Search results for: foresters
-
Kinematyczne pomiary GNSS na linii kolei wąskotorowej w Koszalinie
PublicationW artykule opisano metodę kinematycznych pomiarów geodezyjnych GNSS zastosowaną dla inwentaryzacji trasy kolejowej w terenie silnie zalesionym. W badaniach wskazano możliwości wykorzystania tej metody dla inwentaryzacji układu geometrycznego trasy kolei wąskotorowej w Koszalinie. Opisano najważniejsze różnice pomiędzy koleją o rozstawie szyn 1000 mm a 1435 mm oraz przyszłościowe zagadnienie planowanej rewitalizacji tego odcinka....
-
EKOSYSTEM PRZESTRZENI ZAMIESZKIWANIA W UJĘCIU AUTORSKICH POSZUKIWAŃ FORMY DOMU OPARTYCH O KONCEPCJĘ ZGODNOŚCI
PublicationCelem artykułu jest prezentacja efektów projektu autorskiego realizowanego w oparciu o koncepcję zgodności. Przeprowadzone zostały kilkuletnie studia lokalnych uwarunkowań przyrodniczych skutkujących powstaniem zbioru rysunków i rzeźb oraz fotografii dokumentujących ich aranżację in situ. Badania prowadzono na terenie Pojezierza Kaszubskiego w obszarze południowego brzegu Jeziora Wdzydzkiego. Działania artystyczno-projektowe o...
-
Spiral Search Grasshopper Features Selection with VGG19-ResNet50 for Remote Sensing Object Detection
PublicationRemote sensing object detection plays a major role in satellite imaging and is required in various scenarios such as transportation, forestry, and the ocean. Deep learning techniques provide efficient performance in remote sensing object detection. The existing techniques have the limitations of data imbalance, overfitting, and lower efficiency in detecting small objects. This research proposes the spiral search grasshopper (SSG)...
-
Attitudes to tree removal on private properties in two Polish cities.
Open Research DataLarge cities are increasingly faced with declining urban tree cover and related problems, such as increased urban heat islands and flash floods. Reducing these phenomena increasingly has to rely on trees located on private property. However, to effectively engage private landowners on these issues, more attention must be paid to understanding their...
-
Modelling Wetland Growing Season Rainfall Interception Losses Based on Maximum Canopy Storage Measurements
PublicationThis study estimates rainfall interception losses from natural wetland ecosystems based on maximum canopy storage measurements. Rainfall interception losses play an important role in water balance, which is crucial in wetlands, and has not yet been thoroughly studied in relation to this type of ecosystem. Maximum canopy storage was measured using the weight method. Based on these measurements, daily values of interception losses...
-
The influence of IT-competency dimensions on job satisfaction, knowledge sharing and performance across industries
PublicationPurpose – Technology makes knowledge management easier. Knowledge sharing is essential for organizational development. Job satisfaction fosters knowledge sharing. Hence, this study aims to develop an understanding of the mutual relationship between knowledge sharing and job satisfaction when both are predicted by information technology (IT)-competency dimensions such as IT-operations, IT-knowledge and IT-infrastructure in the context...
-
Granulometric characterization of Arctic driftwood sawdust from frame sawing process
PublicationArctic driftwood can be used as an alternative source of wood as construction timber and furniture material, especially in Iceland and Greenland. The use of Arctic driftwood can help in the fight against climate change, by developing land reforestation processes and reducing the volume harvested wood from forests and sustainability of harvesting processes. In this paper the results of an analysis of the effect of long-term residence...
-
NUTCY Nutrients cycling for sustainability
ProjectsProject realized in Department of Process Engineering and Chemical Technology
-
Automatic labeling of traffic sound recordings using autoencoder-derived features
PublicationAn approach to detection of events occurring in road traffic using autoencoders is presented. Extensions of existing algorithms of acoustic road events detection employing Mel Frequency Cepstral Coefficients combined with classifiers based on k nearest neighbors, Support Vector Machines, and random forests are used. In our research, the acoustic signal gathered from the microphone placed near the road is split into frames and converted...
-
Soft Sensor Application in Identification of the Activated Sludge Bulking Considering the Technological and Economical Aspects of Smart Systems Functioning
PublicationThe paper presented the methodology for the construction of a soft sensor used for activated sludge bulking identification. Devising such solutions fits within the current trends and development of a smart system and infrastructure within smart cities. In order to optimize the selection of the data-mining method depending on the data collected within a wastewater treatment plant (WWTP), a number of methods were considered, including:...
