Filters
total: 1758
-
Catalog
displaying 1000 best results Help
Search results for: TURBINA WODNA
-
Analysis of the selection of low-temperature medium for a turbine power plant using ocean thermal energy (OTEC)
PublicationThe paper presents the results and conclusions of numerical calculations modelled in the EES program of a closed OTEC cycle. The following mediums were analysed: ammonia, R32, R41, R404a, R407c, R410a, R423a, R500, R502, R507a and R114, R152a, R234fa, R600, R1234yf, R1234ze. Analogous assumptions were adopted as in the ORC cycle with heat regeneration for dry refrigerants without regeneration for wet refrigerants. Each of them...
-
Investigations of the Working Process in a Dual-Fuel Low-Emission Combustion Chamber for an FPSO Gas Turbine Engine
PublicationThis investigation is devoted to an analysis of the working process in a dual-fuel low-emission combustion chamber for a floating vessel’s gas turbine. The low-emission gas turbine combustion chamber with partial pre-mixing of fuel and air inside the outer and inner radial-axial swirlers was chosen as the object of research. When modelling processes in a dual-flow low-emission gas turbine combustion chamber, a generalized method...
-
Design of Structure of Tension Leg Platform for 6 MW Offshore Wind Turbine Based On Fem Analysis
PublicationThe article presents the calculation and design stages of the TLP platform serving as a supporting construction of a 6 MW offshore wind turbine. This platform is designed to anchor at sea at a depth of 60 m. The authors presented the method of parameterization and optimization of the hull geometry. For the two selected geometry variants, the load and motion calculations of the platform subjected to wind, wave and current under...
-
Detection of Delamination in Laminate Wind Turbine Blades Using One-Dimensional Wavelet Analysis of Modal Responses
PublicationThis paper demonstrates the effectiveness of a nondestructive diagnostic technique used to determine the location and size of delamination in laminated coatings of wind turbine blades. This is realized based on results of numerical and experimental investigations obtained by the use of the finite element method (FEM) and laser scanning vibrometry (LSV). The proposed method is based on the one-dimensional continuous wavelet transform...
-
Application analysis of a hybrid solid oxide fuel cell-gas turbine system for marine power plants
PublicationThe results of theoretical studies of the possibilities of using hybrid solid oxide fuel cell–gas turbine (SOFC-GT) systems for marine power plants are presented. A 500 kW auxiliary marine power plant scheme using stacks of SOFCs in combination with a regenerative gas turbine operating with over-expansion based on our recent patent application is proposed. The results of mathematical modelling showed the opportunity to obtain a...
-
Heat turbomachinery
e-Learning Courses1. Steam turbine cycles. 2. Gas turbine cycles. 3. Combined gas-steam cycles. 4. Flows in nozzles. 5. Theory of turbine stages. 6. Multistage turbines. 7. Examples of turbine design.
-
Wojna i Pamięć. Czasopismo Muzeum II Wojny Światowej w Gdańsku
Journals -
Preliminary investigations on biological treatment of aqueous phase separated from cutting fluids
PublicationZaprezentowano wyniki fizykochemicznego podczyszczania przepracowanych cieczy obróbkowych pochodzących z różnych źródeł. Emulsje przepracowanych cieczy obróbkowych zostały rozdzielone na fazę organiczną i wodną z wykorzystaniem różnych koagulantów. Wydzielona faza wodna została następnie poddana biologicznemu oczyszczaniu z wykorzystaniem osadu czynnego. W wyniku oczyszczania ścieków uzyskano 59-88% obniżenie wartości ChZT.
-
Turbiny Parowe, Gazowe i Wodne
e-Learning Courses -
Turbiny Parowe, Gazowe i Wodne
e-Learning CoursesPodstawy obiegów cieplnych turbin parowych (obieg Rankine'a, obiegi z regeneracją, obiegi z przegrzewem międzystopniowym, dobór parametrów i schematów obiegu). Podstawy obiegów cieplnych turbin gazowych (obieg Braytona, obiegi z regeneracją, chłodzeniem międzystopniowym, sekwencyjnymi komorami spalania, Ericssona, dobór parametrów projektowych). Teoria stopnia turbinowego (rozkład ciśnień na profilu, siły działające na profil,...
