Filtry
wszystkich: 187
wybranych: 183
Filtry wybranego katalogu
Wyniki wyszukiwania dla: WOOD RESISTANCE
-
Hydrogen production from wood waste by mean of dark fermentation
PublikacjaThe utilization of wood wastes in clean and green chemistry method like by mean of dark fermentation, is a highly desired solution of waste management. In the article model for the estimation hydrogen potential of wood waste is given. The model has been used to calculate the potential theoretical hydrogen mass that can be produced from wood wastes in Pomerania and Silesia: pine, spruce, fir, beech and oak. In the introduction,...
-
The Influence of Drying Temperature on Color Change of Hornbeam and Maple Wood Used as Surface and Inner Layers of Wood Composites
PublikacjaThe thermal treatment of wood changes its structure due to the degradation of wood polymers (cellulose, hemicellulose and lignin), so the physical properties of wood are either improved or degraded. Color changes apply not only to natural wood, but also to such wood composites for which some amount of glue is used in their construction (e.g., plywood, blockboard or laminboard). This article is focused on the analysis of hornbeam...
-
Effect of the Drying Method of Pine and Beech Wood on Fracture Toughness and Shear Yield Stress
PublikacjaThe modern wood converting processes consists of several stages and material drying belongs to the most influencing future performances of products. The procedure of drying wood is usually realized between subsequent sawing operations, affecting significantly cutting conditions and general properties of material. An alternative methodology for determination of mechanical properties (fracture toughness and shear yield stress) based...
-
Fracture Toughness and Shear Yield Strength Determination for Two Selected Species of Central European Provenance
PublikacjaWhen offcut of wood is formed by shearing, Atkins’s analyses of sawing processes can be applied. Using this modern approach, it is possible to determine the fracture toughness and shear yield strength of wood. This model is only applicable for the axial-perpendicular cutting direction because both of these parameters are suitable for the given direction of cutting edge movement and cannot be considered material constants. Alternatively,...
-
Influence of steam drying process on wood mechanical properties
PublikacjaResults of influence of gas-steam mixture drying process on mechanical properties of material are presented. Wood species, namely oak (Quercus L.), beech (Fagus L.), pine (Pinus L.) and spruce (Picea K.) from the northern part of Pomerania region in Poland, were subject of air-steam mixture drying process in a laboratory kiln especially arranged for that reason. Measurements of the global coefficient of elasticity and bending strength...
-
Experimental and Numerical Investigation of Tensile and Flexural Behavior of Nanoclay Wood-Plastic Composite
PublikacjaIn this study, the effect of wood powder and nanoclay particle content on composites’ mechanical behavior made with polyethylene matrix has been investigated. The wood flour as a reinforcer made of wood powder was at levels of 30, 40, and 50 wt.%, and additional reinforcement with nanoclay at 0, 1, 3, and 5 wt.%. Furthermore, to make a composite matrix, high-density polyethylene was used at levels of 70, 60, and 50% by weight....
-
Synthesis and characterization of biopolyols through biomass liquefaction of wood shavings and their application in the preparation of polyurethane wood composites
PublikacjaThe sustainability of production systems in wood processing, wood industry, and wooden waste disposal is an important issue for European industry and society. Proper development of products based on renewable wood resources gives an opportunity to provide materials with long-term environmental, social, and economic sustainability. This study aims to establish a new way of forestry and agricultural waste materials utilization by...
-
Methodology for determination of the selected mechanical properties of wood based on cutting tests
PublikacjaFrom kiln-dried spruce wood (with steam) as well as in natural conditions were randomly selected 8 samples. After determining the average dimensions, moisture content and density of the samples they have been cut on the frame sawing machine PRW15M for measurement of cutting power. Based on those results from a linear rela-tionship of cutting power versus feed per toot mechanical properties of wood such as facture toughness and...
-
THE EFFECT OF DRYING INTENSITY ON THE COLOR CHANGES OF PINE WOOD (PINUS SYLVESTRIS L.)
PublikacjaThe effect of the selection of drying process parameters on the color change of Scots pine wood (Pinus Sylvestris L.) is presented. In this work the experimental studies have been performed. The research focused on the influence of drying intensity on the changes of color after drying process. Intensity of drying process was determined on the basis of the average drying gradient. To determine the color of wood before and after...
