Filtry
wszystkich: 237
wybranych: 149
Wyniki wyszukiwania dla: HOT-ROLLED SCHET
-
Influence of compaction effectiveness on interlayer bonding of asphalt layers
PublikacjaThe paper presents the results of research on the interlayer bonding of asphalt layers compacted in the laboratory and in the field. To measure the interlayer bonding at a temperature of 20°C the Leutner test apparatus was used and load was applied at a rate of 50 mm/minute. Three types of interlayer interfaces were tested: no tack coat and tack coats made of two types of the pure bitumen emulsions. Four compaction techniques were...
-
PROBLEMS OF THE STARTING AND OPERATING OF HYDRAULIC COMPONENTS AND SYSTEMS IN LOW AMBIENT TEMPERATURE (PART V) METHODS ENSURING CORRECT START-UP OF HYDRAULIC COMPONENTS OF SHIP’S ONBOARD DEVICES IN LOW AMBIENT TEMPERATURES
PublikacjaA large number of hydraulic devices and systems are started in low ambient temperatures. A good example of such a device is the hoisting winch on the ship. Starting hydraulic drive units in thermal shock conditions (rapid supply of hot oil to the cold unit) may lead to incorrect operation of the actuating system, for instance, due to the loss of clearance between cooperating elements. The article presents methods to prevent the...
-
PRĄDY WYRÓWNAWCZE W UZIOMACH FUNDAMENTOWYCH I SZTUCZNYCH
PublikacjaW artykule omówiono zasady wykonywania uziomów fundamentowych i sztucznych. Przedstawiono wyniki pomiarów prądów w instalacji zawierającej stal zbrojeniową w fundamencie, połączoną z układem uziomu sztucznego w ziemi wykonanym z stali ocynkowanej.
-
The new concept of product. Cooling band
PublikacjaThe chapter below presents the innovative solution consist in applying the cooling band to help holding the hot object. The solution was found through substitute inputs analysis and brain storm method. The new product was submitted in Polish Patent Office under the No. W.120905.
-
On the production of electricity in Poland using a geothermal binary power plant - A thermodynamic overview - Part I
PublikacjaPoland has a significant potential of geothermal energy. However, the high-temperature sources that are needed to drive power plants are found in relatively few places. Therefore, the objective of this paper is to consider any location in the northern part of Poland as a possible place to build a binary power plant. A scientific research was confirmed the existence of an elevated temperature gradient in this region. The hot rocks...
-
Efficient method for octahedral NH2-MIL-125 (Ti) synthesis: Fast and mild conditions
PublikacjaA new hot injection method for preparing octahedral NH2-MIL-125 (Ti) was developed. This method is six times faster and conducted under milder conditions, i.e., at 120°C in a flask, and exhibits higher crystal formation efficiency than the commonly used solvothermal method while maintaining comparable structural, optical, and photocatalytic properties.
-
Analytical method for calculation of heat source temperature drop for the Organic Rankine Cycle application
PublikacjaIn the paper presented are considerations on the cooperation of the limited capacity heat source with the Organic Rankine Cycle unit. Usually the heat source providing thermal energy to the Organic Rankine Cycle (ORC) may have twofold characteristics. It can be in the form of a single phase fluid, i.e. as hot exhaust gas or hot liquid, or in some cases it may be available as a phase changing fluid, as for example, technological...
-
Advantages of the Application of the Temper Bead Welding Technique During Wet Welding
PublikacjaThermo-mechanically rolled S460ML steel was chosen for welding in underwater wet welding conditions by covered electrodes. The main aim of this study was to check the weldability for fillet welds in a water environment by controlled thermal severity (CTS) tests and to check the influence of temper bead welding (TBW) on the weldability of the investigated steel. Non-destructive and destructive tests showed that S460ML steel has...
-
Comparison of traditional district heating with low temperature district heating systems featuring organic Rankine cycle and heat pump
PublikacjaPaper presents a comparison between a traditional district heating system with conventional boilers as a source of heat and electricity purchases from power utilities and a low temperature DH system incorporating the CHP with organic Rankine Cycle providing electricity and local heat pump raising the temperature of the DH fluid to the required temperature in the dwelling, meaning that both heat and electricity are produced within...
