Search results for: FLOW PATTERN LATTICE-GAS AUTOMATON
-
Influence of soil anisotropic stiffness on the deformation induced by an open pit excavation.
PublicationIn this paper, the problem of deformation induced by an open pit excavation in anisotropic stiff soils is analysed by FE modelling. The presented research is focused on the influence of material model with anisotropic stiffness on the accuracy of deformation predictions as compared with the field measurements. A new hyperelastic-plastic model is applied to simulate anisotropic mechanical behaviour of stiff soils. It is capable...
-
Natural convection in symmetrically heated vertical channels
PublicationThe study describes natural convection through a vertical channel, open on four sides and bound by two isothermal walls. Both balancing and infrared experimental investigations were performed in air (Pr = 0.71) to estimate the impact of channel width s and wall-to-ambient temperature difference (tw - t∞) on natural convective heat transfer, the formation of air flow patterns and the rate of flow pattern formation. The study was...
-
RANS-based design optimization of dual-rotor wind turbines
PublicationPurpose An improvement in the energy efficiency of wind turbines can be achieved using dual rotors. Because of complex flow physics, the design of dual-rotor wind turbines (DRWTs) requires repetitive evaluations of computationally expensive partial differential equation (PDE) simulation models. Approaches for solving design optimization of DRWTs constrained by PDE simulations are investigated. The purpose of this study is to determine...
-
Fuel price, income and road safety as determinants of the level of the population’s economic well-being in Poland
PublicationThe opportunity to travel is one of the most favorite human activities, given that on a trip a person gets new knowledge, impressions and positive emotions. Recreational trips occupy a prominent place in the concept of the economics of happiness, and the study of factors that influence decision-making regarding travel is important for forecasting the number of tourists, infrastructure development, income and expenses of businesses...
-
Wstępne badania technologii spawania złączy narożnych ze stali niskoweglowej i nierdzewnej o grubości g=6mm i g=10mm
PublicationCelem pracy był dobór parametrów spawania dla spoin narożnych o grubości 6mm i 10mm próbek wykonanych ze stali niskowęglowej S355 i stali nierdzewnej - typu 304 (X6CrNI18-10). Złącza były spawane laserowo, jednostronnie z pełnym przetopem a powierzchnie lica i grani zapewniają uzyskanie szczelności przylegającego elementu uszczelniającego. Próbki zostały dostarczone przez Zleceniodawcę. Próby zostały przeprowadzone na stanowisku...
-
Revisiting The Determination Of Cutting Power While Sawing Of Wood With Circular Saw Blades By Means Of Fracture Mechanics
PublicationIn the classical approach, energetic effects (cutting forces and cutting power) of wood sawing process are generally calculated on the basis of the specific cutting resistance, which is in the case of wood cutting the function of more or less important factors. On the other hand, cutting forces (power) could be considered from a point of view of modern fracture mechanics. Cutting forces may be employed to determine not only toughness...
-
Wild oscillations in a nonlinear neuron model with resets: (II) Mixed-mode oscillations
PublicationThis work continues the analysis of complex dynamics in a class of bidimensional nonlinear hybrid dynamical systems with resets modeling neuronal voltage dynamics with adaptation and spike emission. We show that these models can generically display a form of mixed-mode oscillations (MMOs), which are trajectories featuring an alternation of small oscillations with spikes or bursts (multiple consecutive spikes). The mechanism by...
-
Performance evaluation of unified memory and dynamic parallelism for selected parallel CUDA applications
PublicationThe aim of this paper is to evaluate performance of new CUDA mechanisms—unified memory and dynamic parallelism for real parallel applications compared to standard CUDA API versions. In order to gain insight into performance of these mechanisms, we decided to implement three applications with control and data flow typical of SPMD, geometric SPMD and divide-and-conquer schemes, which were then used for tests and experiments. Specifically,...
-
Ruch wirowy wywoływany przez ultradźwięk w płynach z relaksacją
PublicationRozprawa doktorska poświęcona jest badaniu ruchu wirowego wywoływanego przez ultradźwięk w różnych modelach płynów z relaksacją. Ma ona charakter teoretyczny, jednak wykorzystanie uzyskanych dzięki niej wyników może przynieść lepsze zrozumienie ruchu wirowego wywoływanego przez siłę akustyczną. W I rozdziale rozprawy przedstawione zostały ogólne rozważania dotyczące akustyki nieliniowej. Rozdział II dotyczy ruchu wirowego wywoływanego...
-
Analytical method for calculation of heat source temperature drop for the Organic Rankine Cycle application
PublicationIn the paper presented are considerations on the cooperation of the limited capacity heat source with the Organic Rankine Cycle unit. Usually the heat source providing thermal energy to the Organic Rankine Cycle (ORC) may have twofold characteristics. It can be in the form of a single phase fluid, i.e. as hot exhaust gas or hot liquid, or in some cases it may be available as a phase changing fluid, as for example, technological...
