Search
Filters
total: 2957
filtered: 923
-
Catalog
Chosen catalog filters
Search results for: TAPERED PILE:
-
Multimode tapered optical light pipe for illumination systems
Publication -
Bearing capacity of monotonically installed tapered piles in medium dense Fontainebleau sand
PublicationA series of installation of tapered piles in medium-dense Fontainebleau sand were performed in the geotechnical centrifuge at Gustave Eiffel University. The models of piles with three different shapes - straight profile (S), and with taper angle of 0.70 degrees (T1), and 1.4 degrees (T2) were used. The piles were instrumented with fiber optic wires on the shaft and load cell at the base. After monotonic installation, the models were...
-
The improvement of axial bearing capacity of open-end pipe piles
PublicationZaproponowano sposób zwiększania nośności osiowej pali rurowych z otwartym dnem za pomocą wewnętrznych pierścieni. Przedstawiono wyniki badań w skali naturalnej i badań modelowych. Przeprowadzono analizę teoretyczną zjawiska metodą analityczną i numeryczną. Badania i analizy potwierdziły skuteczność proponowanego rozwiązania technicznego.
-
Estimation of pile bearing capacity by dynamic and static tests
PublicationBadania dynamiczne, szczególnie dla pali wbijanych, w budownictwie hydrotechnicznym stają się coraz bardziej popularne. Badania, poparte formalnie zapisami zawartymi w Eurokodzie 7, wykorzystywane w badaniach ''na wodzie'' i ''na lądzie'' są szybkie i ekonomiczne. Przedstawiono serię badań dla gruntów uwarstwionych dla pali prefabrykowanych żelbetowych, wbijanych stalowych pali rurowych oraz pali Vibro-Fundex. Badania dynamiczne...
-
Pile Model Tests Using Strain Gauge Technology
PublicationOrdinary pile bearing capacity tests are usually carried out to determine the relationship between load and displacement of pile head. The measurement system required in such tests consists of force transducer and three or four displacement gauges. The whole system is installed at the pile head above the ground level. This approach, however, does not give us complete information about the pile-soil interaction. We can only determine...
-
Numerical analysis of pile installation effects in cohesive soils
PublicationIn this thesis the empirical equation for radial effective stress calculation after displacement pile installation and following consolidation phase has been proposed. The equation is based on the numerical studies performed with Updated Lagrangian, Arbitrary Lagrangian-Eulerian and Coupled Eulerian-Lagrangian formulations as well as the calibration procedure with database containing world-wide 30 pile static loading tests in cohesive...
-
The mechanism of grouting action under the base of bored pile
PublicationThe grouting under the base of bored pile is carried out in order to reduce pile settlement and improve its bearing capacity. The principal aim of grouting is to introduce an initial force between the soil and the pile base. In non-cohesive soil, the grouting can also enlarge the pile base area and therefore improve the base resistance. The example of static load tests on instrumented bored piles installed with and without grouting...
-
FEM modelling of screw displacement pile interaction with subsoil
PublicationPredicting the-settlement characteristics of piles is an important element in the designing of pile foundations. The most reliable method in evaluating pile-soil interaction is the static load test, preferably performed with instrumentation for measuring shaft and pile base resistances. This, however, is a mostly post-implementation test. In the design phase, prediction methods are needed, in which numerical simulations play an...
-
New concept of drilling auger for displacement pile installation
PublicationIn 2020, a new version of the screw displacement auger for pile installation in soil was developed and patented in Poland. It was named DPDT (Displacement Pile Drilling Tool). The general aim of its development was to reduce the soil resistances to the auger during screwing into the ground while maintaning a good load-bearing capacity for the screw displacement piles. The “DPDT-Auger” prototype was tested as a scaled-down model...
-
Effect of preconsolidation on pile bearing capacity in model tests
PublicationBadanie wpływu prekonsolidacji gruntu w badaniach modelowych w komorze kalibracyjnej. Zagęszczone piaski kwarcowe poddano prekonsolidacji przy OCR nie większym od 7. Analiza współczynnika parcia spoczynkowego gruntu. Wpływ wskaźnika prekonsolidacji na nośność podstawy i pobocznicy pali oraz zmiany naprężeń wokół modelu i odkształcenia objętościowe masywu gruntowego.