-
Tacit knowledge influence on intellectual capital and innovativeness in the healthcare sector: A cross-country study of Poland and the US
PublicationThis study provides empirical proof that whole organizational innovativeness is rooted in tacit knowledge due to its potency of human capital creation and, that a learning culture composed of a learning climate and mistakes acceptance component fosters human capital development. The main practical implication is that if the IC components are externally rather than internally determined in the particular organization embedded in...
-
The Indonesian economy in 2005: An analysis using the input-output approach
PublicationThis study aims to analyze the economic conditions of Indonesia in 2005. This study employs Input-Output (IO) analysis as an analysis instrument. The data of this study is the Indonesian IO table for 2005. Thus, the Indonesian economy is represented by Indonesian industrial sectors mentioned in the data. There are nine industries used in the present study, namely (1) agriculture, livestock, forestry, and fishery, (2) mining and...
-
Point cloud in archaeological and historical survey
PublicationIn the last decade the potential of using the point clouds in archaeological research has been noted. Therefore, a number of guidelines concerning aspects of data acquisition (resolution and format) were developed. They also included the way of searching the imaged area to identify archaeological and historical cultural heritage sites. The purpose of this research was to analyze the point cloud for selected woodland survey. Forest...
-
Monitoring Trends of Land Use and Land Cover Changes in Rajang River Basin
PublicationIn this study, the spatiotemporal changes in land use and land cover (LULC) were evaluated from 1992 to 2015 for the Rajang River Basin (RRB) located in the Sarawak State of Malaysia. The changes in water bodies cropped lands, and forests were assessed based on the available remotely sensed satellite data. Supervised classification with the Maximum-Likelihood-Algorithm technique was adopted for monitoring the LULC changes using...
-
Comparison of berry quality in highbush blueberry cultivars grown according to conventional and organic methods
Publication -
Improving methods to calculate the loss of ecosystem services provided by urban trees using LiDAR and aerial orthophotos
PublicationIn this paper we propose a methodology for combining remotely sensed data with field measurements to assess selected tree parameters (diameter at breast height (DBH) and tree species) required by the i-Tree Eco model to estimate ecosystem services (ES) provided by urban trees. We determined values of ES provided by trees in 2017 in Racibórz (a city in South Poland) and estimated the loss of ES from January 1, 2017 to March 5, 2017,...
-
High-Resolution Discharge Forecasting for Snowmelt and Rainfall Mixed Events
PublicationDischarge events induced by mixture of snowmelt and rainfall are strongly nonlinear due to consequences of rain-on-snow phenomena and snowmelt dependence on energy balance. However, they received relatively little attention, especially in high-resolution discharge forecasting. In this study, we use Random Forests models for 24 h discharge forecasting in 1 h resolution in a 105.9 km 2 urbanized catchment in NE Poland: Biala River....
-
Design-oriented computationally-efficient feature-based surrogate modelling of multi-band antennas with nested kriging
PublicationDesign of modern antenna structures heavily depends on electromagnetic (EM) simulation tools. EM analysis provides reliable evaluation of increasingly complex designs but tends to be CPU intensive. When multiple simulations are needed (e.g., for parameters tuning), the aggregated simulation cost may become a serious bottleneck. As one possible way of mitigating the issue, the recent literature fosters utilization of faster representations,...
-
Synthesis and characterization of biopolyols through biomass liquefaction of wood shavings and their application in the preparation of polyurethane wood composites
PublicationThe sustainability of production systems in wood processing, wood industry, and wooden waste disposal is an important issue for European industry and society. Proper development of products based on renewable wood resources gives an opportunity to provide materials with long-term environmental, social, and economic sustainability. This study aims to establish a new way of forestry and agricultural waste materials utilization by...
-
Providing Public Space Continuities in Post-Industrial Areas through Remodelling Land/Water Connections
PublicationThis article examines the problem of urban transformation strategies applied in recent years which are based on the creation of new water areas and modification of existing ones. The research is an attempt to prove that modifications of plans of water areas and forms of their borders may play an important role in achieving the best quality public spaces in post-industrial territories. The basis for demonstrating the importance...