-
Unprecedented Adhesive Performance of Propylene-Based Hydroxyl Functionalized Terpolymers
PublikacjaThe synthesis of hydroxyl functionalized propylene-based terpolymers and their performance as hot melt adhesives were investigated. The products comprise uniformly distributed butyl and 4-hydroxyl-butyl branches along the polypropylene backbone. Despite the low hydroxyl-functionality level of ≤ 0.5 mol%, hydroxyl functionalized terpolymers show formidable adhesion to aluminum and steel providing an adhesive strength exceeding 16...
-
An investigation of selected monoaromatic hydrocarbons released from the surface of polystyrene lids used in coffee-to-go cups
PublikacjaA consumer trend towards the fast preparation of beverages has increased the popularity of hot beverages (especially coffee and tea) available in disposable containers called coffee-to-go cups with fitted polystyrene lids. Lids in contact with hot beverages may release low molecular weight organic compounds into the gaseous phase causing direct exposure of consumers to these compounds during drinking. The paper describes in detail...
-
Nanotechnologies in Development of Structural Materials and Biomaterials
PublikacjaThe nanometric materials and technologies resulted in nanostructures are reviewed. The examples of nanomaterials are shown. The typical nanotechnologies, including plastic deformation, mechanical attrition, controlled detonation, hot plasma jet synthesis, laser vaporisation, CVD and PVD, mechanical milling, annealing, ultrasonic irradiation, nanolithography, electrocrystallisation, electrospinning, sol-gel method, cryogenic laser-enhanced...
-
Smart city and fire detection using thermal imaging
PublikacjaIn this paper, we summarize the results obtained from fire experiments. The aim of the work was to develop new methods of fire detection using IR thermal imaging cameras and dedicated image processing. We conducted 4 experiments in different configurations and with the use of different objects. The conducted experiments have shown the great usefulness of infrared cameras for detecting the seeds of a fire. Even cheap low-resolution...
-
Storing thermal energy from solar collectors for the needs of a detached house
PublikacjaThis work evaluates the possibility of meeting a single familu household's need for hot water and heat year round, using solar collectors as the sole energy sourse. The main flaw of energetic systems based on solar energy is that the energy supply is usually insufficient in winter, when it is most needed. This work is going to show thatm for a house surface of 150 m2 and base dimension of 10x10m, it is possible to supply sufficient...
-
A LABORATORY STAND FOR THE ANALYSIS OF DYNAMIC PROPERTIES OF THERMOCOUPLES
PublikacjaIn the present elaboration, problems connected with measurements of high variable temperatures of gases are introduced and the impact of dynamic properties of different construction solutions of thermoelements on the accuracy of the measurements is considered. A laboratory stand built within research under doctoral thesis, destined for analysis of dynamic properties of thermocouples is also described. Results of numerical simulation...
-
Management of low-temperature heat source by ORC aided by additional heat source
PublikacjaThe presented work is aimed at utilisation of waste heat in the manner to produce electricity in ORC installation. Therefore the precondition of the study was to use the waste heat available in the form of a stream of hot water at 90°C. Such low enthalpy heat source is rather insufficient to produce a good quality vapour to feed the ORC turbine. That was the incentive to search for the ways of increasing the temperature of the...
-
Landscape of the Vistula Estuary - searching for traces of ingenium embodied
PublikacjaArtykuł podaje skrótowe informacje o dawnym i współczesnym znaczeniu obiektów inżynieryjnych w krajobrazie delty Wisły, które znalazły się na trasie objazdu konserwatorskiego w dniu 5 maja w ramach realizacji programu konferencji HOT-GO 4 wraz z kalendarium ich dziejów: Most Lisewski przez Wisłę w Tczewie, wielki przekop Wisły w Świbnie, śluzy w Przegalinie, Gdańskiej Głowie i Białej Górze, relikty kanału w Piekle.