-
Pale prefabrykowane
PublicationW artykule przedstawiono stan współczesnej technologii pali prefabrykowanych, drewnianych, stalowych, żelbetowych oraz zakres ich stosowania w budownictwie.
-
Centrifuge modelling of tapered wall jacked into dense sand
PublicationA series of static penetration tests of trapezoidal walls in dense Fontainebleau sand were performed in the geotechnical centrifuge at Gustave Eiffel University. The models of wall with three different shapes (straight profile with thickness D=16mm, 0.75 degree and 1.5 degree of taper angle) but with the same volume were used. The soil mass was instrumented with five stress cells located at two levels at 2D, 4D and 6D distance...
-
InGaN trapered laser diodes
PublicationW pracy zaprezentowano rezultaty badan nad diodami laserowymi InGaN ze zwężającym się kanałem. Kąty kanałów zmieniane były w zakresie 2 -5 stopni, jak również zmieniana była długość kanału. Wykazano, że w przypadku optymalnych parametrów, parametr M2 (M kwadrat) opisujący odtępstwa wiązki od krzywej Gaussa, wynosił 2.1 przy mocy optycznej 200 mW.
-
Report of Eurocode 7 application for pile foundation design in Poland
PublicationThe EC7 rules of geotechnical design are in use in Poland for several years, even though there is no National annex. With regard to pile foundations, there are valid EC7 recommendations concerning design approaches, load partial coefficients, correlation coefficients and capacity partial coefficients. Polish designers can be quite flexible when it comes to choose a method for static, bearing capacity and settlement calculations....
-
Large deformation finite element analysis of undrained pile installation
PublicationIn this paper, a numerical undrained analysis of pile jacking into the subsoil using Abaqus software suit has been presented. Two different approaches, including traditional Finite Element Method (FEM) and Arbitrary Lagrangian–Eulerian (ALE) formulation, were tested. In the first method, the soil was modelled as a two-phase medium and effective stress analysis was performed. In the second one (ALE), a single-phase medium was assumed...
-
The analysis of soil resistance during screw displacement pile installation
PublicationThe analysis of soil resistances during screw displacement pile installation based on model and field tests. The investigations were carried out as a part of research project, financed by the Polish Ministry of Science and Higher Education. A proposal of empirical method for prediction of rotation resistance (torque) during screw auger penetration in non-cohesive subsoil based on CPT result.
-
Static load test on concrete pile – instrumentation and results interpretation
PublicationFor some time (since 8-10 years in Poland) a special static load tests on instrumented piles are carried out. Such studies are usually of a scientific nature and provide detailed quantitative data on the load transfer into the ground and characteristics of particular soil layers interaction with a pile shaft and pile base. Deep knowledge about the pile-subsoil interaction can be applied for a various design purposes, e.g. numerical...
-
THE APPLICATION OF PHENOMENOLOGICAL METHODOLOGY FOR DESIGNING PILE FOUNDATION IN PORT STRUCTURES
PublicationIt is of utmost importance in the design process that a suitable, safe and concurrently economic solution be chosen. Issues connected with foundations require adopting a special approach. Soil is a composite medium, and it is essential to describe as precisely as possible the interaction taking place between the subgrade and the structure. There are many design methods of pile foundation that are based on in-situ test of soils....
-
Pale wkręcane ATLAS
PublicationPrzedstawiono praktyczne zastosowanie nowoczesnych, przemieszczeniowych pali wkręcanych typu ATLAS. Omówiono zasady obliczeń tego rodzaju pali, również na podstawie wyników badań sondą CPT. Przykłady posadowień z terenu Polski pozwalają na ocenę mozliwości posadowień w warunkach krajowych.
-
Pale wkręcane ATLAS
PublicationOmówiono nową technologię pali ATLAS. Przedstawiono przykłady zastosowania w odniesieniu do gruntów silnie uwarstwionych. Przedyskutowano metody obliczeń.
-
Prefabrykowane pale wbijane
PublicationOmówiono zastosowanie prefabrykowanych, żelbetowych pali wbijanych w różnych rodzajach budownictwa. Zakres pracy obejmuje dotychczasowe oraz współczesne zastosowania pali prefabrykowanych. Zawarto następujące zagadnienia: materiały do produkcji pali, charakterystykę geometryczną, sposoby łączenia, metody prefabrykacji, metody kontroli, omówiono sprzęt do wbijania, scharakteryzowano zjawiska towarzyszące wbijaniu. Podsumowaniem...
