Search results for: REFORMER TUBES
-
Thermodynamic and geometrical characteristics of mixed convection heat transfer in the shell and coil tube heat exchanger with baffles
PublicationThe article presents passive heat transfer enhancement method in the form of baffles to increase the energy efficiency of the shell coil heat exchanger. Conducted literature review shows that, despite numer- ous studies, there is little work on the intensification of heat transfer at the shell side. Most of the work focuses on the impact of geometrical parameters of the coil itself. This article successfully proves that it is possible...
-
Experimental Research on Insufficient Water Lubrication of Marine Stern Tube Journal Bearing with Elastic Polymer Bush
PublicationWater-lubricated bearings with polymer bushes are steadily gaining popularity due to their advantages, including environmental friendliness, relatively simple construction and long-term operation. Nevertheless, in practice instances of damage to such bearings occur due to insufficient or absent flow of the lubricating agent. In this study, experimental tests established that elastic polymer bush bearing is capable of operating...
-
Experimental investigation on straight and u-bend double tube heat exchanger with active and passive enhancement methods
PublicationAuthors in this work want to demonstrate the possibility to increase the heat transfer efficiency by using simple wire coil inserts to create turbulent flow in the boundary layer as well as air blowing into the annulus of the pipe. In the study, Wilson plot approach was applied in order to estimate heat transfer coefficients for all heat exchanger (HX) configurations. The study focuses on experimental values of heat transfer coefficient...
-
Thermal and economic investigation of straight and U-bend double tube heat exchanger with coiled wire turbulator
PublicationExperimental research has been carried out for four individual heat exchanger constructions, i.e., plain double tube, turbulized double tube, plain U-bend and U-bend with turbulator. Tests were made for the water-water system. The study covered a wide measuring range, i.e., Re = 800–9000 – on the shell side, for a constant cold water temperature of 9 ◦C and hot water of 50 ◦C. The heat exchangers were made from copper tubes with...
-
Increase of the effective energy from the radiant tube equipped with regenerative system in comparison with conventional recuperative system
PublicationPrzedstawiono wyniki badań eksperymentalnych spalania HiTAC (High Temperature Air Combustion) z użyciem rury promieniującej w celu porównania systemu palników regeneracyjnych z konwencjonalnym systemem rekuperacyjnym.
-
Performance of the methanol PEM fuel cell module
PublicationPrzedstawiono charakterystyki układu zasilania składającego się z dwóch ogniw paliwowych o mocy 1.2 kW każde. Układ był zasilany metanolem, który podlegał procesowi reformowania w reformerze firmy Genesis Fueltech. Sprawność reformera wzrastała od 33% dla obciążenia minimalnego do 78% przy obciążeniu maksymalnym. Czystość uzyskiwanego wodoru była satysfakcjonująca w całym zakresie pracy reformera.
-
Nutritional Value of Jerusalem Artichoke Tubers (Helianthus tuberosus L.) Grown in Organic System under Lithuanian and Polish Conditions
Publication -
The Impact of Cultivation Management and Weed Control Systems of Very Early Potato on Weed Infestation, Biodiversity, and Health Safety of Tubers
Publication -
SOLUTIONS OF THE INTERMEDIATE SUPPORT STRUC- TURES OF THE NORTHERN MARMARA HIGHWAY (ISTAN- BUL’S RING ROAD) IN THE CONTEXT OF SEISMIC ACTIVITY
PublicationIn 2014–2018, as a result of the expansion of the city of Istanbul in Turkey, a project was imple- mented consisting of building a northern ring road, called the Northern Marmara Highway. The concept of the structural design of the ring road’s intermediate supports aims at constructing sup- ports that according to the TURKISH DLH 2008 standard must comply with the design require- ments for the three calculated earthquake insensitivity...
