Filters
total: 4167
filtered: 2275
-
Catalog
- Publications 2275 available results
- Journals 20 available results
- Conferences 2 available results
- Publishing Houses 2 available results
- People 87 available results
- Inventions 9 available results
- Projects 8 available results
- Research Teams 1 available results
- Research Equipment 3 available results
- e-Learning Courses 166 available results
- Events 5 available results
- Open Research Data 1589 available results
Chosen catalog filters
displaying 1000 best results Help
Search results for: WHITTAKER FILTER
-
A Trisection Filter Design With Negative Slope of Frequency-Dependent Crosscoupling Implemented in Substrate Integrated Waveguide (SIW)
PublicationThis letter reports on a novel realization of a microwave bandpass filter in a triplet configuration with a frequency-dependent crosscoupling implemented in substrate integrated waveguide (SIW). The design involves implementing dispersive coupling with a negative slope, a feature that allows the capabilities of the classic triplet topology to be extended. In this particular case, the implementation of two transmission zeros on...
-
Stability of softly switched multiregional dynamic output controllers with a static antiwindup filter: A discrete-time case
PublicationThis paper addresses the problem of model-based global stability analysis of discrete-time Takagi–Sugeno multiregional dynamic output controllers with static antiwindup filters. The presented analyses are reduced to the problem of a feasibility study of the Linear Matrix Inequalities (LMIs), derived based on Lyapunov stability theory. Two sets of LMIs are considered candidate derived from the classical common quadratic Lyapunov...
-
Coupled-Resonator Waveguide Filter in Quadruplet Topology With Frequency-Dependent Coupling - A Design Based on Coupling Matrix
PublicationThis letter presents an application of a recently developed coupling matrix synthesis technique to design of coupled-resonator filters with dispersive inter-resonator couplings. This technique is used to design a novel coupled-cavity bandpass filter. Measurements validate the design and confirm effectiveness of the synthesis method. The filter is a four-pole generalized Chebyshev filter with three transmission zeros. Resonators...
-
Fifth-order low-pass CMOS OTA-C continuous-time filter with on-chip automatic tuning
PublicationW pracy przedstawiono budowę operacyjnego wzmacniacza transkonduktancyjnego (OTA) zasilanego napięciem stałym 2.8-4.5V wykonanego w technologii CMOS0.8um n-well. Wzmacniacz ten wykorzystano do budowy dolnoprzepustowego filtru czasu ciągłego typu OTA-C piątego rzędu. W układzie scalonym umieszczono także blok automatycznego dostrajania częstotliwości odcięcia filtru. Przedstawiono wyniki symulacji komputerowych (modele MOS BSIM3v3)...
-
Highly-Compact Dual-Band Bandpass Waveguide Filter Based on Cross-Shaped Frequency-Dependent Coupling
PublicationThis work reports the design of an original class of highly-compact dual-band bandpass filter based on dual-mode waveguide resonators inter-coupled through a novel type of frequency-dependent coupling (FDC). The devised FDC consists of a cross-shaped metallic structure placed in the broad wall of a rectangular waveguide. This FDC produces two additional poles and three extra transmission zeros (TZs). Specifically, each pole is...
-
Compact, Order Extensible and Wide-Stopband Bandpass Filter Based on SIW Cavity with Rectangular Ring Slot
PublicationThis article introduces novel architectures of bandpass filters (BPFs) using a substrate integrated waveguide (SIW) cavity with a rectangular ring slot (RRS) for compact size, extensible order, and broad stopband responses. Two bandpass filters, which demonstrate a second-and a fourth-order Chebyshev response, respectively, are realized by employing identical cavities with RRS, without increasing the physical size of the circuit....
-
Filter-Hilbert Method for Automatic Correction of Non-Anechoic Antenna Measurements with Embedded Self-Calibration Mechanism
PublicationOne of the most important steps in the process of antenna development involves measurements of its prototype. Far-field performance of radiators is normally characterized in strictly controlled environments such as anechoic chambers which can ensure certification-grade accuracy. Unfortunately, they are also characterized by high construction costs which might not be justified for low-budget research and/or teaching-related activities....