-
Determination of the bearing capacity of pile foundations based on CPT test results
PublicationAnalityczne określanie pełnej krzywej obciążenie - osiadanie na podstawie parametrów geotechnicznych wciąż stanowi bardzo trudne zadanie naukowe i inżynierskie. W pracy przedstawiono metodę bezpośredniego wykorzystania oporów na stożku sondy statycznej do określania pełnej krzywej osiadania dla pali Vibro-Fundex. W sumie jako materiał weryfikacyjny wykorzystano 94 próbne obciążenia statyczne pali.
-
Numerical simulation of screw displacement pile interaction with non-cohesive soil
PublicationA trial numerical simulation of screw displacement pile interaction with non-cohesive subsoil during the transfer of compression load. The simulation was carried out in an axisymmetric system. The technological phases of pile installation in the ground were numerically modelled using equivalent processes which provided similar effects to real technical actions. The results of the numerical calculations were verified by comparing...
-
Static Load Test on Instrumented Pile – Field Data and Numerical Simulations
PublicationFor some time (since 8-10 years in Poland) a special static load tests on instrumented piles are carried out. Such studies are usually of a scientific nature and provide detailed quantitative data on the load transfer into the ground and characteristics of particular soil layers interaction with a pile shaft and pile base. Deep knowledge about the pile-subsoil interaction can be applied for a various design purposes, e.g. numerical...
-
Probabilistic analysis of settlements under a pile foundation of a road bridge pylon
PublicationThe paper addresses the reliability change of a road bridge pile foundation due to the unpredictable increase of settlements in time. The analysis is based on the Rędziński Bridge in Wrocław, Poland, its design assumptions, and monitoring results. The bridge foundation rests on a multi-layered subsoil assumed random. The Finite Element model of the subgrade is generated in ZSoil® software. To simplify the probabilistic approach,...
-
Estimation of Screw Displacement Pile-Bearing Capacity Based on Drilling Resistances
PublicationThis article presents an engineering, empiricalmethod of estimating the bearing capacity and settlementcharacteristics Q-s of screw displacement piles andcolumns, based on soil resistance encountered during thedrilling to form piles/columns in the ground. The methodwas developed on the basis of correlation analyses of thetest results of 24 piles made during the “DPDT-Auger”research project (Krasiński et al., 2022a). In the proposedmethod,...
-
The bile salt content of human bile impacts on simulated intestinal proteolysis of β-lactoglobulin
PublicationThe gastrointestinal hydrolysis of food proteins has been portrayed in scientific literature to predominantly depend on the activity and specificity of proteolytic enzymes. Human bile has not been considered to facilitate proteolysis in the small intestine, but rather to assist in intestinal lipolysis. However, human bile can potentially influence proteins that are largely resistant to gastric digestion, and which are mainly hydrolysed...
-
The sensitiveness of the speed of pile displacement to speed variations of hammer in beating down process
PublicationIn this paper there is presented dynamical system described speed of pile displacement during beating down process. Its response is determined by using Heaviside operator. There is introduced the convergence with regulator in partially ordered space. There is given an answer to the question, whetdisplacement is sensitive to hammer's speed variations.
-
Comparative model tests of SDP and CFA pile groups in non-cohesive soil
PublicationThe research topic relates to the subject of deep foundations supported on continuous flight auger (CFA) piles and screw displacement piles (SDP). The authors have decided to conduct model tests of foundations supported on the group of piles mentioned above and also the tests of the same piles working alone. The tests are ongoing in Geotechnical Laboratory of Gdańsk University of Technology. The description of test procedure, interpretation...
-
Zero-Pole Electromagnetic Optimization
PublicationA fast technique for the full-wave optimization of transmission or reflection properties of general linear timeinvariant high-frequency components is proposed. The method is based on the zeros and poles of the rational function representing the scattering parameters of the device being designed and it is the generalization of the technique developed for the design by optimization of microwave filters. The performance of the proposed...