-
Efektywność skrępowania betonu w grubościennych słupach typu Concrete-Filled Steel Tube o przekroju kołowym
PublicationW słupach typu CFST w stanie granicznym dochodzi do zwiększenia wytrzymałości betonu rdzenia na skutek jego skrępowania. Zaistnienie tego zjawiska zależy od wielu czynników. Jednym z najważniejszych z nich jest sztywność obwodowa płaszcza stalowego. Jej wpływ na efektywność wzrostu wytrzymałości betonu rdzenia przebadano eksperymentalnie na grupie 48 grubościennych słupów CFST. Wykazano, że nadmierne zwiększanie grubości płaszcza...
-
Determination of the shape of the CFGFT cylindrical column based on laboratory tests
PublicationAnalyses were carried out on glass-fibre-reinforced polymer tube columns with reference to laboratory tests. The angles of the glass fibre beams were 20◦, 55◦ and 85◦. The study employed non-classical operational calculus. Various modulated harmonic signal shapes were considered for columns and tubes at buckling. The buckling loads were assessed and compared for different models.
-
Współpraca Unii europejskiej z Kazachstanem w zakresie dobrego rządzenia, demokracji, praw człowieka i wsparcia reform instytucjonalnych
Publicationartykuł ukazuje wsparcie UE dla Kazachstanu w zakresie przeprowadzania reform strukturalnych.
-
Study on effective front region thickness of PCM in thermal energy storage using a novel semi-theoretical model
PublicationThermal energy storage in mobile applications, particularly battery of electric vehicles, is currently gaining a lot of importance. In this paper, a semi-theoretical time-dependent mathematical model of the phase change in a double shell thermal energy storage module has been developed where the inner tube is a heat exchange surface. An effective front region thickness for the melting and solidification process has been studied....
-
AUGMENTATION OF THE CRITICAL HEAT FLUX IN WATER-Al2O3, WATER-TiO2 AND WATER-Cu NANOFLUIDS
PublicationThe main aim of the proposed study is therefore recognition of the phenomena accompanying nucleate boiling crisis of selected nanofluids during boiling on horizontal tubes of various outside diameters. Of particular interest is impact of contact angle and tube diameter on the value of critical heat flux. The results obtained should give more light on the nature of nucleate boiling crisis and will serve as a basis for future theoretical...
-
Application of Dispersive Liquid-Liquid Microextraction in Narrow-Bore Tube for Preconcentration and Spectrophotometric Determination of Cadmium in Aqueous Samples
Publication -
Fiberoptic intubation or video tube for trauma patient intubation—which method to choose? Randomized crossover manikin trial
Publication -
Experimental investigation of thermal energy storage in shell-and-multi-tube unit with nano-enhanced phase change material
PublicationThis paper deals with thermal energy storage with use of nanoparticle enhanced phase change material in shell-and-multitube unit. The experiments are conducted under atmospheric pressure. Paraffin wax and two different fatty acids are used as base phase change material. Graphite and multi-walled carbon nanotubes serve as nanoparticles. Graphite nanoparticles are tested at the concentrations of 0.1%, 1% and 5% by weight, while multi-walled...
-
Compatible Mixture of Bacterial Antagonists Developed to Protect Potato Tubers from Soft Rot Caused by Pectobacterium spp. and Dickeya spp.
Publication -
Ekonomiczne uwarunkowania funkcjonowania niepublicznych zakładów opieki zdrowotnej w warunkach reformy służby zdrowia na przykładzie województw z północno-wschodniej Polski.
Publication -
Polish tax reform "Polski Ład" – consequences of introducing changes on the example of selected flat-rate tax forms for micro and small companies
PublicationThis article describes aspects related to the introduction of the latest tax reform in Poland. The changes initiated in January 2022, under the name Polski Ład, concern a wide range of tax changes in Poland. Reform, in a broad sense, is a multidimensional government development program, which is primarily aimed at getting out of the crisis caused by the COVID-19 pandemic and a smooth transition to financing strategic goals in investment...
