Filters
total: 3604
filtered: 2802
displaying 1000 best results Help
Search results for: remelted layer
-
Resonance in Rectangular Microstrip Structure Loaded with a Pseudochiral Medium Layer
PublicationA rectangular microstrip structure with multilayer substrate containing dielectric and pseudochiral medium layers is studied in this paper. The effect of Omega medium layer location in the substrate and its thickness on the complex resonant frequency of the rectangular microstrip structure is investigated.
-
Influence of titanium layer on counter electrode on electrical parameters of DSSC
PublicationIn this paper the influence of the Ti layer thickness at counter-electrode on electrical parameters of DSSCs was examined. The transparent conductive oxide – less (TCO-less) counter electrodes (CE) with titanium layers and platinum as catalyst on Bk7 glass were prepared. Thin metallic films were deposited by means of magnetron sputtering (titanium) and Pulsed Laser Deposition (platinum). The counter electrode with Pt layer on Fluorine...
-
Performance analysis and optimization of the Radio Link Control layer in UMTS.
PublicationRLC (Radio Link Control) jest jedną z podwarstw warstwy 2 stosu radiowego systemu UMTS. RLC wspiera trzy podstawowe tryby działania: przezroczysty (Transparent Mode, TM), bezpotwierdzeniowy (Unacknowledged Mode, UM) oraz potwierdzeniowy (Acknowledged Mode, AM). Wydajność RLC AM jest mocno uzależniona od konfiguracji RLC oraz jej zdolności do dynamicznej rekonfiguracji, odzwierciedlającej zmiany w przesyłanym ruchu oraz w jakości...
-
Investigation of the Few‐Layer Black Phosphorus Degradation by the Photonic Measurements
PublicationFew-layer black phosphorus (FLBP) is a 2D material that gains worldwide interest for its possible applications, mainly in electronics and optoelec-tronics. However, as FLBP is prone to a degradation process under envi-ronmental conditions, there is a need for a monitoring method allowing investigation of its surface quality. Among many techniques, optoelectronic ones have unique advantages of fast response, non-contact, and non-invasive...
-
On efficiency of layer 2 of the radio interface protocol stack in UMTS
PublicationCelem pracy jest szczegółowa analiza funkcjonowania warstwy łącza danych w podsystemie dostępu radiowego UTRAN systemu UMTS i na tej podstawie przedstawienie szeregu zmian i usprawnień oraz wskazówek odnośnie konfiguracji protokołów, jakie należy w tej warstwie zastosować aby zmaksymalizować jej wydajność głównie pod kątem oferowanej przepływności, wprowadzanych opóźnień oraz wsparcia priorytetów przesyłanego ruchu. Teza pracy...
-
Analysis of magnetic field inside thin-layer ferromagnetic objects
PublicationResults of the numerical analysis of the magnetic field inside an infinitely long, thin-layer ferromagnetic pipe with and without a barrier were presented in this paper. Two wires with current symmetrically placed on two sides of the pipe are the sources of magnetic field. Numerical calculations for the quasi-steady state for chosen frequency band were carried out in the Flux 2D.
-
Microporous Polyurethane Thin Layer as a Promising Scaffold for Tissue Engineering
PublicationThe literature describes that the most efficient cell penetration takes place at 200–500 µm depth of the scaffold. Many different scaffold fabrication techniques were described to reach these guidelines. One such technique is solvent casting particulate leaching (SC/PL). The main advantage of this technique is its simplicity and cost efficiency, while its main disadvantage is the scaffold thickness, which is usually not less than...
-
High-speed binary-to-residue converter with the reduced input layer
Publicationprzedstawiono architekturę szybkiego konwertera z systemu binarnego do systemu resztowego dla modułów 5-bitowych. Algorytm konwersji oparty jest na dodawaniu binarnym reszt potęg liczby 2 obliczonych modulo m i redukcji modulo m sumy dla poszczególnych modułów bazy systemu resztowego. Warstwa wejciowa konwertera jest redukowana poprzez wykorzystanie wspólnych elementów układu dla odpowiednio zestawionych par modułów.
-
Small-signal admittance for Schottky-Richardson emission into an organic layer
PublicationPraca przedstawia małosygnalową admitancję emisji Schottky'ego-Richardsona do warstwy organicznej. Analiza obejmuje obie składowe zespolonej odpowiedzi.