-
Diffusible Hydrogen Control in Flux Cored Arc Welding Process
PublicationOne of the types of hydrogen degradation of steel welded joints is cold cracking. The direct cause of the formation of cold cracks is simultaneous presence of hydrogen, residual stresses and brittle structure. The way of preventing the occurring of degradation is to eliminate at least one of these factors. Practice has shown that the best solution is to control the amount of hydrogen in deposited metal. In this paper an experimental...
-
Waste Tyres Pyrolysis for Obtaining Limonene
PublicationThis review deals with the technologies of limonene production from waste tyre pyrolysis. Thermal decomposition is attractive for tackling the waste tyre disposal problem, as it enables both: energy to be recovered and limonene to be obtained. This material management recycling of tyres is environmentally more beneficial than the burning of all valuable products, including limonene. Given this recoverability of materials from waste...
-
Rare earth ions doped K 2 Ta 2 O 6 photocatalysts with enhanced UV–vis light activity
PublicationNew rare earth-doped K2Ta2O6 photocatalysts were successfully synthesized by hydrothermal method. The effect of dopant type (Y,Yb,Ho,Pr,Er) and amount of rare earth precursor (2,4,8 and 10 mol%) on the physicochemical and photocatalytic properties of RE-K2Ta2O6 have been investigated. All as-prepared materials were characterized by UV–vis diffuse reflectance spectroscopy, Brunauer-Emmett-Teller specific surface area measurement,...
-
Analytical methodologies for determination of artificial sweeteners in foodstuffs- a review
PublicationArtificial high-intensity sweeteners are more and more frequently used for food production. Food industry tends to highlight beneficial aspects of their use, such as tooth-friendliness, rising-up quality of life of those suffering from different forms of diabetes and possibility of weight control without sacrificing favorite unhealthy drinks or snacks. On the other hand some of the consumers are deeply concerned about safety of...
-
Hydrogen production from ethanol In nitrogen microwave plasma At atmospheric pressure
PublicationHydrogen seems to be one of the most promising alternative energy sources. It is a renewable fuel as it could be produced from e.g. waste or bio-ethanol. Furthermore hydrogen is compatible with fuel cells and is environmentally clean. In contrast to conventional methods of hydrogen production such as water electrolysis or coal gasification we propose a method based on atmospheric pressure microwave plasma. In this paper we present...
-
Towards Computer-Aided Graphene Covered TiO2-Cu/(CuxOy) Composite Design for the Purpose of Photoinduced Hydrogen Evolution
PublicationIn search a hydrogen source, we synthesized TiO2-Cu-graphene composite photocatalyst for hydrogen evolution. The catalyst is a new and unique material as it consists of copper-decorated TiO2 particles covered tightly in graphene and obtained in a fluidized bed reactor. Both, reduction of copper from Cu(CH3COO) at the surface of TiO2 particles and covering of TiO2-Cu in graphene thin layer by Chemical Vapour Deposition (CVD) were...
-
Sustainable synthesis of cyclic carbonates from bio‐based polyether polyol: the structure characterization, rheological behaviour and thermal properties
PublicationThe cycloaddition of CO2 to epoxides represents a green efficient method to form bis(cyclic carbonate)s. The main purpose of the work reported in this paper was to examine the effect of the gas flow rate (20, 40, 60 and 100 mL min–1) during carbonation on the conversion yield, chemical structure, rheological behaviour and thermal properties of the prepared compounds. A series of new bis(cyclic carbonate)s was obtained from bio‐based...
-
Thermal-Hydraulic Studies on the Shell-and-Tube Heat Exchanger with Minijets
PublicationIn this paper a patented design of a heat exchanger with minijets, with a cylindrical construction is presented. It is followed by the results of its systematic experimental investigations in the single-phase convection heat transfer mode. Based on these results, validation of selected correlations (coming from the literature) describing the Nusselt number was carried out. An assessment of the heat exchange intensification level...
-
Suitableness of SLM Manufactured Turbine Blade for Aerodynamical Tests
PublicationsettingsOrder Article Reprints Open AccessArticle Suitableness of SLM Manufactured Turbine Blade for Aerodynamical Tests by Janusz Telega 1,*ORCID,Piotr Kaczynski 1ORCID,Małgorzata A. Śmiałek 2ORCID,Piotr Pawlowski 3ORCID andRyszard Szwaba 1ORCID 1 Institute of Fluid Flow Machinery Polish Academy of Sciences (IMP PAN), Fiszera 14, 80-231 Gdansk, Poland 2 Faculty of Mechanical Engineering and Ship Technology, Institute of Naval...
