Filtry
wszystkich: 357
wybranych: 248
-
Katalog
Filtry wybranego katalogu
Wyniki wyszukiwania dla: DISPLACEMENT MEASUREMENTS
-
Calculation of an ultimate load value of a silo with geometric imperfections in the shape of eigenforms
PublikacjaThe ultimate load value of a silo with initial geometric imperfections was measured. The structure was loaded with wind. Imperfections were assumed as translations of the shell nodes from perfect geometry taken from eigenforms and their combinations. Two variants of the maximum deflection placement with respect to the direction of wind pressure were proposed. The first consists in applying the maximum wind pressure to the element...
-
Influence of an applied bearing system on behaviour of multi-span footbridge
PublikacjaThe cycle overpass in Gdynia is a box structure over 300 metres long, 10-span. It was opened for bicycle traffic in the second half of 2013. At the end of its construction, there was failure due to excessive horizontal displacement of the system. A number of bearings exceeded the range of permissible transverse shifts thus it was necessary to temporarily protect the spans from slipping. The FEM analysis of the original solution...
-
Usage of concentrated spectrogram for analysis of acoustical signals
PublikacjaA novel precise method of signal analysis in the time-frequency domain is presented. A signal energy distribution is estimated by discard and displacement of energy parts of the classical spectrogram. A channelized instantaneous frequency and a local group delay are used in order to energy replacement. Additionally, newly introduced representations such as: a channelized instantaneous bandwidth and a local group duration are used...
-
On the modelling of aerodynamic force coefficients for over-shroud seals of turbine stages
PublikacjaThis paper presents experimental investigations which made it possible to determine dynamic coefficients of labyrinth over-shroud seal of a model air turbine. The coefficients associate pressure forces with turbine rotor displacement, velocity and acceleration respective to turbine casing (linear model) and play important role in analyzing turbine-set dynamics. The obtained results indicated that involving serious errors can be...
-
Combined numerical and experimental approach to determine numerical model of abdominal scaffold
PublikacjaA proper junction of the prosthesis and the abdominal wall is important in successful hernia repair. The number of tacks should be balanced to assure appropriate mesh fixation and not to induce post-operative pain. Numerical simulations help to find this balance. The study is aimed at creating a proper numerical model of a knitted surgical mesh subjected to boundary conditions and load occurring in the abdominal cavity. Continuous,...
-
Medially positioned plate in first metatarsophalangeal joint arthrodesis
PublikacjaObjective The purpose of this study was to biomechanically compare the stability of first metatarsophalangeal (MTP1) joint arthrodesis with dorsally and medially positioned plates. Methods A physical model of the MTP1 joint consists of printed synthetic bones, a titanium locking plate and screws. In the experiments, samples with dorsally and medially positioned plates were subjected to loading of ground load character in a universal...
-
R&D of satellite pumps and motors with small geometrical displacement supplied with oil and non-flammable liquids
PublikacjaThe newest construction of satellite motors and self-suction satellite pumps with small geometrical displacement have been described in this article. The characteristics of volumetric and total efficiency of one satellite motor, selected from the series, supplied with oil have been presented. These characteristics have been compared with the orbital motors' characteristics. The remaining specifications of these motors were also...
-
CFGFRPT Piles with a Circular Cross-Section and their Application in Offshore Structures
PublikacjaThe possibilities of using concrete piles in a polymer composite reinforced with glass fibres in offshore facilities were shown. Laboratory tests of CFGFRPT type piles compressed axially and in eccentric compression for the analysis of CFGFRPT piles were used. Methods of analysis of dynamic systems for mathematical modelling of the displacement of the hammer in the pile driving process were applied. The possibilities of combining...