-
Microstrip line with short-circuited edge as a high-pass filter operating up to millimeter-wave frequencies
PublicationPrzedstawiono prosty planarny filtr górnoprzepustowy wykorzystujący linię mikropaskową ze zwartym brzegiem. Układy zaprojektowano w taki sposób, aby pasmo przepustowe rozpoczynało się w zakresie K lub Ka. Wykonano dwa prototypy: na podłożu w postaci warstwy dielektrycznej wykonanej z ceramiki alundowej oraz na podłożu organicznym o niskiej przenikalności elektrycznej. Wykazano dużą zgodność teoretycznych i pomierzonych charakterystyk...
-
A 0.5 V Nanowatt Biquadratic Low-Pass Filter with Tunable Quality Factor for Electronic Cochlea Applications
PublicationA novel implementation of an analogue low-power, second-order, low-pass filter with tunable quality factor (Q) is presented and discussed. The filter feature is a relatively simple, buffer-based, circuit network consisting of eleven transistors operating in a subthreshold region. Q tuning is accomplished by injecting direct current into a network node, which changes the output resistance of the transistors and, as a result, modifies...
-
Speed sensorless ac drive with inverter output filter and fault detection using load torque signal
PublicationIn this paper, a sensorless induction motor (IM) drive using speed observer system is presented. The system includes load torque computation for gear fault detection. Nonlinear control method is adopted for controlling the motor over a wide speed range. An LC filter for smoothing current and voltage waveforms is used at the output of the voltage inverter. The use of filter imposes more building of the used observer to avoid using...
-
Lattice filter based multivariate autoregressive spectral estimation with joint model order and estimation bandwidth adaptation
PublicationThe problem of parametric, autoregressive model based estimation of a time-varying spectral density function of a multivariate nonstationary process is considered. It is shown that estimation results can be considerably improved if identification of the autoregressive model is carried out using the two-sided doubly exponentially weighted lattice algorithm which combines results yielded by two one-sided lattice algorithms running...
-
Estimation of time-frequency complex phase-based speech attributes using narrow band filter banks
PublicationIn this paper, we present nonlinear estimators of nonstationary and multicomponent signal attributes (parameters, properties) which are instantaneous frequency, spectral (or group) delay, and chirp-rate (also known as instantaneous frequency slope). We estimate all of these distributions in the time-frequency domain using both finite and infinite impulse response (FIR and IIR) narrow band filers for speech analysis. Then, we present...
-
MATCHED FILTER APPROACH FOR MICROSEISMIC SIGNAL PROCESSING OF REAL DATA FROM EAST POMERANIA SHALE GAS
PublicationThe microseismic monitoring is a method of monitoring of fracture propagation during hydraulic fracturing (HF)process. An array of several hundred geophones is placed on the surface to record little ground tremors induced by fracturing process. Filtration and summation of signals from geophones is essential to identify and locate fracturing events from underground. Authors propose a method of matched filtering, that is usually...
-
Speed Sensorless AC Drive with Inverter LC Filter and Fault Detection Using Load Torque Signal
PublicationThe industrial development in recent years has seen a major increase in the use of induction motors, whereby the cost has to be as low as possible and the lifetime as long as possible. To follow up this desire, investigations in this area have become very intense. For that reason, this paper presents a solution for driving an induction motor and simultaneous fault detection with no need for additional sensors. In order to achieve...
-
Variable-structure algorithm for identification of quasi-periodically varying systems
PublicationThe paper presents a variable-structure version of a generalized notchfiltering (GANF) algorithm. Generalized notch filters are used for identification of quasi-periodically varying dynamic systems and can be considered an extension, to the system case, of classical adaptive notch filters. The proposed algorithm is a cascade of two GANF filters: a multiple-frequency "precise" filter bank, used for precise system tracking, and a...
-
Silver intercalated carbon nanotubes
Publication -
Thermoplastic Elastomers Filled With GTR
PublicationIn recent years, searching for new and cost-effective methods of recycling waste tires has been a subject of research in many laboratories worldwide. This is due to regulations in the law and environmental factors, which have both stimulated industry to re-use high quality rubber found in ground tire rubber (GTR). One of the most promising solutions in this area seems to be thermoplastic elastomers (TPEs) filled with GTR, which...