-
Turning process monitoring of internal combustion engine piston’s cylindrical surface
Publication -
A CUSUM-Based Approach for Condition Monitoring and Fault Diagnosis of Wind Turbines
Publication -
Eulerian motion magnification applied to structural health monitoring of wind turbines
PublicationSeveral types of defects may occur in wind turbines, as physical damage of blades or gearbox malfunction. A wind farm monitoring and damage prediction system is built to observe abnormal vibrations of elements of wind turbine: blades, nacelle, and tower. Contactless methods are developed which do not require turbine stopping. In this work, structural health monitoring of a wind turbine is evaluated using a conversion from the captured...
-
Influence of ducting geometry on working parameters of pipe type hydraulic turbines
PublicationMała energetyka wodna. Omówiono własności użytkowe - głównie, sprawność i adaptacyjność - uzyskiwane poprzez rozwiązania układów turbinowych stosowanych w obszarze zagospodarowywania piętrzeń niskospadowych. Wskazano przyczyny od których te własności zależą. Pokazano też przykład rozwiązania o pożądanych własnościach dla zagospodarowywania obiektów w mało atrakcyjnym ekonomicznie obszarze piętrzeń najniższych.
-
Wind Turbines Modeling as the Tool for Developing Algorithms of Processing their Video Recordings
PublicationIn the real world, many factors exist disturbing observation of the examined phenomena and causing various noises and distortions in recorded signals. It very often makes it difficult or even impossible to optimize various signal processing algorithms, through finding appropriate parameters. In this paper, we show an application, that retrieves wind turbine rotor speed from recorded video. Next, we describe the process of reduction...
-
Remote Health Monitoring of Wind Turbines Employing Vibroacoustic Transducers and Autoencoders
PublicationImplementation of remote monitoring technology for real wind turbine structures designed to detect potential sources of failure is described. An innovative multi-axis contactless acoustic sensor measuring acoustic intensity as well as previously known accelerometers were used for this purpose. Signal processing methods were proposed, including feature extraction and data analysis. Two strategies were examined: Mel Frequency Cepstral...
-
Wind Turbines Modeling as the Tool for Developing Algorithms of Processing their Video Recordings
PublicationIn the real world, many factors exist disturbing observation of the examined phenomena and causing various noises and distortions in recorded signals. It very often makes it difficult or even impossible to optimize various signal processing algorithms, through finding appropriate parameters. In this paper, we show an application, that retrieves wind turbine rotor speed from recorded video. Next, we describe the process of reduction...
-
(Vapour + liquid) equilibrium in (n,n-dimethylacetamide + ethanol + water) at the temperature 313.15 K
PublicationW pracy prezentowane są pomiary całkowitej prężności pary dla tytułowego układu trójskładnikowego oraz dla składowych układów binarnych. Uzyskane w pracy wyniki porównane zostały z wcześniejszymi danymi dla podobnych układów. Znaleziono w przybliżeniu liniową zależność pomiędzy wartościami nadmiarowej entalpii swobodnej Gibbsa a objętością molową amidu, spełnianą w układach dwuskładnikowych: amid + alkohol alifatyczny.
-
Badanie dynamiki platform pływających morskich turbin wiatrowych z zastosowaniem metod numerycznej mechaniki płynów
PublicationPraca dotyczy badania ruchu platform pływających pod morskie turbiny wiatrowe. Przedstawiono w niej główne metody obliczeń i przedyskutowano ich zastosowanie. Na przykładzie koncepcji konstrukcji 3-kolumnowej platformy typu Spar przedstawiono metodykę wykonywania obliczeń z zastosowaniem programu AQWA opartego na metodzie dyfrakcyjnej, rozszerzonego o współczynniki wynikające z lepkości wyznaczone za pomocą obliczeń RANSE-CFD....
-
Application of neural networks for identification of forcedness having effect on magnitude of turbine rotor vibration using rotor trajectory.
PublicationW pracy dokonano analizy zastosowania sieci neuronowych do wyznaczenia wartości wymuszeń wpływających na wielkość drgań wirnika używając trajektorii jako parametr określający drgania. Badania przeprowadzono na powietrznej, jednostopniowej turbinie modelowej. Przemieszczenia poziome i pionowe wirnika turbiny mierzono przy pomocy systemu pomiarowego i rejestrowano na oscyloskopie cyfrowym. Przeprowadzono pomiary trajektorii ruchu...