-
Surface quality control of a thin SiN layer by optical measurements
PublicationFiber optic interferometers have a wide range of applications, including biological and chemical measurements. Nevertheless, in the case of a reflective interferometer setup, standard silver mirrors cannot be used in every measurement, due to their chemical activity. This work investigates the surface quality of a thin optical layer of silicon nitride (SiN), which can serve as an alternative material for silver mirrors. We present...
-
Spectroscopic Optical Coherence Tomography for Thin Layer and Foil Measurements
PublicationThe main goal of this research was to assess if it is possible to evaluate the thickness of thin layers (both thin films on the surface and thin layers below the surface of the tested object) and foils using optical coherence tomography (OCT) for thickness assessment under the resolution of the standard commercially available OCT measurement system. In the proposed solution, light backscattered from the evaluated thin layer has...
-
Excitonic stimulation of current flowing along thin tetracene layer
PublicationW pracy badane były prądy będące wynikiem oddziaływania ekscytonów tripletowych ze spułapkowanymi nośnikami ładunku w warstwach tetracenu. Badane próbki oświetlane były od strony podłoża oraz od strony przeciwległej podłożu.
-
Deterministic and statistical size effect during shearing of granular layer
PublicationArtykuł omawia deterministyczny i statystyczny efekt skali w materiałach granulowanych podczas ścinania cienkiej warstwy piasku między dwoma bardzo szorstkimi ścianami. Obliczenia wykonano metodą elementów skończonych na bazie mikropolarnego prawa hipoplastycznego. Pokazano wyniki efektu skali przy zastosowaniu różnych metod redukujących ilość realizacji pól losowych dla początkowego wskaźnika porowatości..
-
Wpływ nadtapiania laserowego w warunkach kriogenicznych na strukturę warstwy wierzchniej stopu Ti-6Al-4V = Effect of laser melting at cryogenic conditions on structure of the surface layer of the Ti-6Al-4V alloy
PublicationWykonano nadtapianie laserowe stopu Ti-6Al-4V zanurzonego w środowisku ciekłego azotu. Badania mikroskopowe wykazały znaczący wpływ parametrów nadtapiania na grubość, mikrostrukturę i mikrotwardośc warstwy wierzchniej.
-
<title>Software layer for SIMCON ver. 2.1. FPGA based LLRF control system for TESLA FEL part II: application layer, networking, examples</title>
Publication -
Napawane laserowo warstwy na bazie kobaltu - zmienność morfologii i własności. Część 1. Cobalt base, laser cladding layers - morfology and properties variation. Part 1
PublicationPrzedmiotem badań były szczegóły budowy warstwy napawanej laserowo z zastosowaniem trzech ściegów oraz analiza wpływu zróżnicowanej budowy warstwy na jej mikrotwardość.
-
Napawane laserowo warstwy na bazie kobaltu - zmienność morfologii i własności. Część 2. Cobalt base, laser cladding layers - morfology and properties variation. Part 2
PublicationPrzedmiotem badań były szczegóły budowy warstwy napawanej laserowo z zastosowaniem trzech ściegów oraz analiza wpływu zróżnicowanej budowy warstwy na jej mikrotwardość.
-
Evaluation of the mechanical strength and protective properties of polycarbonate toecaps subjected to repeated impacts simulating workplace conditions
Publication -
Neonatal excitotoxic ventral hippocampal damage alters dopamine response to mild repeated stress and to chronic haloperidol
Publication -
Repeated Intra-Articular Administration of Platelet-Rich Plasma (PRP) in Temporomandibular Disorders: A Clinical Case Series
Publication -
PCR amplification with primers based on IS2404 and GC-rich repeated sequence reveals polymorphism in Mycobacterium ulcerans
PublicationOpracowano prostą w wykonaniu metodę genotypowania szczepów bakterii z gatunku Mycobacterium ulcerans. Polimorfizm genetyczny 32 badanych izolatów Mycobacterium ulcerans odzwierciedla ich geograficzne pochodzenie z rejonów Afryki Centralnej, Ameryki Południowej i Łacińskiej, Azji Południowo-Wschodniej, Malezji oraz Australii.