-
Bibliometric analysis of artificial intelligence in wastewater treatment: Current status, research progress, and future prospects
PublicationWastewater treatment is an important topic for improving water quality and environmental protection, and artificial intelligence has become a powerful tool for wastewater treatment. This work provides research progress and a literature review of artificial intelligence applied to wastewater treatment based on the visualization of bibliometric tools. A total of 3460 publications from 2000 to 2023 were obtained from the Web of Science...
-
Application of autoencoder to traffic noise analysis
PublicationThe aim of an autoencoder neural network is to transform the input data into a lower-dimensional code and then to reconstruct the output from this code representation. Applications of autoencoders to classifying sound events in the road traffic have not been found in the literature. The presented research aims to determine whether such an unsupervised learning method may be used for deploying classification algorithms applied to...
-
Knowledge sharing and knowledge hiding in light of the mistakes acceptance component of learning culture- knowledge culture and human capital implications
PublicationPurpose: This study examines the micromechanisms of how knowledge culture fosters human capital development. Method: An empirical model was developed using the structural equation modeling method (SEM) based on a sample of 321 Polish knowledge workers employed in different industries. Findings: This study provides direct empirical evidence that tacit knowledge sharing supports human capital, whereas tacit knowledge hiding does...
-
Psychological capital and happiness at work: The mediating role of employee thriving in multinational corporations
PublicationWorking in multicultural work environments of multinational corporations (MNCs) creates challenges whose expected impact on happiness is equivocal. In the following paper, we examine the relationship between psychological capital and happiness at work in the specific MNCs’ context. We assume that thriving (eudemonic well-being) at work fosters individuals’ development and enhances their happiness composed of both the affective...
-
ECONUT Eco-designing for the coastal zone nutrient's circularity
ProjectsProject realized in Department of Process Engineering and Chemical Technology
-
Determination of Moisture Content Profiles of Spruce Wood After High Temperature Process and Air Drying
PublicationThe results of moisture content of wood after the process of its drying under high temperature conditions and air drying are presented. Wood samples, namely spruce (Picea abies Karst.) from the northern part of Pomerania region in Poland, were subject of steam and air drying.The aim of experiments was to measure moisture content of wood in its cross sections using moisture meter WRD-100. The samples of thickness 70 mm and length...
-
The differential impact of a density of Polish pine wood on cutting forces with its origin region taken into consideration
PublicationIn the article the dependence of cutting forces in a function the density of wood with regard to the wood origin are presented. Samples used in experiment were with Scotch pine (Pinus sylvestris L.) originating from four provenances in Poland (Figure 1). Wood density was measured by two methods: stereometric method (global density) and radiometric method (local density). Stereometric method consists in measurements the volume...
-
Dynamics of cutting power during sawing with circular saw blades as an effect of wood properties changes in the cross section
PublicationIn the paper the effect of the method calculation upon the cutting power is presented. In computations were used models in which fracture toughness was incorporated. The comparison concerned models as follows: FM-CM – classic model in which the sum of all uncut chip thicknesses of the simultaneously teeth engaged represented the mean uncut chip thickness, FM-FDM – full dynamical model in which besides variable uncut chip thickness...
-
The methodology for determining of the value of cutting power for cross cutting on optimizing sawing machine
PublicationIn the article the methodology of forecasting the energy effects of the cross-cutting process using the classical method, which takes into account the specific cutting resistance, is presented. The values of cutting power for the cross-cutting process of two types of wood (softwood and hardwood) were forecasted for the optimizing sawing machine with using presented methodology. The cross-cutting process with high values of feed...
-
Simulation of wood structure geometry after machining
PublicationW niniejszym artykule została przedstawiona nowa metoda trójwymiarowych symulacji geometrii powierzchni drewna. Zaprezentowano wpływ parametrów obróbkowych oraz drgań podczas strugania obrotowego drewna. Chropowatość powierzchni była charakteryzowana poprzez parametry profilu chropowatości Ra oraz Rz. Posuw na ostrze oraz średnica narzędzia są najbardziej wpływającymi czynnikami na wielkość nierówności podczas maszynowej obróbki...
-
Influence of steam drying process on wood mechanical properties
PublicationResults of influence of gas-steam mixture drying process on mechanical properties of material are presented. Wood species, namely oak (Quercus L.), beech (Fagus L.), pine (Pinus L.) and spruce (Picea K.) from the northern part of Pomerania region in Poland, were subject of air-steam mixture drying process in a laboratory kiln especially arranged for that reason. Measurements of the global coefficient of elasticity and bending strength...