-
Processing and structure–property relationships of natural rubber/wheat bran biocomposites
PublicationIn this work, wheat bran was used as cellulosic filler in biocomposites based on natural rubber. The impact of wheat bran content [ranging from 10 to 50 parts per hundred rubber (phr)] on processing, structure, dynamic mechanical properties, thermal properties, physico-mechanical properties and morphology of resulting biocomposites was investigated. For better characterization of interfacial interactions between natural rubber...
-
Novel microstrip low-pass filters with fractal defected ground structures
PublicationIn this study, three microstrip low-pass filters (LPFs) containing fractal-shaped defected ground structures have been designed and manufactured. To improve the performance of microstrip LPF, cascades of inductively coupled fractal resonators have been applied. Simultaneously, to achieve relatively constant microstrip impedance resulting in essentially low reflection losses, a modification of the strip geometry has been introduced....
-
Design of Analog Filters with Single Transmission Zeros, Dedicated for HFB Systems
Publication -
Fast multiplexer cad using surrogate models for channel filters synthesis
Publicationartykuł przedstawia metodę szybkiego projektowania multiplekserów mikrofalowych wykorzystującą dokładne modele zastępcze na etapie projektowania kanałów. przedstawiony został przykład trój-kanałowego multipleksera z filtrami dwurodzajowymi.
-
Multisensor Tracking of Marine Targets - Decentralized Fusion of Kalman and Neural Filters
Publication -
Pollutants removal effectiveness in hydrophyte filters with sequential vertical and horizontal flow
PublicationThe object of investigations was the constructed wetland in Wiedersberg in Saxonia in Germany supplied with domestic sewage from 145 inhabitants. The biological part was composed of sequential reed beds with vertical and horizontal flow of sewage. It in one of new solutions, because up till now configuration with vertical bed situated at front of biological part of treatment was applied.The evaluation of object performance was...
-
Generalized Chebyshev Bandpass Filters With Frequency-Dependent Couplings Based on Stubs
PublicationThis paper presents an accurate synthesis method for inline and cross-coupled generalized Chebyshev bandpass filters with frequency-dependent couplings implemented via open and short stubs. The technique involves the synthesis of a lumped-element prototy pe in the form of a coupling matrix with a frequency-dependent term and the conversion of this prototype to a distributed-element mode l composed of sections of TEM lines. This...
-
Technique to improve CMRR at high frequencies in CMOS OTA-C filters
PublicationIn this paper a technique to improve the common-mode rejection ratio (CMRR) at high frequencies in the OTA-C filters is proposed. The technique is applicable to most OTA-C filters using CMOS operational transconductance amplifiers (OTA) based on differential pairs. The presented analysis shows that a significant broadening of CMRR bandwidth can be achieved by using a differential pair with the bodies of transistors connected to...
-
Accurate design of pseudoelliptic inline SIW filters with frequency-dependent couplings
PublicationThis paper presents an accurate synthesis method for inline SIW (Substrate Integrated Waveguide) generalized Chebyshev bandpass filters with frequency-dependent couplings. The technique is based on the synthesis of a coupling matrix that takes into account the impedance of the frequency-dependent stub. Thus, a loading effect compensation in adjacent resonators (via resonant frequency adjustment) and coupling elements (via coupling-value...
-
Nonlinear viscoelasticity in Three Dimensional filler reinforced rubber composites and nanocomposites
PublicationThis chapter describes the influence of three-dimensional nanofillers used in elastomers on the nonlinear viscoelastic properties. In particular, this part focuses and investigates the most important three-dimensional nanoparticles, which are used to produce rubber nanocomposites. The rheological and the dynamic mechanical properties of elastomeric polymers, reinforced with spherical nanoparticles, like POSS, titanium dioxide and...
-
Coupled-resonator filters with frequency-dependent couplings: coupling matrix synthesis
Publication -
On the synthesis of coupled-lossy resonator filters with unloaded quality factor control
PublicationA technique for fast synthesis of coupling matrix low-pass prototypes of generalized Chebyshev bandpass filters with lossy resonators is presented in this paper. The coupling matrix is found by solving a nonlinear least squares problem based on zeros and poles of filter's transfer functions. Additional constraints are introduced that allow one to control the level of unloaded quality factor of resonators.
-
Continuous-time active-RC filters: general model and its applications.