-
The Influence of Drying Temperature on Color Change of Hornbeam and Maple Wood Used as Surface and Inner Layers of Wood Composites
PublikacjaThe thermal treatment of wood changes its structure due to the degradation of wood polymers (cellulose, hemicellulose and lignin), so the physical properties of wood are either improved or degraded. Color changes apply not only to natural wood, but also to such wood composites for which some amount of glue is used in their construction (e.g., plywood, blockboard or laminboard). This article is focused on the analysis of hornbeam...
-
Rational Use of Primary Energy in Single-Family Residential Houses
PublikacjaThis work presents results of the primary energy use for heating residential single-family house. Analysis includes domestic hot water system (DHW) and heating, ventilation and air condition system (HVAC). During researches the conventional and alternative energy sources (natural gas, biomass, fuel oil, bituminous coal, lignite or electric energy obtained from electric power system – EPS) were used in DHW and HVAC systems. Furthermore...
-
Problemy z powłokami antykorozyjnymi na elementach wyposażenia obiektów mostowych
PublikacjaPrzedstawiono problem wadliwości zabezpieczenia antykorozyjnego w zakresie malarskich powłok ochronno - dekoracyjnych wykonywanych na stalowych elementach barier zabezpieczonych uprzednio poprzez ocynkowanie metodą zanurzeniową. Wykorzystując przykłady pochodzące z różnych obiektów przedstawiono powtarzający się problem delaminacji powłok malarskich, niezależny od rodzaju zastosowanych wyrobów lakierniczych oraz znacznego rozwoju...
-
Problemy z powłokami antykorozyjnymi na elementach wyposażenia obiektów mostowych
PublikacjaOpisano problem wadliwości zabezpieczenia antykorozyjnego w zakresie malarskich powłok ochronno-dekoracyjnych wykonywanych na stalowych elementach barier zabezpieczonych uprzednio poprzez ocynkowanie metodą zanurzeniową na gorąco. Wykorzystując przykłady pochodzące z różnych obiektów przedstawiono powtarzający się problem delaminacji powłok malarskich, niezależny od rodzaju zastosowanych wyrobów lakierniczych oraz znacznego rozwoju...
-
AUTONOMOUS PLATFORM TO PROTECT MARITIME INFRASTRUCTURE FACILITIES
PublikacjaProblems regarding the security of maritime infrastructure, especially harbours and offshore infrastructure, are currently a very hot topic. Due to these problems, there are some research projects in which the main goal is to decrease the gap and improve the methods of observation in the chosen area, for both in-air and underwater areas. The main goal of the paper is to show a new complex system for improving the security of the...
-
Characterization of Bi6Fe2Ti3O18 Ceramics with Impedance Spectroscopy
PublikacjaIn the present research the tool of impedance spectroscopy was utilized to characterize dielectric behavior of Aurivillius-type ceramics of Bi6Fe2Ti3O18 composition fabricated by hot pressing method from the stoichiometric mixture of oxides Bi2O3, TiO2 and Fe2O3. Impedance spectroscopy was applied to characterize dielectric response of bulk, grain boundary, and material/electrode interfaces of the fabricated polycrystalline ceramic...
-
Fatigue strength determination of ship structural joints. Part I - Analytical methods for determining fatigue strength of ship tructures
PublikacjaSpectacular accidents at sea which have happened for a few last years show that hull structures of contemporary sea-going ships are not perfect and must be systematically improved. Fatigue strength is one of the groups of strength problems which affect design of contemporary ship's structures and greatly contribute in their improvement process. In this paper several approaches to estimation of fatigue life of hull structural...
-
Analysis of the Heating Process of Hydraulic Motors during Start-Up in Thermal Shock Conditions
PublikacjaConditions that prevail during harsh winters and hot summers pose a serious challenge for machine designers building devices suitable for operation in extreme weather. It is essential for the designers and the users to define the principles and conditions for the safe operation of machines and devices with hydraulic drive in low ambient temperatures. Bearing in mind the above, the author tested the hydraulic motors in thermal shock...