-
CYP3A4 overexpression enhances apoptosis induced by anticancer agent imidazoacridinone C-1311, but does not change the metabolism of C-1311 in CHO cells
PublicationWe examine whether CYP3A4 overexpression influences the rate and pattern of antitumor imidazoacridinone C-1311 metabolism, in relation to the impact of this overexpression on cell cycle progression and final cellular response of CHO cells following C-1311 treatment. Methods: Three CHO cell lines: CHO-WT, wild type, CHO-HR, overexpressing cytochrome P450 reductase (CPR) and CHO-HR-3A4, coexpressing CPR and CYP3A4 were applied....
-
Preparation and characterization of Pt–N/TiO2 photocatalysts and their efficiency in degradation of recalcitrant chemicals
PublicationSeries of Pt–N/TiO2 photocatalysts were synthesized using the sol–gel method. The photocatalysts’ characteristics by X-ray diffractometry (XRD), scanning transmission electron microscopy (STEM), diffuse reflectance spectroscopy (DRS), X-ray photoelectron spectroscopy (XPS) showed that sample with the molar ratio Ti:N equal 1:4 and platinum nanoparticles size of about 3 nm had anatase structure, about 94 m2/g specific surface area...
-
Comparison of noise reduction methods in radiometric correlation measurements of two-phase liquid-gas flows
PublicationTwo-phase liquid-gas flows occur frequently in the mining, energy, chemical, and petrochemical industries. One of non-contact methods used to analyse these flows is the gamma ray absorption method. However, the signals received from radiation detectors contain a significant stochastic noise, which makes them difficult to analyse. The article describes four methods of noise reduction in cross-correlation measurements of water-air...
-
Joint experimental and theoretical study on low-energy elastic electron scattering by gaseous alkynes: Differential cross sections, shape resonances, and methylation effects
PublicationA detailed comparison of experimental and theoretical elastic cross sections for low-energy electron scattering by ethyne, taken earlier in our group by Gauf et al. [Phys. Rev. A 87, 012710 (2013)], and some of its methylated derivatives, propyne, and the isomers 1-butyne and 2-butyne, taken here, are presented. The present differential cross sections were measured at incident electron energies ranging from 1 eV to 30 eV and...
-
Application of the Chimney Cap as a Method of Improving the Effectiveness of Natural Ventilation in Buildings
PublicationAdequately designed natural ventilation is the cheapest and easiest way to effectively remove indoor pollutants and keep the air inside a building fresh. A prediction of the performance and effectiveness of ventilation in order to determine the design of a ventilation system can provide real and long-term cost savings. The worst time in terms of the efficiency of natural ventilation is the spring-autumn transition period [7]. In...
-
Activated Tungsten Inert Gas Weld Characteristics of P91 Joint for Advanced Ultra Supercritical Power Plant Applications
PublicationActivated Tungsten Inert Gas (A-TIG) welding, a variant of tungsten inert gas (TIG) welding, was used for welding P91. In Generation IV power plants, P91 welds are prone to premature failure due to the presence and formation of brittle phases and creep at high temperatures. When performing A-TIG welding, the flux composition plays a role in the reversal of the Marangoni flow in the weld pool, which ultimately determines the level...
-
REVERSE MODELLING OF MICROSEISMIC WAVES PROPAGATION FOR THE INTERPRETATION OF THE DATA FROM HYDRAULIC FRACTURING MONITORING IN POLAND
PublicationA hydraulic fracturing job was performed to stimulate gas flow from a horizontal wellbore located in Poland. The whole operation was overseen by means of microseismic monitoring. For this purpose, an array of 12000 geophones was deployed on ground in form of patches distributed unevenly in a region of 4km from the wellbore. The array was constantly recording seismic signals during whole fracturing processed. Such recorded signals...
-
Numerical simulation of cold flow and combustion in a swirl stabilized combustor
PublicationA numerical simulation model was developed to investigate the cold flow and combustion using Ansys FLUENT 2021R1. The governing equations were solved using the pressure-based method, and pressure–velocity coupling was performed using the SIMPLE method. To model the turbulent process, the RSM model was used. Non-premixed model is chosen to solve the chemical kinetics between fuel and oxigen. Radiation heat transfer was calculated...
-
Trends in Locally Balanced Energy Systems without the Use of Fossil Fuels: A Review
PublicationIn recent years, the idea of the operation of energy systems (power systems, heating systems) has changed significantly. This paper is an overview of locally balanced energy systems without the use of fossil fuels. The paper justifies the concept of local energy balancing in a new energy system that does not use fossil fuels (coal, natural gas, and crude oil), based on European Union guidelines and formal documents as well as the...