-
The effect of beech wood (Fagus sylvatica L.) steaming process on the colour change versus depth of tested wood layer
PublikacjaThe results of experimental research on the colour changes of beech wood at different depths of the tested layer are presented. Beech wood (Fagus sylvatica L.) dried in a conventional kiln was tested. Half of the wood samples were steamed prior to the drying process. Colour changes were measured at various depths after the face milling process was used to remove the material to expose to the deeper surface. The colour changes were...
-
Influence of high temperature air-steam mixture application on time wood drying process
PublikacjaThe results of influence gas-steam mixture drying process on time wood drying process are presented. Wood species, namely oak (Quercus L.), beech (Fagus L.), pine (Pinus L.) and spruce (Picea K.) from the northern part of Pomerania region in Poland, were subject of air-steam mixture drying process. Main focus of those tests was to shorten the time of drying process and afterward to check properties of wood.
-
The differential impact of a density of Polish pine wood on cutting forces with its origin region taken into consideration
PublikacjaIn the article the dependence of cutting forces in a function the density of wood with regard to the wood origin are presented. Samples used in experiment were with Scotch pine (Pinus sylvestris L.) originating from four provenances in Poland (Figure 1). Wood density was measured by two methods: stereometric method (global density) and radiometric method (local density). Stereometric method consists in measurements the volume...
-
Cutting model parameters from frame sawing of natural and impregnated Scots pine (Pinus sylvestris L.)
PublikacjaIn this paper, absolute and density normalized cutting model parameters of natural and impregnated Scots pine (Pinus sylvestris L.) are shown and a method for the calculation of their corresponding material properties in the principal material directions of wood is presented. The parameters were determined from measurements of cutting power on a sash gang saw, and are in detail the fracture toughness and the shear yield strength...
-
Deformation and Surface Color Changes of Beech and Oak Wood Lamellas Resulting from the Drying Process
PublikacjaThe drying process was examined relative to parameters’ influence on the deformation and surface layer color changes of beech wood (Fagus sylvatica L.) and oak wood (Quercus robur L.). The goal was to analyze the impact of drying process conditions, wood and growth rings types, and load on the deformation and surface color changes of drying thin wooden elements. A further aim was to reduce the time of the lamella drying and minimize...
-
Preliminary studies on the effect of feed speed on the colour change of wood
PublikacjaThis paper presents the results of preliminary analyses of the effect of cutting parameters on changes in the colour of wood. Beech wood cut with use circular saw was analysed. The cutting parameter tested was the feed speed, represented by the feed per tooth. Sawing processes with different feed per tooth ranging from 0.0008 mm to 0.09 mm were analysed. It was observed that over the entire range of feed rate per tooth analysed,...
-
The Impact of Drying Conditions on the Surface Color Changes of Pine Wood
PublikacjaThe article presents the impact of drying process and selected parameters on the color changes on the surface of pine wood (Pinus sylvestris L.). Three predetermined process conditions (modes), mild, normal, and intensive, were investigated. The experiments were conducted using a semi-industrial scale dryer designed at the Gdańsk University of Technology with a loading capacity of 0.55 m3. The drying process was applied to pine...
-
Recent advances in compatibilization strategies of wood-polymer composites by isocyanates
PublikacjaWood-polymer composites technologies are gaining more and more attention in the scientific community, positively affecting the increase in their industrial applications, for example, automotive, building, 3D printing, etc. Many research works are focused on the improvement in matrix–lignocellulosic filler interactions to produce highly filled composites with satisfying performance properties. In this field of research, using isocyanates...
-
Using the ultrasonic tomography method to study the condition of wooden beams from historical buildngs
PublikacjaThe need to evaluate the integrity of wooden structural elements is constantly increasing. Non-destructive methods are becoming more popular in this field of research. One type of non-destructive testing is the ultrasonic imaging method, which allows the analysis of internal wood structures without disturbing their state and integrity. In this study, we are interested in assessing the effect of wood condition on the ultrasound...
-
Analysis of surface roughness of chemically impregnated Scots pine processed using frame-sawing machine
PublikacjaThe objective of this work was to evaluate the effect of the impregnation process of pine wood (Pinus sylvestris L.) on roughness parameters of the surface processed on a frame sawing. The samples weredried and impregnated using a commercial procedure by a local company. The touch method withthe use of measuring stylus (pin) was employed to determine of surface roughness of the samplesconsidering parameters, namely, arithmetical...
