Filters
total: 4100
displaying 1000 best results Help
Search results for: DISORDERED ALLOYS
-
Evaluation of drawability of tailor-welded blanks made of titanium alloys Grade 2 || Grade 5
Publication -
Structure and thermoelectric properties of Bi–Te alloys obtained by novel method of oxide substrates reduction
PublicationA novel method of thermoelectric materials fabrication has been developed. Oxide reagents have been melted at high temperature in air, quenched, milled to powder and reduced in hydrogen to form Bi–Te alloys. Structural and thermoelectric properties of samples have been investigated depending on initial composition and temperature of reduction process. Sample 25Bi2O3–75TeO2 reduced at 340 °C for 10 h has been found to be a p-type...
-
Microstructure and corrosion properties of the (Mn-N-O-P) type layers created on aluminium alloys
PublicationPrzedstawiono mikrostrukturę i właściwości korozyjne warstw powierzchniowych typu (Mn-N-O-P) wytworzonych na stopach aluminium. Wykazano, iż warstwy (Mn-N-O-P) podwyższają wielokrotnie odporność korozyjną stopów aluminium i mogą być stosowane jako warstwy ochronne na tych materiałach.
-
Fabrication, Microstructure and High Temperature Corrosion Resistance of Porous Alloys for Solid Oxide Fuel Cells
PublicationPorous alloys find use in modern Solid Oxide Fuel Cells as the supporting structures. As they are exposed to high temperatures (> 500°C) an oxide scale forms on their surface due to high temperature corrosion phenomena. Since the ratio between the surface area and volume is much higher than for planar samples, formation of the oxide can lead to a breakaway oxidation after relatively short times. Therefore corrosion properties of...
-
Investigation of corrosion behavior of 6060 and 6082 aluminum alloys under simulated acid rain conditions
PublicationInstantaneous impedance changes of 6060 and 6082 type aluminum alloys in pure water, and simulated acid rain poured into the pure water was investigated by dynamic electrochemical impedance spectroscopy (DEIS). In this way, the influence of aluminum content on the corrosion behavior of 6060 and 6082 type aluminum alloys immersed in simulated acid rain was determined. The corrosion rate of the alloy decreased with increasing Al...
-
Mateusz Kopec Dr hab. inż.
PeopleHead of the Materials and Structural Testing Laboratory in Institute of Fundamental Technological Research PAS and Academic visitor in Imperial College London. Lecturer and Master/PhD students supervisor in Doctoral School of IPPT PAN and TIB PAN, and Imperial College London. Member of Polish Materials Science Society, Member of the Board of Polish Society of Theoretical and Applied Mechanics, and Council Member of the European...
-
Laser Welding of UNS S33207 Hyper-Duplex Stainless Steel to 6061 Aluminum Alloy Using High Entropy Alloy as a Filler Material
PublicationThe high entropy alloy (HEA) filler used during the fabrication method determines the reliability of HEAs for steel-aluminum dissimilar alloy configuration. HEAs have a direct impact on the formation of intermetallic compounds (IMC) formed by the interaction of iron (Fe) and aluminum (Al), and influence the size of the joint’s interaction zone. A novel welding process for Fe-Al alloy joints was developed to prevent the development...
-
“OUT OF PLACE” IN THE CITY: DEVELOPMENT OF SOCIOSPATIAL DISORDER SENSITIVITY SCALE IN URBAN SETTINGS
Publication -
From Emotional Intelligence to Self-Injuries: A Path Analysis in Adolescents With Conduct Disorder
Publication -
Deep brain stimulation in obsessive-compulsive disorder – case report of two patients
Publication -
Context of Digitalized Employment for Older Adults with Autism Spectrum Disorder in the New Normal
PublicationEmployers are actively considering how to normalize remote work technology across different industries. The residual risk of coronavirus disease-19 (COVID-19) will necessarily lower the bar for allowing some workers to stay remote on a more permanent basis. This is based on the realization that many essential jobs can be teleworked while retaining or enhancing productivity. The decisions employers make regarding future work arrangements...
