Wyszukiwarka
Filtry
wszystkich: 262
wybranych: 249
Wyniki wyszukiwania dla: MARINE TURBINE COMBUSTION ENGINES
-
Possibility of defining theoretical operation for diesel mengines in energy terms
PublikacjaPrzedstawiono propozycję wartościowania (ilościowego określenia) działania dowolnego silnika o zapłonie samoczynnym, na przykładzie okrętowego silnika głównego, w którym zachodzą oddziaływania energetyczne w określonym czasie. Działanie to rozumiane jest jako przekazywanie energii śrubie napędowej w ustalonym czasie, w którym zachodzi przetwarzanie i przenoszenie energii w formie pracy bądź ciepła. Wartościowanie działania silników...
-
The influence of fuel type on heat balance of medium-speed engine
PublikacjaW artykule zaprezentowano analizę wpływu rodzaju zastosowanego paliwa na bilans cieplny silników średnioobrotowych stosowanych w energetyce stacjonarnej. Przedmiotem analizy są silniki ZS i ZI zasilane gazem ziemnym oraz silniki ZS zasilane olejem napędowym. Dodatkowo analizę uzupełniono o wyniki obliczeń wykonanych dla silników dwupaliwowych, tzn. silników, w których zapłon mieszanki paliwowo gazowej realizowany jest przez pilotażowy...
-
Analysis of balancing of four stroke V6 engines
PublikacjaAnalysis of balance of V6 engines with a common-pin crankshaft depending on a cylinder bank angle and the crank radius to connecting rod length ratios , based on the relations derived, is presented in the paper. The bank angles providing the lowest moment of inertia forces in reciprocating motion, for selected values, were determined. The position of the plane of the main counterweights in order to maximum balance of the moment...
-
Model of the hydraulic pump powertrain of refuse collection vehicle compaction mechanism
PublikacjaW pracy przedstawiono symulację pracy układu napędowego pompy hydraulicznej mechanizmu prasującego śmieciarki oraz wpływ różnych konfiguracji elementów składowych tego urządzenia na zużycie paliwa silnika napędowego w warunkach przyjętego cyklu obciążenia. W tym celu wykorzystano model układu napędowego pompy hydraulicznej mechanizmu prasującego śmieciarki w formie grafów wiązań oraz wyniki pomiarów ciśnienia roboczego w siłownikach...
-
Identification of diagnostic parameter sensitivity during dynamic processes of a marine engine
PublikacjaChanging some parameters of the engine structure alters the emission of harmful components in the exhaust gas. This applies in particular to the damage of charge exchange system as well as fuel system and engine supercharger. These changes are much greater during the dynamic states and their accompanying transitional processes. The different sensitivity of diagnostic parameters to the same force, coming from the engine structure, but...
-
Analysis of accumulation possibility of energy dissipated in the braking process of train driven by hybrid locomotive
PublikacjaW tradycyjnym procesie hamowania cała energia kinetyczna lub potencjalna pociągu napędzanego lokomotywą z silnikiem spalinowym jest rozpraszana do otoczenia w postaci energii cieplnej. W lokomotywach hybrydowych istnieje możliwość odzyskania części tej energii przez przekazanie jej do akumulatorów i ponowne wykorzystanie do napędu pociągu. W pracy przedstawiono model układu napędowego lokomotywy hybrydowej z silnikiem spalinowym,...
-
Comparison of energy efficiency of vehicles powered by different fuels
PublikacjaNajpopularniejsza metoda oceny efektywności energetycznej pojazdów samochodowych polega na porównywaniu przebiegowego zużycia paliwa osiągniętego w warunkach wybranego testu homologacyjnego. Warunki eksploatacji, zdefiniowane za pomocą przebiegów prędkości w czasie, dotyczą najczęściej tylko dwóch kategorii: jazdy miejskiej i pozamiejskiej. Problemy wynikające z takiego sposobu postępowania zostały omówione na przykładzie analizy...