-
Ocena wpływu temperatury powietrza atmosferycznego na efekty pracy zespołu turbiny gazowej w sezonie letnim.
PublicationPrzeprowadzono analizę wpływu zmiany temperatury powietrza atmosferycznego na pracę zespołu turbiny gazowej, tzn. na zmianę mocy sprężarki oraz wzrost zużycia paliwa gazowego.
-
Wolnoobrotowy generator z magnesami trwałymi do elektrowni wiatrowej z turbiną o pionowej osi obrotu
PublicationW artykule przedstawiono założenia projektowe, wybrane wyniki etapu projektowania i badania prototypu wolnoobrotowego generatora z magnesami trwałymi współpracującego z elektrownią wiatrową z innowacyjną turbiną o pionowej osi obrotu. Projekt został wykonany na zlecenie firmy ALU ECO Sp. z o.o. z Gdańska w ramach projektu badawczorozwojowego Pionowa Turbina Wiatrowa, współfinansowanego przez Polską Agencję Rozwoju Przedsiębiorczości...
-
Analysis of the possibility of increasing thermal-electric energy conversion ratio in CHP units based on micro gas turbine
PublicationThe aim of this paper is to analyze the possibility of increasing thermal energy to electricity conversion efficiency in combined heat and power (CHP) units based on micro gas turbine during low heat demand periods. At the beginning sustainable development postulates under power engineering are explained. Next micro CHP as part of distributed generation idea is presented. The main part of the article is based on results of thermodynamic...
-
Wykorzystanie sieci nieuronowych do przyspieszenia przepływowych obliczeń numerycznych - wybór geometrii wieńca kierowniczego turbiny parowej
PublicationReferat stanowi wprowadzenie do dalszych prac nad rozprawą doktorską. W referacie przedstawiono problem wyboru geometrii wieńca kierowniczego turbiny parowej do dalszych obliczeń. Pokazano kryteria według których dokonywano wyboru spośród różnych typów geometrii.Krótko scharakteryzowano poszczególne typy wieńców turbinowych: wieńce z łopatkami typu PLK,wieńce z łopatkami typu PKH, stopnie reakcyjne oraz ostatnie stopnie części...
-
Exhaust gas temperature measurements in diagnostic examination of naval gas turbine engines. Part II. Unsteady processes
PublicationThe second part of the article presents the results of operating diagnostic tests of a two- and three-shaft engine with a separate power turbine during the start-up and acceleration of the rotor units. Attention was paid to key importance of the correctness of operation of the automatic engine load control system, the input for which, among other signals, is the rate of increase of the exhaust gas flow temperature. The article...
-
Elektrownia morska kombinowana z silnikiem Diesla i układem turbiny parowej wykorzystującej energię spalin wylotowych
PublicationW opracowaniu przedstawiono koncepcję elektrowni morskiej kombinowanej z silnikiem Diesla oraz układem turbiny gazowej i parowej wykorzystującej energię spalin wylotowych. Zaproponowano warianty układów kombinowanych składających się z wolnoobrotowego silnika Diesla jako napędu głównego elektrowni oraz turbiny parowej wykorzystującej ciepło zawarte w spalinach wylotowych.
-
Techno-economic evaluation of combined cycle gas turbine and a diabatic compressed air energy storage integration concept
PublicationMore and more operational flexibility is required from conventional power plants due to the increasing share of weather-dependent renewable energy sources (RES) generation in the power system. One way to increase power plant’s flexibility is integrating it with energy storage. The energy storage facility can be used to minimize ramping or shutdowns and therefore should lower overall generating costs and CO2 emissions. In this article,...
-
Investigation of ecological parameters of a gas turbine combustion chamber with steam injection for the floating production, storage, and offloading vessel
PublicationThe article is dedicated to the investigation of the possibility of using the contact type gas turbine cycle with steam injection into the combustion chamber for the floating production, storage, and offloading vessel in order to increase the specific power and efficiency and reduce emissions of toxic components. A new approach is proposed, associated with the use of the two-stage injection of superheated steam into a gas turbine...