-
A comprehensive study on nonlinear hygro-thermo-mechanical analysis of thick functionally graded porous rotating disk based on two quasi three-dimensional theories
PublikacjaIn this paper, a highly efficient quasi three-dimensional theory has been used to study the nonlinear hygro-thermo-mechanical bending analysis of very thick functionally graded material (FGM) rotating disk in hygro-thermal environment considering the porosity as a structural defect. Two applied quasi three-dimensional displacement fields are assumed in which the strain along the thickness is not zero unlike most of the other plate...
-
A variational approach of homogenization of piezoelectric composites towards piezoelectric and flexoelectric effective media
PublikacjaThe effective piezoelectric properties of heterogeneous materials are evaluated in the context of periodic homogenization, whereby a variational formulation is developed, articulated with the extended Hill macrohomogeneity condition. The entire set of homogenized piezoelectric moduli is obtained as the volumetric averages of the microscopic properties of the individual constituents weighted by the displacement and polarization...
-
Effectiveness of a mathematical model in simulating nonlinear mechanical behaviour of a seismic isolation system made of polymeric bearings
PublikacjaThe present study was focused on determining the effectives of a nonlinear mathematical model in simulating complex mechanical behaviour of a seismic isolation system made of Polymeric Bearings. The proposed mathematical model defines the lateral force as a nonlinear function of the shear displacement and the deformation velocity. The effectiveness of the proposed mathematical model was verified by comparing the seismic response...
-
Impact of an unsecured excavation on an underground pipeline
PublikacjaThe paper presents a numerical analysis of the impact of an unsecured excavation on an underground pipeline in selected soil conditions. The research was inspired by a real-life failure of a water pipeline which was caused by a nearby unsecured excavation (Sikora et al. 2015). The failure was triggered by displacement of soil mass in the vicinity of the pipeline. The study conducted in the framework of Finite Element...
-
Two tests for adhesive bonding long term characterization: principles and applications
PublikacjaThis article describes recent refinement of the traditional wedge test technique used to characterize durability of the adhesive joints. We propose two types of measuring protocols to monitor precisely and continuously the propagation of an "effective" crack during long term mode I fracture mechanic test. First method is directly derived from the traditional wedge test technique and consist in monitoring the surface strain of adherent...
-
Pile Model Tests Using Strain Gauge Technology
PublikacjaOrdinary pile bearing capacity tests are usually carried out to determine the relationship between load and displacement of pile head. The measurement system required in such tests consists of force transducer and three or four displacement gauges. The whole system is installed at the pile head above the ground level. This approach, however, does not give us complete information about the pile-soil interaction. We can only determine...
-
A numerical model to simulate the motion of a lifesaving module during its launching from the ship’s stern ramp
PublikacjaThe article presents a numerical model of object motion in six degrees of freedom (DoF) which is intended to be used to simulate 3D motion of a lifesaving module during its launching from a ship using a stern ramp in rough sea. The model, of relatively high complexity, takes into account both the motion of the ship on water in changing sea conditions, and the relative motion of the ramp with respect to the ship. The motion of the...
-
Comparison of the powers of energy losses in a variable capacity displacement pump determined without or with taking into account the power of hydraulic oil compression
PublikacjaPowers of energy losses in a variable capacity displacement pump are compared with or without taking into account the power of hydraulic oil compression. Evaluation of power of liquid compression in the pump was made possible by the use of method, proposed by the Author, of determining the degree of liquid aeration in the pump. In the method of determining the liquid aeration in the pump and of powers of volumetric losses of liquid...
-
Techniki sprzętowej teselacji do wygładzania i uszczegóławiania modeli trójwymiarowych
PublikacjaDirectX 11 oraz OpenGL 4 wprowadziły do potoku renderującego bardzo oczekiwaną teselację. Wraz z upływem czasu coraz więcej silników graficznych zostaje dostosowywanych do wspierania tej technologii. W artykule przedstawiona została koncepcja teselacji od strony teoretycznej oraz praktycznej. Opisany został nowy potok renderujący, a w szczególności dedykowane teselacji programy cieniujące (ang. shaders). Główną część artykułu stanowi...