-
The Effect of AgInS2, SnS, CuS2, Bi2S3 Quantum Dots on the Surface Properties and Photocatalytic Activity of QDs-Sensitized TiO2 Composite
PublikacjaThe eect of type (AgInS2, SnS, CuS2, Bi2S3) and amount (5, 10, 15 wt%) of quantum dots (QDs) on the surface properties and photocatalytic activity of QDs-sensitized TiO2 composite, was investigated. AgInS2, SnS, CuS2, Bi2S3 QDs were obtained by hot-injection, sonochemical, microwave, and hot-injection method, respectively. To characterize of as-prepared samples high-resolution transmission electron microscopy (HRTEM), scanning...
-
Increase of power and efficiency of the 900 MW supercritical power plant through incorporation of the ORC
PublikacjaThe objective of the paper is to analyse thermodynamical and operational parameters of the supercritical power plant with reference conditions as well as following the introduction of the hybrid system incorporating ORC. In ORC the upper heat source is a stream of hot water from the system of heat recovery having temperature of 90 °C, which is additionally aided by heat from the bleeds of the steam turbine. Thermodynamical analysis...
-
Heat transfer in plate heat exchanger channels: experimental validation of selected correlation equations
PublikacjaThis study is focused on experimental investigation of selected type of brazed plate heat exchanger. The Wilson approach was applied in order to estimate heat transfer coefficients for the PHEx passages. The main aim of the paper was to experimentally check ability of several correlations published in the literature to predict heat transfer coefficients by comparison experimentally obtained data with appropriate predictions. The...
-
Analysis of the possibility of increasing thermal-electric energy conversion ratio in CHP units based on micro gas turbine
PublikacjaThe aim of this paper is to analyze the possibility of increasing thermal energy to electricity conversion efficiency in combined heat and power (CHP) units based on micro gas turbine during low heat demand periods. At the beginning sustainable development postulates under power engineering are explained. Next micro CHP as part of distributed generation idea is presented. The main part of the article is based on results of thermodynamic...
-
Heat transfer in plate heat exchanger channels: experimental validation of selected correlation equations
PublikacjaThis study is focused on experimental investigation of selected type of brazed plate heat exchanger. The Wilson approach was applied in order to estimate heat transfer coefficients for the PHEx passages. The main aim of the paper was to experimentally check ability of several correlations published in the literature to predict heat transfer coefficients by comparison experimentally obtained data with appropriate predictions. The...
-
GROUPS OF GERMAN DOMESTIC APPLIANCE MANUFACTURERS ACCORDING TO NEW PRODUCT DEVELOPMENT PRACTICES
PublikacjaFinding the best way to develop new products has been always a hot topic for practitioners and academics. However, so far only a few of these kinds of studies have concentrated on a single industry. In this paper, we group German domestic appliance manufacturers with regards to their new product development (NPD) practices to discover their attitude to NPD effort. By conducting a survey we found that three different groups of manufacturers...
-
Degradation of Gel-Coat Layer in Glass/Polyester Laminate in Seawater Environment
PublikacjaGlass/polyester laminate coated with gelcoat layer of different thickness 0,5; 1,5; 3 mm was studied in terms of blistering behaviour and water sorption in hot water environment. Blistering was found to be accelerated for thin (0,5 mm) gel-coat layer compared to the thick (1,5; 3 mm), however no significant difference in blistering behaviour was observed between the laminates with gel-coat thickness 1,5 and 3 mm which may suggest...
-
Flow structure, heat transfer and scaling analysis in the case of thermo-magnetic convection in a differentially heated cylindrical enclosure
PublikacjaThe experimental, numerical and scaling analysis in the case of thermo-magnetic convection in a thermosyphon-like enclosure filled with a paramagnetic fluid is presented. Visualization of temperature field together with the numerical simulation gave an information about the flow structure, which indicated “finger-like” structures of hot and cold streams advecting each other. Their number depended on the Rayleigh number and also...
