Filters
total: 3088
-
Catalog
displaying 1000 best results Help
Search results for: meat authentication
-
Influence of metallic porous microlayer on pressure drop and heat transfer of stainless steel plate heat exchanger
PublicationThe experimental analysis of passive heat transfer intensification in the case of plate heat exchanger has been carried out. The metallic porous layer was created on the heat transfer surface of analyzed unit. The experiment was accomplished in two stages. In the first stage the commercial stainless steel gasketed plate heat exchanger was investigated, while in the second one – the identical heat exchanger but with the modified...
-
Experimental study on single phase operation of microjet augmented heat exchanger with enhanced heat transfer surface
PublicationThe article presents experimental investigations on a prototype heat exchanger. Presented research is focused on combined active and passive enhancement techniques of surface modification and microjet impingement. The results were compared to reference plate heat exchanger without microjet impingement. The Wilson plot method was applied to determine the heat transfer coefficients in the single phase operation. The heat exchanger...
-
Parametric study of fluid flow and heat transfer over louvered fins of air heat pump evaporator
PublicationTwo-dimensional numerical investigations of the fluid flow and heat transfer have been carried out for the laminar flow of the louvered fin-plate heat exchanger, designed to work as an air-source heat pump evap- orator. The transferred heat and the pressure drop predicted by simulation have been compared with the corresponding experimental data taken from the literature. Two dimensional analyses of the louvered fins with varying...
-
Thermodynamic and geometrical characteristics of mixed convection heat transfer in the shell and coil tube heat exchanger with baffles
PublicationThe article presents passive heat transfer enhancement method in the form of baffles to increase the energy efficiency of the shell coil heat exchanger. Conducted literature review shows that, despite numer- ous studies, there is little work on the intensification of heat transfer at the shell side. Most of the work focuses on the impact of geometrical parameters of the coil itself. This article successfully proves that it is possible...
-
Heat transport in the membrane distillation process
Publication -
Numerical determination of heat exchanger response
PublicationPrzedstawiono metodę przybliżonego obliczania temperatury płynu w ustalonym punkcie wymiennika ciepła i w ustalonej chwili. Wykorzystując nieklasyczny rachunek operatorów można wyznaczyć wzór na odpowiedź wymiennika ciepła, w którym występuje m.in. całka funkcji jednej zmiennej. Do obliczenia wartości całki dla ustalonych parametrów zastosowano wzory Newtona - Cotesa. Podano również oszacowanie błędu przybliżonego obliczania wartości...
-
Molecular Modeling of Meta II Rhodopsin
Publication -
Simplified modelling of heat transfer in groundwater
PublicationPrzenoszenie ciepła w wodach podziemnych jest skomplikowanym, przestrzennym procesem. Z tego względu do rozwiązywania zadań praktycznych celowe jest konstruowanie modeli uproszczonych. W pracy zaproponowano sposób formułowania modelu dwuwymiarowego. Został on pozytywnie zweryfikowany na przykładzie badania przyczyn strat energii cieplnej w elektrowni Kozienice.
-
Modelling of heat transfer in flow boiling
PublicationW pracy przedstawiono zagadnienia związane z modelowaniem wrzenia w przepływie w kanałach o małej średnicy. Przedstawiono modyfikację rozwijanej przez autorów korelacji umożliwiającej wyznaczanie współczynnika przejmowania ciepła podczas wrzenia w przepływie.
-
Heat transfer of two-interacting microjets
PublicationThe present paper paid particular attention to the flow and heat transfer performance for two microjets impinging upon the heated surface by means of experimental investigations.
-
Projecting procedure for meta-material fiber
PublicationWe would like to show new way of derivation evolution equation for short pulses in dielectric waveguide including one model of metamaterial waveguide. This derivation model rely on projecting to the orthogonal basis. In our case to orthogonal basis for cylindrical waveguide.
-
Combined Heat & Power Generating Systems
PublicationSteam cycles in combined heat and power plants. Efficiency of combined heat and power systems. Characteristics of steam-turbine CHP plants. Choice of equipment in CHP generating systems. Economic effects of combined heat and power production. Costs and energy produced CHP generating systems. Future development trends in CHP generating systems.