-
Mesoscopic simulations of crack propagation in concrete using cohesive elements
PublikacjaThe paper presents results of two-and three-dimensional meso-scale simulations of fracture in notched concrete beams subjected to three-point bending test. Concrete was assumed as a 3-phase material composed of aggregate grains placed in the cement matrix with Interfacial Transitional Zones (ITZs) between then. In 2D simulations macro-voids were also taken into account. The particle distribution was taken from real concrete beams...
-
Techniki sprzętowej teselacji do wygładzania i uszczegóławiania modeli trójwymiarowych
PublikacjaDirectX 11 oraz OpenGL 4 wprowadziły do potoku renderującego bardzo oczekiwaną teselację. Wraz z upływem czasu coraz więcej silników graficznych zostaje dostosowywanych do wspierania tej technologii, więc nie można pozostawać wobec niej obojętnym. W artykule przedstawiona zostanie koncepcja teselacji od strony teoretycznej oraz praktycznej. Opisany zostanie nowy potok renderujący, a w szczególności dedykowane teselacji programy...
-
Fractional Calculus Evaluation of Hyaluronic Acid Crosslinking in a Nanoscopic Part of Articular Cartilage Model System
PublikacjaThis work presents a study of the mechanism of physical crosslinking of hyaluronic acid in the presence of common phospholipids in synovial joint organ systems. Molecular dynamic simulations have been executed to understand the formation of hyaluronan networks at various phospholipid concentrations. The results of the simulations suggest that the mechanisms exhibit subdiffusion characteristics. Transportation quantities derive...
-
On the interspike-intervals of periodically-driven integrate-and-fire models
PublikacjaWe analyze properties of the firing map, which iterations give information about consecutive spikes, for periodically driven linear integrate-and-fire models. By considering locally integrable (thus in general not continuous) input functions, we generalize some results of other authors. In particular, we prove theorems concerning continuous dependence of the firing map on the input in suitable function spaces. Using mathematical...
-
Timber-frame house resistant to dynamic loads - analysis of wall panel filled with polyurethane foam
PublikacjaThe present study shows the experimentally and numerically determined response of a single timber-frame house wall panel filled with polyurethane (PU) foam under dynamic loads. The harmonic tests were conducted for the following frequencies: 0.5 Hz, 1.0 Hz, 2.0 Hz and 5.0 Hz for various values of the specified displacement. Based on the results of the comparison between the experimental tests and the numerical analyses, the numerical...
-
AN ATTEMPT AT IDENTIFYING THE INFLUENCE OF TEST HEAD ASSEMBLY STIFFNESS ON THE RESULTS OF A TRIBOLOGICAL EXPERIMENT CONDUCTED UNDER MICRO-OSCILLATION CONDITIONS
PublikacjaThe outcome of experimental research on a group of dry bearing materials carried out under small oscillation conditi ons and using a test rig designed and made at Gdansk University of Technology inspired the decision to find out if the stiffness of test head elements in fluenced the generated results. Therefore, a computer model utilising finite elements was devised and used to simulate the workings of the test head. The mode l...
-
A New Geodetic Method of Examination of Geometrical Conditions of a Crane Bridge
PublikacjaSafety is one of the key aspects related to crane-based material transport. In order to ensure safe crane operation and material transport, it is necessary to meet certain geometrical conditions. The authors addressed the geometrical conditions of a crane bridge, a substantial crane component. The paper presents the method to compute displacement components of points on the top of a bridge crane relative to their design position....
-
An innovative method of measuring the extension of the piston rod in hydraulic cylinders, especially large ones used in the shipbuilding and offshore industry
PublikacjaThe article presents the results of selected works related to the wider subject of research conducted at the Faculty of Mechanical Engineering and Shipbuilding at the Gdańsk University of Technology, regarding designing various on board devices with hydraulic drive for ships and other offshore facilities. One of the commonly used these mechanisms are hydraulic actuators with the measurement of the piston rod extension. The issue...
