tissues
PublikacjaThe paper presents the genesis of the design and possibilities of the test stand for stretching soft tissues as well as examples of tests carried out on this device.
-
Test Stand for Multi-option Stretching of Soft Tissues
PublikacjaThe paper presents the genesis of the design and possibilities of the test stand for stretching soft tissues as well as examples of tests carried out on this device.
-
The Impact Of The Selected Parameters Of Fdm Manufacturing Technology On Tribological Performance Of Abs–Steel Pair Under Dry Friction
PublikacjaThe paper presents the result of tribological test of ABS and steel samples sliding under dry friction. Polymeric samples were manufactured of ABS material using FDM technology. Testing was carried out in unidirectional sliding in a ring-on-flat contact in a PT-3 tribometer. The scope of tested parameters included volumetric and mass wear, the friction coefficient, and polymeric specimen temperature. Polymeric specimens used in...
-
The Influence of Water and Mineral Oil on Mechanical Losses in a Hydraulic Motor for Offshore and Marine Applications
PublikacjaIn this paper, mechanical losses in a hydraulic motor supplied with water and mineral oil (two liquids having significantly different viscosity and lubricating properties) are described and compared. The experimental tests were onducted using a special design (prototype) of a hydraulic satellite motor. The design of the satellite motor is presented. This motor was developed to supply both with water and mineral oil and features...
-
Wear Resistance Enhancement of Al6061 Alloy Surface Layer by Laser Dispersed Carbide Powders
PublikacjaIn this paper, results of the experimental study on improving wear resistance in sliding friction of Al-based alloy are presented. The technique used involves the formation of a metal matrix composite (MMC) in the alloy surface layer by laser dispersion of carbide powders such as WC, TiC and SiC. For WC and TiC MMC surface coatings fabricated under conditions typical for most of the technologically relevant solid-state lasers (wavelength...
Rok 2019
-
A SEARCH OF AN INDUCER GEOMETRY THAT IS BENEFICIAL FOR LIFTING PARAMETERS OF A LIFTED OBJECT OF A SELECTED SHAPE
PublikacjaThe literature describes acoustic levitation phenomena with the utilization of air squeeze film between the vibrating inducer and the lifted object. The objective of the study is to determine the shape of the inducer with vibration characteristics that would allow the levitation of an object of the assumed geometry. In this paper, the influence of the dimension ratio of the inducer on the frequency of the first mode of vibration...
-
ANALYSIS OF BONE WEDGE DIMENSIONS SELECTION METHODS IN HIGH TIBIAL OSTEOTOMY
PublikacjaThe article presents the analysis of methods for selecting dimensions of bone wedge for high tibial osteotomy. The existing methods are described along with the procedure. In the following paragraphs, deficiencies in the selection of bone wedge dimensions and global trends in this field have been demonstrated. Based on the numerical analysis, the problem appearing in the wrong choice of bone wedge imensions was illustrated.
-
Analysis of ring cracks in ceramic rolling elements using the boundary element method
PublikacjaCeramic materials have been increasingly used in bearing technology for over a dozen years. This is due to the characteristic properties of ceramic materials such as: high hardness, corrosion resistance, the possibility of use in aggressive chemical environments, as well as due to the lower specific weight compared to steel materials. However, the use of ceramic materials is connected with many limitations. The main disadvantages...
-
Effect of manufacturing errors of the pad sliding surface on the performance of the hydrodynamic thrust bearing
PublikacjaIn the present study, investigation of the effect of manufacturing errors on the performance of large tilting pad thrust bearings has been performed, following a CFD-based Thermohydrodynamic analysis of a single pad. A 3D model has been generated, including the pad, the lubricant film and the corresponding part of the collar. The pad has been assumed to be deformed about the pivot point, due to thrust loading. Manufacturing errors...
-
Experimental investigation into surface texture effect on journal bearings performance
PublikacjaThe aim of this study was to analyse the performance of journal bearings with specially created dimples on the sliding surface and operating under various conditions. The texture was created on the bearing surface that co-acted with the smooth journal; moreover, the variation of the textured surface of the journal mating with the smooth bearing was tested, and the results were compared to those obtained with the standard smooth...
-
Hybrid Finite Element Method Development for Offshore Structures’ Calculation with the Implementation of Industry Standards
PublikacjaIn the design process of offshore steel structures, it is typical to employ commercial calculation codes in which simulationand evaluation of results are performed on the basis of the available standards (e.g. API, DNV, Lloyds). The modelingand solution rely on finite element methods and cover the simulation of the structure’s properties along with the influenceof the marine environment – sea currents, wave...