-
The role of bile salts in digestion
PublicationBile salts (BS) are bio-surfactants present in the gastrointestinal tract (GIT) that play a crucial role in the digestion and absorption of nutrients. The importance of BS for controlled release and transport of lipid soluble nutrients and drugs has recently stimulated scientific interest in these physiological compounds. BS are so-called facial amphiphiles showing a molecular structure that is very distinct from classical surfactants....
-
Numerical estimation of the pile toe and shaft unit resistances during the installation process in sands
PublicationNumerical simulations of a pile jacking were carried out. A Coupled Eulerian–Lagrangian (CEL) formulation was used to treat with large deformation problems. An Abaqus, a commercial Finite Element Method software suit, was used as a computing environment. The Mohr–Coulomb constitutive model was applied and the Coulomb model of friction was used to describe pile-soil interaction. Calculations were made for three different pile diameters....
-
Effects of full displacement pile installation on the stress and deformation state of surrounding soil: review
PublicationSeveral field and model tests have been conducted to investigate the impact of pile installation on bearing capacity. However, little is known about how piles behave during installation, how they interact with the surrounding soil, and how this affects sandy soil properties. This review paper investigates the effect of pile driving on surrounding sandy soil as it compacts sandy soil near to the pile. For this purpose, various related...
-
Lateral load resistance of piled raft foundation - A case study of District Jail, Saidu Sharif, Swat Pakistan
PublicationPiled raft foundations under lateral loads are usually designed as a pile group, ignoring the contribution of the raft to resisting the lateral loads. In this paper, a case study was performed to determine the raft's contribution to the lateral load resistance. This study analyzed a pile-supported reinforced concrete retaining wall for two different foundation conditions, i.e., pile group foundation and pile raft foundation. Pile group...
-
Reliability of disk file organisation for microcomputers
Publication -
Pole pracy układu napędu hydrostatycznego
PublicationPrzedstawiono pole pracy układu napędu hydrostatycznego. Uzasadniono podział parametrów pracy silnika hydraulicznego i pompy na parametry niezależne i zależne od pracy tych maszyn wyporowych i układu z nich utworzonego. Zaproponowano podjęcie tematu badawczego umożliwiającego opracowanie metody wyznaczania charakterystyk energetycznych pomp i silników hydraulicznych obrotowych oraz zmodyfikowanych metod wyznaczania charakterystyk...
-
Bile salts in digestion and transport of lipids
PublicationBecause of their unusual chemical structure, bile salts (BS) play a fundamental role in intestinal lipid digestion and transport. BS have a planar arrangement of hydrophobic and hydrophilic moieties, which enables the BS molecules to form peculiar self-assembled structures in aqueous solutions. This molecular arrangement also has an influence on specific interactions of BS with lipid molecules and other compounds of ingested food...
-
Extremal thermal loading of a bifurcation pipe
PublicationThe subject of considerations is a spherical bifurcation pipe of a live steam made of steel P91, which is an element of a block of coal-fired power plant working with a 18K370 turbine. As experience shows, it is a very sensitive element of the boiler pipelines. An extreme work scenario for such a block has been adopted, in which the turbine is shutting down to a warm state three times in 24 hours. This is an action dictated by...
-
Fotowoltaika - ile to kosztuje?
PublicationArtykuł przedstawia tendencję w zakresie kształtowania się kosztów inwestycji fotowoltaicznych na świecie. Obecnie obserwowane tempo spadku kosztów inwestycyjnych wynosi15% -22% rocznie. Oczekuje się, że nastąpi spadek cen o 70% od obecnego poziomu. Optymistyczne prognozy przewidują długoterminowy spadek kosztów wytwarzania.
-
INFLUENCE OF TIME ON THE BEARING CAPACITY OF PRECAST PILES
PublicationOne of the most popular types of foundations in layered subsoil with very differentiated soil shear strengths are precast piles. One of the reasons is a fact that we can well control the driving process during the installation of these piles. The principles of the assessment of bearing capacity and settlements of the piles given by Eurocode 7, concentrate on two main methods, i.e. Static Pile Load Tests (SPLT) and Dynamic Driving...
-
The use of plate springs for preloading of a system of tapered roller bearings of a wind turbine gearbox
PublicationThe use of preloaded tapered roller bearings in wind turbine drive systems allows a transfer of load in the case of high variations of axial forces. The examined bearing system, a modification of a current design, consists of a pair of different sized bearings. Previous study showed the high sensitivity of tapered roller bearings on the existing radial interference. Dimensional tolerances used in the original design do not allow...
