Filtry
wszystkich: 2057
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: SOIL-STEEL BRIDGE
-
Mechanical properties of VL E27 steel for shipbuilding – fracture documentation (test in 0°C)
Dane BadawczeOne of the basic divisions of steels used for ship hulls and ocean engineering structures is the division into: normal strength steels, high strength steels and extra high strength steels. The belonging to the group is determined by the mechanical properties of the steel, such as: yield point, ultimate strength and plastic elongation after fracture....
-
Mechanical properties of VL E27 steel for shipbuilding – fracture documentation (test in -20°C)
Dane BadawczeOne of the basic divisions of steels used for ship hulls and ocean engineering structures is the division into: normal strength steels, high strength steels and extra high strength steels. The belonging to the group is determined by the mechanical properties of the steel, such as: yield point, ultimate strength and plastic elongation after fracture....
-
High-temperature kinetics study of 430L steel powder oxidized in air at 600–850 °C
PublikacjaThe 430L stainless steel powder with a mean particle size of 95 μm was studied to determine its high-temperature oxidation properties. Continuous thermogravimetric measurements were carried out for 100 h in air at temperatures in the range of 600–850 °C. Even though a considerable amount of Cr (up to ˜5 wt.% Cr) inside the grains was depleted – especially inside small grains – no breakaway oxidation was observed. This indicates...
-
Experimental study on models of cylindrical steel tanks under mining tremors and moderate earthquakes
PublikacjaThe aim of the study is to show the results of complex shaking table experimental investigation focused on the response of two models of cylindrical steel tanks under mining tremors and moderate earthquakes, including the aspects of diagnosis of structural damage. Firstly, the impact and the sweep-sine tests have been carried out, so as to determine the dynamic properties of models filled with different levels of liquid. Then,...
-
Application of linear buckling sensitivity analysis to economic design of cylindrical steel silos composed of corrugated sheets and columns
PublikacjaThe paper deals with global stability of steel cylindrical silos composed of corrugated walls and vertical columns with loads imposed by a bulk solid following Eurocode 1. The optimum silo design with respect to the steel weight was based on a sensitivity analysis method. The changes of silo column profiles at each design step were performed by means of influence lines for the buckling load factor due to the unit column bending...
-
Straightening of ship hull structure made of 316L stainless steel - microstructure of naturally colled material
Dane BadawczeThe AISI 316L type steel belongs to the group of chromium-nickel stainless steels. They are determined according to European standards as X2CrNiMo17-12-2 and belong to the group of austenitic stainless steels. Steels of this group are used for elements working in seawater environments, for installations in the chemical, paper, and food, industries,...
-
Straightening of ship hull structure made of 316L stainless steel - microstructure of water cooled material
Dane BadawczeThe AISI 316L type steel belongs to the group of chromium-nickel stainless steels. They are determined according to European standards as X2CrNiMo17-12-2 and belong to the group of austenitic stainless steels. Steels of this group are used for elements working in seawater environments, for installations in the chemical, paper, and food, industries,...
-
Quasistatic and fatigue behavior of an AISI H13 steel obtained by additive manufacturing and conventional method
PublikacjaThis work aims to compare the mechanical behavior of an AISI H13 steel obtained by additive manufacturing with that obtained by conventional manufacturing methods. The average values of the ultimate tensile strength (UTS) and ductility obtained for the specimens produced by the conventional method were equal to 658 MPa and 18%, respectively, which compares with 503 MPa and 0.75% registered for the selective laser melting (SLM)...
-
Influence of fasteners and connections flexibility on deflections of steel building including the stressed skin effect
PublikacjaThe paper presents the analysis of the influence of fasteners and connections flexibility on displacements of symmetrical single-bay pitched-roof steel building, including trapezoidal cladding acting as a diaphragm. The purpose of the article was to compare numerical models with and without taking into consideration fasteners and connections flexibility in order to observe the differences in transverse stiffness of the building...
-
Effect of Pin Shape on Thermal History of Aluminum-Steel Friction Stir Welded Joint: Computational Fluid Dynamic Modeling and Validation
PublikacjaThis article studied the effects of pin angle on heat generation and temperature distribution during friction stir welding (FSW) of AA1100 aluminum alloy and St-14 low carbon steel. A validated computational fluid dynamics (CFD) model was implemented to simulate the FSW process. Scanning electron microscopy (SEM) was employed in order to investigate internal materials’ flow. Simulation results revealed that the mechanical work...
