Wyszukiwarka
Filtry
wszystkich: 395
wybranych: 288
Filtry wybranego katalogu
Wyniki wyszukiwania dla: horizontal flow
-
DETERMINATION OF VERTICAL DISPLACEMENTS IN RELATIVE MONITORING NETWORKS
PublikacjaThe problem of determining displacements of objects is an important and current issue, in particular in terms of operational safety. This is a requirement that covers geodetic, periodic control measurements in order to determine horizontal and vertical displacements. The paper is focused on the analysis of vertical displacements. Geodetic measurements and their interpretation allow to reduce the risk of possible structural catastrophes....
-
Effect of Temperature and Nanoparticle Concentration on Free Convective Heat Transfer of Nanofluids
PublikacjaA theoretical analysis of the influence of temperature and nanoparticle concentration on free convection heat transfer from a horizontal tube immersed in an unbounded nanofluid was presented. The Nusselt (Nu) number and heat transfer coefficient were parameters of the intensity of the convective heat transfer. For free convection, the Nu number was a function of the Rayleigh (Ra) number and Prandtl (Pr) number. The Rayleigh (Ra)...
-
Developing a methodology for model tests of floating platforms in a towing tank of low depth
PublikacjaThe paper presents two ways to mooring model of semi-submersible platform for research in the small depth towing pool. The tested model was made in the likeness of 1:100 Thunder Horse platform moored in the Gulf of Mexico at a depth of 1,920 m. Its mooring system consisted of 16 semi-taut mooring lines (chain-wire-chain) spaced Star-shape and attached at the bottom to the suction piles. The tests were performed in the towing pool...
-
STABILITY ANALYSIS OF A TRUSS WITH SLOPING ELASTIC BRACES
PublikacjaSteel trusses have a much greater strength and stiffness in their plane than out of their plane, and therefore should be braced against lateral deflection and twisting. Such elements like purlins apart from bearing vertical load are part of bracing that stabilize roof trusses against distortional buckling. The stability of trusses with elastic bracing was investigated in an experimental research. Braces situated at some angle measured...
-
Degradation of stiffness of building columns exposed to bending and impact load during ground motions
PublikacjaThe safety of civil engineering structures under external loads, including ground motions, is one of the issues related to the idea of sustainable society. The earthquake-induced soft-storey failure is a typical type of damage observed in buildings due to seismic excitation. The failure of an intermediate soft storey of a structure results in large vertical impact loading acting on the lower floors due to the fall of the upper...
-
New transition curve adapted to railway operational requirements
PublikacjaThe paper points to the limited possibilities of improving the existing situation in the area of transition curves used in geometrical layouts of the railway track. Difficulties in the practical implementation and maintenance of very small horizontal ordinates of the transition curve and the ordinates of the gradient due to cant in the initial section, appearing on smooth transition curves, were indicated. The main reason for this...
-
Simple 2-D Direction-of-Arrival Estimation Using an ESPAR Antenna
PublikacjaIn this letter, it has been shown how an electronically steerable parasitic array radiator (ESPAR) antenna can be used for 2-D direction-of-arrival (DoA) estimation employing received signal strength (RSS) values only. The proposed approach relies on changes in RSS values recorded at the antenna output port observed for different vertical and horizontal directions, while antenna’s main beam sweeps 360° area around the ESPAR antenna. Based...
-
A Deformation Sweep Testing Procedure to Evaluate Damage in Cold Recycled Material Mixtures
PublikacjaThis chapter describes a new testing procedure to assess damage in cold recycled material mixtures. Specifically, stiffness modulus tests were performed at increasing deformation levels, with the objective of creating a gradual increase in damage. The succession of tests with increasing deformation was interspersed with tests at small deformation, with the objective of evaluating the damage gradually inflicted on the specimen....
-
Mobility and bioavailability of mercury in sediments of the southern Baltic sea in relation to the chemical fractions of iron: Spatial and temporal patterns
PublikacjaMarine sediments play a significant role as reservoirs for mercury (Hg), a bioaccumulative toxic pollutant that poses risks to human and ecosystem health. Iron (Fe) has been recognized as an influential factor in the complexation and bioavailability of Hg in sediments. However, limited studies have investigated the interactions between the chemical fractions of these elements in natural settings. This study aims to examine the...
-
Reliable OFDM Data Transmission with Pilot Tones and Error-Correction Coding in Shallow Underwater Acoustic Channel
PublikacjaThe performance of Underwater Acoustic Communication (UAC) systems are strongly related to the specific propagation conditions of the underwater channel. Horizontal, shallow-water channels are characterised by extremely disadvantageous transmission properties, due to strong multipath propagation and refraction phenomena. The paper presents the results of communication tests performed during a shallow, inland-water experiment with...