-
A Quantitative Investigation of Dislocation Density in an Al Matrix Composite Produced by a Combination of Micro-/Macro-Rolling
PublikacjaAn aluminum matrix composite with dispersed carbon nanotubes (CNTs) was produced via flake powder metallurgy using a micro-rolling process and vacuum hot pressing (VHP), followed by conventional rolling using a macro-rolling process. The microstructure and mechanical properties of the produced composites were studied. In addition, a new quantitative model was introduced to study the dislocation density based on the microstructural...
-
Flow Boiling in Minigap in the Reversed Two-Phase Thermosiphon Loop
PublikacjaThe paper presents the results of experimental investigations of a model of a heat exchanger featuring a minigap, which is perceived as an evaporator for an inverted thermosiphon. The system works with a single component test fluid. The tested evaporator generates pumping power in the test loop in a way similar to the mammoth pump. The tests regarded a module of the heat exchanger, consisting of a hot leg and a cold leg with the...
-
Fabrication of Bi6Fe2Ti3O18 Ceramics by Mixed Oxide Method
PublikacjaIn the present study Bi6Fe2Ti3O18 (BFTO) ceramics has been fabricated by solid state reaction from the mixture of simple oxides viz. Bi2O3, TiO2 and Fe2O3. Stoichiometric mixture of the powders was thermally analyzed so parameters of the thermal treatment were determined. The EDS measurements have shown conservation of the chemical composition of the ceramic powder after calcination. Hot-pressing method was used for final densification...
-
Charge-based deep level transient spectroscopy of B-doped and undoped polycrystalline diamond films
PublikacjaThe undoped and B-doped polycrystalline diamond thin film was synthesized by hot filament chemical vapor deposition and microwave plasma, respectively. The structural characterization was performed by scanning electron microscopy, X-ray diffraction and Raman spectroscopy. The electrical properties of synthesized diamond layer were characterized by dc-conductivity method and charge deep level transient spectroscopy. The B-doped...
-
Recent advances in aqueous virus removal technologies
PublikacjaThe COVID-19 outbreak has triggered a massive research, but still urgent detection and treatment of this virus seems a public concern. The spread of viruses in aqueous environments underlined efficient virus treatment processes as a hot challenge. This review critically and comprehensively enables identifying and classifying advanced biochemical, membrane-based and disinfection processes for effective treatment of virus-contaminated...
-
Active management of equipment cooling in hoteling data centers
PublikacjaHoteling data centers are designated for housing computing and storage units of many, usually small customers, as opposed to traditional data centers supporting own computing and storage resources of a bigger company. One of the services to be provided to consumer’s equipment is cooling. Cooling in data centers is prevalently achieved by circulating air in computer room. Efficient cooling requires delivering cold air from central...
-
Comparative study of operation of condensing and traditional boilers equipped with the ORC module for electricity generation
PublikacjaCondensing technology applied to boilers is to make full use of thermal energy contained in the fuel. That means that additionaly the heat from condensation of exhaust gases can be used for the purposes of heating the domestic hot water and to cover the demand for central heating. The study analyzed the operation of the "traditional" boiler equipped with the ORC module as the similar arrangement but with the condensing boiler....
-
Metoda f-chart w zastosowaniu do projektu instalacji solarnej w budownictwie jednorodzinnym
PublikacjaW artykule przedstawiono algorytm obliczeń cieplnych związanych z konwersją promieniowania cieplnego oraz analizę efektów pracy instalacji solarnej przy użyciu metody korelacyjnej f-chart. Zaprezentowany algorytm obliczeń cieplnych oraz omówiona w artykule podstawowa odmiana metody f-chart zostały poparte przykładem obliczeniowym dla instalacji solarnej, która wykorzystywana jest do wspomagania układu przygotowania c.w. dla potrzeb...