-
The low temperature waste heat recovery in drying process of pine wood using micro-jet heat exchanger
PublicationThe article presents the influence of the drying medium temperature changes for the relative and absolute moisture content values during pine wood drying. The drying process was conducted at constant atmospheric pressure and with different drying medium (air) temperature levels, respectively: 40oC, 60oC, 80oC, 100oC, and 120oC. In order to develop a method that would enable low temperature drying of solid materials the experiments...
-
Utilisation of waste heat from the power plant by use of the ORC aided with bleed steam and extra source of heat
PublicationUtilization of waste heat recovered from the exhaust gases of the power generation unit by means of ORC (organic Rankine cycles) installation is considered. The waste heat is available in the form of a stream of hot water having temperature of 90 stC in the amount of 200 MWt. To increase evaporation temperaturę of ORC working fluid the heat of steam from the extraction points from the low-pressure part of steam turbine is used....
-
Experimental investigation of heat transfer enhancement in straight and U-bend double-pipe heat exchanger with wire insert
PublicationIn this paper, the possibility of heat transfer enhancement in the U-bend exchanger was presented. Experimental research has been carried out for four individual heat exchanger constructions i.e. plain tube in tube, turbulized tube in tube, plain U-bend and U-bend with turbulator. Also, heat transfer experiments for various boundary conditions were performed to obtain reference values. In case of U-bend exchanger with and without...
-
Performance analyses of helical coil heat exchangers. The effect of external coil surface modification on heat exchanger effectiveness
PublicationThe shell and coil heat exchangers are commonly used in heating, ventilation, nuclear industry, process plant, heat recovery and air conditioning systems. This type of recuperators benefits from simple construction, the low value of pressure drops and high heat transfer. In helical coil,centrifugal force is acting on the moving fluid due to the curvature of thetube results in the development. It has been long recognized that the...
-
Comparison of Antioxidant Activity of Protein Isolates Derived from Selected Dry-Cured Meat Products
Publication -
Potential of bacteriocins from lab to improve microbial quality of dry-cured and fermented meat products
Publication -
Abuse or contamination? Ratio determination of clenbuterol enantiomers to distinguish between doping use and meat contamination
PublicationClenbuterol has been detected in urine of several athletes during routine doping control in the past years. Athletes claimed that the clenbuterol was ingested by eating contaminated meat. Providing analytical prove for this claim is difficult. clenbuterol consists of two enantiomers, R(-) and S(+)-clenbuterol. Currently available human and veterinary preparations were found to consist of a racemic mixture of both enantiomers. When...
-
Poultry meat freshness evaluation using electronic nose technology and ultra-fast gas chromatography
PublicationTo ensure that chicken meat products are safe to consume, it is important to be able to reliably determine its shelf-life. To assess the applicability of ultra-fast gas chromatography and electronic nose technology in evaluation of poultry, an analysis of the headspace of ground chicken meat samples refrigerated over a period of 7 days was performed. Chemometric techniques were used to mine additional information from a multiparametric...
-
SiC coating in ring-on-ring sliding with saline solution (0.9%) lubrication 5MPa, 0.1m/s specimn. #B37/#A35
Open Research DataWear tests in sliding friction of SiC coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, SiC over SiC . Mean contact stress: 5MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: SALINE SOLUTION (0.9%). Tribometer: PT-3. Overall test time till coating penetration 3 min.Secimen...
-
TiC coating in ring-on-ring sliding with saline solution (0.9%) lubrication 5MPa, 0.1m/s specimn. #A39/#B41
Open Research DataWear tests in sliding friction of TiC coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, TiC over TiC . Mean contact stress: 5MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: SALINE SOLUTION (0.9%). Tribometer: PT-3. Overall test time till coating penetration 3 min.Secimen...
-
SiC coating in ring-on-ring sliding with saline solution (0.9%) lubrication 5MPa, 0.1m/s specimn. #A35/#B37
Open Research DataWear tests in sliding friction of SiC coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, SiC over SiC . Mean contact stress: 5MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: SALINE SOLUTION (0.9%). Tribometer: PT-3. Overall test time till coating penetration 3 min.Secimen...
-
Design and Thermodynamic Analysis of Waste Heat-Driven Zeolite–Water Continuous-Adsorption Refrigeration and Heat Pump System for Ships
Publication -
Pro-death signaling of cytoprotective heat shock factor 1: upregulation of NOXA leading to apoptosis in heat-sensitive cells
Publication -
Cattaneo–Christov heat flow model for copper–water nanofluid heat transfer under Marangoni convection and slip conditions
PublicationThis report is devoted to the study of the flow of MHD nanofluids through a vertical porous plate with a temperature-dependent surface tension using the Cattaneo–Christov heat flow model. The energy equation was formulated using the Cattaneo–Christov heat flux model instead of Fourier’s law of heat conduction. The Tiwari–Das model was used to take into account the concentration of nanoparticles when constructing the momentum equation....