-
Using FreeFEM open software for modelling the vibrations of piezoelectric devices
PublikacjaModelling vibrations of piezoelectric transducers has been a topic discussed in the literature for many decades. The first models - so-called one-dimensional - describe the vibrations only near operating frequency and near its harmonics. Attempts to introduce two-dimensional models were related to the possibility of one transducer working at several frequencies, including both thickness vibrations and those resulting from the transducer...
-
Effect of excitation intensity on slope stability assessed by a simplified approach
PublikacjaThe paper concerns the selection of a design accelerograms used for the slope stability assessment under earthquake excitation. The aim is to experimentally verify the Arias Intensity as an indicator of the excitation threat to the slope stability. A simple dynamic system consisting of a rigid block on a rigid inclined plane subjected to horizontal excitation is adopted as a slope model. Strong ground motions recorded during earthquakes...
-
Identification of transition curves in vehicular roads and railways
PublikacjaIn the paper attention is focused on the necessity to systematize the procedure for determining the shape of transition curves used in vehicular roads and railway routes. There has been presented a universal method of identifying curvature in transition curves by using differential equations. Curvature equations for such known forms of transition curves as clothoid, quartic parabola, the Bloss curve, cosinusoid and sinusoid, have...
-
THE APPLICATION OF KALMAN FILTERING TO PREDICT VERTICAL RAIL AXIS DISPLACEMENTS OF THE OVERHEAD CRANE BEING A COMPONENT OF SEAPORT TRANSPORT STRUCTURE
PublikacjaAs the devices designed to transport materials, the overhead cranes should meet certain geometric requirements for their operation to be safe. The presently available geodetic equipment, in particular total stations, provides opportunities for precise 3D measurements of coordinates of the controlled points. These coordinates make a basis for correcting the height of crane runway axes. The paper presents a method to calculate position...
-
EFFECT OF NANOFLUID CONCENTRATION ON TWO-PHASE THERMOSYPHON HEAT EXCHANGER PERFORMANCE
PublikacjaAn approach – relaying on application of nanofluid as a working fluid, to improve performance of the two-phase thermosyphon heat exchanger (TPTHEx) has been proposed. The prototype heat exchanger consists of two horizontal cylindrical vessels connected by two risers and a downcomer. Tube bundles placed in the lower and upper cylinders work as an evaporator and a condenser, respectively. Distilled water and nanofluid water-Al2O3...
-
Application of nanofluids in thermal technologies
PublikacjaNanofluids it is a relatively new category of thermal fluids that can serve as coolants, both in single- and two phase systems. However application of nanofluids in industrial applications requires faultless their thermophysical properties. Existing models originally developed for liquid/solid particles mixtures (slurries) fail in case of nanofluids. Moreover correlations used to calcuate heat transfer coefficients of conventional...
-
Studying road restraint systems to develop new guidelines
PublikacjaThe paper will present a proposed approach to such work along with preliminary results of numerical studies for selected problems using road safety devices such as safety barriers on horizontal curves, the effect of kerbs on bridges or the location of obstacles within the barrier’s working width. The paper will discuss assumptions to a methodology of numerical models, calculations and automated processing of data to help with assessing...
-
OPERATING CONDITIONS OF SLIDE BEARINGS OF MILLS USED IN KGHM POLSKA MIEDŹ S.A.
PublikacjaThe paper contains the results from a tec hnical analysis of the conditions of the operation of hydrodynamic bearings supporting the drums of ore processing mills at KGHM Polska Mied ź S.A. A theoretical analysis was performed on the grounds of onsite examination and measurem ents of principal dimensions of the bearings of interest. The computer simulation covered the characteristics of the oil film in the bearings...
-
Shallow-Water Acoustic Communications in Strong Multipath Propagation Conditions
PublikacjaA phenomenon that has a strong impact on signal transmission conditions in Underwater Acoustic Communication (UAC) systems is multipath propagation. As a result of multipath propagation, the transmitted signal undergoes time dispersion which results in inter-symbol interference observed on the receiving side. Time dispersion is large, especially in horizontal channels in shallow waters which significantly limits the transmission...
-
Methodology for Performing Bathymetric Measurements of Shallow Waterbodies Using an UAV, and their Processing Based on the SVR Algorithm
PublikacjaState-of-art methods of bathymetric measurements for shallow waterbodies use Global Navigation Satellite System (GNSS) receiver, bathymetric Light Detection and Ranging (LiDAR) sensor or satellite imagery. Currently, photogrammetric methods with the application of Unmanned Aerial Vehicles (UAV) are gathering great importance. This publication aims to present step-by-step methodology for carrying out the bathymetric measurements...