-
A Multifunctional Microwave Filter/Sensor Component Using a Split Ring Resonator Loaded Transmission Line
PublikacjaThis research is focused on the design and realiza2 tion of a microwave component with multifunctional filter/sensor 3 operation using a resonator-loaded transmission line (TL). It is 4 shown that while the structure acts as a bandstop filter, the 5 phase of the reflection coefficient from the loading resonator(s) 6 on a movable layer can be used for displacement sensing, thus 7 allowing for combining filtering with sensing in...
-
Experimental ultimate strength assessment of stiffened plates subjected to marine immersed corrosion
PublikacjaThis study experimentally analyses the impact of marine immersed corrosion degradation on the compressive strength of the stiffened plates where the lower degradation levels were considered. The corrosion degradation test was accelerated by controlling the natural corrosion environmental factors, avoiding applying an electric current. Different groups of corrosion degradation levels and initial plate thicknesses were investigated....
-
Timber Frame Houses with Different Insulation Materials - Seismic Analysis
PublikacjaThe aim of this article is to present results of a dynamic numerical analysis focused on the response of two timber frame building structures exposed to seismic excitations. The first structure was insulated with mineral wool, while the second one with polyurethane foam. Specifications and technology involved in the models' construction are based on the previously conducted experimental study, upon which numerical structural models...
-
Linear Pantographic Sheets: Existence and Uniqueness of Weak Solutions
Publikacjawe address the well-posedness of the planar linearized equilibrium problem for homogenized pantographic lattices. To do so: (i) we introduce a class of subsets of anisotropic Sobolev’s space as the most suitable energy space E relative to assigned boundary conditions; (ii) we prove that the considered strain energy density is coercive and positive definite in E ; (iii) we prove that the set of placements for which the strain...
-
Performance of isotropic constitutive laws in simulating failure mechanisms in scaled RC beams
PublikacjaResults of numerical calculations of reinforced concrete (RC) beams are presented. Based on experimental results on longitudinally reinforced specimens of different sizes and shapes are investigated. Four different continuum constitutive laws with isotropic softening are used: one defined within continuum damage mechanics, an elasto-plastic with the Rankine criterion in tension and the Drucker-Prager criterion in compression, a...
-
Numerical analysis of a temporary steel grandstand
PublikacjaThe purpose of this paper is to present the results of the numerical analysis focused on the response of the temporary steel scaffolding grandstand subjected to human-induced vibrations due to jumping. Shell as well as beam elements have been used in the numerical model. Its first stage has involved conducting modal analysis in order to determine the modes of free vibrations and the corresponding natural frequencies for the empty...
-
1,3,4-Thiadiazole-based diamides: Synthesis and complexation properties
PublikacjaAromatic diamides, derivative of 2,6-pyridinedicarboxylic acid and isophthalic acid, bearing 1,3,4-thiadiazole residue were prepared with satisfactory yields in conventional procedures and microwave stimulated reactions. X-ray structure of N,N-bis (1,3,4-thiadiazol-2-yl)-2,6-pyridinedicarboxamide (2) DMSO solvate (2DMSO) was described. Selective zinc(II), lanthanum(III), terbium(III) and L-tyrosine recognition was found for N,N-bis(1,3,4-thiadiazol-2-yl)-2,6-pyridinedicarboxamide...
-
Formation and Growth of the Crack in Bonded Joints Under Mode I Fracture: Substrate Deflection at Crack Vicinity
PublikacjaAdhesive bonding is now commonly used in aircraft, cars, boats, etc. In these applications, thin panels are often bonded. In such thin structures, heterogeneous mechanical loading along the bondline edge (or potential crack front), is likely to arise due to 3D structural effects. The crack front and its vicinity is a special region, in that it is where structural properties of the adherend material meet those of the adhesive (discontinuity)....