-
Experimental and numerical analysis of the pyrolysis dynamics of a single wood particle: presentation of the radiographic technique
PublicationPyrolysis is an oxygen-free process for the thermal decomposition of raw materials. The heat conduction and flow of pyrolysis products (i.e., the gas fraction and liquid vapour generated during pyrolysis) influence the process and products. In this work, the influence of the orientation of wooden particle fibres with respect to the direction of the heat source on the dynamics of the process was investigated, where there were two...
-
Evaluation of respiration capacity of VF in hybrid constructed wetland systems.
PublicationThree VF-beds operating in hybrid constructed wetlands in configuration HF-VF-HF were analysed. These hybrid constructed wetlands provide the II stage biological treatment. They are located in Pommerania voivodship, in Sarbsk, Wiklino and Wieszyno, and their capacities are 29.5, 14.2 and 21.6 m3/d, respectively. The article focuses on performance and operation of VF-CW plants during one year. Based on removal of organic matter...
-
Modelowanie osiągów niskoemisyjnych ogniw paliwowych za pomocą modeli matematycznych typu CFM.
PublicationW artykule przedstawiono matematyczny model rurkowego ogniwa paliwowego i jego implementację do własnego kodu typu CFM (Computational Flow Mechanics) o nazwie COM-GAS. Kody numeryczne CFM pozwalają przewidzieć podstawowe parametry ogniwa takie jak: prąd, napięcie, skład spalin etc. Napięcie generowane przez ogniwo paliwowe wyznaczono na podstawie rozszerzonego równania Nernsta. Skład spalin oszacowano opierając się o stałą równowagi...
-
Carbon nanowalls: A new versatile graphene based interface for laser desorption/ionization-mass spectrometry detection of small compounds in real samples.
PublicationCarbon nanowalls, vertically aligned graphene nanosheets, attract attention owing to their tunable band-gap, high conductivity, high mechanical robustness, high optical absorbance and other remarkable properties. In this paper, we report for the first time, the use of hydrophobic boron-doped carbon nanowalls (CNWs) for laser desorption/ionization of small compounds and their subsequent detection by mass spectrometry (LDI-MS). The...
-
Preliminary Results from the Removal of Phosphorus Compounds with Selected Sorption Material
PublicationDue to the resources of phosphorous are limited and are exhausted in the next 30 years the management of the resources is become current issue. Most of the phosphorus compounds is lost forever, because it is discharged with sewage into surface waters, causing eutrophication and in this way causing a further problem and challenge. On the other hand, there is a considerable need for phosphorus compounds, primarily in bioavailable...
-
Synteza, struktura chemiczna i właściwości bezizocyjanianowych poliuretanów otrzymywanych z wykorzystaniem CO2 oraz surowców pochodzenia naturalnego.
PublicationZ uwagi na wciąż rosnącą świadomość proekologiczną, politykę zrównoważonego rozwoju, a także nurt zielonej chemii wiodącym trendem w przemyśle tworzyw sztucznych jest poszukiwanie alternatywnych metod otrzymywania materiałów polimerowych. Komercyjnie poliuretany otrzymywane są w wyniku reakcji poliaddycji di- lub poliizocyjanianów z poliolami i małocząsteczkowymi przedłużaczami łańcucha. Z uwagi na niekorzystne właściwości diizocyjanianów,...
-
Application of Eco-innovative Technologies of Nutrients Removal in Wastewater – Case Study BARITECH Project
PublicationEco-innovative technologies in wastewater treatment should provide not only stringent standards for the quality of treated wastewater but also ensure maximum recovery of energy and raw materials from wastewater. One of the ways to improve the removal efficiency of nitrogen and phosphorus compounds in existing conventional wastewater treatment plants is pretreatment of reject water generated during the mechanical...
-
Pial artery and subarachnoid width response to apnoea in normal humans
PublicationBackground: Little is known about intracranial pressure (ICP)-cerebral haemodynamic interplay during repetitive apnoea. A recently developed method based on near-infrared transillumination/backscattering sounding (NIR-T/BSS) noninvasively measures changes in pial artery pulsation (cc-TQ) as well as subarachnoid width (sas-TQ) in humans. Method: We tested the complex response of the pial artery and subarachnoid width to apnoea...
-
Wavelet transform analysis to assess oscillations in pial artery pulsation at the human cardiac frequency
PublicationPial artery adjustments to changes in blood pressure (BP)may last only seconds in humans. Using a novelmethod called near-infrared transillumination backscattering sounding (NIR-T/BSS) that allows for the non-invasive measurement of pial artery pulsation (cc-TQ) in humans, we aimed to assess the relationship between spontaneous oscillations in BP and cc-TQ at frequencies between 0.5 Hz and 5 Hz. We hypothesized that analysis of...