-
Experimental study on the behaviour of steel columns under seismic-induced axial impact load
PublikacjaIt has been observed during major earthquakes that the so called soft-storey failure of an upper floor of a structure results in large impact load acting on structural members of the lower storeys. It may further lead to progressive collapse of the whole structure substantially intensifying human and material losses. Therefore, the aim of this paper is to investigate experimentally the behaviour of columns under bending (observed...
-
Reprezentation of mechanic hysteresis in a railway track using the Preisach model
PublikacjaThis paper presents an implementation of the classic scalar Preisach model to describe the hysteresis phenomenon created in a railway track subjected to lateral (in the horizontal plane) displacements. The principles of the Preisach theory and the scalar mathematical model of the mechanical hysteresis that is based on statistically distributed modified hysteresis operators are briefly presented. This article presents the characteristic...
-
Pool Boiling of Water–Al2O3 and Water–Cu Nanofluids Outside Porous Coated Tubes
PublikacjaThis paper deals with pool boiling ofwater–Al2O3 and water–Cu nanofluids on porous coated, horizontal tubes. Commercially available stainless-steel tubes having 10 mm outside diameter and 0.6 mm wall thickness were used to fabricate a test heater. Aluminum porous coatings 0.15 mm thick with porosity of about 40% were produced by plasma spraying. A smooth tube served as a reference tube. The experiments were conducted under different...
-
An approach for the response of buildings subjected to impact load after soft-story failure due to earthquake excitation
Publikacjahe soft-story failure is one of the most typical types of damage observed in buildings during earthquakes. The failure of an intermediate soft story of a structure results in large impact loading acting on the lower floors due to the fall of the upper stories. The aim of the present paper is to study the behavior of the structural members exposed to such extreme load conditions occurring under ground motion excitation. Special...
-
Developing Methodology for Model Tests of Floating Platforms in Low -Depth Towing Tank
PublikacjaThe paper presents two different methods of physical modeling of semi-submersible platform mooring system for research in low depth towing tank. The tested model was made in the scale of 1:100 resembling the "Thunder Horse" platform moored in the Gulf of Mexico at a depth of 1,920 m. Its mooring system consisted of 16 semi-taut mooring lines (chain-wire-chain) spaced starshape and attached at the bottom to suction piles. The tests...
-
Numerical study on pounding between two adjacent buildings under earthquake excitation
PublikacjaSeismic excitation, which results in large horizontal relative displacements, may cause collisions between two adjacent structures due to insufficient separation distance between them. Such collisions, known as earthquake-induced structural pounding, may induce severe damages. In this paper, the case of pounding between two adjacent buildings is studied by the application of single degree-of-freedom structural models. Impact is...
-
Results of the application of tropospheric corrections from different troposphere models for precise GPS rapid static positioning
PublikacjaIn many surveying applications, determination of accurate heights is of significant interest. The delay caused by the neutral atmosphere is one of the main factors limiting the accuracy of GPS positioning and affecting mainly the height coordinate component rather than horizontal ones. Estimation of the zenith total delay is a commonly used technique for accounting for the tropospheric delay in static positioning. However, in the...
-
Preparatory Railway Track Geometry Estimation Based on GNSS and IMU Systems
PublikacjaThe article discusses an important issue of railway line construction and maintenance, which fundamentally is the verification of geometric parameters of the railway track. For this purpose, mobile measurements have been performed using a measuring platform with two properly arranged GNSS receivers, which made it possible to determine the base vector of the platform. The measuring functionality of the system was extended by IMU....
-
Analysis of Modal Parameters Using a Statistical Approach for Condition Monitoring of the Wind Turbine Blade
PublikacjaThe primary objective of the presented paper is the numerical and experimental investigation related to developing a useful diagnostic method, which can be used for determining the site and size of damage in laminated shells of wind turbine blades. The described detection technique is based on the analysis of low frequencies bending vibrations mode shapes of rotor blades. The authors used the commonly applied statistics methods...
-
Simple 60 GHz Switched Beam Antenna for 5G Millimeter-Wave Applications
PublikacjaA new 60 GHz band single-input switched beam antenna is proposed for the fifth-generation (5G) millimeter-wave network applications. The presented design is capable of electronically switching the main beam in two different directions via a proposed microstrip-line-to-slotline single-pole dual-throw (SPDT) switch based on commercially available p-i-n diodes. The antenna is fabricated in a low-cost printed circuit board process...