-
Storage of High-Strength Steel Flux-Cored Welding Wires in Urbanized Areas
PublikacjaThe condition of the consumables is a key factor determining the waste reduction in the welding processes and the quality of the welded joint. The paper presents the results of tests of four types of fux-cored wires dedicated for welding high-strength steels, stored for 1 month and 6 months in Poland in two urbanized areas: in a large seaside city (Gdańsk) and in Warsaw, located in the center of the country. The wires were subjected...
-
Study of microstress state of P91 steel using complementary mechanical Barkhausen, magnetoacoustic emission, and X-ray diffraction techniques
PublikacjaThe paper deals with assessment of microstress state of martensite P91 steel using three complementary techniques: mechanical Barkhausen emission, magnetoacoustic emission (MAE), and X-ray diffraction (XRD) profile analysis. Magnetic coercivity Hc and microstructure were investigated with inductive magnetometry and magnetic force microscopy (MFM), respectively. Internal stress level of P91 steel was modified by heat treatment....
-
Mechanical properties of VL E27 steel for shipbuilding – fracture toughness test in 0°C
Dane BadawczeOne of the basic divisions of steels used for ship hulls and ocean engineering structures is the division into: normal strength steels, high strength steels and extra high strength steels. The belonging to the group is determined by the mechanical properties of the steel, such as: yield point, ultimate strength and plastic elongation after fracture....
-
Mechanical properties of VL E27 steel for shipbuilding – fracture toughness test in 20°C
Dane BadawczeOne of the basic divisions of steels used for ship hulls and ocean engineering structures is the division into: normal strength steels, high strength steels and extra high strength steels. The belonging to the group is determined by the mechanical properties of the steel, such as: yield point, ultimate strength and plastic elongation after fracture....
-
Mechanical properties of VL E27 steel for shipbuilding – fracture toughness test in -20°C
Dane BadawczeOne of the basic divisions of steels used for ship hulls and ocean engineering structures is the division into: normal strength steels, high strength steels and extra high strength steels. The belonging to the group is determined by the mechanical properties of the steel, such as: yield point, ultimate strength and plastic elongation after fracture....
-
The influence of the welding environment on the properties of Tekken joints made from S355J2C+N steel
PublikacjaThere are three main methods of underwater welding: dry, wet and intermediate between them, by using the local dry chamber. Due to low costs, the most common method is the wet welding with the use of covered electrodes. Water as a welding environment carries out a lot of problems. The first is limited visibility and instability of the welding arc. The biggest problem during underwater welding is high susceptibility to cold cracking,...
-
API 5L X65 steel - tensile properties in room temperature -10°C, along rolling direction
Dane BadawczeSteel designated as API 5L X65 is often used for oil and gas transportation pipelines. It is caused due to its high ductility, weldability and good corrosion resistance. API 5L X65 is a low alloy steel with carbon content less than 0.3% (depends on delivery condition). Once installed, a pipeline remains in place for many years. Throughout its life,...
-
API 5L X65 steel - tensile properties in room temperature +20°C, across rolling direction
Dane BadawczeSteel designated as API 5L X65 is often used for oil and gas transportation pipelines. It is caused due to its high ductility, weldability and good corrosion resistance. API 5L X65 is a low alloy steel with carbon content less than 0.3% (depends on delivery condition). Once installed, a pipeline remains in place for many years. Throughout its life,...
-
API 5L X65 steel - tensile properties in room temperature -10°C, across rolling direction
Dane BadawczeSteel designated as API 5L X65 is often used for oil and gas transportation pipelines. It is caused due to its high ductility, weldability and good corrosion resistance. API 5L X65 is a low alloy steel with carbon content less than 0.3% (depends on delivery condition). Once installed, a pipeline remains in place for many years. Throughout its life,...
-
API 5L X65 steel - tensile properties in room temperature +20°C, along rolling direction
Dane BadawczeSteel designated as API 5L X65 is often used for oil and gas transportation pipelines. It is caused due to its high ductility, weldability and good corrosion resistance. API 5L X65 is a low alloy steel with carbon content less than 0.3% (depends on delivery condition). Once installed, a pipeline remains in place for many years. Throughout its life,...
