Filtry
wszystkich: 1988
wybranych: 1549
-
Katalog
Filtry wybranego katalogu
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: dc corona discharge, ehd flow, flow measurement, pi
-
Analysis of cyclone separator solutions depending on SEC outlet conditions in nCO2PP
PublikacjaUtilization of spray ejector condenser in order to carry out direct-contact condensation of vapour with inert gas (CO2) on a spray of subcooled liquid integrated with separator (to make pure CO2) has been proposed for the task of condensation and CO2 separation in the negative CO2 emission gas power plant. Condensation and separation has a significant impact on the thermodynamic efficiency of the entire negative CO2 emission gas...
-
Rational method of grit chamber efficiency determination
PublikacjaAlthough grot chambers are designed with utmost care, they still remain difficuly to control. As concentration of grit is non-uniform, representative measurements of the sand concentration is a very complex issue. In the paper the results of measure,ents performed at WTP in Gdańsk and Gdynia were analyzed. The proposed method to determine grit chambers efficiency is based on comparison of suspension flow in the inlet and flux of...
-
THERMAL ANALYSIS AND DESIGN OF HYBRID MICROCHANNEL -MICROJET TEST PROBE
PublikacjaAccurate control of cooling parameters is required in ever wider range of technical applications. It is known that reducing the flow hydraulic diameter to an increase in the economy of cooling and improves its quality (Mikielewicz and Muszyński 2009). Present study describes research results related to the design and construction of the test stand for hybrid microjet- microchannel cooling modules study, which may be applied in...
-
Novel methods for diagnosis of pulmonary microangiopathy in diabetes mellitus
PublikacjaLung microangiopathy is a little known negative influence of diabetes mellitus on the functioning of the lungs. In current medical practice lung microangiopathy is diagnosed by comparing two measurements of lung diffusing capacity - one with the subject standing and one with the subject lying. The necessity to take two measurements is inconvenient. In lung microangiopathy we observe a reduction of diffusing capacity, lung flow...
-
Recuperator with microjet technology as a proposal for heat recovery from low-temperature sources
PublikacjaA tendency to increase the importance of so called dispersed generation, based on the local energy sources and the working systems utilizing both the fossil fuels and the renewable energy resources is observed nowadays. Generation of electricity on industrial or domestic scale together with production of heat can be obtained for example through employment of the ORC systems. It is mentioned in the EU directive 2012/27/EU for cogenerative...
-
Impact of Climate Change on Groundwater Resources in a Young Glacial Multi-Aquifer System
PublikacjaThe aim of this study was to evaluate the trends of climate change on the Kashubian Lake District and to determine the impact of expected trends on groundwater resources. The analysis of trends in temperature and precipitation was conducted for the six-decade history of meteorological measurements at the weather station in Koscierzyna. The analysis shows the trend of temperature increase of +0.0182ºC/year. The highest increase...
-
Experimental and comparative study on the two-phase pressure drop of air-water mixture in U-bend and straight pipe annuli
PublikacjaIn this paper, the experimental and theoretical analysis of pressure drop in singlephase and two phase-flow were presented for straight and U-bend smooth tube annulus and tube annulus with wire coil insert. Experiments for various boundary conditions were performed. In case of U-tube and straight tube with and without turbulator, tests were made for the water-water and air-water systems. The study covered a wide measuring range,...
-
ADAPTIVE METHOD FOR THE SOLUTION OF 1D AND 2D ADVECTION-DIFFUSION EQUATIONS USED IN ENVIRONMENTAL ENGINEERING
PublikacjaThe paper concerns the numerical solution of one-dimensional (1D) and two-dimensional (2D) advection-diffusion equations. For the numerical solution of the 1D advection-diffusion equation a method, originally proposed for solution of the 1D pure advection equation, has been developed. A modified equation analysis carried out for the proposed method allowed increasing of the resulting solution accuracy and consequently, to reduce...