-
The effect of the annual growth and the late wood share upon density of the Polish pine wood as a function of its origin
PublicationW artykule przedstawiono zróżnicowanie gęstości polskiego drewna sosnowego (Pinus sylvestris L.) w zależności od udziału drewna późnego w przyroście rocznym z uwzględnieniem krainy pochodzenia drewna. Wspomniane zróżnicowanie jest w istotne statystycznie w skali globalnej oraz dla większości miejsc pochodzenia. Pomiar gęstości wykonano przy użyciu metody stereometrycznej. Metoda ta polegała na określeniu objętości pryzmy poprzez...
-
The innovative experimental rig for wood steam drying at atmospheric pressure
PublicationThe high cost of fossil fuel and soaring consumer interest have encouraged people in the wood industry to look for faster and more energy-efficient methods to dry lumber. The air-steam mixture as medium of drying process was used in a laboratory kiln especially arranged for that reason. Experimental rig is based on automatic control system. At the time of drying measurements of the internal temperature, wood temperature, moisture...
-
The lasting traditions of activities in the field of wood technology researches at the Gdansk University of Technology
PublicationW niniejszym artykule przedstawiono sylwetki ludzi z Politechniki Gdańskiej, którzy odeszli, jednakowoż, których działalność była znacząca w obszarze drzewnictwa i mechanicznej technologii drewna.
-
On some approaches to cutting power estimation while wood sawing
PublicationW niniejszym artykule przedstawiono i porównano metody, które mogą być stosowane do szacowania mocy skrawania przy przecinaniu drewna na pilarkach tarczowych. Przy klasycznym podejściu efekty energetyczne procesu przecinania drewna piłami są obliczane na bazie właściwego powierzchniowego oporu skrawania. W internecie dostępne są narzędzia do określania mocy skrawania w postaci oprogramowania dostępnego on-line, przykładowo "Horsepower...
-
The influence of the drying process on the deformation of the beech and oak wood samples
PublicationThe influence of the drying process conditions on the deformation of the beech and oak wood. The results of the deformation of beech wood (Fagus sylvatica L.) and oak wood (Quercus robur) after drying process are presented. The drying process was carried out in the same drying schedule for each wood species. During each of schedules 40 pieces of wood were dried. The samples were divided into two groups. The first group of tested...
-
Cutting power estimation of the bandsawing process of beech wood (Fagus sylvatica L.) dried in three operating modes
PublicationIn this paper the predicted values of cutting power for bandsawing machine (ST100R, f. Stenner), which is located at the sawmill company Complex in Dziemiany, were presented. The values of cutting power were forecasted for beech wood (Fagus sylvatica L.), from the northern part of Pomerania region in Poland, which was dried in three operating modes: BKP - air drying at 25oC, BKS - air-steam mixture drying at 80oC, BKW - steam drying...
-
The forecasted values of cutting power for sawing on band sawing machines for Polish Scots pine wood (Pinus sylvestris L.) in a function of its provenance.
PublicationIn this paper the predicted values of cutting power for band sawing machine (EB 1800, f. EWD), which is used in the Polish sawmills, were showed. The values of cutting power were forecasted for Scots pine (Pinus sylvestris L.) wood of five provenances from Poland. These values were determined using an innovative method of predicting the cutting power, which takes into account of elements of fracture mechanics. The resulting predictions...
-
Application in circular sawing machines of the experimental results of investigations of the chip removing system operation
PublicationThe experimental results of the chip removing system operation are presented. The main aim of them was to optimize suction system of the panel saw Fx3 and its follower Fx550. The attention was focused on the upper casing, which was the part of removing system. Within the framework of the work a systematic experimental study of pressure distribution in the casing during operation of the selected rotational speed of saw blade with...
-
The reduction of vibrations in circular sawing machines
PublicationThe presented in this paper the main objectives of the research were to explore vibrations signals of the main spindle system, the machine tool body and a circular saw to extract informative features for assessment of the designs of the panel saw Fx3 and its follower Fx550.Even though the main spindle of the new table sliding saw Fx550 has its rotational speeds larger about 20% in comparison to the Fx3, peak values of the vibrational...