-
Co-simulation strategy of transient CFD and heat transfer in building thermal envelope based on calibrated heat transfer coefficients
PublicationThe paper presents a strategy to develop a fully transient numerical model of a heat transfer in building, using a transient CFD model of indoor air and a thermal envelope model, running in a co-simulation. The strategy relies on the utilization of RANS with a high-Re turbulence model and a wall function, which enables to use a coarse computational mesh limiting the computational time. Since wall functions give invalid heat transfer...
-
Edge effects for heat flux in fibrous composites
Publication -
Microphone placement through meta-heuristic algorithms
Publication -
A study of flow boiling heat transfer in minichannels
PublicationW pracy przedstawiono badania eksperymentalne wrzenia w przepływie w minikanale o średnicy wewnętrznej 2.3mm i długości 38cm. Uzyskano rozłady temperatury wzdłuż ścianki kanału oraz lokalne współczynniki przejmowania ciepła. Dane skorelowano z korelacją półempiryczną uzyskując zadowalającą zgodność.
-
Impacts of salvage logging on biodiversity: A meta-analysis
Publication -
Does one currency mean one price?
PublicationEuropean Monetary Union was expected to have many consequences for the economies of participant countries. Theory suggested that through a higher volume of trade and stronger competition in the Eurozone, a single currency would lead to a reduction in price dispersion. As far as prices are concerned, two effects were expected: an immediate effect due to the technical characteristics of the changeover process, and a long-term one...
-
Heat transfer phenomena of glassy carbon foams
Publication -
Network heat is the comfort in winter and summer - TRIGENERATION
PublicationPrzedstawiono międzynarodowe uwarunkowania prawne oraz techniczne stosowania kogeneracji w aspekcie wykorzystania ciepła sieciowego na potrzeby ogrzewania i klimatyzacji obiektów.
-
Does low price mean high competitiveness
PublicationWe found a strong positive relationship between Comparative Price Level Index (CPL) and Growth Competitiveness Index (GCI). We do realize that the relation we have found does not have to indicate cause and effects relationship. Competitiveness is a process which goes far beyond price level but it is detemined by lots of different elemnts. We show the GCI composition that provides a concept explaining what exactly determines competitiveness...
-
Transient operation analysis of a regenerative heat exchanger.
PublicationReferat dotyczy problemu niestacjonarnej pracy wymiennika regenearcyjnego.Przedstawiono w nim uproszczony model matematyczny pozwalający oszacować w sposób ilościowy wielkość stałych czasowych wymiennika.
-
Modelling of convective heat transfer in flow boiling.
PublicationW pracy przedstawiono rozważania dotyczące modelowania przepływu z wrzeniem w zastosowaniu do kanałów o małej średnicy. Stwierdzono,że stosowanie korelacji obowiązujących dla średnic konwencjonalnych nie sprawdza się z praktyką w przypadku małych średnic.
-
Natural convective heat transfer from isothermalconic
PublicationTheoretical considerations on convective heat transfer from isothermal upward conicalsurfaces have been presented. The physical model of this phenomenon consists of an isothermalcone of inclination angle (φ) between the cone generating line (X) and the radius (R) of the cone base. The angle is a parameter of conical surface which varied from (φ = 0−circular horizontal plate) to (φ = π/2—vertical cylinder) . Onthe basis of Navier–Stokes...
-
Heat transfer augmentation using liquid crystal
PublicationPraca przedstawia zastosowanie techniki wizualizacji ciekłokrystalicznej dobadań wymiany ciepła na płaskiej powierzchni z zaburzaczami. Folia ciekło-krystaliczna została umieszczona na powierzchni, aby określić przebieg izoterm. Obraz rejestrowano kamerą JVC, a następnie analizowano komputerowo. Procedura eksperymentalna pozwala na otrzymanie pełnej informacji dotyczącej wymiany ciepła (na powierzchni płaskiej z elementami ustawionymi...