-
Discrimination of hospital isolates of Acinetobacter baumannii using repeated sequences and whole genome alignment differential analysis
PublicationAn optimized method for bacterial strain differentiation, based on combination of Repeated Sequences and Whole Genome Alignment Differential Analysis (RS&WGADA), is presented in this report. In this analysis, 51 Acinetobacter baumannii multidrug-resistance strains from one hospital environment and patients from 14 hospital wards were classified on the basis of polymorphisms of repeated sequences located in CRISPR region, variation...
-
Development of laser technology in Poland
Publication -
Laser Technology and Applications 2012
Publication -
Measurements of Subnanometer Molecular Layers
PublicationSelected methods of formation and detection of nanometer and subnanometer molecular layers were shown. Additionally, a new method of detection and measurement with subnanometer resolution of layers adsorbed or bonded to the gate dielectric of the ion selective field effect transistor (ISFET) was presented.
-
InGaN trapered laser diodes
PublicationW pracy zaprezentowano rezultaty badan nad diodami laserowymi InGaN ze zwężającym się kanałem. Kąty kanałów zmieniane były w zakresie 2 -5 stopni, jak również zmieniana była długość kanału. Wykazano, że w przypadku optymalnych parametrów, parametr M2 (M kwadrat) opisujący odtępstwa wiązki od krzywej Gaussa, wynosił 2.1 przy mocy optycznej 200 mW.
-
The surface photoconductivity in molecular layers
PublicationW pracy przedstawiono rezultaty analizy fotoprądów powierzchniowych w cienkich warstwach tetracenu i pentacenu. W szczególności badano wpływ obecności defektów strukturalnych w warstwach na charakterystyki fotoprądów i transport nośników ładunku.
-
Effect of Laser Treatment on Intrinsic Mechanical Stresses in Titanium and Some of Its Alloys
PublicationLaser surface treatment conducted at different power levels is an option to modify titanium bone implants to produce nano- and microtopography. However, such processing can lead to excess mechanical stress within the surface layer. This research aims to calculate the level of such residual stresses after the surface processing of Ti grade IV, Ti15Mo, and Ti6Al7Nb alloys with an Nd:YAG laser. Light and scanning electron microscopies...
-
Second law analysis of a 3D magnetic buoyancy-driven flow of hybrid nanofluid inside a wavy cubical cavity partially filled with porous layer and non-Newtonian layer
Publication -
Managing data from heterogeneous data sources using knowledge layer
PublicationW procesie integrowania danych przy użyciu ontologii, ważne jest aby zarządzać danymi przechowywanymi w zewnętrznych źródłach, analogicznie jak tymi przechowywanymi w Bazie Wiedzy. Zaprezentowana w poprzednich pracach metoda kartograficznej reprezentacji wiedzy pozwala na wnioskowanie z danych przechowywanych w Bazie wiedzy. Rozwiązanie zaprezentowane w tej pracy umożliwia wykorzystanie metody kartograficznej do wnioskowania z...
-
Shape Restoration of Deformed Egg-Shaped Single Layer Space Frames
Publication -
The influence of implantation on mechanical degradation of the nanotubular oxide layer on titanium screws
Publication -
Degradation of Gel-Coat Layer in Glass/Polyester Laminate in Seawater Environment
Publication -
The Influence of ZnO Oxide Layer on the Physicochemical Behavior of Ti6Al4V Titanium Alloy
Publication -
Wettability of plasma modified glass surface with bioglass layer in polysaccharide solution
Publication -
Selection of measurement frequency in Mott–Schottky analysis of passive layer on nickel
Publication -
Investigations of the passive layer cracking by means of Dynamic Electrochemical Impedance Spectroscopy
Publication -
Degradation of Gel-Coat Layer in Glass/Polyester Laminate in Seawater Environment
PublicationGlass/polyester laminate coated with gelcoat layer of different thickness 0,5; 1,5; 3 mm was studied in terms of blistering behaviour and water sorption in hot water environment. Blistering was found to be accelerated for thin (0,5 mm) gel-coat layer compared to the thick (1,5; 3 mm), however no significant difference in blistering behaviour was observed between the laminates with gel-coat thickness 1,5 and 3 mm which may suggest...