PublicationW pracy przedstawiono ogólny model filtru aktywnego RC opartego na wzmacniaczach odwracających fazę. Model analizowany jest przy użyciu równań macierzowych. Podano jawną formułę określającą funkcję przenoszenia filtru w ogólnym przypadku. Przedstawiono rozszerzenia modelu pozwalające uwzględniać nieidealności wzmacniaczy operacyjnych, w tym skończone wzmocnienie i pasmo przenoszenia oraz niezerową rezystancję wyjściową. Zastosowanie...
-
Sensitivity performance of all pole canonical low pass GmC filters.
PublicationW pracy badano własności częstotliwościowe kanonicznych filtrów dolnoprzepustowych GmC bez zer transmisyjnych. Przedstawiono ogólną strukturę kanonicznego filtru dolnoprzepustowego i jej opis macierzowy. Wyprowadzono ogólne wzory określające funkcje wrażliwościowe filtru. Dokonano porównania struktur do 10-go rzędu włącznie dla aproksymacji Butterwortha, Czebyshewa i Bessela.
-
Design of highly linear tunable CMOS OTA for continuous-time filters
PublicationW pracy przedstawiono analityczną metodę projektowania wzmacniaczy transkon-duktancyjnych CMOS o bardzo dobrej liniowości. Zaproponowano dwie wersje układu różniące się umiejscowieniem dodatkowej pary różnicowej służącej do kompensacji nieliniowości charakterystyki przejściowej. Praca zawiera wyniki symulacji pełnych wersji obu układów otrzymane przy użyciu symulatora SPICE.
-
General Description of State-Space Continuous-Time Gm-C Filters
PublicationW pracy przedstawiono ogólne podejście do analogowych filtrów Gm-C czasuciągłego, oparte o opis macierzowy. Przedstawiono związki pomiędzy sieciąpasywną filtru a funkcją przenoszenia. Podano nową definicję filtrów zmien-nych stanu Gm-C oraz opisano dwie interesujące podklasy filtrów Gm-C jakrównież podano kanoniczne transformacje przekształcające struktury z pojem-nościami nieuziemionymi w struktury zawierające wyłącznie...
-
Low order autoregressive (AR) models for FDTD analysis of microwave filters.
PublicationArtykuł opisuje zastosowanie modeli AR w celu poprawy efektywności analizy struktur filtrujących metodą różnic skończonych w dziedzinie czasu (FD-TD). Opisanych jest szereg kryteriów pozwalających na automatyczne tworzenie modeli AR sygnałów czasowych, w tym wybór fragmentu odpowiedzi układu stanowiący podstawę ekstrakcji współczynników modelu, współczynnika decymacji oraz rzędu modelu. Skuteczność wprowadzonych kryteriów...
-
Rectangular Waveguide Filters Based on Deformed Dual-Mode Cavity Resonators
PublicationIn this paper, a novel design for rectangular waveguide filters with deformed dual-mode (DM) cavity resonators is demonstrated. The new resonant cavity shape is a result of applying shape deformation to the basic rectangular cavity to enable its dual-mode operation. Internal coupling between the two orthogonal cavity modes is realized by geometry deformation, eliminating the need for additional coupling elements. The designs are...
-
A simple way of increasing estimation accuracy of generalized adaptive notch filters
PublicationGeneralized adaptive notch filters are used for identification/tracking of quasi-periodically varying dynamic systems and can be considered an extension, to the system case, of classical adaptive notch filters. It is shown that frequency biases, which arisein generalized adaptive notch filtering algorithms, can be significantly reduced by incorporating in the adaptive loop an appropriately chosen decision delay. The resulting performance...
-
Fast Design Optimization of Waveguide Filters Applying Shape Deformation Techniques
PublicationThis paper presents an efficient design of microwave filters by means of geometry optimization using shape deformation techniques. This design procedure allows for modelling complex 3D geometries which can be fabricated by additive manufacturing (AM). Shape deforming operations are based on radial basis function (RBF) interpolation and are integrated into an electromagnetic field simulator based on the 3D finiteelement method (FEM)....
-
The Design of Cavity Resonators and Microwave Filters Applying Shape Deformation Techniques
PublicationThis article introduces shape deformation as a new approach to the computer-aided design (CAD) of high-frequency components. We show that geometry deformation opens up new design possibilities and offers additional degrees of freedom in the 3-D modeling of microwave structures. Such design flexibility is highly desirable if the full potential of additive manufacturing (AM) is to be exploited in the fabrication of RF and microwave...