-
Hybrid Finite Element Method Development for Offshore Structures’ Calculation with the Implementation of Industry Standards
PublikacjaIn the design process of offshore steel structures, it is typical to employ commercial calculation codes in which simulation and evaluation of results are performed on the basis of the available standards (e.g. API, DNV, Lloyds). The modeling and solution rely on finite element methods and cover the simulation of the structure’s properties along with the influence of the marine environment – sea currents, wave and wind loading,...
-
Influence of the low ambient temperature on the start-up process of hydraulic pumps
PublikacjaStarting hydraulic pumps in low ambient temperatures may cause: decreased hydraulic-mechanical efficiency, larger vibration of hydraulic installation, faster wear and more frequent damage to the elements of pumps, change of material properties of elements, increase of pressure drop. As a result of pressure drop in the suction pipe, large underpressure may be experienced, causing incomplete filling of pump working chambers with...
-
Inverse heat transfer problem solution of sounding rocket using moving window optimization
PublikacjaAn Inverse Heat Transfer Problem is solved for a sounding rocket module given its geometry and measured temperature profile. The solution is obtained via moving window optimization, a technique for solving inverse dynamics. An analysis is performed to modify the method to avoid oscillatory behavior of the resulting heat flux profile. The method parameters are tuned in relation to characteristic phases of the flight. Results are...
-
Investigation of the thermal effects in water-lubricated journal bearings with axial grooves
PublikacjaWater-lubricated hydrodynamic journal bearings are frequently applied as stern tube bearings due to their advantages over other bearing types. They are environmentally friendly, can operate without sealings and in conditions of low friction losses. The most popular are bearings with open axial grooves, which require, for proper operation, forced axial flow of the lubricating water. Correctly designed and operated stern tube bearings...
-
Mechanical properties of the human stomach under uniaxial stress action
PublikacjaThe aim of this study was to estimate the range of mechanical properties of the human stomach in order to use the collected data in numerical modelling of surgical stapling during resections of the stomach. The biomedical tests were conducted in a self-developed tensile test machine. Twenty-two fresh human stomach specimens were used for the experimental study of its general strength. The specimens were obtained from morbidly obese...
-
Metodologia badania zaworów hamulcowych
PublikacjaArtykuł opisuje metodologię statycznego i dynamicznego badania zaworów hamulcowych. Stanowisko badawcze zaprojektowano i zbudowano na Politechnice Gdańskiej jako część projektu badawczo-rozwojowego pt.: „Zaprojektowanie i zbadanie innowacyjnych podsystemów ładowarek kołowych firmy Hydro-Metal”, dofinansowanego przez PARP w ramach programu „Bon na innowacje”. Ponadto przedstawiono szczegóły konstrukcyjne i funkcje najczęściej spotykanych zaworów...
-
Powder metallurgy of the porous Ti-13Nb-13Zr alloy of different powder grain size
PublikacjaThe objective of the present project was to determine the effects of powder granulation (fraction of grain size) for the Ti-13Nb-13Zr alloy, produced by powder metallurgy, on its porosity, grain cohesion, compressive strength, and Young`s modulus. Two powder fractions, 45–105 µm, and 106–250 µm were applied. The 50 mass pct of NH4HCO3 was added as a space holder. The specimens were in compaction stage uniaxially pressed at pressure...
-
The influence of water and mineral oil on volumetric losses in the displacement pump for offshore and marine applications
PublikacjaIn this paper volumetric losses in a positive displacement pump supplied with water and mineral oil are described and compared. The experimental tests were conducted using a prototype of a satellite pump (with a non-circular tooth working mechanism). In this paper the sources of volumetric losses in this pump are characterised. On this basis, a mathematical model of these losses has been presented. The results of the calculation...
-
The methodology of design of axial clearances compensation unit in hydraulic satellite displacement machine and their experimental verification
PublikacjaA new methodology of calculating the dimensions of the axial clearance compensation unit in the hydraulic satellite displacement machine is described in this paper. The methods of shaping the compensation unit were also proposed and described. These methods were used to calculate the geometrical dimensions of the compensation field in an innovative prototype of a satellite hydraulic motor. This motor is characterized by the fact...
-
THEORETICAL AND EXPERIMENTAL INVESTIGATION OF THIN-WALLED BEARING SHELL’S DESIGN PARAMETERS AND ASSEMBLY CONDITIONS ON THE HOLDING TORQUE INSIDE A HOUSING BORE OF A CONNECTING ROD
PublikacjaThe aim of the work was the experimental and theoretical evaluation of the influence of the most important parameters determining the holding torque of a thin-walled bearing shell inside a housing bore of a connecting rod. The main investigated parameters were defned by authors experience in this feld. In the frst stage of research, a special test stand was designed in order to allow measuring the real values of the friction torque...