-
Estimation and Prediction of Vertical Deformations of Random Surfaces, Applying the Total Least Squares Collocation Method
PublikacjaThis paper proposes a method for determining the vertical deformations treated as random fields. It is assumed that the monitored surfaces are subject not only to deterministic deformations, but also to random fluctuations. Furthermore, the existence of random noise coming from surface’s vibrations is also assumed. Such noise disturbs the deformation’s functional models. Surface monitoring with the use of the geodetic levelling...
-
On existence and uniqueness of weak solutions for linear pantographic beam lattices models
PublikacjaIn this paper, we discuss well-posedness of the boundary-value problems arising in some “gradientincomplete” strain-gradient elasticity models, which appear in the study of homogenized models for a large class ofmetamaterials whosemicrostructures can be regarded as beam lattices constrained with internal pivots. We use the attribute “gradient-incomplete” strain-gradient elasticity for a model in which the considered strain energy...
-
Mathematical model defining volumetric losses of hydraulic oil compression in a variable capacity displacement pump
PublikacjaThe objective of the work is to develop the capability of evaluating the volumetric losses of hydraulic oil compression in the working chambers of high pressure variable capacity displacement pump. Volumetric losses of oil compression must be determined as functions of the same parameters, which the volumetric losses due to leakage, resulting from the quality of design solution of the pump, are evaluated as dependent on and also...
-
Timber frame houses resistant to dynamic loads - seismic analysis
PublikacjaThe aim of the article is to present results of seismic analysis results of two real-sized timber frame buildings subjected to seismic excitations. The first model was insulated with mineral wool, the second one with polyurethane foam. Technology and specifications involved in both models construction is based on the previously conducted experimental research on timber frame houses, including wall panels tests, wall numerical models...
-
LDFEM analysis of FDP auger installation in cohesive soil
PublikacjaThis paper deals with large deformation finite element (LDFE) preliminary modelling of Full Displacement Pile (FDP) installation in cohesive soil deposit located in Jazowa, Poland. The detailed FDP auger geometry is applied and the drilling process is modelled with full 3D Coupled Eulerian-Lagrangian (CEL) formulation. The total stress approach and elastic-perfectly plastic model with rate-dependent Mises plasticity is used. The...
-
A Direct Modulation for Matrix Converters based on the Onecycle Atomic operation developed in Verilog HDL.
PublikacjaThis paper presents a fast direct Pulse Width Modulation (PWM) algorithm for the Conventional Matrix Converters (CMC) developed in Verilog Hardware Description language (HDL). All PWM duty cycle calculations are performed in one cycle by an atomic operation designed as a digital module using FPGA basic blocks. The algorithm can be extended to any number of output phase. The improved version of the discontinuous Direct Analytic...
-
CONSTRUCTION TECHNOLOGY OF TIMBER-FRAME HOUSES RESISTANT TO DYNAMIC LOADS – STUDY ON MODELS OF EXTERIOR WALLS
PublikacjaThe aim of this paper is to show the numeric representation of experimental studies concerning the behaviour of exterior wall models of a timber-frame house under harmonic loading. A single wall model according to traditional technology of timberframe house walls (filling with mineral wool) was tested. The analysis was conducted for the following frequencies: 0.5 Hz, 1.0 Hz, 2.0 Hz and 5.0 Hz for various values of the specified...
-
An Intergrated Model of Motion, Steering, Positioning and Stabilization of an Unmanned Autonomous Maritime Vehicle
PublikacjaIn the paper the aim of an interdisciplinary research is presented. The research method is introduced. An object the unmanned autonomous maritime vehicle is briefly described. The key research problem concerns a combined model of the vehicle motion including the loads of lift and hydrodynamic nature. The model takes into account the gravity and displacement forces, resistance and thrust forces, lift and other hydrodynamic forces....