-
Evaluation of the significance of the effect of the active cross-sectional area of the inlet air channel on the specific enthalpy of the exhaust gas of a diesel engine using statistics F of the Fisher-Snedecor distribution
PublikacjaThis paper presents the application of Fisher-Snedecor distribution F statistics to assess the significance of the influence of changes in the active cross-sectional area of the inlet air channel (Adol) flow in a diesel engine on the observed diagnostic parameter determined on the basis of measurements of the quick changing exhaust gas temperature in the outlet channel, which is the specific enthalpy of the exhaust gas stream within...
-
INVESTIGATIONS OF THE LABORATORY FARYMANN DIESEL ENGINE D10 TYPE BY MEANS OF A LANGMUIR PROBE
PublikacjaA precise determination of the crankshaft angular position, at which fuel ignition occurs in the SI engine, enables credible diagnosis of the technical state of its working space as well as of the fuel feed system. An observation of the Langmuir probe signal provides entirely new possibilities for engine diagnostics. The probe is introduced into the working space of a cylinder through its indicator valve. This paper presents the...
-
Effect of the absence of clear contractual conditions for the pur-chase of combined heat and power systems through public tenders
PublikacjaW artykule przedstawiono dyskusję konsekwencji stosowania różnych podejść do obliczeń kontraktowych parametrów technicznych zespołów kogeneracyjnych. Obliczenia te wykonywane są na potrzeby oferty przygotowywanej w związku z ogłoszeniem przetargu publicznego na zakup siłowni kogeneracyjnej. Brak precyzyjnych zasad określających warunk, i jakie należy przyjąć do wyznaczania parametrów kontraktowych zespołów kogeneracyjnych umożliwia...
-
Dual fuelling of truck CI engine with diesel oil and mixture of propane and butane
PublikacjaW artykule przedstawiono zasadę działania dwupaliwowego zasilania jednocześnie olejem napędowym i odparowanym LPG silnika samochodu ciężarowego. Pokazano korzyści wynikające ze zużycia tańszego paliwa zbadane doświadczalnie.
-
Diagnosis in the power piston machines
PublikacjaW artykule przedstawiono obecne techniki monitorowania pracy silników i sprężarek dużej mocy. Ze względu na znaczne koszty ewentualnego wyłączenia z ruchu tego typu maszyn są one poddane obserwacji dla przewidywania ewentualnych awarii oraz planowych zatrzymań. Rośnie liczba zaawansowanych systemów pomiarowych z indykowaniem cylindrów. Dawne metody wibroakustyczne zastępowane są pomiarami parametrów procesu termodynamicznego. Słowa...
-
Development trends of automotive engine cooling systems
PublikacjaDzięki daleko idącym modyfikacjom układów zasilania i zapłonu silników samochodowych oraz udoskonaleniom układów oczyszczania spalin uzyskano znaczne zmniejszenie emisji związków toksycznych. Układy chłodzenia z pompą cieczy napędzaną mechanicznie stają się archaiczne nie pozwalając na swobodne sterowanie obiegiem cieczy. Również różna wartość temperatury potrzebnej do schładzania różnych procesów wymaga sterowanych zaworów trójdrożnych...
-
Problemy oszacowania trwałości i niezawodności silników o zapłonie samoczynnym z zastosowaniem teorii procesów semimarkowskich i diagnostyki
PublikacjaW artykule przestawiono znaczenie trwałości i niezawodności silników o zapłonie samoczynnym w eksploatacji systemów technicznych, w których są zastosowane. Wykazano, że do oszacowania trwałości i niezawodności wspomnianych silników bardziej przydatne są modele opracowane w formie semimarkowskiego procesu zmian stanów technicznych tego rodzaju silników w porównaniu do modeli proponowanych w klasycznej teorii niezawodności. Scharakteryzowano...
-
A PROPOSAL OF A DESCRIPTION OF THE OPERATING CONDITIONS OF DIESEL-ELECTRIC LOCOMOTIVES
PublikacjaThe paper presents a proposal of a description of the operating conditions of diesel-electric locomotives. The proposal is a result of the operational experience and the analysis of the locomotive operation. It constitutes a significant simplification in relation to the descriptions currently used by domestic carriers. The paper also presents examples of analyses of the operating conditions of locomotives using the proposed method.