-
Multi-region fuzzy logic controller with local PID controllers for U-tube steam generator in nuclear power plant
PublicationIn the paper, analysis of multi-region fuzzy logic controller with local PID controllers for steam generator of pressurized water reactor (PWR) working in wide range of thermal power changes is presented. The U-tube steam generator has a nonlinear dynamics depending on thermal power transferred from coolant of the primary loop of the PWR plant. Control of water level in the steam generator conducted by a traditional PID controller...
-
Genetic and biochemical determinants of serum concentrations of monocyte chemoattractant protein-1, a potential neural tube defect risk factor
Publication -
Comparison of disk and tube methods for estimation of biostatic properties of polyurethanes based on synthetic poly[(R,S)-3-hydroxybutyrate
PublicationThe influence of novel aliphatic polyurethanes on growth of Staphyloccocus aureus (SA)in the around of polymer samples has been estimated by disk method. It was staed that the growth of SA was inhibited.The influence of polyurethanes on planctonic Staphyloccocus aureus was also pefrormed by tube method. In this test the slight decrease of bacteria concentration was noticed.
-
Heat transfer and pressure drop during flow boiling of pure efrigerants and refrigerant/oil mixtures in tube with porous coating
PublicationW pracy przedstawiono wpływ powłoki porowatej na średni współczynnik przejmowania ciepła oraz opory przepływu podczas wrzenia wybranych czynników chłodniczych wewnątrz poziomych rurek. Badania przeprowadzono dla techniczne czystych czynników chłodniczychR22, R134a i R407C oraz ich mieszanin z olejem poliestrowym 1% i 5% wrzących w rurkach wykonanych ze stali nierdzewnej, o wewnętrznej powierzchni gładkiej oraz z metaliczną powłoką...
-
ASSESSING THE POTENTIAL REPLACEMENT OF MINERAL OIL WITH ENVIRONMENTALLY ACCEPTABLE LUBRICANTS IN A STERN TUBE BEARING: AN EXPERIMENTAL ANALYSIS OF BEARING PERFORMANCE
PublicationT his study compares the performance of a plain bearing, with a similar structure to a tail shaft stern bearing, lubricated with either mineral oil or an environmentally acceptable lubricant (EAL). The main characteristic of the bearing is its length/diameter ratio of <1. Measurements are carried out with the bearing operating under loads from 0.5 to 1 MPa and seven speeds ranging from 1 to 11 rev/s. The bearing lubricated...
-
FLAME ATOMIC ABSORPTION SPECTROMETRIC DETERMINATION OF TRACE AMOUNTS OF SILVER IN RADIOLOGICAL WASTE SAMPLES AFTER SOLID PHASE EXTRACTION USING MULTI-WALLED CARBON NANO-TUBES MODIFIED BY SODIUM DODECYL SULFATE
Publication -
Molecular modelling of a psychrophilic β-galactosidase
PublicationAntarktyczny szczep, gram-ujemnych bakterii, wyizolowanych z przewodu pokarmowego kryla z gatunku Thyssanoessa macrura, sklasyfikowany na podstawie analizy sekwencji nukleotydowej geny 16S rDNA jako Pseudoalteromonas sp. 22b jest producentem wewnątrzkomórkowej zimnolubnej beta-galaktozydazy. Ponieważ enzym ten wykazuje wysoką aktywność katalityczną w zakresie temperatur od 0 do 30 stC, stanowi on atrakcyjny biokatalizator, użyteczny...
-
Study washboarding phenomenon in frame sawing machines
PublicationPraca dotyczy zjawiska washboarding cechującego się powstawaniem na piłowanej powierzchni sinusoidalnego profilu w przekroju poprzecznym i wzdłużnym. Wzór ten jest efektem drgań poprzecznych piły. Przedstawiono wyniki analiz teoretycznych oraz badań eksperymentalnych, w których wykazano, że zjawisko w przypadku pilarek ramowych jest efektem drgań wymuszonych brzeszczotu oraz regeneracji powstałej fali pierwotnej.