Rok 2018
-
Analiza wytrzymałościowa zmodyfikowanej belki liny łyżkowej zainstalowanej na platformie Lotos Petrobaltic
PublikacjaPrzedmiotem sprawozdania jest analiza wytrzymałosciowa zmodyfikowanej belki liny łyżkowej zainstalowanej na platformie Lotos Petrobaltic. Modyfikacja polega na wykonaniu w belce przelotowego otworu umozliwiającego zamontowanie czujnika napięcia liny łyżkowej.
-
ANALYSIS OF BEARING CLEARANCE AND WIDTH OF OIL GROOVE ON CHARACTERISTIC OF FLUID FILM IN HYDRODYNAMIC MAIN CRANKSHAFT BEARINGS
PublikacjaAbstract Paper represents analysis of influence of oil groove width and bearing clearance on characteristics of oil film in hydrodynamic journal main crankshaft bearing. Analysis was performed in purpose to define influence of bearing clearance and dimensions of oil groove on static characteristics and manufacturability of half shelf bearings in industrial high-volume production. Computer simulations was made using ARTbear program...
-
Analysis of Failures of High Speed Shaft Bearing System in a Wind Turbine
PublikacjaDuring the operation of wind turbines with gearbox of traditional configuration, consisting of one planetary stage and two helical stages high failure rate of high speed shaft bearings is observed. Such a high failures frequency is not reflected in the results of standard calculations of bearing durability. Most probably it can be attributed to atypical failure mechanism. The authors studied problems in 1.5 MW wind turbines of...
-
ANALYSIS OF THE LOAD-CARRYING CAPACITY OF A HYDRODYNAMIC WATER-LUBRICATED BEARING IN A HYDROELECTRIC POwER PLANT
PublikacjaThe paper presents an analysis of the load-carrying capacity of a historic hydrodynamic water-lubricated radial bearing of an unconventional segment design installed in the Braniewo Hydroelectric Power Plant. The aim of the calculations was to determine whether the bearing operates in the conditions of hydrodynamic or mixed lubrication, as well as to establish the optimal geometry of the axial grooves allowing for the highest load-carrying...
-
Determinants of the surface quality, density and dimensional correctness in selective laser melting of the Ti-13Zr-13Nb alloy
PublikacjaSelective laser melting is widely used for custom-designed elements. Successful manufacturing depends on laser treatment parameters and material features. This research aimed to determine the effects of laser power, scan time and hatch distance on surface quality, relative density and dimensional precision for cuboids made of the Ti-13Zr-13Nb alloy. The influence of energy density, energy flux and pre-heating was seen to be decisive...
-
Ecological bearing systems for water turbines – research and development at Gdansk University of Technology
PublikacjaIncreasing requirements for environmental protection make it necessary to introduce new materials and designs. Hydroelectric power plants operating in direct contact with water reservoirs and rivers are potentially endangering water cleanliness, hence they should also be modernized in the way minimizing the environmental hazards. A lot of progress in this field has been achieved in last decades, but still there is much work to...
-
Evaluation of bearing and journal damage in MAN 9L40-54 engines installed on M/V STENA SCANDINAVICA ferry
PublikacjaThe following report was requested by Remontowa Shiprepair Yard (RSY) S.A. in Gdansk ´ (contract no. 4/2018/EX/U, dated 13.02.2018) and prepared based on the materials received from RSY, two on-board inspections and the participation of the contractors in three conferences with RSY representativesi. The goal of the analysis performed by the experts of Gdansk University of Technology was ´ to determine the character of the bearing...
-
EXPERIMENTAL EVALUATION OF DLC/STEEL SLIDING CONTACTS’ OPERATIONAL ENVELOPE
PublikacjaIn an industrial project concerning sliding bearings, a sliding pair was selected of high alloy steel vs. industrial grade DLC coated high alloy steel as a basis for an innovative design of high performance sliding bearings lubricated with a synthetic oil for use in geared transmission units. The development process required credible data on the ultimate resistance of the sliding pair to very high contact stress. An experimental...
-
FEM ANALYSIS AND EXPERIMENTAL TESTS OF RIGID RISER HANGING SYSTEM
PublikacjaThe article presents the analysis, project, and experimental examination of an original rigid riser for Coil Tubing Pipes. The principle of riser operation is based on the use of friction forces. The research included the FEM analysis of the designed riser, calculations of the required bolt tensions, and checking the effect of the clamping force on stress distribution in the pipeline. The results of computer simulation were verified...