-
Impact of Temperature and Nanoparticle Concentration on Turbulent Forced Convective Heat Transfer of Nanofluids
PublikacjaTheoretical analysis of the influence of nanoparticles and temperature on the average Nusselt (Nu) number and the average heat transfer coefficient (HTC) during the turbulent flow of nanofluid in a horizontal, round tube was carried out. The Nu number is a function of the Reynolds (Re) number and the Prandtl (Pr) number, which in turn are functions of the thermophysical properties of the liquid and the flow conditions. On the other...
-
Review of Methods for Diagnosing the Degradation Process in Power Units Cooperating with Renewable Energy Sources Using Artificial Intelligence
PublikacjaThis work is based on a literature review (191). It mainly refers to two diagnostic methods based on artificial intelligence. This review presents new possibilities for using genetic algorithms (GAs) for diagnostic purposes in power plants transitioning to cooperation with renewable energy sources (RESs). The genetic method is rarely used directly in the modeling of thermal-flow analysis. However, this assignment proves that the...
-
Velocity Field Characteristics at the Inlet to a Pipe Culvert
PublikacjaA poorly designed culvert inlet structure causes scouring, which can lead to the collapse of the culvert and significant damage to the neighboring land. A set of laboratory tests was evaluated to examine velocity distribution at the culvert inlet. A three-dimensional acoustic Doppler velocimeterwas used to measure instantaneous flowvelocity upstream of the culvert. The analysis of mean velocities, turbulence strength, and Reynolds...
-
Tesla Friction-Type Micro Turbine For Small-Scale Cogeneration
PublikacjaTesla turbine is rarely used in professional power installations due to its specific work characteristics and relatively low internal efficiency. However, it has some potential to be applied in micro-power plants operating in distributed co-generation systems, also working in an organic Rankine cycle. This paper presents results from numerical calculations of flow in three models of Tesla disk turbines assuming nitrogen as a working...
-
MEMS Technology Evaluation for Submerged Vehicle Navigation
PublikacjaAnalysis of some vital aspects of inertial navigation using MEMS. The paper presents a few aspects of MEMS gyro errors, and their estimation process in the context of INS processing flow. These errors have a serious impact on overall inertial system performance. The results of undertaken researches in that area, and pointing out the main difficulties behind the INS when using a few top MEMS technologies, including sophisticated...
-
Performance Characteristics of a Micro-turbine, International
Publikacja. In the paper a design of a multi-stage micro-turbine with partial admission of all the stages is described in detail and the results of particular experimental investigations and numerical calculations are shown, followed by conclusions. The co-generative micro-power plant with the HFE7100 as a working medium was designed and built for experimental investigations. The values of the main cycle parameters were as follows:- heat...
-
Evaluation of the significance of the effect of the active cross-sectional area of the inlet air channel on the specific enthalpy of the exhaust gas of a diesel engine using statistics F of the Fisher-Snedecor distribution
PublikacjaThis paper presents the application of Fisher-Snedecor distribution F statistics to assess the significance of the influence of changes in the active cross-sectional area of the inlet air channel (Adol) flow in a diesel engine on the observed diagnostic parameter determined on the basis of measurements of the quick changing exhaust gas temperature in the outlet channel, which is the specific enthalpy of the exhaust gas stream within...
-
Performance Characteristics of a Micro-Turbine
PublikacjaIn the paper a design of a multi-stage micro-turbine with partial admission of all the stages is described in detail and the results of particular experimental investigations and numerical calculations are shown, followed by conclusions. The co-generative micro-power plant with the HFE7100 as a working medium was designed and built for experimental investigations. The values of the main cycle parameters were as follows:heat output:...
-
Thermal and technological aspects of double face grinding of Al2O3 ceramic materials
PublikacjaDouble face grinding with planetary kinematics is a process to manufacture workpieces with plan parallel functional surfaces, such as bearing rings or sealing shims. In order to increase the economic efficiency of this process, it has to be advanced permanently. The temperature in the contact zone of most grinding processes has a huge influence on the process efficiency and the workpiece qualities. In contrast to most grinding...
