Filtry
wszystkich: 867
-
Katalog
Wyniki wyszukiwania dla: U-TUBE STEAM GENERATOR
-
Metal (Mo, W, Ti) Carbide Catalysts: Synthesis and Application as Alternative Catalysts for Dry Reforming of Hydrocarbons—A Review
PublikacjaDry reforming of hydrocarbons (DRH) is a pro-environmental method for syngas production. It owes its pro-environmental character to the use of carbon dioxide, which is one of the main greenhouse gases. Currently used nickel catalysts on oxide supports suffer from rapid deactivation due to sintering of active metal particles or the deposition of carbon deposits blocking the flow of gases through the reaction tube. In this view,...
-
Experimental Investigation of Free Convection Heat Transfer from Horizontal Cylinder to Nanofluids
PublikacjaThe results of free convection heat transfer investigation from a horizontal, uniformly heated tube immersed in a nanofluid are presented. Experiments were performed with five base fluids, i.e., ethylene glycol (EG), distilled water (W) and the mixtures of EG and water with the ratios of 60/40, 50/50, 40/60 by volume, so the Rayleigh (Ra) number range was 3 104 Ra 1.3 106 and the Prandtl (Pr) number varied from 4.4 to 176....
-
The voltage on bus bars of the main switchboard of the ro-ro ship electrical power system during maneuvering
Dane BadawczeThe dataset is part of the research results on the quality of supply voltage on bus bars of the main switchboard of the ship's electrical power system in different states of ship exploitation. The attached dataset contains the measurement results carried out onboard a ro-ro ship during maneuvering.
-
WSPÓŁPRACA BLOKU GAZOWO-PAROWEGO Z OBIEGIEM ORC = Combinded power plant in cooperation with ORC
PublikacjaIn the paper presented is the idea of a combined gas and steam power plant cooperation with a low temperature organic Rankine cycle ORC unit. Considerations presented in the paper are accomplished for the Gorzów CHP. The intention of present analysis is heat recovery of low temperature energy and its further use in ORC cycle in order to produce electricity, without increase in fuel consumption. Waste energy is recovered from the...
-
Increase of power and efficiency of the 900 MW supercritical power plant through incorporation of the ORC
PublikacjaThe objective of the paper is to analyse thermodynamical and operational parameters of the supercritical power plant with reference conditions as well as following the introduction of the hybrid system incorporating ORC. In ORC the upper heat source is a stream of hot water from the system of heat recovery having temperature of 90 °C, which is additionally aided by heat from the bleeds of the steam turbine. Thermodynamical analysis...
-
The dynamic performance analysis of the Micro-turbine's rotor supparted on slide and roling element bearings
PublikacjaThis article presents the results of investigations of dynamic characteristics of a small-dimension rotor with slide and rolling element bearings. The object of investigations was the rotor-bearing system designed for the ORC based low-power steam micro-turbine. The investigations were performed using MESWIR series programs, as well as commercial FEA software ABAQUS and MADYN 2000. The results of modal analysis of the micro-rotor...
-
Analysis of diagnostic informativeness of the exhaust temperature of a naval gas turbine
PublikacjaThe conducted investigations aimed to carry out an analysis of the possibility that the failures identification in the automatic control system of a gas turbine engine could be worked out on the basis of measurements of the exhaust stream temperature behind the gas generator. The exhaust temperature represents a basic control parameter, enabling technical state evaluation of the engine within the operation process, which is observed...
-
Ethylene decomposition on TiO2 under UV
Dane BadawczeData contain chromatograms recorded during decomposition of ethylene over TiO2 in a flow reactor under UV irradiation. Semilac UV lamp with total power of 72 W was used as a source of UV light. Chromatograms were recorded in Trace GC Ultra chromatograph equipped in FID detector. Sampling was realised via the dosing sample loop. TiO2 was coated on the...