-
Thin Layer Deposition Methods in Solid Oxide Fuel Cell Technology
Publication -
The Effect Fabrication Method of Cobalt Base Clad Layer On Air Oxidation
PublicationNapawane warstwy ze stopu kobaltu zostały wykonane za pomocą napawania plazmowego (PTA) oraz laserowego. Zostały one poddane utlenia niu w temperarurze 1100 stopni celsiusza prze 200 godzin. Przeprowadzono badania mikrostruktury i składu chemicznego warstwy tlenkowej oraz głębszych warstw napoiny. Nie stwierdzono wpływu metody wytwarzania na skutki procesu utleniania.
-
Stability of Diodes with Poly(3-hexylthiophene) and Polyazomethines Thin Organic Layer
Publication -
Application of a hash function to discourage MAC-layer misbehaviour in wireless LANs.
PublicationProtokoły przypadkowego wielodostępu w warstwie MAC bezprzewodowych sieci lokalnych wykorzystują algorytm odkładania transmisji o losowo wybrany odcinek czasu. Odstępstwo od losowego wyboru czasu odłożenia może zapewnić stacji niesprawiedliwie duży udział w paśmie sieci. W pracy przedstawiono protokół dostępu przeciwdziałający tego rodzaju zachowaniom, oparty na zastosowaniu funkcji mieszającej. Jako argument funkcji przyjmuje...
-
Photoenhanced current as a tool for investigating non-uniform structures of tetracene layer.
PublicationPowierzchniowe prądy fotowzmocnione używane były jako narzędzie do badań fizycznych własności powierzchni warstw od strony podłoża, a także od strony przeciwległej podłożu.
-
Investigations of the passive layer cracking by means of dynamic electrochemical impedance spectroscopy.
PublicationDynamiczna elektrochemiczna spektroskopia impedancyjna została wykorzystana do badania pękania warstwy pasywnej na austenitycznej stali wysokostopowej.Zbadano efekt narzuconego potencjału oraz naprężeń rozciągających na pękanie korozyjne stali wysokostopowej 304L w środowisku 0.5M NaCl w temperaturze pokojowej. Praca przedstawia chwilowe widma impedancyjne uzyskane dla badanego układu przy różnych wartościach potencjałów. Uzyskane...
-
A theoretical consideration of a free convective boundary layer on an isothermal horizontal conic.
PublicationPrzedstawiono rozwiązanie analityczne naturalnej konwekcji swobodnej od izotermicznego, poziomego stożka o kącie przy podstawie alfa. Rozwiązanie przeprowadzono w oparciu o typowe dla konwekcji swobodnej założenia upraszczające. Rozwiązania dla przypadków granicznych (poziomy walec i pionowa płyta kołowa) wykazują dobrą zgodność z danymi literaturowymi.
-
Investigations of non-uniform structure of the tetacene layer by photoen-hanced current
PublicationBadano stany pułapkujące nośniki w powierzchniowych obszarach warstwy tetra-cenu. W badaniach wykorzystano metodę prądów fotowzmocnionych. Wykazano obe-cność różnych rozkładów energetycznych pułapek przy obu powierzchniach war-stw tetracenu.
-
The structure and melting of lead nanocrystalline layer in reduced lead-germanate glass
PublicationNanokrystaliczna warstwa granul Pb na powierzchni szkieł ołowiowo-germanianowych została wytworzona poprzez wygrzewanie w wysokich temperaturach, w atmosferze wodoru. Właściwości tej warstwy silnie zależą od temperatury i czasu redukcji. Artykuł prezentuje rentgenowskie i mikroskopowe badania struktury warstwy oraz wpływ topnienia i krzepnięcia granul Pb na jej przewodnictwo.
-
Managing Data from Heterogeneous Data Sources Using Knowledge Layer
Publication -
SDN testbed for validation of cross-layer data-centric security policies
PublicationSoftware-defined networks offer a promising framework for the implementation of cross-layer data-centric security policies in military systems. An important aspect of the design process for such advanced security solutions is the thorough experimental assessment and validation of proposed technical concepts prior to their deployment in operational military systems. In this paper, we describe an OpenFlow-based testbed, which was...
-
Biophotonic low-coherence sensors with boron-doped diamond thin layer
PublicationLow-coherence sensors using Fabry-Perot interferometers are finding new applications in biophotonic sensing, especially due to the rapid technological advances in the development of new materials. In this paper we discuss the possibility of using boron-doped nanodiamond layers to protect mirror in a Fabry-Perot interferometer. A low-coherence sensor using Fabry-Perot interferometer with a boron-doped nanodiamond (B-NCD) thin protective...