-
Comparative analysis of balancing of V6 engines with common- and split-pin crankshafts
PublikacjaAn analysis of balancing of V6 engines equipped with split-pin crankshafts with any cylinder bank angle based on the mathematical relations derived in the paper was carried out. A comparison of the quality of their balancing with engines equipped with common-pin crankshafts was also carried out. The bank angle ranges beneficial for balancing of moments of inertia forces in reciprocating motion were determined. A mathematical relation...
-
Gas turbines – technological development and potential use in CAES systems
PublikacjaThis article briefly describes Compressed Air Energy Storage (CAES), focusing on the technological development of one of the key elements of such systems – the gas turbines. It presents the basic parameters and features of gas turbines, as well as turbine classes with example models. Main tendencies in the structural and technological development are discussed. Changes and trends on electric energy markets are becoming more and...
-
Utilization of the zero unitarization method for the building of a ranking for diagnostic marine engine parameters
PublikacjaChanging some of the parameters of the engine structure affects the emission of harmful components in the exhaust gases This primarily concerns damage in the cargo exchange system as well as in the fuel system and engine boost system. Changes in emissions of harmful compounds are often ambiguous, depending largely on the parameters that shape the combustion process. An additional problem is that often simple but undesired interactions...
-
Analysis of the structure of the atomized fuel spray with marine diesel engine injector in the early stage of injection
PublikacjaThis paper presents the results of the experimental research of the atomized fuel spray with the marine diesel engine injector in the constant volume chamber. The specificity of the phenomena occurring in the marine engine cylinder was the reason to use the optical visualisation method in the studies – the Mie scattering technique. This work presents an analysis of the influence of different geometry of outlet orifice and opening...
-
Adoption of the F-statistic of Fisher-Snedecor distribution to analyze importance of impact of modifications of injector opening pressure of a compression ignition engine on specific enthalpy value of exhaust gas flow
PublikacjaThis article analyzes the effect of modifications of injector opening pressure on the operating values of a compression ignition engine, including the temperature of the fumes. A program of experimental investigation is described, considering the available test stand and measurement capabilities. The structure of the test stand on which the experimental measurements were conducted is presented. The method of introducing real modifications...
-
Analysis of the possibility of determining the general characteristics using the operational data of a vehicle engine
PublikacjaThe paper presents an analysis of the possibility of determining the general characteristics using the operational data of an engine of refuse collection vehicle. Data acquisition was done by reading information from the CAN network using FMS standard (Fleet Management System), which is widely used in heavy duty vehicles since year 2002. The paper presents the analysis of the expected measurement uncertainties resulting from the...
-
The influence of settable parameters of switching gasoline/LPG on exhaust toxic emissions
PublikacjaThe main objective of the studies shown in the paper was to develop a proper strategy for settable parameters of ECU to decrease total emission of toxic components in composition of exhaust during a cold start phase. The experimental research has been performed for engine running at idle and for engine running on the chassis dynamometer (performing European Driving Test NEDC).
-
Signal filtering method of the fast-varying diesel exhaust gas temperature
PublikacjaThe paper presents the problem of the impact of external distortions originating on laboratory test stands on the results of measurements of fast-varying diesel exhaust gas temperature. It has been stressed how significant the aspect of the test stand adaptation is during an experiment to ensure the smallest possible impact. This paper, however, focuses on the methods of mathematical processing of a signal recorded during experimental...
-
Thermal efficiency investigations on the self-ignition test engine fed with marine low sulfur diesel fuels
PublikacjaWithin the article an issues of implementing the new kinds of marine diesel fuels into ships’ operation was described taking into ac-count restrictions on the permissible sulphur content introduced by the International Maritime Organization. This is a new situation for ship owners and fuel producers, which forces the necessity to carry out laboratory research tests on especially adapted engine stands. How to elaborate the method...
-
The influence of the fuel spray nozzle geometry on the exhaust gas composition from the marine 4-stroke diesel engine
PublikacjaThe paper presents experimental research on a 4-stroke, 3-cylinder, turbocharged AL25/30 Diesel engine. Research consisted in investigating the effect of the geometry of the fuel injectors on the exhaust gas composition from the engine. During measurements, the engine was operated with a regulator characteristic of a load range from 40 kW to 280 kW, made by electric water resistance. The engine was mechanically coupled to the electric...