-
Modification of microporous polyurethane elastomers with different types of ash—morphological, mechanical, and thermal studies
PublikacjaIncorporation of wood ash particles from wood gasification into microporous polyurethane elastomers has been investigated and compared to addition of commercially available microspheres resulting from coal burning. Samples were modified with 3 and 6 wt% of fillers. Structure, mechanical, and thermal properties of obtained elastomers were investigated. Incorporation of both types of ash particles decreased the density of polyurethanes...
-
Characterization of Arctic Driftwood as Naturally Modified Material. Part 1: Machinability
PublikacjaArctic driftwood has reached the coast of Iceland for centuries. This material was used by the inhabitants of the island as a building material for houses, boats, churches and pasture fences. Nowadays, the driftwood is used in the furniture industry, for the finishing of internal and external walls of buildings and also by artists. The properties of driftwood differ to that of original resource due the long-term effects of exposure...
-
The influence of drying parameters on wood properties
PublikacjaResults of influence of gas-steam mixture drying process on wood mechanical properties are presented. Wood species, namely pine (Pinus sylvestris L.) and beech (Fagus silvatica L.) from the northern part of Pomerania region in Poland, were subject of steam kiln-drying process in a laboratory kiln specially arranged for that reason.
-
Sawing Processes as a Way of Determining Fracture Toughness and Shear Yield Stresses of Wood
PublikacjaA new computational model, based on fracture mechanics, was used to determine cutting forces. Unlike traditional computing methods, which depend on many coefficients reflecting the machining of solid wood, the new model uses two main parameters: fracture toughness and shear yield stresses. The aim of this study was to apply this new method to determine these parameters for the tooth cutting edge principal positions and longitudinal...
-
Influence of drying mode and feed per tooth rate on the fine dust creation in pine and beech sawing on a mini sash gang saw
PublikacjaThe experimental results of the study focused on the effect of drying processes of modified air drying and warm air steam mixture drying of pine and beech wood on the size of sawdust particles created in cutting using PRW-15M sash gang saw, are presented in the paper. Particle size analysis of dry sawdust was performed using two methods—sieving method and laser diffraction analysis. The results showed that the drying process did...
-
Is It Right To Predict Cutting Forces On The Basis Of Wood Density?
PublikacjaSeveral properties of wood can be correlated to wood density. It is widely accepted that the cutting power requirements are following this general assumption. Therefore, according to classic literature sources available for determination of the cutting power for both band- and circular- sawing machines, the cutting power requirements (and/or cutting forces) are computed as a function of the wood specific gravity SG. It was shown...
-
On the current state of dovetail wall-corner joints in wooden Greek Catholic churches in Polish Subcarpathia with structural and sensitivity analyses
PublikacjaThis paper describes the current condition of some dovetail joints which form the wall corners of two Greek Catholic churches of wooden construction in Polish Subcarpathia. It also gives the historical background of the sacral architecture of that region. The two structures, which represent the same type of log corner joints are situated in Chotylub and Cewków. The buildings were examined e.g. for damage, wood moisture content,...
-
Numerical analysis of the carpentry joints applied in the traditional wooden structures
PublikacjaThe paper concerns the numerical analysis of the carpentry joints made from spruce wood. The material parameters of the wood have been calculated on the basis of nine independent material constants (an orthotropic material). The contact zone between the individual elements of the connection has been determined using Contact Tables in the MSC.Marc software. Five types of carpentry joints have been analyzed. The main aim of the research...
-
Estimation of fracture toughness and shear yield stress of orthotropic materials in cutting with rotating tools
PublikacjaThe cutting force is an energetic effect of splitting material, and might be considered from a point of view of modern fracture mechanics. Forecasting of the shear plane angle in cutting broaden possibilities for modelling of the cutting process even for thin uncut chips. Such mathematical model has been developed here for description of the orthotropic materials’ cutting on the base of fracture theory, and includes work of separation...
-
Experimental examination and modification of chip suction system in circular sawing machine
PublikacjaThe article presents the results of experimental examination of the wood chip suction system in the existing sliding table saw before and after its modifi cation. The studies focused on the extraction hood of the mentioned system. The methodical experimental research of the pressure distribution inside the hood during wood chip removal for the selected rotational speed of saw blades of 3500 and 6000 min-1 with a diameter of 300...
-
A Method and Device for 3D Recognition of Cutting Edge Micro Geometry
PublikacjaA very useful method was successfully applied in the investigation of tools for machining wood and wood based composites. It allows scanning of the cutting edge micro geometry in three dimensions and reproducing it in a virtual space as a 3D surface. The application of the method opens new possibilities of studying tool wear by scanning, including the calculation of volume loss and other analysis of tool wedge geometry along and...