-
3D Monitoring - Identification of measurement problems at larger movements of the tracked points
PublikacjaAuthors identified the problems associated with the determination of the controlled points coordinates by use of automated Total Station placed behind transparent barrier. Important thing in the mentioned analysis was a large change of controlled points position and not stable Total Station’s stand (because of stand’s thermal drift). This two elements, combined with measurement made through glass plate determine the need for impact...
-
Evaluation of losses in a hydraulic motor based on the SWSB - 63 motor tests
PublikacjaIn this paper are compared two models of energy losses: that suggested by Prof. Paszota,Z. in monograph "Energy losses in the hydraulic displacement motors - definitions and relations serving the evaluation of the efficiency of hydrostatic drive" [18] and that ofProf. Balawender, A. in "Energy analysis and methodology of testing of low-speed hydraulic motors" [1]. By using the data obtained from the tests of SWSB-63 hydraulic motors...
-
The influence of water and mineral oil on volumetric losses in the displacement pump for offshore and marine applications
PublikacjaIn this paper volumetric losses in a positive displacement pump supplied with water and mineral oil are described and compared. The experimental tests were conducted using a prototype of a satellite pump (with a non-circular tooth working mechanism). In this paper the sources of volumetric losses in this pump are characterised. On this basis, a mathematical model of these losses has been presented. The results of the calculation...
-
On the plastic buckling of curved carbon nanotubes
PublikacjaThis research, for the first time, predicts theoretically static stability response of a curved carbon nanotube (CCNT) under an elastoplastic behavior with several boundary conditions. The CCNT is exposed to axial compressive loads. The equilibrium equations are extracted regarding the Euler–Bernoulli displacement field by means of the principle of minimizing total potential energy. The elastoplastic stress-strain is concerned...
-
Improvement of Performance Level of Steel Moment-Resisting Frames Using Tuned Mass Damper System
PublikacjaIn this paper, parameters of the tuned mass dampers are optimized to improve the performance level of steel structures during earthquakes. In this regard, a six-story steel frame is modeled using a concentrated plasticity method. Then, the optimum parameters of the Tuned Mass Damper (TMD) are determined by minimizing the maximum drift ratio of the stories. The performance level of the structure is also forced to be located in a...
-
Identification of residual force in static load tests on instrumented screw displacement piles
PublikacjaOccurrence of the so-called residual force of an unknown value significantly disturbs interpretation of static load tests performed on piles equipped with additional measuring instruments. Screw displacement piles are the piling technology in which the residual force phenomenon is very common. Its formation mechanism is closely related to the installation method of this type of piles, which initiates generation of negative pile...
-
Two-dimensional simulations of concrete fracture at aggregate level with cohesive elements based on X-ray lCT images
PublikacjaThe paper presents results of two-dimensional meso-scale simulations of fracture in notched concrete beams subjected to three-point bending test. Concrete was assumed as a 4-phase material composed of aggregate grains placed in the cement matrix, interfacial transitional zones (ITZs) and macro-voids. The particle distribution was taken from real concrete beams on the basis of X-ray lCT images. Comprehensive numerical analyses were carried...
-
Modelling of laminated glass PVB walls of buildings exposed to vehicle impact with different speeds
PublikacjaThis paper presents an analytical model, developed for laminated glass subjected to a low-velocity impact. It has the ability to capture glass cracks as well as large non-linear deformations. It is based mathematically on the firstorder deformation concept, which considers the effect of membrane and transverse shear as well as bending. This theory uses damage mechanics to capture the glass cracking. For this purpose, several experiments...
-
Developing a methodology for model tests of floating platforms in a towing tank of low depth
PublikacjaThe paper presents two ways to mooring model of semi-submersible platform for research in the small depth towing pool. The tested model was made in the likeness of 1:100 Thunder Horse platform moored in the Gulf of Mexico at a depth of 1,920 m. Its mooring system consisted of 16 semi-taut mooring lines (chain-wire-chain) spaced Star-shape and attached at the bottom to the suction piles. The tests were performed in the towing pool...