-
The impact of nozzle configuration on the heat transfer coefficient
Publication -
Green function diagonal for a class of heat equations
PublicationA construction of the heat kernel diagonal is considered as element of generalized zeta function theory, which gradient at the origin defines determinant of a differential operator in a technique for regularizing quadratic path integral. Some classes of explicit expressions of the Green function in the case of finite-gap potential coefficient of the heat equation are constructed. An algorithm and program for Mathematica are presented...
-
Thermohydraulic maldistribution reduction in mini heat exchangers
PublicationA detailed numerical investigation has been carried out to analyze the flow maldistribution in 50 parallel 1 mm × 1 mm rectangular minichannels and 1 mm depth minigap section with rectangular, trapezoidal, triangular or concave manifolds in Z-type flow configuration. The working medium was ethanol and the mass flow rate was 5 × 10−4 kg/s. Both sections were heated from the bottom side. Heat flux of 10 000 W/m2 and 5000 W/m2 was...
-
Modelling of heat transfer in supercritical pressure recuperators
PublicationIn the paper presented is analysis of convective flow heat transfer at supercritical pressure in channels of heat exchanger working in the thermodynamic cycle. The modelling is based on the division of the flow into three regions, namely the heavy fluid, a two phase flow consisting of the heavy and light fluids and finally the light fluid flow. Modelling is concentrated on the region of simultaneous flow of two fluids divided into...
-
Cargo ships heat demand - operational experiment
PublicationThe paper presents the results of an experiment conducted on two cargo ships – a 5300 TEU container with a steam heating system and a 7500 dwt general cargo ship with a thermal oil system. On both ships research has been carried out using specially designed measuring equipment. After gathering data about flow velocity and temperatures (steam/ cooling water/ thermal oil/ seawater/ outside air), calculations have been done, resulting...
-
Potential of bacteriocins from lab to improve microbial quality of dry-cured and fermented meat products [pdf]
Publication -
Meat products Brassica exploiting anticarcinogenic potential of cabbage phytochemicals: Polish path to bio-inspired foods
PublicationBadania populacyjne ostatnich dwóch dziesięcioleci wskazują na sposób odżywiania jako jeden z głównych czynników zagrożenia chorobami cywilizacyjnymi, z nowotworami włącznie. W przypadku chorób nowotworowych głównym elementem diety sprzyjającej kancerogenezie jest czerwone mięso. Ze względu na wartość odżywczą i powszechność spożycia produktów mięsnych, poprawienie ich wartości żywieniowej staje się problemem o istotnym znaczeniu...
-
The influence of moderate pressure and subzero temperature on the shelf life of minced cod, salmon, pork and beef meat
PublicationThe effect of moderate pressure at subzero temperature on natural microflora of minced cod, salmony, pork and beef meat was studied. Pressure of 193 MPa at –20 °C caused reduction of total bacterial count in pork and beef meat by 1.1 and 0.6 log cycles, respectively, and by about 1.5 log cycles in fish meat. Under these conditions the psychrophilic and psychrotophic bacteria were below the detection limit (<10CFU/g of sample) in...
-
The Staged Combustion of Meat-and-Bone Meal:The Characteristics of Conversion Sub-processes and Large-Scale Process Outputs
Publicationt Organic waste has been playing an increasingly important role in the energy market as those that may support the economies in pursuing towards decarbonization by increasing the share of renewables in the overall energy balance. In this group of alternative fuels, meat-and-bone meals being a post-production waste of the steadily developing meat industry, constitute a considerable proportion. Though they are rich in minerals, their...
-
Changes in enzymatic activity of fish and slaughter animals meat after high pressure treatment at subzero temperatures
PublicationThe aim of this study was to determine changes in the activity of proteolytic enzymes and transglutaminase of fish and mammal meat after pressurization at subzero temperatures. The activity was measured at the optimal pHs determined for enzymes from particular types of tested meat. It was found that increasing the pressure in the range of 60–193 MPa, did not change significantly the activity of acidic proteases of cod flesh, while...
-
An experimental investigation on the effect of new continuous core-baffle geometry on the mixed convection heat transfer in shell and coil heat exchanger
PublicationIn the article, the authors presented the influence of continuous core-baffle geometry at mixed convection heat transfer in shell and coil heat exchanger. Experiments were carried out for a large power range, i.e. from 100W to 1200W and mass flow rates ranging from 0.01 kg/s to 0.025 kg/s. During the experiments, the mass flow rate of cooling water, the temperature of water at the inlet and outlet as well as the wall temperature...