-
The innovative experimental rig for wood steam drying at atmospheric pressure
PublikacjaThe high cost of fossil fuel and soaring consumer interest have encouraged people in the wood industry to look for faster and more energy-efficient methods to dry lumber. The air-steam mixture as medium of drying process was used in a laboratory kiln especially arranged for that reason. Experimental rig is based on automatic control system. At the time of drying measurements of the internal temperature, wood temperature, moisture...
-
Lateral forces determine dimensional accuracy of the narrow‑kerf sawing of wood
PublikacjaThe shrinking global forest area limits the supply of industrially usable raw resources. This, in combination with the ever‑increasing consumption of timber due to population growth can lead to the lack of a positive balance between the annual volumetric growth and consumption of wood. An important innovation toward increasing environmental and economic sustainability of timber production is to reduce the volume of wood residues...
-
Na efektywność wpływa sposób przetarcia. Seminarium Obróbki Drewna w Szwecji
PublikacjaW artykule przedstawiono relację z 20th International Wood Machining Seminar, które odbyło się w Skelleftea w Szwecji.
-
Distinctive properties of Scots pine (Pinus sylvestris L.) originating from the Carpathian and Great Poland-Pomeranian of Nature and Forest Land
PublikacjaIn this paper values of properties of Scots pine, the fracture toughness and of shear yield stress in the shear zone are presented. Samples of Scotch pine (Pinus sylvestris L.) wood of two provenances from Poland were tested. These properties were determined from the values of cutting power obtained experimentally on the saw frame PRW-15M. The values of fracture toughness and shear yield stress based on the Atkins model for cutting...
-
Modelling of heat and mass transfer through wooden buildings
PublikacjaThe aim of this review paper is to examine the most recent available studies dealing with theoretical, numerical and experimental aspects related to modelling of heat and mass transfer through wooden buildings. The main thermophysical, mechanical and hygrometric properties of wood are firstly discussed. Then, the basic governing equations of heat and mass transfer phenomena are presented. A detailed description of the physical...
-
Effect of Thermal Treatment of Birch Wood by Saturated Water Vapor on Granulometric Composition of Chips from Sawing and Milling Processes from the Point of View of Its Processing to Composites
PublikacjaThe goal of this work is to investigate the impact of thermal modification of birch wood with saturated steam on the particle size distribution of the sawing and milling process. Birch wood (Betula pendula Roth) is an excellent source to produce plywood boards. Wastes from mechanical processing of birch wood are suitable to produce composite materials. Granulometric analyses of chips from sawing processes on the PRW 15M frame saw,...
-
AN ALTERNATIVE WAY OF DETERMINING MECHANICAL PROPERTIES OF WOOD BY MEASURING CUTTING FORCES
PublikacjaThe cutting force is an energetic effect of splitting material, and might be therefore considered from a point of view of modern fracture mechanics. The dedicated mathematical model developed for description of the wood cutting has been developed here on the base of fracture theory, and includes work of separation (fracture toughness) in addition to the material plasticity and friction. The effect of the cutting edge dullness is...
-
Assessment of Wooden Beams from Historical Buildings Using Ultrasonic Transmission Tomography
PublikacjaThe main goal of this study was non-destructive evaluation of wooden elements using ultrasonic waves. The inspection was carried out on wooden beams from a historical object. Elastic wave signals were processed by ultrasonic transmission tomography to obtain imaging of the internal structure of tested elements without disturbing their state and integrity. The focus was on the influence of wood anisotropy on the propagation of ultrasonic...
-
Non-destructive Testing of Wooden Elements
PublikacjaExamining the condition of wooden elements is crucial from the perspective of proper structure performance. If the deterioration in the internal wood condition, which displays no symptoms visible from the outside, is detected, the further spread of the deterioration can be prevented. Test results often point to the necessity of conducting repairs and, renovations, replacing the structure of wooden beams, or even substituting a...
-
Chip suction system in circular sawing machine: empirical research and computational fluid dynamics numerical simulations
PublikacjaThe experimental analysis of the wood chip removing system during its redesigning in the existing sliding table circular saw and computational fluid dynamic (CFD) numerical simulations of the air flow process is presented in the paper. The attention was focused on the extraction hood and the bottom shelter of the actual existing system. The main aim was to perform experimental research on the pressure distribution inside the...