-
Flood Modelling and Risk Analysis of Cinan Feizuo Flood Protection Area, Huaihe River Basin
PublikacjaThis study evaluated multiple aspects of flood risks and effects on the Cinan Feizuo flood protection area in the Huaihe River basin. Flooding remains a leading problem for infrastructure, especially in urban, residential areas of the region. Effective flood modeling for urbanized floodplains is challenging, but MIKE (ID-2D) is paramount for analyzing and quantifying the risk in the vulnerable region. The Saint-Venant equation...
-
Performance of the flat plate solar collector operated with water-Al2O3 nanofluid
PublikacjaThis paper shows the experimental results of the performance a flat plate solar collector with water-Al2O3 nanofluid as a working fluid. The weight fractions of nanoparticles were 0.1%, 0.2% and 0.4%. The volume flow rate of nanofluid varied from 60 l/h to 170 l/h. The results show that application of nanofluids instead of pure water resulted in higher efficiency of the tested flat plate solar collector for given range of thermal...
-
Optymalne ciśnienie kondensacji w odwróconym obiegu Braytona
PublikacjaMotywacją do podjęcia niniejszej pracy jest potrzeba rozwijania obiegów termodynamicznych charakteryzujących się niskoemisyjnością, takich jak podwójny obieg Braytona z zastosowaniem oksyspalania. Celem przeprowadzonej analizy termodynamicznej było znalezienie optymalnego ciśnienia kondensacji w odwróconym obiegu Braytona. W artykule przybliżono również zagadnienie kondensacji oraz przedstawiono wyniki obliczeń numerycznych wykonanych...
-
Numerical Issues and Approximated Models for the Diagnosis of Transmission Pipelines
PublikacjaThe chapter concerns numerical issues encountered when the pipeline flow process is modeled as a discrete-time state-space model. In particular, issues related to computational complexity and computability are discussed, i.e., simulation feasibility which is connected to the notions of singularity and stability of the model. These properties are critical if a diagnostic system is based on a discrete mathematical model of the flow...
-
Heat transfer intensification by enlarged surface roughness in the plate heat exchanger
PublikacjaIn the paper an experimental analysis of passive heat transfer intensification technique employed in the case of the plate heat exchanger is presented. The passive intensification was obtained by a modification of the heat transfer surface. The roughness of surface was increased by a use of glass micro-beads. Single-phase convective heat transfer in the water-water system was studied. The experiment was accomplished in two stages....
-
Experimental ORC micro-power plant for CHP application Part B: Radial and Multi-stage axial turbines
PublikacjaThe co-generative micro-power plant with the HFE7100 applied as a working medium was designed and built for experimental investigations. Special attention is paid to a micro-turbine which was built and tested in two variants: a radial turbine and an axial turbine. A concept of a radial turbine with 2 centripetal and 2 centrifugal stages is shown. This prototype was equipped with an aerostatic gas bearing and, alternatively, with...
-
Use of response surface methodology in characterization of properties of recycled high density polyethylene/ground tire rubber compositions
PublikacjaSearching for newways to utilize rubber and polymerwaste has been the focus of many studies conducted by research centers and companies worldwide. In this study, the influence of extrusion conditions on the properties of thermoplastic compositions containing post-production recycled high density polyethylene (PE-HD) and ground tire rubber (GTR) at 50:50 mass ratiowas examined. Response Surface Methodology (RSM) was used to determine...
-
Enhancement of lift and drag performances of a NACA0012 airfoil by multi-DBD plasma actuator with additional floating interelectrodes
PublikacjaIt is clear that the improvement of aircraft aerodynamic performances is currently and will continue to be a significant area of research for the aeronautical industry. The current study is focused on theenhancement of aerodynamic airfoil performances by using a multi-DBD plasma actuator mounted around the model leading-edge. Experiments have been conducted at the University of Orleans, in the 2 m x 2 m test section of a large...