-
Development of a spray-ejector condenser for the use in a negative CO2 emission gas power plant
PublikacjaOne promising solution for developing low-emission power technologies is using gaseous fuel combustion in pure oxygen when the exhaust gas mixture is composed of H2O and CO2, and where CO2 is separated after steam condensation. The paper presents the results of computational analyses providing to the Spray-Ejector Condenser (SEC) development, which is one of the crucial components of the negative CO2 gas power plant (nCO2PP) cycle...
-
Analytical and reliability data from the real-time simulator biogas plant
Dane BadawczeThe dataset represents the results of biogas plant simulation. The described plant is an agricultural biogas system, which can produce electrical energy with power estimated up to 1070 kW and heat energy that can reach 1200 kW simultaneously.
-
Sound Field Intensity Measurements and Visualization around the Human Head Model . Rozkłąd natężenia pola akustycznego w komorze bezechowej obecności sztucznej głowy i w przypadku braku jej obecności
PublikacjaThe main goal of this research study was to measure and visualize sound field intensity distribution in and without presence of the human head model. Measurements were performed in the anechoic chamber with the 5 cm grid. Experimental setup consisted of a multitone generator, two loudspeakers, human head model, intensimetric probe, the Cartesian robot applied for precise positioning of the acoustic sensor, and an analyzer. Based...
-
Piezo 2011, Electroceramics for End-Users VI
PublikacjaThis work extends a power harvesting with using piezoelectric materials. Experimental presents the development of a piezoelectric MEMS generator which has the ability to scavenge mechanical energy of ambient vibrations from their surroundings and transform it into electrical energy that can be used in energy storage applications. Recent literature shows that piezoelectric transduction has received the most attention for vibration-to-electricity...
-
BLDFIG Projekt i realizacja budowy wysokosprawnościowej turbiny wiatrowej w oparciu o wolnoobrotowy bezprzekładniowy, wielofazowy dwustronnie zasilany generator indukcyjny
ProjektyProjekt realizowany w Katedra Energoelektroniki i Maszyn Elektrycznych zgodnie z porozumieniem LIDER13/0153/2022 z dnia 2023-03-24
-
Thermodynamic analysis of the double Brayton cycle with the use of oxy combustion and capture of CO2
PublikacjaIn this paper, thermodynamic analysis of a proposed innovative double Brayton cycle with the use of oxy combustion and capture of CO2, is presented. For that purpose, the computation flow mechanics (CFM) approach has been developed. The double Brayton cycle (DBC) consists of primary Brayton and secondary inverse Brayton cycle. Inversion means that the role of the compressor and the gas turbine is changed and firstly we have expansion...
-
Experimental investigation of domestic gas boiler fitted with ORC module
PublikacjaIn the paper the prototype of innovative domestic cogenerative ORC system, consisting of a conventional gas boiler and a small size axial vapour microturbines (in-house designed for ORC and the commercially available for Rankine cycle (RC)), evaporator and condenser were scrutinised. In the course of study the fluid working temperatures, rates of heat, electricity generation and efficiency of the whole system were obtained. The...
-
Investigation of the thermal effects in water-lubricated journal bearings with axial grooves
PublikacjaWater-lubricated hydrodynamic journal bearings are frequently applied as stern tube bearings due to their advantages over other bearing types. They are environmentally friendly, can operate without sealings and in conditions of low friction losses. The most popular are bearings with open axial grooves, which require, for proper operation, forced axial flow of the lubricating water. Correctly designed and operated stern tube bearings...
-
OVARY, Ovary - Female, 35 - Tissue image [222063001495731]
Dane BadawczeThis is the histopathological image of OVARY tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.
-
OVARY, Ovary - Female, 35 - Tissue image [2220630014952251]
Dane BadawczeThis is the histopathological image of OVARY tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.
-
OVARY, Ovary - Female, 35 - Tissue image [2220630014959561]
Dane BadawczeThis is the histopathological image of OVARY tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.
-
OVARY, Ovary - Female, 35 - Tissue image [2220630014958491]
Dane BadawczeThis is the histopathological image of OVARY tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.