-
Physicochemical properties of Mn1.45Co1.45Cu0.1O4 spinel coating deposited on the Crofer 22 H ferritic steel and exposed to high-temperature oxidation under thermal cycling conditions
PublikacjaThe Crofer 22 H ferritic steel substrate was coated with an Mn1.45Co1.45Cu0.1O4 spinel by means of electrophoresis. After high-temperature oxidation under thermal cycling conditions, the physicochemical properties of the obtained system were evaluated. During 48-h cycles that involved heating the samples up to temperatures of either 750 or 800 °C, the oxidation kinetics of both coated and unmodified steel approximately obeyed...
-
AFM analysis of duplex steel structure and composition
Dane BadawczeDue to the high content of alloying elements, duplex stainless steels are characterized by a complex structure of phase transitions. Among all types of intermetallic compounds, the sigma phase is of major interest due to its detrimental effect on both mechanical properties and corrosion behavior. It is an intermetallic phase enriched in Cr and Mo and...
-
CLEAN-SOIL AIR WATER
Czasopisma -
Studies on removal of hydrophobic organics from contaminated soil by washing process
PublikacjaZbadano efektywność wymywania NAPL ze złoża piaskowego za pomocą roztworów dwóch niejonowych surfaktantów: polioksyetylenowanego alkoholu tłuszczowego (Rokanol NL6) oraz alkiloglukozydu (Triton BG10). Jako NAPL zastosowano dwa węglowodory - dodekan i heksadekan. Oba surfaktanty były relatywnie efektywne w usuwaniu dodekanu. Ze wzrostem stężenia surfaktantu obserwowano wzrost efektywności wymywania dodekanu, jednakże Rokanol NL6...
-
Influence of instalation of piles with partial and full displacement of the soil on the subsoil strength
PublikacjaZjawiska zachodzące w bezpośrednim sąsiedztwie pobocznicy pali przemieszczeniowych mają ważne znaczenie dla ich pracy w podłożu. Zmiany stanu naprężenia pionowego, poziomego, zmiana struktury gruntu, wilgotności i zagęszczenia stwarza nowe warunki oddziaływania w strefie pobocznica - podłoże. Przedstawiono wyniki badań sondą CPT w sąsiedztwie pali CFA dla gruntów uwarstwionych, niespoiste / spoiste. Zwrócono uwagę na dobór parametrów...
-
Mercury fractionation in soil and sediment samples using thermo-desorption method
Publikacja -
Effect of pesticides on microorganisms, enzymatic activity and plant in biochar-amended soil
Publikacja -
The impact of gasification wastewater on soil microorganisms and the growth of oat and red clover
Publikacja -
Development of an Autochthonous Microbial Consortium for Enhanced Bioremediation of PAH-Contaminated Soil
Publikacja -
Modified and pristine biochars for remediation of chromium contamination in soil and aquatic systems
Publikacja -
Accelerated solvent extraction-gas chromatographic determination of acidic herbicides in soil
PublikacjaPrzyspieszona ekstrakcja rozpuszczalnikiem z wykorzystaniem wody jako ekstraktanta okazała się skutecznym sposobem izolacji herbicydów kwasowych (MCPP, MCPA, 2,4-D, 2,4,5-T, PCP, dinoseb, dinoterb) z próbek gleby. Wysoka zawartość substancji iłowych powodowała problemy techniczne, które udało się pokonać poprzez zwiększenie stosunku piasku do gleby w celce ekstrakcyjnej. Anality przenoszono z ekstraktu wodnego do rozpuszczalnika...
-
Influence of initial density of cohesionless soil on evolution of passive earth pressure
PublikacjaArtykuł porusza problem odporu bezkohezyjnego gruntu. Obliczenia wykonano wykorzystując metodę elementów skończonych na bazie mikropolarnego prawa hipolastycznego. W obliczeniach przyjęto różne początkowe zagęszczenia oraz średnice cząstek gruntu.
-
Remediation techniques for elimination of heavy metal pollutants from soil: A review
Publikacja -
Scenarios of mercury emission to air, water and soil in Poland to year 2020
Publikacja -
Current methods and technologies for degradation of atrazine in contaminated soil and water: A review
Publikacja -
Numerical simulation of screw displacement pile interaction with non-cohesive soil
PublikacjaA trial numerical simulation of screw displacement pile interaction with non-cohesive subsoil during the transfer of compression load. The simulation was carried out in an axisymmetric system. The technological phases of pile installation in the ground were numerically modelled using equivalent processes which provided similar effects to real technical actions. The results of the numerical calculations were verified by comparing...