-
The effectivness of fault detection in common rail injectors examination methods
PublikacjaThe article presents the effectiveness tests of fault detection in common rail injectors. 40 injectors with different wear levels were tested. Testing was made on two test benches of a completely different design. Research includes comparison of accuracy, reproducibility and testability to detect specific defects. A device was created for visualization of the fuel injector spraying steam.
-
Tyre rolling resistance and its influence on fuel consumption
PublikacjaRolling resistance of tyres is one of the major resistive forces acting on any wheeled vehicle. Unfortunately, it is also one of the forces very difficult to measure. It is estimated that in certain traffic conditions (like for example constant speed driving with slow or moderate speed) so called Rolling Resistance Impact Factor may be as high as 0.3. This means that reduction of rolling resistance by 50% would lead to 15% of energy...
-
Analysis of the regenerative braking process for the urban traffic conditions
PublikacjaIn a regular drive system, with an internal combustion engine, vehicle braking is connected with the unproductive dissipation of kinetic and potential energy accumulated in the mass of the vehicle into the environment. This energy can constitute up to 70% of the energy used to drive a vehicle under urban conditions. Its recovery and reuse is one of the basic advantages of hybrid and electric vehicles. Modern traffic management...
-
Analysis of operations of combined STIG installation
PublikacjaSteam injection in gas turbines is interesting technology with good energetic and ecological properties of gas turbines. In these applications the heat of exhaust gases is used to produce steam, which is injected in the combustion chamber of a gas turbine. The steam injection increase the power and efficiency of the installation. there are some possibilities to increases the properties of STIG turbines, for example by meas of additional...
-
Negative CO2 Emission Gas Power Plant As Technology for Utilization of Sewage Sludge, Production of Electrical Energy, and CO2 Capture - Case of Chamber Under Transpiration Cooling
PublikacjaThis work focuses on the concept developed in the nCO2PP project, which aims to demonstrate a technology that allows to achieve negative CO2 emissions through Carbon Capture and Storage (CCS) applied to sewage sludge. A feedstock is first gasified, then the resulting syngas is burned in a semi-closed oxy-fuel gas turbine with pure oxygen and water, using the advantages of oxy-combustion, to ease the capture of CO2 in the resulting...
-
Performance and emission characteristics of diesel engines running on gaseous fuels in dual-fuel mode
PublikacjaConventional fossil fuels are being substituted with alternative green fuels because of their greenhouse gas emissions and pollution problems, which pose a severe threat to the environment. Several studies have reported the usage of biodiesel and gaseous fuels in both single and dual-fuel modes. Gaseous fuels such as producer gas, biogas, syngas, and hydrogen produced from renewable biomass could potentially be used along with...
-
An energetic analysis of a gas turbine with regenerative heating using turbine extraction at intermediate pressure - Brayton cycle advanced according to Szewalski's idea
PublikacjaIn this paper, a modification of a simple gas turbine into the Brayton cycle with regenerative heating, using turbine extraction at intermediate pressure, is presented. The main concept of the retrofitting is based on the transfer of heat from the turbine exhaust gases to the air entering the combustion chamber. The extracted gas transfers heat to air via the divided regenerative heat exchanger and after that is compressed and...
-
APPLICATION OF THE THEORY OF SEMI-MARKOV PROCESSES TO DETERMINE A LIMITING DISTRIBUTION OF THE PROCESS OF CHANGES OF ABILITY AND INABILITY STATES OF FUEL SUPPLY SYSTEMS IN HEAVY FUEL DIESEL ENGINES
PublikacjaThe paper presents applicability of the theory of semi-Markov processes to determine a limiting distribution of the process of changes of technical states of fuel systems for marine engines running on heavy fuel oils. The proposed study of this process includes the components of such fuel systems like: 1 - injectors, 2 - high pressure hoses, 3 - injection pumps, 4 - low pressure hoses, 5 – fine filters, 6 - coarse filters, 7 – fuel-feed...
-
Simplified method of water cooled exhaust system design.