-
Combined operation of 900MW power plant with the ORC through the bleed steam extraction point and CO2 recovery system
PublikacjaThe work presented here is aimed at utylisation of waste heat in the reference supercritical power plant in the manner to produce electricity in ORC installation. The waste heat is available in the form of a stream of hot water at 90 C, recovered from the exhaust gases in the amount of 200MW. Such low enthalpy heat source is rather insufficient to produce a good quality vapour to feed the ORC turbine. Therefore an original approach...
-
Bio-Based Polyurethane Composites and Hybrid Composites Containing a New Type of Bio-Polyol and Addition of Natural and Synthetic Fibers
PublikacjaThis article describes how new bio-based polyol during the liquefaction process can be obtained. Selected polyol was tested in the production of polyurethane resins. Moreover, this research describes the process of manufacturing polyurethane materials and the impact of two different types of fibers—synthetic and natural (glass and sisal fibers)—on the properties of composites. The best properties were achieved at a reaction temperature...
-
Dziedzictwo techniki - spojrzenie z Gdańska
PublikacjaWe ''Wprowadzeniu'' omówiono proces wyłaniania się współczesnej doktryny dziedzictwa techniki, przywołując pojęcia: środowisko zbudowane, materialne i niematerilane dziedzictwo kultury, dziedzictwo inżynierii, archeologia przemysłu, rynek dziedzictwa, ochrona autentyczności zabytków. Wskazano współczesne zjawiska: fasadyzm, niebezpieczeństwo dewaloryzacji, lekceważenie wartości kulturowych, zanik różnorodności krajobrazu kulturowego...
-
PV installations and the safety of residential buildings
PublikacjaThe dynamic development of the photovoltaic industry entails threats that have a direct impact on the safety of residential buildings. Appropriate design of a PV installation can be a challenge due to the multifaceted nature of this issue. The designer should take into account issues related to the selection of electrical parameters of the installation, adapting lightning and surge protection in accordance...
-
Influence of type of material on performance of hydraulic components in thermal shock conditions
PublikacjaDuring the start-up of a hydraulic system in low ambient temperatures an incorrect operation may occur. The principles and conditions of safely operating hydraulic driven machines and devices are essential to designers and operators. For this reason the author of this article has conducted a series of tests on hydraulic components and systems in thermal shock conditions (cooled-down components were supplied with hot working medium)....
-
Industry 4.0 Implementation Challenges in Manufacturing Industries: an Interpretive Structural Modelling Approach
PublikacjaFor the last few years, the fourth industrial revolution, known as Industry 4.0, has been a hot topic among academics. Industry 4.0 literature involves researches presenting studies related to its different aspects including challenges, opportunities, implementation and adoption. However, a detailed study of challenges and barriers towards the Industry 4.0 implementation in manufacturing industries is missing. Hence, this paper...
-
Preliminary Citation and Topic Analysis of International Conference on Agile Software Development Papers (2002-2018)
PublikacjaThis study utilizes citation analysis and automated topic analysis of papers published in International Conference on Agile Software Development (XP) from 2002 to 2018. We collected data from Scopus database, finding 789 XP papers. We performed topic and trend analysis with R/RStudio utilizing the text mining approach, and used MS Excel for the quantitative analysis of the data. The results show that the first five years of XP...
-
Impact of reclaimed asphalt pavement (RAP) on low-temperature properties of asphalt concrete
PublikacjaHot mix recycling is a practice which enables reusing materials from old asphalt pavements. Current Polish regulations allow usage of RAP only for binder and base courses, and its amount is limited. Asphalt mixtures with RAP material have to fulfil requirements stated for typical asphalt mixtures. The research presents low-temperature properties of twelve different asphalt concretes with RAP material, determined using three-point...
-
Thermal-FSI modeling of flow and heat transfer in a heat exchangerbased on minichanels
PublikacjaIn this paper selected numerical modelling problems for an advanced thermal-FSI ("Fluid Solid Interaction") mini-channel heat exchanger model are presented. Special attention is given to the heat transfer between the separated mediums for different mass flows. Similar modelling problems have also been discussed in the literature dedicated to numerical and theoretical modelling problems for typical heat exchangers [1, 2, 3]. Basic...