-
The effects of variable nitrogen fertilization on amino acid content in sweet potato tubers (Ipomoea batatas L. [Lam.]) cultivated in central and eastern Europe
Publication -
Identification and characterization of the Indian Yellow dyestuff and its degradation products in historical oil paint tube by liquid chromatography mass spectrometry
PublicationAn analytical protocol for identification of dyes using reversed phase liquid chromatography-mass spectrometry with atmospheric pressure electrospray ionization (LC-ESI/MS) is presented. The developed method has been successfully applied in identification of euxanthic acid and euxanthone, the main components of the Indian Yellow dye in a historical oil paint tube produced by Richard Ain`es, a recognizable French company supplying...
-
Experimental research on water lubricated marine stern tube bearings in conditions of improper lubrication and cooling causing rapid bush wear
PublicationWater lubricated bearings are popular in sliding bearings of marine propeller shafts, turbines and pump shafts. Such popularity is partly due to their simple construction which also means a relatively affordable price. In practical experience one may also observe cases of rapid wear or even malfunctions of this bearings, some of which may be caused by insufficient flow of lubricant leading to overheating. The conducted...
-
Assessment of cross compatibility of pear (Pyrus communis L.) cultivars on the basis of pollen tube observations and analysis of the S-RNase gene
Publication -
The effect of pressure on heat transfer during pool boiling of water-Al2O3 and water-Cu nanofluids on stainless steel smooth tube
PublicationPrzedstawiono wyniki badań eksperymentalnych wrzenia nanocieczy woda-Al2O3 i woda-Cu o koncentracjach nanocząstek 0.01%, 0.1% oraz 1% przy ciśnieniu absolutnym 10 kPa, 100 kPa oraz 200k Pa.
-
One-tube cell lysis and DNA extraction procedure for PCR based detection of Mycobacterium ulcerans in aquatic insects, molluscs and fish.
PublicationMycobacterium ulcerans jest bakterią wywołującą choroby skóry u ludzi i zwierząt. W trakcie prowadzonych badań opracowano prostą w wykonaniu metodę ekstrakcji DNA Mycobacterium ulcerans z próbek środowiskowych oraz klinicznych. Opracowana metoda izolacji DNA może być przydatna w badaniu źródeł infekcji oraz dróg szerzenia się Mycobacterium ulcerans.
-
Environmentally acceptable lubricants (EAL) compared with a reference mineral oil as marine stern tube bearing lubricant – Experimental and theoretical investigations
PublicationThe purpose of this research is to indicate the potential differences in bearing characteristics resulting from the application of different lubricant types with the same viscosity grade. The effect of different environmentally acceptable lubricants (EALs) on hydrodynamic journal bearing properties is studied experimentally and compared to the properties obtained after lubrication with a reference mineral oil. The results of the...
-
A new construction of shell-and-tube heat exchanger with impinging jets and minichannels technologies for heat recovery from gases – experimental analysis
PublicationA dynamic development of technologies allowing waste heat utilization is observed in a correspondence with a pro-ecological approach of the zero waste idea. Such approach becomes the most demanding in the area of low-temperature was heat sources, especially gaseous media. Till now, they were usually not utilized due to unfavorable thermal conditions and high costs. Therefore, the zero waste approach directs research on techniques...
-
Experimental and theoretical study of a vertical tube in shell storage unit with biodegradable PCM for low temperature thermal energy storage applications
PublicationThis article presents the experimental investigations of the coconut oil-based TES module for HVAC applications in the ambient and-sub ambient temperature range. To properly study this problem modular experimental module and test loop were developed. Special attention has been paid to study the physical mechanism of the melting/solidification process for natural substance (coconut oil) which has perspectives to be used in thermal...