-
Wzmacnianie i uszczelnianie gruntu metodą mieszania in situ (Soil Mixing).
PublikacjaAktualny stan rozwoju różnych metod mieszania gruntu, łącznie z charakterystyką używanych maszyn i stosowanego wykonawstwa oraz podsumowaniem doświadczeń. Główne obszary zastosowania oraz podejście projektowe. Aplikacje związane z posadowieniem obiektów drogowych i budowlanych oraz uszczelnianiem gruntu Wybrane przykłady realizacji.
-
Extraction of acidic herbicides from soil by means of accelerated solvent extraction.
PublikacjaZaprezentowano opracowanie procedury izolacji herbicydów kwasowych z gleby z zastosowaniem urządzenia DIONEX ASE 200. Celem było zoptymalizowanie warunków pracy urządzenia: czasu, temperatury, ciśnienia oraz ilości cykli ekstrakcji. Ostatecznie ekstrakty, po przeprowadzeniu analitów w pochodne metylowe, poddano analizie chromatograficznej (GC).
-
Chapter 18. Emulsifying properties of nonionic surfactants in the context of soil remediation
PublikacjaPowstające podczas remediacji gruntów emulsje są niekorzystne, gdyż mogą prowadzić do zatykania porów i unieruchomienia strumienia cieczy przemywającej. Czyni to proces przemywania nieefektywnym. Zbadano stabilność emulsji trzech olejów mineralnych i jednego syntetycznego (PAO 6). W badaniach wykorzystano aparat Turbiscan TLab Expert. Stabilność emulsji określono jako zależność delty transmisji od czasu. Spośród przebadanych emulsji...
-
Chained machine learning model for predicting load capacity and ductility of steel fiber–reinforced concrete beams
PublikacjaOne of the main issues associated with steel fiber–reinforced concrete (SFRC) beams is the ability to anticipate their flexural response. With a comprehensive grid search, several stacked models (i.e., chained, parallel) consisting of various machine learning (ML) algorithms and artificial neural networks (ANNs) were developed to predict the flexural response of SFRC beams. The flexural performance of SFRC beams under bending was...
-
COMMUNICATIONS IN SOIL SCIENCE AND PLANT ANALYSIS
Czasopisma -
International Soil and Water Conservation Research
Czasopisma -
Journal of Chinese Soil and Water Conservation
Czasopisma -
South African Journal of Plant and Soil
Czasopisma -
Journal of the Indian Society of Soil Science
Czasopisma -
JOURNAL OF PLANT NUTRITION AND SOIL SCIENCE
Czasopisma -
SOIL SCIENCE SOCIETY OF AMERICA JOURNAL
Czasopisma -
Effect of Some Sulphur Additives on The Degradation of 9Cr-1Mo Steel After Its 10 Years Service in The CCR Platforming Unit
PublikacjaThe work shows the results of the tests of 9Cr-1Mo steel, which was for 10 years operated in the CCR platforming unit in Group Lotos SA in Gdańsk, and then in the laboratory was sulphidised during 166 h at a temperature of 600 °C. Sulphidation was performed in a mixture of H2-H2S gases at the vapour pressure of sulphur 4.1·10-14 atm, so the order of magnitude of vapour pressure was less than that of the dissociation pressure of...
-
Multivariate analysis of impedance data obtained for coating systems of varying thickness applied on steel
PublikacjaElectrochemical impedance spectroscopy (EIS) has proven to be a valuable test method for the electrochemical characterization of protective coatings on metals. The common way of analysis in impedance spectroscopy is to model the impedance spectrum by means of an equivalent circuit and to extract the quantity of interest using optimization techniques. A model, corresponding to the behavior of the sample under testing, is important...
-
Numerical modelling and analysis of steel specimens subjected to marine immersed corrosion and tensile load
PublikacjaThe present study develops numerical models to analyse the behaviour of steel specimens subjected to marine immersed corrosion degradation and tensile load. The finite element method with the use of the explicit dynamic solver LS-DYNA, satisfying the quasi-static conditions, is employed. Two numerical models are developed, where in the first one, the scans of surfaces gathered from corroded plate specimens are implemented directly...