-
FEM Calculations in Analysis of Steel Subsea Water Injection Flowlines Designing Process
PublikacjaPaper describes the result of theoretical research aimed at assessing the loads and operating conditions of a Coiled Tubing pipeline injecting water, suspended to the mining platform of Lotos Petrobaltic. For this purpose, appropriate calculation models have been developed using the Finite Element Method (FEM), taking into account the nature of the analyzed object and its loads. The analyzes were carried out for two pipes (previously...
-
Funkcjonowanie zespołów napędu hydraulicznego maszyn w niskich temperaturach otoczenia
PublikacjaW pracy przedstawiono cztery warianty klasyfikacji rozruchów oziębionego napędu hydraulicznego. Pierwsza sytuacja dotyczy zagadnienia, w którym wszystkie zespoły układu napędowego wraz z olejem mają taką samą niską temperaturę podczas rozruchu. Pozostałe warianty odnoszą się do rozruchu w warunkach szoku termicznego wywołanych zasilaniem ciepłym czynnikiem roboczym oziębionych zespołów hydraulicznych. Rozruch zespołów...
-
HYDROSTATIC THRUST BEARING WITH REDUCED POWER LOSSES
PublikacjaIn many cases in rotating machinery, axial load is carried by tilting pad thrust bearings which have been developed since the beginning of 20th century. For high reliability and simplicity, most commonly the bearings are bath lubricated. In the times of sustainable development, however, minimization of friction losses becomes an important criterion for machinery assessment, and a strategic goal of their development. Performed calculations,...
-
Improvement of Thrust Bearing Calculation Considering the Convectional Heating within the Space between the Pads
PublikacjaA modern thrust bearing tool is used to estimate the behavior of tilting pad thrust bearings not only in the oil film between pad and rotating collar, but also in the space between the pads. The oil flow in the space significantly influences the oil film inlet temperature and the heating of pad and collar. For that reason, it is necessary to define an oil mixing model for the space between the pads. In the bearing tool, the solutions...
-
OPINIA TECHNICZNA nr 3/PG/mosty Sprawowanie nadzoru naukowo-technicznego podczas opracowywania projektów obiektów hydrotechnicznych, mostowych i drogowych w ramach realizacji przedsięwzięcia pn. „Budowa drogi wodnej łączącej Zalew Wiślany z Zatoka Gdańską” Opinia nt. rozwiązań technicznych przedstawionych w projekcie budowlanym przekopu w lokalizacji Nowy Świat - branża mostowa
PublikacjaOpinię przygotowano w ramach prowadzonego nadzoru naukowo-technicznego podczas opracowywania projektów obiektów hydrotechnicznych, mostowych i drogowych w ramach realizacji przedsięwzięcia pn. „Budowa drogi wodnej łączącej Zalew Wiślany z Zatoka Gdańską”.
-
OPINIA TECHNICZNA nr 5/PG/mosty Sprawowanie nadzoru naukowo-technicznego podczas opracowywania projektów obiektów hydrotechnicznych, mostowych i drogowych w ramach realizacji przedsięwzięcia pn. „Budowa drogi wodnej łączącej Zalew Wiślany z Zatoka Gdańską” Opinia nt. rozwiązań technicznych przedstawionych w projekcie wykonawczym przekopu w lokalizacji Nowy Świat - branża mostowa
PublikacjaOpinię przygotowano w ramach prowadzonego nadzoru naukowo-technicznego podczas opracowywania projektów obiektów hydrotechnicznych, mostowych i drogowych w ramach realizacji przedsięwzięcia pn. „Budowa drogi wodnej łączącej Zalew Wiślany z Zatoka Gdańską”.
-
OPINIA TECHNICZNA nr 8/PG/mosty Sprawowanie nadzoru naukowo-technicznego podczas opracowywania projektów obiektów hydrotechnicznych, mostowych i drogowych w ramach realizacji przedsięwzięcia pn. „Budowa drogi wodnej łączącej Zalew Wiślany z Zatoka Gdańską” Opinia uzupełniająca do 5/PG/mosty w zakresie mechanizmów zastosowanych na przekopie po przedstawieniu przez projektanta wyciągu z obliczeń
PublikacjaOpinię przygotowano w ramach prowadzonego nadzoru naukowo-technicznego podczas opracowywania projektów obiektów hydrotechnicznych, mostowych i drogowych w ramach realizacji przedsięwzięcia pn. „Budowa drogi wodnej łączącej Zalew Wiślany z Zatoka Gdańską”.
-
Opracowanie opinii, zwanej dalej pracą, o zgłoszeniu patentowym nr 418605 z dnia 08.09.2016 zatytułowanym „Maszyna wyporowa obiegowo-krzywkowa zwłaszcza silnik hydrauliczny”.