-
Pathways of Nitrogen Removal in Hybrid Treatment Wetlands
PublikacjaHybrid Treatment Wetlands (HTWs) are composed of two or more filters with different modes of flow, allowing the benefits of both types of bed to be combined, resulting in better effluent quality (nitrogen and organic compounds removal). Such a heterogeneous environment creates possibilities for different mechanisms of nitrogen removal. The objective of the present study was to investigate the removal of nitrogen versus a range...
-
Investigations On Water Circulation in Animal Sea-Water Basins – On the Example of Seals′ Breeding Pools
PublikacjaThis paper presents general comments concerning investigations on water circulation in animal breeding pools containing sea water. As an example are given results of computer simulation of water circulation in seals’ breeding pools situated in Marine Station at Hel, belonging to Oceanographic Institute, Gdansk University. A mathematical model of three main pools was prepared with taking into account their inflow and outflow water...
-
Polymer journal bearings behaviour research under limited lubrication and cooling conditions conducted on high torque test rig
PublikacjaPolymer journal bearings are frequently used as a water-lubricated bearings of small marine units’ propeller shafts . Choice of these bearings is based on their simple construction and relatively low purchase and maintenance costs. Although properly designed and installed water lubricated bearings may well last for over a decade, rapid wear or failure of these bearings can be observed...
-
Process layout planning and optimised product range selection in manufacture of wooden construction sets
PublikacjaThis paper introduces a systematic deterministic framework for planning and the analysis of facility layouts aimed at manufacturing a variety of parts, as components of specific end products. The essence of the proposed approach lies in the decomposition of a traditional job-shop into layout modules of generic material flow patterns, that inherently yields improved efficiency of the entire system. It entails the use of a relevant...
-
Nitric Oxide-Dependent Pathways as Critical Factors in the Consequences and Recovery after Brain Ischemic Hypoxia
PublikacjaBrain ischemia is one of the leading causes of disability and mortality worldwide. Nitric oxide (NO), a molecule that is involved in the regulation of proper blood flow, vasodilation, neuronal and glial activity constitutes the crucial factor that contributes to the development of pathological changes after stroke. One of the early consequences of a sudden interruption in the cerebral blood flow is the massive production of reactive...
-
Model of Nutrient and Pesticide Outflow with Surface Water to Puck Bay (Southern Baltic Sea)
PublikacjaCoastal basins are particularly exposed to the adverse impact of anthropogenic stress. In many places, despite only the seasonal increase in the number of residents, progressive urbanization and associated changes in the catchment characteristics are noticeable. Puck Bay is part of the Gulf of Gdansk and belongs to the Baltic Sea. Although the area of Puck Bay is covered by the Natura 2000 Network, this has not saved it from eutrophication...
-
Effect of Thermal Treatment and Erosion Aggressiveness on Resistance of S235JR Steel to Cavitation and Slurry
PublikacjaS235JR steel is used in many applications, but its resistance to the erosion processes has been poorly studied. To investigate this resistance, cavitation, and slurry erosion tests were conducted. These tests were carried out at different erosion intensities, i.e., different flow rates in the cavitation tunnel with a system of barricades and different rotational speeds in the slurry pot. The steel was tested as-received and after...
-
The thermal effort during marine steam turbine flooding with water
PublikacjaThe work discussed an extreme case of cooling a steam turbine. The ship's steam turbine was used as an example. In marine transport units with low-speed engines dominate, however, there are also units with steam turbines. An example of analysed marine steam turbine is shown in Fig. 1. When considering the issue of cooling steam turbines, it is necessary to estimate the extreme conditions that may occur during operation of the turbine....