-
Experience gained at the application of Atlas piles in Poland
PublicationAnaliza współpracy pali ATLAS z uwarstwionym podłożem gruntowym na podstawie obliczeń oraz próbnych obciążeń statycznych. Przydatność pali ATLAS w terenach zurbanizowanych.
-
Advanced field investigations of screw piles and columns
PublicationPrzedstawiono opis badań pali i kolumn wkręcanych na terenowym poletku doświadczalnym, wykonanych w ramach projektu badawczego MNiSW. Badania statyczne pali i kolumn wykonano z zaawansowanym systemem do pomiaru rozkładu siły wzdłuż trzonów. Przedstawiono podstawowe wyniki badań z rozdziałem obciążenia na podstawę i pobocznicę pali i kolumn.
-
Wave damping and smoothing in the unsteady pipe flow
Publicationlaboratoryjne eksperymenty wykonane dla rur polietylenowych o różnej długości wykazały obecność takich zjawisk jak zmienna prędkość propagującej fali ciśnienia oraz jej intensywne tłumienie i wygładzanie. w artykule zaproponowano modyfikacje standardowych równań przepływu nieustalonego. polega ona na wprowadzeniu zmiennej prędkości fali oraz dyssypacji energii na jej czole opisanej członem dyfuzyjnym. do rozwiązania równań zaproponowano...
-
Metody oznaczania pestycydów w pyle zawieszonym.
PublicationPył PM (particulate matter) jest jednym z potencjalnych zagrożeń zdrowia wywołanych zanieczyszczeniem powietrza. Zwłaszcza pył respirabilny, inaczej frakcja PM10 (frakcja pyłów o średnicy cząstek mniejszej niż 10 µm), jest uważana za specyficzny rodzaj zanieczyszczeń, ponieważ ten zbiór cząstek może penetrować do obszaru wymiany gazowej w płucach.
-
Zero-Pole Space Mapping for CAD of Filters
PublicationIn this paper, we propose a new space-mapping technique tailored to the CAD of microwave filters. The goal of space mapping is to achieve a satisfactory design with the minimal number of fine model evaluations. In our approach, the filter is represented by a rational function. To quickly align the coarse and fine models, and to speed up the direct optimization of the coarse model, we propose matching the zeros and poles of a rational...
-
Sorption of Chlorinated Solvents on Pine and Oak sawdust
PublicationThe article presents assessment of pine and oak sawdusts as sorbents for removal of chlorinated solvents from water. Sawdusts as potential sorbents were characterized with elemental analysis and BET analyses. Sorption capacity was determined for both pine and oak sawdust towards 1,1,2-trichloroethane, tetrachloroethene and 1,1,1,2-tetrachloroethane. Pine sawdust was able to adsorb greater amounts of chlorinated solvents compared...
-
Modern approaches to file system integrity checking
PublicationOne of the means to detect intruder's activity is totrace all unauthorized changes in a file system.Programs which fulfill this functionality are called fileintegrity checkers. This paper concerns modernapproach to file system integrity checking. It reviewsarchitecture of popular systems that are widely used inproduction environment as well as scientific projects,which not only detect intruders but also take actions tostop their...
-
Polish experience of dynamic tests for bored piles
PublicationPrzedstawiono zastosowanie badań dynamicznych, DLT, do oceny nośności wierconych pali wielkośrednicowych.Na podstawie badań terenowych, dla dwóch obiektów mostowych, wykonano badania dynamiczne (DLT) oraz korelacyjne badania statyczne (ASPLT). Określono pełną krzywą osiadania. Uzyskano dobrą zgodność krzywych obciążenie - osiadanie dla zakresu obciążeń roboczych.
-
Sound intensity distribution around organ pipe
PublicationThe aim of the paper was to compare acoustic field around the open and stopped organ pipes. The wooden organ pipe was located in the anechoic chamber and activated with a constant air flow, produced by an external air-compressor. Thus, long-term steady state response was possible to obtain. Multichannel acoustic vector sensor was used to measure the sound intensity distribution of radiated acoustic energy. Measurements have been...