-
Robot-Based Intervention for Children With Autism Spectrum Disorder: A Systematic Literature Review
PublicationChildren with autism spectrum disorder (ASD) have deficits in the socio-communicative domain and frequently face severe difficulties in the recognition and expression of emotions. Existing literature suggested that children with ASD benefit from robot-based interventions. However, studies varied considerably in participant characteristics, applied robots, and trained skills. Here, we reviewed robot-based interventions targeting...
-
EXPERIMENTAL EVALUATION OF THE EMISSIVITY OF A NITI SHAPE MEMORY ALLOY
Publication -
Influence of Staphylloccoccus bacteria adhesion on the degradation of the Ti6Al4V alloy
PublicationThe paper deals with bacteria adhesion and the degradation of the Ti6Al4V alloy
-
Influence of the heat treatment on corrosion characteristics of the Superston alloy
PublicationW artykule przedstawiono wpływ hartowania i odpuszczania na twardość i właściwości korozyjne stopu Superston, stosowanego na śruby okrętowe. Stwierdzono, iż hartowanie z temperatury 900 st.C i odpuszczanie w temperaturze 550 st.C znacząco podwyższa odporność na korozję stopu Superston w 3% roztworze NaCl w porownaniu ze stanem odlanym.
-
Porous biomaterial for orthopaedic implants based on titanium alloy
PublicationTytan i jego stopy są szeroko stosowane jako biomateriały dla zastosowań ortopedycznych. Badania związane z ich najlepszą odpornością na korozję i ścieranie, biozgodnością i bioaktywnością są stale prowadzone. Obecne badania koncentrują się również na projektowaniu i produkcji materiałów porowatych w oparciu o stopy np. Ti-13Nb-13Zr, które mogą być stosowane do wytwarzania implantów. Jedną z najbardziej efektywnych metod wytwarzania...
-
Cavitation behavior of the SUPERSTON alloy after laser treatment
PublicationResults of laser treatment at cryogenic conditions and its influence on microstructure, microhardness and cavitation resistance of the SUPERSTON alloy are presented in this paper. Obtained results point at possibility of the increase hardness and cavitation resistance of the parts worked in cavitation conditions.
-
Surface treatment of porous Ti13Nb13Zr alloy for biomedical applications
PublicationPrzeprowadzono badania materiału porowatego, przeznaczonego na implanty ortopedyczne, wytworzonego metodą metalurgii proszków ze stopu Ti13Nb13Zr. Proszki z badanego stopu uzyskano metodą rozpylania plazmowego. Otrzymano próbki o otwartej porowatej strukturze, stopniu porowatości do 68% i średniej wielkości porów w przedziale 30-150 mikrometrów. Obróbka próbek porowatych - utlenianie termiczne, chemiczne i/lub elektrochemiczne...
-
High temperature corrosion resistance of porous hastelloy alloy
PublicationW pracy przedstawiono badania korozyjne stopu Hastelloy w wysokich temperaturach.
-
Underwater robot actuated by shape memory alloy wires
PublicationW pracy przedstawiono koncepcję projektu robota podwodnego z napędem wykorzystującym materiały SMA ze stopów z pamięcią kształtu. Rozpatrywany układ ma budowę modułową złożoną z segmentów na podobieństwo do anatomicznej budowy dżdżownicy. Pojedyńczy segment składa się z dwóch okrągłych tarcz, pomiędzy którymi umieszczono balon wypełniony wodą. Wielkość balonu jest dopasowana w taki sposób do rozmiarów tarcz oraz długości sprężyn...
-
Special Issue “Corrosion Resistance of Alloy and Coating Materials”
Publication -
High temperature corrosion resistance of porous hastelloy alloy
PublicationTo further understand the suitability of Ni-Cr-base alloy for solid oxide fuel cell (SOFC), a commercial Ni-Cr-Fe-Mo alloy, Hastelloy X was selected and evaluated for oxidation behaviour under high temperature conditions. HastelloyX was chosen due to its unusual resistance to oxidizing, reducing and neutral atmospheres. For long term stability of metal supported fuel cell, the corrosion resistance plays a vital role and must be...