PublikacjaOpracowano opinię o zgłoszeniu patentowym nr P.418605 z dnia 08.09.2016r. zatytułowanym „Maszyna wyporowa obiegowo-krzywkowa, zwłaszcza silnik hydrauliczny”.
-
Prace rozwojowe nad pierwszą polską ładowarką teleskopową
PublikacjaW artykule dokonano przeglądu prac wykonanych przez członków Zespołu Hydrauliki i Pneumatyki Wydziału Mechanicznego Politechniki Gdańskiej w ramach programu „Bon na innowacje” dla firmy „Hydro-Metal Adam Gordziejczyk”. Obiektem prac była ładowarka teleskopowa z napędem hydraulicznym o udźwigu 1,5 T. Pierwsza część prac polegała na obliczeniach MES i poprawie sztywności konstrukcji ramy i wysięgnika. Druga część prac polegała na...
-
Rehabilitation device supporting active and passive upper limb exercises
PublikacjaThis article presents a mechatronic solution for rehabilitation devices supporting active and passive exercises in persons with motor dysfunctions of the upper limbs in the area of the elbow and shoulder joints. A planar positioner integrated with original software and a control system, served as the basis for creating the present solution. Bellman’s programming method was applied to optimize the motion trajectory of the planar...
-
Results from tests on bolted connection components for evaluation of friction coefficient in various contact conditions
PublikacjaThe main purpose of the work was the analysis and evaluation of the self-locking quality of a bolted joint covered with Xylan 1070 coating, with comparison to the classic bolts lubricated with Molykote compound during assembly. The second part of the work was the verification of the compliance of the bolts and nuts used in the installation with the ASME B1.1 norm.
-
The Application of Vibration Recording and Analysis in Tribological Research on Sliding Friction
PublikacjaThe paper reports on a tribological research on the macroscopic manifestation and characteristics of sliding friction. The aim of the task was to measure friction in lubricated sliding contacts and test the interactions between the environment (the test rig) and the experimental friction contact. Friction-induced vibrations were observed and studied as a manifestation of the process. The typical set of velocity and force/torque...
-
THE INFLUENCE OF WATER AND MINERAL OIL ON MECHANICAL LOSSES IN THE DISPLACEMENT PUMP FOR OFFSHORE AND MARINE APPLICATIONS
PublikacjaIn this paper mechanical losses in a positive displacement pump supplied with water and mineral oil (two liquids having significantly different viscosity and lubricating properties) are described and compared. The experimental tests were conducted using a special design (prototype) of a satellite pump. The design of the satellite pump is presented in the article. The pump features a non-circular tooth working mechanism. This pump...
-
The use of plate springs for preloading of a system of tapered roller bearings of a wind turbine gearbox
PublikacjaThe use of preloaded tapered roller bearings in wind turbine drive systems allows a transfer of load in the case of high variations of axial forces. The examined bearing system, a modification of a current design, consists of a pair of different sized bearings. Previous study showed the high sensitivity of tapered roller bearings on the existing radial interference. Dimensional tolerances used in the original design do not allow...
-
Zagadnienia tribologiczne w hamulcu silnika hydraulicznego
PublikacjaPrzedmiotem badań był prototypowy hamulec cierny wielopłytkowy do silnika satelitowego SM-0,6 o teoretycznej objętości roboczej 16,7 cm3/obr. Hamulec ten zbudowany był z 27 tarcz ciernych wykonanych z materiału TOLOX oraz z pakietu sprężyn talerzowych zamontowanych w układzie X. Zablokowanie hamulca następuje w skutek siły docisku pakietu sprężyn talerzowych płytek ciernych co następuje w chwili spadku ciśnienia w komorze tłoka...
Rok 2017
-
3D Printing of Metallic Implants
PublikacjaThe fabrication of various elements, solid and open porous structures of stainless steel and Ti alloy is described. The process was started with the design of 3D models in CAD/CAM system. The 3D models were transformed into *.stl files and then the manufacturing process of the real structures by means of the selective laser melting with the SLM Realizer 100 3D printer was made. The paper shows the porous specimens made for possible...
-
Extended duration running and impulse loading characteristics of an acoustic bearing with enhanced geometry
PublikacjaThis paper presents performance during prolonged running of the acoustic bearing when PZTs are switched off and when they are switched on. The effect of active PZT on shaft’s displacements in X and Y directions is clearly demonstrated. Performance of the acoustic bearing was also assessed when an impulse force was applied to the running shaft at speed. Once again the benefits of having PZTs active are beyond doubt. The instability...