-
A hybrid approach to optimization of radial inflow turbine with principal component analysis
PublikacjaEnergy conversion efficiency is one of the most important features of power systems as it greatly influences the economic balance. The efficiency can be increased in many ways. One of them is to optimize individual components of the power plant. In most Organic Rankine Cycle (ORC) systems the power is created in the turbine and these systems can benefit from effective turbine optimization. The paper presents the use of two kinds...
-
SAMPLE-AND-HOLDING METHOD FOR GAS SENSING APPLIED FOR RESISTANCE GAS SENSORS
PublikacjaThe DC resistance of a Taguchi gas sensor is influenced by the ambient gas. To improve the selectivity and sensitivity of a sensor the fluctuation enhanced sensing (FES) was used. The paper proposes a novel methodology of utilizing FES technique that sample composition of an ambient atmosphere and hold it for further processing (sample-and-holding technique). The method uses the heated gas sensor to sample an ambient atmosphere...
-
Diagnostic Models and Estimators for LDI in Transmission Pipelines
PublikacjaThis article considers and compares four analytical models of the pipeline flow process for leak detection and location tasks. The synthesis of these models is briefly outlined. Next, the methodology for generating data and diagnosing pipes is described, as well as experimental settings, assumptions and implemented scenarios. Finally, the quality of model-based diagnostic estimators has been evaluated for their bias, standard deviations...
-
Low energy elastic electron scattering from benzonitrile (C6H5CN)
PublikacjaWe present experimental differential elastic scattering cross sections (DCSs) for low energy electron scattering from benzonitrile along with integral and momentum-transfer cross sections that are determined from these DCSs. The measurements of DCSs are obtained using the relative flow method with helium as the standard gas, in a crossed electron-molecular gas beam arrangement. Our measurements are made at incident electron energies...
-
Celebrating 50 years of SWIMs (Salt Water Intrusion Meetings)
PublikacjaThe Salt Water Intrusion Meetings, or SWIMs, are a series of meetings that focus on seawater intrusion in coastal aquifers and other salinisation processes. 2018 marks the 50th year of the SWIM and the 25th biennial meeting. The SWIM proceedings record half a century of research progress on site characterisation, geophysical and geochemical techniques, variable-density flow, modelling, and water management. The SWIM is positioning...
-
Noise and Electro-Ultrasonic Spectroscopy of Conducting PolymerThick Films
PublikacjaThick conducting films based on conducting polymer are characterized by DC conductivity and noise in temperature range 10 to 300 K. Conducting polymers could be used e.g. for the top electrode (cathode) in the solid tantalum or niobium capacitors. On the conducting polymer layer the top layer of carbon/graphite and/or silver polymer based pastes is applied in the capacitor technology. Our samples structure consists of conducting...
-
Routing decisions independent of queuing delays in broadband leo networks
PublikacjaThis paper presents an analysis of queuing and propagation delays of Inter-Satellite Links (ISLs) in broadband Low-Earth Orbit (LEO) satellite networks. It is shown that queuing delays are negligible in all reasonable working conditions of the broadband ISL network. This fact makes it possible to simplify the routing protocols in such networks and permits using already known multi-commodity flow solutions for routing. The performance...
-
Analysis of the selection of low temperature medium for a turbine power plant using ocean thermal energy (OTEC)
PublikacjaThe paper presents the results and conclusions of numerical calculations modelled in the EES program of a closed OTEC cycle. The following mediums were analysed: ammonia, R32, R41, R404a, R407c, R410a, R423a, R500, R502, R507a and R114, R152a, R234fa, R600, R1234yf, R1234ze. Analogous assumptions were adopted as in the ORC cycle with heat regeneration for dry refrigerants without regeneration for wet refrigerants. Each of them...
-
NEW TRENDS IN DEVELOPMENT OF ORC'S FOR MICROPOWER GENERATION
PublikacjaIn the paper, new trends in development of micropower generation of heat and electricity are presented. New type of CHP for domestic usage is developed in the Institute of Fluid-Flow Machinery PAS and methods of its design are presented. The most promising trends in equipment of ORC cycle for this purpose were discussed. Main attention was focused on micro-heat exchangers design based on micro-channels and micro-jets. In our opinion...