-
Morphology and properties of nanotubular oxide layer on the Ti13Zr13Nb alloy
PublicationThe Ti13Zr13Nb alloy in solid and porous form was oxidised. The constant voltage 20 V, oxidation time 0.5 and 1 h, and 1 M H3PO4 (orthophosphoric acid) with addition of HF (hydrofluoric acid) as a test solution were applied. SEM (Scanning Electron Microscope) examinations of surface, EDS (Energy Dispersive X-ray Spectroscopy) chemical analysis, nanohardness and nano-scratch tests, and corrosion potentiokinetic tests at various...
-
THE PROPERTIES OF NANOSILVER – DOPED NANOHYDROXYAPATITE COATING ON THE Ti13Zr13Nb ALLOY
PublicationThe aim of this research was to study the properties of nanohydroxyapatite (nanoHAp) and nanohydroxyapatite, doped with nanosilver (nanoHAp/nanoAg), coatings obtained by an electrophoretic deposition process. The suspensions was prepared by dispersing 0.1 g of HAp nanopowder for nanoHAp coatings and 0.1 g of nanoHAp and 0.025 g nanoAg for nanoHAp/nanoAg coatings. The deposition was carried out for 1 min at 50 V voltage followed...
-
Microstructure and corrosion properties of the laser treated SUPERSTON alloy
PublicationPrzedstwiono wyniki laserowego nadtapiania powierzchni stopu SUPERSTON w warunkach kriogenicznych. Zaprezentowano obraz powierzchni stopu po badaniach korozyjnych oraz wyniki pomiarów mikrotwardości i odporności korozyjnej.
-
Stage of liver fibrosis in patients with congenital bleeding disorders and infected with hepatitis C virus
Publication -
Glucose metabolism disorders in patients with non-functioning adrenal adenomas — single-centre experience
PublicationIntroduction: The presence of glucose metabolism disorders and their possible correlation with degree of cortisol secretion were evaluated in patients with non-functioning adrenal incidentalomas (NFAIs). Material and methods: The study group consisted of 131 patients with hormonally inactive adrenal incidentalomas....
-
Analysis of occurrence of guided disorders in selected railway equipment — impact of load on measurement results
Publication -
Mutual Relationship Between Sleep Disorders, Quality of Life and Psychosocial Aspects in Patients With Psoriasis
Publication -
Pathogenesis of psoriasis in the “omic” era. Part III. Metabolic disorders, metabolomics, nutrigenomics in psoriasis
PublicationPsoriasis is a systemic disease that is strictly connected with metabolic disorders (insulin resistance, atherogenic dyslipidemia, arterial hypertension, and cardiovascular diseases). It occurs more often in patients with a more severe course of the disease. Obesity is specially an independent risk factor and it is associated with a worse treatment outcome because of the high inflammatory activity of visceral fatty tissue and...
-
Analysis of chemical composition and hardness of copper alloys = Badania składu chemicznego oraz twardości stopów miedzi
PublicationWykonano analizę składu chemicznego oraz badania twardości stopów miedzi zastosowanych na elementy łożyskowe. Sformułowano wnioski.
-
Structure and thermoelectric properties of Cs-Bi-Te alloys fabricated by different routes of reduction of oxide reagents
PublicationCesium-bismuth-telluride polycrystalline materials were fabricated using a cost-effective method based on a reduction of oxide reagents, leading to a production of a material with good thermoelectric properties. Several samples with various initial stoichiometry were prepared by melting of oxide powders at 1050 °C, quenching, milling to powders and then reducing in pure hydrogen at 400 °C. Another concept was to obtain the CsBi4Te6...
-
Understanding the origin of high corrosion inhibition efficiency of bee products towards aluminium alloys in alkaline environments
PublicationVarious bee products were found to be efficient corrosion inhibitors of aluminium in different environments. In particular, bee pollen was found to be highly effective in alkaline electrolytes, yet its highly complex composition and possible synergistic interactions hinder determination of the compounds acting as active corrosion inhibitors. The main purpose of the following work is to investigate the effect of solvents used for...