-
Low-Profile Interdigitated UHF RFID Tag Antenna for Metallic Objects
PublikacjaThis article presents a novel miniature interdigitated ultra-high frequency (UHF) radio frequency identification (RFID) tag antenna that can be placed on metallic objects. The tag structure comprises two horizontal strip lines, each loaded with seven identical open stubs, and an integrated circuit (IC) chip connected directly to the feed lines in the middle of the structure. The perfect match to the IC chip’s impedance is realized...
-
Using Minimum Actuators to Control Shape and Stress of a Double Layer Spherical Model Under Gravity and Lateral Loadings
PublikacjaSpherical domes are picturesque structures built in developed countries to attract tourists. Due to horizontal and vertical overloading, the structures’ attractive shapes may be disturbed, and some members' stress may exceed the elastic level. In this paper, the shape and stress of a deformed double-layer spherical numerical model due to simultaneous lateral and vertical loadings are controlled, meanwhile, the number of actuators...
-
Precise Bathymetry as a Step Towards Producing Bathymetric Electronic Navigational Charts for Comparative (Terrain Reference) Navigation
PublikacjaBathymetric Electronic Navigational Charts (bENCs) contain only bathymetry data and can be used in applications such as underwater positioning, dredging and piloting. According to International Hydrographic Organization (IHO) standard S-57, Electronic Navigational Charts (ENCs) contain depth information with pure density of depth contours. Typical depth contours encoded by Hydrographic Offices are limited to 2, 5, 10 and 20 m....
-
Shales Leaching Modelling for Prediction of Flowback Fluid Composition
PublikacjaThe object of the paper is the prediction of flowback fluid composition at a laboratory scale, for which a new approach is described. The authors define leaching as a flowback fluid generation related to the shale processing. In the first step shale rock was characterized using X-ray fluorescence spectroscopy, X-ray diractometry and laboratory analysis. It was proven that shale rock samples taken from the selected sections of horizontal...
-
A Broadband Circularly Polarized Wide-Slot Antenna with a Miniaturized Footprint
PublikacjaThis letter presents a novel and simple feeding technique for exciting orthogonal components in a wide-slot antenna. In this technique, a rectangular bracket-shape parasitic strip is placed at the open end of the straight microstrip line to excite the fundamental horizontal and vertical components of the circular polarization (CP). The proposed technique—when employed in conjunction with the asymmetrical geometry of coplanar waveguide...
-
Behaviour of Colliding Multi-Storey Buildings under Earthquake Excitation Considering Soil-Structure Interaction
PublikacjaThis paper investigates the coupled effect of the supporting soil flexibility and pounding between neighbouring, insufficiently separated buildings under earthquake excitation. Two adjacent three-storey structures, modelled as inelastic lumped mass systems with different structural characteristics, have been considered in the study. The models have been excited using the time history of the Kobe earthquake of 1995. A nonlinear...
-
Orientation-aware ship detection via a rotation feature decoupling supported deep learning approach
PublikacjaShip imaging position plays an important role in visual navigation, and thus significant focuses have been paid to accurately extract ship imaging positions in maritime videos. Previous studies are mainly conducted in the horizontal ship detection manner from maritime image sequences. This can lead to unsatisfied ship detection performance due to that some background pixels maybe wrongly identified as ship contours. To address...
-
A Critical Reanalysis of Uncontrollable Washboarding Phenomenon in Metal Band Sawing
PublikacjaThe article analyzes the cutting process of hard bars. Investigations conducted in industrial conditions demonstrated the presence of surface errors in the machined workpieces in the form of washboard patterns. The purpose of this study was to analyze the results of cutting on band sawing machines with different band saw blades. The cutting processes were conducted on three different horizontal band sawing machine types. Analyzed...
-
Numerical investigation on dynamic response of a steel lattice tower under various seismic events
PublikacjaThe present paper presents the results of the numerical study designed to investigate the soil-structure flexibility effects on modal parameters (i.e. fundamental frequencies) and time-history analysis response (represented by the top relative displacements) of a 46.8 m high steel lattice tower subjected to a number of ground motions including also one mining tremor. In addition to the fixed-base condition, three different soil...
-
Load capacity of steel-aluminium brackets under static and cyclic laboratory tests
PublikacjaThe aim of the research is the laboratory investigation of steel-aluminium brackets employed to fasten lightweight curtain walls to building facilities. Static pressure, suction forces, and cyclic loads parallel to end plates (horizontal – to simulate wind influence) were applied in the study. The steel-aluminium brackets were tested on a reinforced concrete substrate made of C30/37 concrete class to simulate the real working conditions....