-
A Novel Synthesis Technique for Microwave Bandpass Filters with Frequency-Dependent Couplings
PublicationThis paper presents a novel synthesis technique for microwave bandpass filters with frequency-dependent couplings. The proposed method is based on the systematic extraction of a dispersive coupling coefficient using an optimization technique based on the zeros and poles of scattering parameters representing two coupled resonators.The application of this method of synthesis is illustrated using two examples involving four and five-pole...
-
Testing Stability of Digital Filters Using Optimization Methods with Phase Analysis
PublicationIn this paper, novel methods for the evaluation of digital-filter stability are investigated. The methods are based on phase analysis of a complex function in the characteristic equation of a digital filter. It allows for evaluating stability when a characteristic equation is not based on a polynomial. The operation of these methods relies on sampling the unit circle on the complex plane and extracting the phase quadrant of a function...
-
Comprehensive compensation of grid current distortion by shunt active power filters
PublicationThe paper presents a comprehensive approach to the compensation of grid current distortion in shunt active power filter systems. Four sources of current distortion are addressed: imperfect grid synchronization caused by the distortion in the grid voltages, time delays in the evaluation of grid voltages and computation of compensating currents, fluctuations of the dc bus voltage, and the distortion of inverter output voltages due...
-
Copper Slag as a Potential Waste Filler for Polyethylene-Based Composites Manufacturing
PublicationThe present study aimed to analyze the application of waste material from copper production– copper slag (ŻŻL) as filler for composites based on the high-density polyethylene (HDPE). Copper slag filler was introduced in the amounts of 1–20 wt%, and its influence on the appearance (color analysis), chemical structure (Fourier-transform infrared (FTIR) spectroscopy), microstructure (optical microscopy), as well as static (tensile...
-
Application of regularized Savitzky–Golay filters to identification of time-varying systems
PublicationSavitzky–Golay (SG) filtering is a classical signal smoothing technique based on the local least squares approximation of the analyzed signal by a linear combination of known functions of time (originally — powers of time, which corresponds to polynomial approximation). It is shown that the regularized version of the SG algorithm can be successfully applied to identification of time-varying finite impulse response (FIR) systems....
-
Fast Full-Wave Multilevel Zero-Pole Optimization of Microwave Filters
PublicationA new concept is proposed for the full-wave computer-aided design of microwave filters. The method consists of two stages and operates on the zeros and poles of the transfer function and their derivatives. These quantities are evaluated from the response computed by a full-wave electromagnetic solver with two levels of accuracy. The two stages make use of different models that are optimized using a low-accuracy electromagnetic...
-
A multi-pulse diode rectifier with a coupled three-phase reactor and additional small shunt active power filter
Publication -
Supply system based on the 18-pulse diode rectifier with coupled reactors and integrated with the series active power filter
Publication -
Design of Highly Selective Dual Band Band Stop Filter using Dual-Path Step Impedance Resonator
Publication -
Particle Filter Modification using Kalman Optimal Filtering Method as Applied to Road Detection from Satellite Images
PublicationIn the paper recursive state estimation approach is presented as applied to satellite images. Especially, a model of dynamic systems of the non-linear and non-Gaussian systems is presented, and finally the Kalman filter and particle filter and an integration of both is figured out. Special attention is paid to the application for satellite image analysis.
-
Miniaturized bandpass substrate integrated waveguide filter with frequency-dependent coupling realized using asymmetric GCPW discontinuity
PublicationAn asymmetric GCPW discontinuity is proposed to provide frequency-dependent coupling in microwave bandpass filters. Wider and narrow sections introduce, respectively, the capacitive and inductive component to the equivalent circuit representing coupling. By selecting the dimensions of the discontinuity and width of the inductive window in substrate integrated waveguide, an additional transmission zero can be introduced at prescribed...
-
A nine-input 1.25 mW, 34 ns CMOS analog median filter for image processing in real time
PublicationIn this paper an analog voltage-mode median filter, which operates on a 3 × 3 kernel is presented. The filter is implemented in a 0.35 μm CMOS technology. The proposed solution is based on voltage comparators and a bubble sort configuration. As a result, a fast (34 ns) time response with low power consumption (1.25 mW for 3.3 V) is achieved. The key advantage of the configuration is relatively high accuracy of signal processing,...