-
Evaluation of Surface Topography after Face Turning of CoCr Alloys Fabricated by Casting and Selective Laser Melting
Publication -
Multisine impedimetric monitoring with an in-depth distribution of relaxation times analysis of WE43 and AZ31 magnesium alloys corrosion
PublicationThis research aims to develop and utilize an impedance-based tool for monitoring non-stationary electrochemical processes, coupling the multisinusoidal perturbation signal approach and distribution of relaxation times (DRT) analysis for the first time. The approach was used to distinguish independent processes occurring at the surface of AZ31 and WE43 Mg alloys undergoing corrosion in Hank’s Balanced Salt Solution at 37 °C. We...
-
Optimization of Self-Organized TiO2 Nanotube Geometry on Ti and Ti Alloys Using Fuzzy Logic Reasoning
PublicationThe geometry of self-organized TiO2 nanotubes, obtained by electrochemicalanodization, has been determined by using fuzzy reasoning approach. The efficiency of TiO2nanotubular layer in biomedical applications depends on geometry and available surface area ofnanotubes, which can be determined by their diameter and length. The structure of nanotubesdepends on processing parameters of electrochemical anodization, like applied potential,anodization...
-
Psychometric assessment of the Internet Gaming Disorder diagnostic criteria: An Item Response Theory study
PublicationInternet Gaming Disorder (IGD) has been recognized by the American Psychiatric Association (APA) as a tentative disorder in the latest fifth revision of the Diagnostic and Statistical Manual of Mental Disorders (DSM-5). In order to advance research on IGD, the APA has suggested that further research on the nine IGD criteria to investigate its clinical and empirical feasibility is necessary. The aim of the present study was to develop...
-
Structural Disorder in High-Spin {CoII9WV6} (Core)-[Pyridine N-Oxides] (Shell) Architectures
Publication -
Nuclear magnetic relaxation and d-wave pairing in an extended Hubbard model with diagonal disorder
Publication -
Psychometric assessment of the Internet Gaming Disorder diagnostic criteria: An Item Response Theory study
PublicationInternet Gaming Disorder (IGD) has been recognized by the American Psychiatric Association (APA) as a tentative disorder in the latest fifth revision of the Diagnostic and Statistical Manual of Mental Disorders (DSM-5). In order to advance research on IGD, the APA has suggested that further research on the nine IGD criteria to investigate its clinical and empirical feasibility is necessary. The aim of the present study was to...
-
Geminate-pair dissociation yield in systems with exponential energetic disorder — A Monte Carlo study
PublicationGeminate electron–hole recombination in systems with exponential energetic disorder is studied by Monte Carlo method. The field and temperature dependencies of geminate-pair dissociation probability are calculated. It is established that the dissociation yield of carrier pairs depends mainly on the extent of carrier thermalization, which influences the Einstein relationship. The approximate limiting temperature is given by Te =...
-
Short-Term Effects of Intra-Articular Hyaluronic Acid Administration in Patients with Temporomandibular Joint Disorders
Publication -
Awareness of patients suffering from selected chronic diseases of the importance of physical activity in treating their disorders
Publication -
The Clinical Use of Platelet-Rich Plasma in Knee Disorders and Surgery—A Systematic Review and Meta-Analysis
Publication -
The Assessment of Risk and Predictors of Sleep Disorders in Patients with Psoriasis—A Questionnaire-Based Cross-Sectional Analysis
Publication -
The Level of FGF 21 as a New Risk Factor for the Occurrence of Cardiometabolic Disorders amongst the Psoriatic Patients
Publication -
PA32 aluminum alloy - tensile properties
Open Research DataIn addition to steel, aluminium alloys are the main building material used in the shipbuilding industry. Due to its undoubted advantages, such as low density (nearly three times lower than in the case of steel for shipbuilding) and high corrosion resistance, it is often used for hulls of yachts and small vessels as well as superstructures. For safety...
-
Torsional buckling and post-buckling of columns made of aluminium alloy
PublicationThe paper concerns torsional buckling and the initial post-buckling of axially compressed thin-walled aluminium alloy columns with bisymmetrical cross-section. It is assumed that the column material behaviour is described by the Ramberg–Osgood constitutive equation in non-linear elastic range. The stationary total energy principle is used to derive the governing non-linear differential equation. An approximate solution of the equation...
-
Electrochemical investigations of Al–Mg alloy subjected to tensile test
Publication -
Impedance analysis of Portevin-Le Chatelier effect on aluminium alloy
Publication