-
The shallow sea experiment with usage of linear hydrophone array
PublikacjaPurpose of this article is to present designed and made linear hydrophone array and the results obtained during in situ trails on Gulf of Gdańsk. The measuring system allowed to localize hydrophones in the selected points and perform measurements in both the horizontal antenna positioning and vertical. Made in this way recordings allow creating accurate 3D imaging of sound intensity/propagation. During research three floating objects...
-
Sundials of St Mary’s Church in Gdańsk / Zegary słoneczne kościoła pw. Wniebowzięcia Najświętszej Panny Marii w Gdańsku
PublikacjaThe paper presents contemporary research evidence of form, function and history of the sundials of St Mary’s Church in Gdańsk. The discussed sundials are located on the southern wall of the church transept. The sundial, which is believed to be made by Lorenzo Zachau in 1533, is placed on the west side of the western window, at the edge of the wall. The face of this sundial is separated by a horizontal line into two parts. The upper...
-
Digital Transformation and Its Influence on Sustainable Manufacturing and Business Practices
PublikacjaThe paper focuses on the relationship between businesses and digital transformation, and how digital transformation has changed manufacturing in several ways. Aspects like Cloud Computing, vertical and horizontal integration, data communication, and the internet have contributed to sustainable manufacturing by decentralizing supply chains. In addition, digital transformation inventions such as predictive analysis and big data analytics...
-
Combining Computational Fluid Dynamics with a Biokinetic Model for Predicting Ammonia and Phosphate Behavior in Aeration Tanks
PublikacjaThe aim of this study was to use computational fluid dynamics for predicting the behavior of reactive pollutants (ammonia and phosphate) in the aerobic zone of the bioreactor located at the Wschod wastewater treatment plant in Gdansk, Poland. The one-dimensional advection-dispersion equation was combined with simple biokinetic models incorporating the Monod-type expressions as source terms for the two pollutants. The problem was...
-
The Analysis of Working Parameters Decrease in Photovoltaic Modules as a Result of Dust Deposition
PublikacjaThe aspect of dust accumulation on the surface of photovoltaic (PV) modules should be thoroughly understood in order to minimize possible obstacles affecting energy generation. Several elements affect the amount of pollutant gathered on the surface of a solar device, mainly its localization, which is irreversibly linked to factors such as annual rainfall, occasional snow coverage, or, in a dry climate, increased blow of dust during...
-
Dynamic Bayesian Networks for Symbolic Polyphonic Pitch Modeling
PublikacjaSymbolic pitch modeling is a way of incorporating knowledge about relations between pitches into the process of an- alyzing musical information or signals. In this paper, we propose a family of probabilistic symbolic polyphonic pitch models, which account for both the “horizontal” and the “vertical” pitch struc- ture. These models are formulated as linear or log-linear interpo- lations of up to fi ve sub-models, each of which is...
-
Morphology and internal structure of small-scale washovers formed in the coastal zone of the semi-enclosed tideless basin, Gulf of Gdańsk, Baltic Sea
PublikacjaThis study explores the morphological features and internal structure of small-scale washovers along the southeastern Baltic Sea coast, providing insights into these most widespread yet often neglected deposits in the recent research of geomorphological and sedimentary record of storm surges. A 15-year-long record of morphological changes of the coast was acquired from regional orthophotos to analyse their geometry and spatial...
-
Modeling and Accuracy Assessment of Determining the Coastline Course Using Geodetic, Photogrammetric and Satellite Measurement Methods: Case Study in Gdynia Beach in Poland
PublikacjaThe coastal environment represents a resource from both a natural and economic point of view, but it is subject to continuous transformations due to climate change, human activities, and natural risks. Remote sensing techniques have enormous potential in monitoring coastal areas. However, one of the main tasks is accurately identifying the boundary between waterbodies such as oceans, seas, lakes or rivers, and the land surface....
-
The geodetic monitoring of the engineering structure – a practical solution of the problem in 3D space
PublikacjaThe study raises the issues concerning the automatic system designed for the monitoring of movement of controlled points, located on the roof covering of the Forest Opera in Sopot. It presents the calculation algorithm proposed by authors. It takes into account the specific design and location of the test object. High forest stand makes it difficult to use distant reference points. Hence the reference points used to study the stability...
-
A Compact Circularly Polarized Antenna With Directional Pattern for Wearable Off-Body Communications
PublikacjaThis letter presents a geometrically simple and compact circularly polarized (CP) antenna with unidirectional radiation characteristics for off-body communications. The proposed antenna is based on a microstrip line monopole extension from a coplanar waveguide (CPW) and a protruded stub from one side of the coplanar ground plane along the length of the monopole. The orthogonal components of equal amplitudes required for circular...