-
Experimental and Computational Fluid Dynamics Studies on Straight and U-Bend Double Tube Heat Exchangers with Active and Passive Enhancement Methods
PublicationIn this work, the authors wanted to demonstrate the possibility to increase the heat transfer efficiency by using simple wire coil inserts to create turbulent flow in the boundary layer as well as air blowing into the annulus of the pipe. Experimental investigations were carried out for four heat exchanger constructions, i.e., plain double tube, turbulized double tube, plain U-bend double tube, U-tube with turbulator, plain double...
-
Tidskrift för genusvetenskap (former title : Kvinnovetenskaplig tidskrift)
Journals -
Renleixue Xuebao (former title: Acta Anthropologica Sinica)
Journals -
Composition and distribution of meiofauna, including nematode genera, in two contrasting Arctic beaches.
PublicationPraca dotyczy porównania zbiorowiska meiofauny, ze szczególnym uwzględnieniem nicieni, na dwóch różnych plażach Arktycznych. Badania prowadzono na Wyspie Niedzwiedziej należącej do archipelagu Svalbard.
-
Obliczenia numeryczne w analizach hydraulicznych istniejących systemów kanalizacji deszczowej i mieszanej z wykorzystaniem programu TFD (Tube Flow Drain)
PublicationProgramowanie inżynierskie jako nieodłączny element prac związanych z optymalizacją istniejących układów sieci kanalizacji deszczowej. Obliczenia numeryczne stosowane w programie TFD (Tube Flow Drain) znacznie przyspieszyły proces wykonywania obliczeń hydraulicznych w zamkniętych kanałach grawitacyjnych o przekroju kołowym. Możliwość wykonania szybko i niezawodnie, sprawdzenia wpływu zmiennych (np.. Kalkulacje w autorskim programie...
-
Concrete-filled FRP tubular members in marine and bridge structures
PublicationConcrete core of the concrete-filled tubes (CFTs) with circular cross-section is in the case of an axial compression subjected to a spatial state of compressive stresses. This state leads to enhancement in the concrete strength. The enhancement is utilized in Eurocode 4 design procedures for CFSTs (i.e. CFTs with tube made of steel). The structural design of CFFTs (i.e. CFTs with tube made of Fibre Reinforced Polymer - FRP) is...
-
Cuadernos de investigación histórica Brocar = Former title and ISSN
Journals -
Application of In-Syringe Dispersive Liquid–Liquid Microextraction and Narrow-Bore Tube Dispersive Liquid–Liquid Microextraction for the Determination of Trace Amounts of BTEX in Water Samples
Publication -
Understanding the early-stage release of volatile organic compounds from rapeseed oil during deep-frying of tubers by targeted and omics-inspired approaches using PTR-MS and gas chromatography
PublicationDuring deep-frying, a plethora of volatile products is emitted with the fumes. These compounds could act as oil quality indicators and change the indoor air composition leading to health risks for occupants. The presented experiments focus on deep-frying of different tubers in rapeseed oil at different frying temperatures. Here, two scenarios for real-time monitoring of volatile organic compounds (VOCs) using proton transfer reaction...
-
Inventory of the eastern wall of the presbytery of the former Dominican church - St. Mary's Church in Elbląg, stage from 2015.
Open Research DataThe drawing presents an inventory of the eastern wall of the presbytery of the former Dominican church - St. Mary's Church in Elbląg (now Art Gallery: Galeria EL), stage from 2015.The drawing also indicates the original, not overfolded during subsequent conservation and construction works, fragments of walls from 3 medieval stages of construction.
-
Analysis of transient heat transfer operation in tube wall.Selected papers from the International Conference on Turbines of Large Output devoted to 100th Anniversary of Prof. Robert Szewalski Birthday.
PublicationW pracy przedstawiono zachowanie się wymiennika ciepła stosowanego w układzie regeneracji turbin parowych w niestacjonarnych warunkach pracy.
-
Nineteenth Century Theatre and Film (former title :Nineteenth Century Theatre)
Journals -
Sociolinguistic Studies (former title: "Estudios Sociolinguistica" and ISSN (1576-7418)"
Journals