-
THERMODYNAMIC ANALYSIS OF A GENERATION IV SCWR NUCLEAR POWER PLANT CYCLE
PublikacjaThis article presents a flow and thermodynamic analysis of a Generation IV nuclear cycle. An SCWR (Supercritical water reactor) is a high temperature and high pressure reactor that uses water at a temperature above its thermodynamic critical point as the working fluid. The cycle used for the calculations consists of one interstage superheater and 7 regenerative heat exchangers. Division pressure was optimized in view of the cycle efficiency,...
-
Nitrogen dioxide sensing properties of PEDOT polymer films
PublikacjaThis work presents a simple and fully electrochemical route for the polymerization of poly(3,4-ethylenedioxytiophene) (PEDOT) films for fabricating a NO2 gas sensor prepared by electropolymerization of 3,4-Ethylenedioxythiophene (EDOT) monomer in lithium perchlorate/acetonitrile solution. The main aim of this study is to determine the sensing properties of conductive polymer at elevated temperatures. The effects of the humidity,...
-
Capacity analysis of the selected track system in partially ordered space
PublikacjaA proper location of the interval sections has significant impact on the traffic flow in the railway track network. This issue is critical during line modernization as well as when a new solution accounting for the traffic forecast at particular element of the railway track network is developed . However, the situation is more complex and more expensive for railway stations since improvement of the capacity requires critical organizational...
-
Analysis of the selection of low-temperature medium for a turbine power plant using ocean thermal energy (OTEC)
PublikacjaThe paper presents the results and conclusions of numerical calculations modelled in the EES program of a closed OTEC cycle. The following mediums were analysed: ammonia, R32, R41, R404a, R407c, R410a, R423a, R500, R502, R507a and R114, R152a, R234fa, R600, R1234yf, R1234ze. Analogous assumptions were adopted as in the ORC cycle with heat regeneration for dry refrigerants without regeneration for wet refrigerants. Each of them...
-
Indoor accelerated controlled corrosion degradation test of small- and large-scale specimens
PublikacjaThe work presented here is a part of a long-term project analysing the structural behaviour of ageing marine structures. An accelerated corrosion degradation set-up was developed to reproduce corroded marine structural specimens of different degrees of degradation, controlling various natural factors, i.e., temperature, oxygen content, salinity, and flow velocity. The nine stiffened plates of 1.2 m length and 30 small scale specimens...
-
Wybrane zagadnienia przepływowe turbiny gazowej pracującej w tłoczni gazu ziemnego.
PublikacjaW niniejszym artykule przedstawiono cieplno-przepływowe obliczenia turbiny gazowej, stanowiącej napęd sprężarki w tłoczni gazu ziemnego. Wartości parametrów wejściowych niezbędnych do przeprowadzenia obliczeń przyjęto na podstawie danych technicznych tłoczni zasilających polski odcinek gazociągu tranzytowego Jamał-Europa, w których pracują turbiny gazowe SGT-600 firmy Siemens, o mocy 25,3 MW.
-
Evaluating the position of a mobile robot using accelerometer data
PublikacjaThis paper analyses the problem of determining the position of a robot using an accelerometer, which is an essential part of inertial measurement units (IMU). The information gained from such a gauge, however, requires double integration of sensor data. To assure an expected effect, a mathematical model of a low-cost accelerometer of the MEMS type is derived. Moreover, in order to improve the performance of positioning based on...
-
Evaluating the mobile robot positions using accelerometer data
PublikacjaThis paper analyzes the problem of determining the position of a robot using an accelerometer, which is an essential part of inertial measurement units (IMU). The information gained from such a gauge, however, requires double integration of sensor data. To assure an expected effect, a mathematical model of a low-cost accelerometer of the MEMS type is derived. Moreover, in order to improve the performance of positioning based on...