-
INVESTIGATIONS OF THE EMISSION CHARACTERISTICS OF A DUAL-FUEL GAS TURBINE COMBUSTION CHAMBER OPERATING SIMULTANEOUSLY ON LIQUID AND GASEOUS FUELS
PublicationT his study is dedicated to investigations of the working process in a dual-fuel low-emission combustion chamber for a floating vessel’s gas turbine. As the object of the research, a low-emission gas turbine combustion chamber with partial premixing of fuel and air inside the outer and inner radial-axial swirls was chosen. The method of the research is based on the numerical solution of the system of differential...
-
Different design aspects of an Organic Rankine Cycle turbine for electricity production using a geothermal binary power plant
PublicationIn recent years, pressure has been growing to increase the share of renewable energy sources in electricity generation, which may offer opportunities for the development of geothermal energy in regions that have been so far considered unprofitable in this respect. One such country currently undergoing an energy transition is Poland in which low-temperature geothermal resources are currently used for district heating and recreation...
-
Stability Analysis of the Floating Offshore Wind Turbine Support Structure of Cell Spar Type During its Installation
PublicationThe article presents the results of selected works related to the wider subject of the research conducted at the Faculty of Ocean Engineering and Ship Technology of the Gdansk University of Technology, which concerns design and technology of construction, towing, and settlement on the seabed, or anchoring, of supporting structures for offshore wind farms. As a result of this research, several designs of this type of objects were...
-
Design of Jack-up Platform for 6 MW Wind Turbine: Parametric Analysis Based Dimensioning of Platform Legs
PublicationThe article presents the results of the research conducted within the framework of the project entitled WIND-TU-PLA (ERA-NET, MARTEC II), the general aim of which was to design and analyse supporting structures for wind turbines intended for operation on the South Baltic area. The research part described in the article aimed at developing a preliminary design for a jack-up platform which can operate on water areas with depth of...
-
BADANIA MATERIAŁOWE USZKODZONEJ RURY COIL TUBING RISERA Z1
PublicationW ramach ekspertyzy wykonano analizę materiałową i określono przyczyny uszkodzenia rury risera wody zatłaczającej.
-
SHORT REVIEW AND 3-D FEM ANALYSIS OF BASIC TYPES OF FOUNDATION FOR OFFSHORE WIND TURBINES
PublicationSome problems of the foundations of offshore wind turbines are considered in this paper. A short review is presented on the two basic types of foundations, i.e. monopiles and gravity foundations, including their basic features and applications as well as general design considerations. Also, some issues regarding analysis are discussed, including geotechnical problems and modelling techniques. A numerical model of offshores turbine...
-
Experimental Investigation of Prototype Water-Lubricated Compliant Foil Bearings
PublicationPraca zawiera wyniki badań doświadczalnych prototypowego łożyska foliowego smarowanego wodą. Łożyska tego typu mogą mieć zastosowanie w węzłach, od których wymaga się ekologicznego środka smarowego, np. pompy wodne czy turbiny wodne. W opracowaniu zademonstrowano wyniki badań trzech prototypowych poprzecznych łożysk foliowych. Opisano napotkane problemy badań oraz wprowadzonych do konstrukcji łożyska zmian, których celem była poprawa...
-
Effect of crystalline emulsifier composition on structural transformations of water-in-oil emulsions: Emulsification and quiescent conditions
Publication -
Metoda neuronowego wyznaczania przestrzennych pól przepływów w przydźwiękowych i naddźwiękowych kanałach łopatkowych turbin parowych
PublicationNiniejsza rozprawa doktorska została poświęcona opracowaniu metody neuronowego wyznaczania przestrzennych pól przepływów w okołodźwiękowych kanałach łopatkowych turbin parowych. Obiektem badań naukowych przedstawionych w kolejnych rozdziałach są dwa ostatnie stopnie części niskoprężnej turbozespołu 18K370 z wylotem ND-37. Pierwszym etapem badań była budowa numerycznego modelu przepływu pary mokrej przez analizowany układ łopatkowy....