PublikacjaThe water cooled exhaust systems are not often used onboard ships. Prime goal is to lower temperature of exhaust gas from main propulsion and auxiliary engines to the defined limit. The design of such systems require detailed analysis of propulsion system operational parameters to meet designer expectations. The paper outlines the cooled exhaust system design problems in specific application. The simplified method of evaluation...
-
OPTIMIZATION OF THE LAST STAGE OF GAS-STEAM TURBINE USING A HYBRID METHOD
PublikacjaThis paper relates to the CFD calculation of a new turbine type which is in the phase of theoretical analysis, because the working fluid is a mixture of steam and gas generated in wet combustion chamber. At first, this article concentrates on a possibility of streamlining the flow efficiency of a last stage of axial turbine working on gas-steam mixture using a hybrid of the particle swarm optimization algorithm with the Nelder-Mead...
-
Power enhancement of the Brayton cycle by steam utilization
PublikacjaThe paper presents thermodynamic analysis of the gas-steam unit of the 65 MWe combined heat and power station. Numerical analyses of the station was performed for the nominal operation conditions determining the Brayton and combined cycle. Furthermore, steam utilization for the gas turbine propulsion in the Cheng cycle was analysed. In the considered modernization, steam generated in the heat recovery steam generator unit is directed...
-
ENERGY AND EMISSION QUALITY RANKING OF NEWLY PRODUCED LOW-SULPHUR MARINE FUEL
PublikacjaThe article describes the methodology of engine tests on new types of low-sulphur marine fuels in laboratory conditions in order to conduct a comprehensive assessment of their suitability for powering full-size marine engines. The innovativeness of the proposed solution consists of adapting the laboratory Diesel Engine Test Bed to carry out experimental tests using residual and alternative fuels so that it is possible to imitate...
-
ALGORYTMY STEROWANIA SILNIKA WYSOKOPRĘŻNEGO Z UKŁADEM COMMON RAIL
PublikacjaRozwój wiedzy i technologii związanej z procesami spalania paliwa w silniku i prowadzeniem kontrolowanego procesu spalania, skutkuje wzrostem sprawności silników i lepszą ochroną środowiska. Ciekawym rozwiązaniem technicznym jest silnik z zapłonem samoczynnym pracujący z bardzo wysokim ciśnieniem wtrysku paliwa i często z recyrkulacją spalin – silnik z układem Common Rail. Do sterowania silnika stosowane są złożone układy mechatroniczne...
-
Thermodynamic Cycle Concepts for High-Efficiency Power Plans. Part A: Public Power Plants 60+
PublikacjaAn analysis was carried out for different thermodynamic cycles of power plants with air turbines. Variants with regeneration and different cogeneration systems were considered. In the paper, we propose a new modification of a gas turbine cycle with the combustion chamber at the turbine outlet. A special air by-pass system of the combustor was applied and, in this way, the efficiency of the turbine cycle was increased by a few points....
-
TEORIA DECYZYJNYCH PROCESÓW SEMI-MARKOWA I JEJ ZASTOSOWANIE W PROJEKTOWANIU I EKSPLOATACJI OKRĘTOWYCH SILNIKÓW GŁÓWNYCH I INNYCH URZĄDZEŃ SIŁOWNI OKRĘTOWYCH
PublikacjaW referacie zaprezentowano znaczenie teorii procesów semi-Markowa w naukach technicznych, zwłaszcza w teorii niezawodności urządzeń technicznych, teorii bezpieczeństwa ich działania oraz statystycznej teorii podejmowania decyzji eksploatacyjnych. W referacie wyeksponowano także przydatność teorii procesów semi-Markowa w teorii i praktyce eksploatacji wspomnianych urządzeń technicznych na przykładzie tak istotnych urządzeń w transporcie...
-
Risk criteria for sea-going ships arising from the operation of the main engines' crankshaft - conecting rod - piston systems
PublikacjaIn the article the risk criterion for sea-going ships arising from the operation of the main engines' crankshaft - connecting rod - piston systems is proposed. These criterion is based on the procedures recommended in the Formal Safety Assessment method developed under the auspices of International Maritime Organization (IMO). First of all the collective risk criterion for ship has been proposed. In the next step, the share of...