-
THE EFFECT OF WOOD DRYING METHOD ON THE GRANULARITY OF SAWDUST OBTAINED DURING THE SAWING PROCESS USING THE FRAME SAWING MACHINE
PublikacjaThe experimental results of the study focused on the effect of drying processes of warm air drying at the temperature of 6580°C and warm air-steam mixture drying at the temperature of 105°C of pine and beech wood to the size of sawdust grains created by cutting using RPW 15M frame saw is presented in the paper. Particle size analysis of dry sawdust was performed using two methods - screening method and optical method based on...
-
Fracture mechanics model of cutting power versus widespread regression equations while wood sawing with circular saw blades
PublikacjaA comparison of the theoretical cutting power consumption results forecasted with the model (FM_CM model) which include work of separation (fracture toughness) in addition to plasticity and friction, and two widespread regression equations while wood sawing with circular saw blades has been described. in and cutting power consumption forecasted. In computations of the cutting power consumption during rip sawing of Scots pine wood...
-
Optimization of chip removing system operation in circular sawing machine
PublikacjaThe paper presents the optimization of the wood chips removing system in the sliding table saw. Chips are generated during the cutting of the material. The attention was focused on the upper casing of mentioned system. The methodical experimental studies of the pressure distribution inside the casing during the wood chip removing operation for the selected rotational speed of saw blade with a diameter of 300 mm and 450 mm were...
-
NUMERICAL MODELLING AND EXPERIMENTATION OF HISTORICAL CARPENTRY CORNER LOG JOINTS
PublikacjaThe main purpose of this research is to determine the stress distributions on the contact surfaces between the logs of the historical carpentry corner joints. The additional purpose is to compare the stress distribution for four different boundary conditions in the case of dry and wet pine wood. The paper presents the results of numerical analysis of the shortcorner dovetail connection and the saddle notch corner joint, which are...
-
Analyses of Shear Angle in Orthogonal Cutting of Pine Wood
PublikacjaThe determination of energy effects for wood machining processes, such as cutting power and cutting forces, is very useful in designing of manufacture process of wooden products. A more accurate prediction of cutting forces requires a correct determination of the shear angle value, which can be determined using various models. In this article, shear angle values for an orthogonal linear cutting process of pine wood are determined. The...
-
Non-Linear Analysis of Inter-Story Pounding between Wood-Framed Buildings during Ground Motion
PublikacjaPounding between adjacent buildings during ground motion may result in structural damage or lead to total destruction of structures. The research on the phenomenon has recently been much advanced; however, the analyses have been carried out only for concrete, steel, and masonry structures, while pounding between wooden buildings has not been studied so far. The aim of this paper is to show the results of detailed non-linear seismic...
-
Activated Carbon Produced by Pyrolysis of Waste Wood and Straw for PotentialWastewater Adsorption
PublikacjaPyrolysis of straw pellets and wood strips was performed in a fixed bed reactor. The chars, solid products of thermal degradation, were used as potential materials for activated carbon production. Chemical and physical activation processes were used to compare properties of the products. The chemical activation agent KOH was chosen and the physical activation was conducted with steam and carbon dioxide as oxidising gases. The eect...
-
Reminiscencje: 18. Międzynarodowe Seminarium Obróbki Drewna w Vancouver. Obróbka drewna w British Columbia
PublikacjaPrzedstawiono sprawozdanie ze zwiedzania dwu zakładów produkcyjnych usytuowanych w miejscowosci Delta (BC): Craftsman Wood Products oraz Optimil Machinery. Zwiedzanie było jednym z punktów programu 18 IWMS w Kanadzie.
-
The dying medium temperature impact on the final moisture content of pine wood at constant drying time
PublikacjaThe results of final moisture content of pine wood (Pinus sylvestris L.) after drying process are presented. The wood in the experiments was taken from the northern part of Pomeranian region in Poland. The drying process was performed in the experimental chamber equipped with the micro-jet heat exchanger. The air at temperatures of 40°C, 60°C, 80°C, 100°C and 120°C with relative humidity about 60% and atmospheric pressure was the...
-
High Temperature Drying Process of Beech Wood (Fagus sylvatica L.) with Different Zones of Sapwood and Red False Heartwood
PublikacjaThis study examined the changes in the properties of beech wood (Fagus sylvatica L.) after intense drying. Beech wood with false red heartwood was selected as the test specimen. The test samples had dimensions of 50 mm thickness, 180 mm width, and 350 mm length. The specimens were divided into two groups, false red heartwood and sapwood. These specimens were selected with different angles of the growth rings (radial and tangential)....