-
Thermodynamic Cycle Concepts for High-Efficiency Power Plants. Part B: Prosumer and Distributed Power Industry
PublicationAn analysis was carried out for different thermodynamic cycles of power plants with air turbines. A new modification of a gas turbine cycle with the combustion chamber at the turbine outlet has been described in the paper. A special air by-pass system of the combustor was applied, and in this way, the efficiency of the turbine cycle was increased by a few points. The proposed cycle equipped with an effective heat exchanger could...
-
Intelligent Optimization of Hard-Turning Parameters Using Evolutionary Algorithms for Smart Manufacturing
Publication -
Study on physical and technological effects of precise turning with self-propelled rotary tool
Publication -
Surface quality and topographic inspection of variable compliance part after precise turning
Publication -
Turning maneuver as a potential cause of the next stability failure mode for a ship in operation
PublicationThe only formal stability-related requirement referring to a turning maneuver of a ship results from the IS Codeand its application is limited to passenger ships only. The goal of the adopted criterion is to prevent an excessiveangle of heel in turn. Likewise, the remaining prescriptive criteria, this one is simply based on the concept ofa threshold that must not be exceeded. In this case, the angle of heel...
-
MODELLING OF THE VISCOSITY EFFECT OF HEAVE PLATES FOR FLOATING WIND TURBINES BY HYDRODYNAMIC COEFFICIENTS
PublicationOne of the methods of modelling the movement of floating wind turbines is the use of the diffraction method. However, this method does not take into account the influence of viscosity; therefore, in many cases, it needs to be extended with a matrix of appropriate coefficients. The effect of viscosity causes both the added mass coefficient and the damping coefficient to increase. The determined coefficients were entered into the...
-
On Wilcoxon rank sum test for condition monitoring and fault detection of wind turbines
Publication -
Effective method for determining environmental loads on supporting structures for offshore wind turbines
PublicationThis paper presents a description of an effective method for determining loads due to waves, current and wind acting on the supporting structures of the offshore wind turbines. This method is dedicated to the structures consisting of the cylindrical or conical elements as well as (truncates) pyramids of polygon with a large number of sides (8 or more). The presented computational method is based on the Morison equation, which was...
-
Design analysis of ORC micro-turbines making use of thermal energy of oceans
PublicationThe article presents the results of the analysis of energy conversion cycles making use of thermal energy of oceans. The objects of analysis were two cases of closed Organic Rankine Cycle (ORC) power plants, which were: the cycle in which the vapour of the working medium was produced by warm oceanic water in the circum-equatorial zone, and the so-called “arctic” cycle in which this vapour was produced by non-frozen water in the circumpolar...
-
Operating and economical conditions of cooling water control for marine steam turbines condensers
PublicationW pracy dokonano analizy ekonomicznej i eksploatacyjnej sterowania pracą pomp wody chłodzącej skraplacze turbin okrętowych. Wzięto pod uwagę cechy konstrukcyjne pomp wody chłodzącej skraplacze główne i najnowsze wyniki badań dla takich pomp w zastosowaniach lądowych. Uwagę skupiono przede wszystkim na turbinowych parowych siłowniach okrętowych.
-
Ecological bearing systems for water turbines – research and development at Gdansk University of Technology
PublicationIncreasing requirements for environmental protection make it necessary to introduce new materials and designs. Hydroelectric power plants operating in direct contact with water reservoirs and rivers are potentially endangering water cleanliness, hence they should also be modernized in the way minimizing the environmental hazards. A lot of progress in this field has been achieved in last decades, but still there is much work to...
-
Effective method for determining environmental loads on supporting structures for offshore wind turbines
PublicationThis paper presents a description of an effective method for determining loads due to waves and current acting on the supporting structures of the offshore wind turbines. This method is dedicated to the structures consisting of the cylindrical or conical elements as well as (truncates) pyramids of polygon with a large number of sides (8 or more). The presented computational method is based on the Morison equation, which was originally...
-
Analysis of the Hydrodynamic Properties of the 3-Column Spar Platform for Offshore Wind Turbines
PublicationThe article presents a design of a floating platform for offshore wind turbines. The concept is a modification of the Spar design and consists of three variable section columns connected to each other by a ballast tank in the lower part of the platform. This solution makes it possible to influence the position of the centre of buoyancy and the centre of mass of the structure. Compared to the classic Spar platform structure, the...