-
Modeling of the internal combustion engine cooling system
PublikacjaThe article concerns computer modelling of processes in cooling systems of internal combustion engines. Modelling objectives and existing commercial programs are presented. It also describes Author’s own method of binding graphs used to describe phenomena in the cooling system of a spark ignition engine. The own model has been verified by tests on the engine dynamometer. An example of using a commercial program for experimental...
-
The conception of energetic investigations of the multisymptom fatigue of the simple mechanical systems' constructional materials
PublikacjaThe article presents the basic assumptions of the research project aimed, as the main scientific purpose, an identification of the slow-changeable energy processes surrounding the high-cycle fatigue of constructional materials within the plain mechanical system, especially the marine one, for diagnostic purposes. There is foreseen an application of alternative diagnostic methods based on energetic observations of the multi-symptom,...
-
Impacts of Using Exhaust Gas Recirculation and Various Amount of Dimethyl Ether Premixed Ratios on Combustion and Emissions on a Dual-Fuel Compression Ignition Engine
PublikacjaIn the presented research, the authors dealt with the specific properties of the combustion process of dimethyl ether (DME) in a combustion car (Volkswagen Golf IV) engine AJM 1.9 TDI PDE made by Volkswagen factory. Dimethyl ether is an alternative fuel produced most often from natural gas, which can be used in compression ignition engines as a single fuel or co-burned with diesel oil. This work describes the impacts of using exhaust...
-
Power augmentation of PGE Gorzow's gas turbine by steam injection - thermodynamic overview
PublikacjaThe impact of steam injection upon a gas turbine and a combined power plant performance has been investigated. This article describes and summarizes possibilities of modification for current gas turbine in PGE Gorzow power plant into the Cheng cycle. Our modification deals with a thermal cycle, in which steam produced in a heat recovery steam generator is injected into the gas turbine's combustion chamber. It has been proved that...
-
Thermodynamic Cycle Concepts for High-Efficiency Power Plants. Part B: Prosumer and Distributed Power Industry
PublikacjaAn analysis was carried out for different thermodynamic cycles of power plants with air turbines. A new modification of a gas turbine cycle with the combustion chamber at the turbine outlet has been described in the paper. A special air by-pass system of the combustor was applied, and in this way, the efficiency of the turbine cycle was increased by a few points. The proposed cycle equipped with an effective heat exchanger could...
-
SELECTED COMBINED POWER SYSTEMS CONSISTED OF SELFIGNITION ENGINE AND STEAM TURBINE
PublikacjaThis paper presents optimization of selected combined diesel engine-steam turbine systems. Two systems: the system combined with waste heat one-pressure boiler only and its version containing additionally low-pressure boiler proper feeding degasifier and the system of two-pressure cycle, were taken into considerations. Their surplus values of power output and efficiency associated with utilization of waste heat contained in piston...
-
A study of a compact high-efficiency zero-emission power plant with oxy-fuel combustion
PublikacjaThis paper discusses the application of global trends in gas cycles technology using oxy-fuel combustion. This is followed by a demonstration of a design solution for a new cycle with two enhanced energy-converting devices, namely a wet combustion chamber and a spray-ejector condenser. The proposed gas and steam cycle unit is contained within a single turbine, whose benefits combine those offered by gas turbines (high inlet temperatures)...
-
Stirling engines powered by renewable energy sources
PublikacjaStirling engine is a device that produces mechanical energy using heat from any source of energy, without the need of combustion of any fuel inside the device. Renewable energy sources, which are mostly low-temperature energy sources, can be used to produce mechanical and electrical energy in Stirling engines. The paper presents an overview of the existing prototype Stirling engines designed for using of low-temperature energy...
-
Comparative study of a combined heat and power plant retrofitted by CO2 capture during the combustion of syngas from sewage sludge gasification versus zero-emission combustion of hydrogen produced using renewables
PublikacjaWith ecological requirements aimed at limiting the production of CO2, it is necessary to produce all, or most of the energy from RES. During the transformation process, ecological and highly efficient combustion power plants will be needed. The classic cycle of combined heat and power (CCGT) with green improvements will continue to be one of the most suitable technologies for this task. This article presents the modernization of...