-
Criteria for assessment of pine wood surfaces after planing
PublicationThe arise of defects in raw material as well as a machined part in most cases causes need to qualify the final product (wooden frames) as a scrap part or an additional work activity must be done. In the paper selected results of the effect of the material defects on the surface quality of the elements after planing and painting are presented. The materials under production were glulam elements of pine wood. Research experiments...
-
Surface texture of pine wood beams after planing in industrial conditions
PublicationMeasuring the surface features of wooden components after planing is connected with the rising demands regarding to the quality of the painted window frames. In the paper the complex surface texture analysis especially identifying of surface damages using non-contact 3D measurement techniques for precise area measurement were presented.This enabled the study of irregular surface features with sufficient fidelity and resolution....
-
The effect of a belt position in the spindle driving system on critical rotational speeds
PublicationThe aim of this paper was to examine how the belt pulley position affects critical rotational speeds of the modernized spindle of the sliding table saw Fx3. Methodology of determination of critical rotational speeds of the spindle in a function of the spindle design features and its driving system is presented. Spindles in these kind of machine tools are mainly driven with V-belts, and the pulleys on the spindles might be positioned:...
-
An assessment of teeth quality of the mini gang saw blade
PublicationIn this work, the assessment of the effect of the operating time (90 min.) of the mini gang saw blades during sawing Scotch pine (Pinus sylvestris L.) samples upon changes of the saw blade teeth sharpness (bluntness), which was defined as an effective radius of the nose ρ , has been described. The research activities have been carried out on the Nikon Ti-S optical microscope equipped with the Nikon DS-30W camera allowing high-speed...
-
Comparison of natural frequencies of a circular saw blade obtained empirically and with FEM
PublicationThe knowledge of the natural frequencies’ values of circular saw blades is necessary to determine the minimal critical rotational speed in which they can work with required stability. Moreover, testing the circular saw blades with more complicated shapes, e.g. which have additional holes inside blades for cleaning knifes or additional indirect teeth in gullets, reveals some kind of problematic properties of these saw blades. The...
-
The dying medium temperature impact on the final moisture content of pine wood at constant drying time
PublicationThe results of final moisture content of pine wood (Pinus sylvestris L.) after drying process are presented. The wood in the experiments was taken from the northern part of Pomeranian region in Poland. The drying process was performed in the experimental chamber equipped with the micro-jet heat exchanger. The air at temperatures of 40°C, 60°C, 80°C, 100°C and 120°C with relative humidity about 60% and atmospheric pressure was the...
-
The low temperature waste heat recovery in drying process of pine wood using micro-jet heat exchanger
PublicationThe article presents the influence of the drying medium temperature changes for the relative and absolute moisture content values during pine wood drying. The drying process was conducted at constant atmospheric pressure and with different drying medium (air) temperature levels, respectively: 40oC, 60oC, 80oC, 100oC, and 120oC. In order to develop a method that would enable low temperature drying of solid materials the experiments...
-
Distinctive properties of Scots pine (Pinus sylvestris L.) originating from the Carpathian and Great Poland-Pomeranian of Nature and Forest Land
PublicationIn this paper values of properties of Scots pine, the fracture toughness and of shear yield stress in the shear zone are presented. Samples of Scotch pine (Pinus sylvestris L.) wood of two provenances from Poland were tested. These properties were determined from the values of cutting power obtained experimentally on the saw frame PRW-15M. The values of fracture toughness and shear yield stress based on the Atkins model for cutting...
-
The selected effects of high temperature air-steam mixture wood drying
PublicationThe results of properties change of beech wood after drying process are presented. The wood taken to experiments was from northern part of Pomeranian region in Poland. Before the main high temperature drying process using air-steam mixture, wood was initially dried in an open air conditions. The high temperature drying process was conducted at temperature 120oC, humidity 48%, flow rate of drying medium 2.5m/s and atmospheric pressure....
-
The effect of current signal filtering method on the value of cutting power while sawing wood
PublicationThe goal of this work was to investigate an effect of various signal pre-processings on the outline of the electrical power curve and its influence on the measured cutting force estimation. Two signal processing methods were selected for the needs of the experiment, including digital filter and wavelet transform. The filter used was Butterworth, 3rd order band-stop with the cut-out band from 45 Hz to 55 Hz. The second approach...