-
OVARY, Ovary - Female, 35 - Tissue image [2220630014954521]
Dane BadawczeThis is the histopathological image of OVARY tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.
-
Wytwarzanie energii elektrycznej - diagnoza i terapia
PublikacjaW artykule przeanalizowano stan i dalszy rozwój krajowego sektora wytwarzania energii elektrycznej w świetle najnowszych raportów Międzynarodowej Agencji Energetycznej, wskazujących potencjalne trendy i perspektywy w światowej energetyce. Na tle przewidywanego wzrostu zapotrzebowania na energię elektryczną wskazano na możliwość istotnego ograniczenia emisji CO2 drogą zastąpienia przestarzałych, nieefektywnych...
-
Facile synthesis and characterization of graphene and N-doped graphene by CVD method from liquid precursors for promising electrode materials
PublikacjaIn this study, high-quality and few-layered graphene was synthesized using the chemical vapor deposition (CVD) method from liquid sources. Two different liquid carbon sources, pyridine, and benzene, were used and deposited on nickel foam under heat conditions using a bubbler in a quartz tube. X-ray diffraction (XRD) and Raman analysis confirmed the crystalline properties of graphene and N-doped graphene, demonstrating the high...
-
Evaluation of reformer tubes degradation after long term operation
PublikacjaPurpose of this paper is to show the effect of long-term service at elevated temperatures on microstructural changes of cast steel reformer tubes made of the alloy IN-519 (24%Cr, 24%Ni, Nb). The relationship between mechanical properties and microstructure degradation is discussed. Investigations were performed on five tubes taken from ammonia reformer furnace. Tubes worked at temperature of 880C and 3,2 MPa pressure. The operation...
-
Numerical Modelling of Forced Convection of Nanofluids in Smooth, Round Tubes: A Review
PublikacjaA comprehensive review of published works dealing with numerical modelling of forced convection heat transfer and hydrodynamics of nanofluids is presented. Due to the extensive literature, the review is limited to straight, smooth, circular tubes, as this is the basic geometry in shell-and-tube exchangers. Works on numerical modelling of forced convection in tubes are presented chronologically in the first part of the article....
-
Effect of Temperature and Nanoparticle Concentration on Free Convective Heat Transfer of Nanofluids
PublikacjaA theoretical analysis of the influence of temperature and nanoparticle concentration on free convection heat transfer from a horizontal tube immersed in an unbounded nanofluid was presented. The Nusselt (Nu) number and heat transfer coefficient were parameters of the intensity of the convective heat transfer. For free convection, the Nu number was a function of the Rayleigh (Ra) number and Prandtl (Pr) number. The Rayleigh (Ra)...
-
Laser patterned platform with PEDOT–graphene composite film for NO2 sensing
PublikacjaThis work presents a simple and fully electrochemical route used for fabricating of a NO2 gas sensor made of reduced-graphene-oxide-poly(3,4-ethylenedioxythiophene) composite film. The sensing platform was fabricated from alumina substrate and equipped with gold interdigitated electrodes and built-in heater.The temperature distribution on the surface of interdigitated electrodes was investigated by a thermalimaging camera and compared...
-
Problemy dostosowana układu sterowania maszyną dwustronnie zasilaną do nowych wymagań.
PublikacjaW artykule zaprezentowano problemy związane z dostosowaniem układu sterowania maszyną dwustronnie zasilaną pracującą jako generator w elektrowni wiatrowej do nowych wymagań i przepisów stawianych przez operatorów sieci energetycznych. Poruszono problem utrzymania elektrowni wiatrowej w systemie w momencie krótkotrwałego obniżenia lub uskoku napięcia sieci energetycznej spowodowanego odległym zwarciem w systemie lub podłączeniem...
-
Pitch shifter with complex instantaneous frequency rescaling and direct digital synthesis
PublikacjaW artykule zaprezentowano nowy przesuwnik wysokości dźwięku ze skalowaniem częstotliwości chwilowej i z syntezą bezpośrednią. Jest on przeznaczony do komponowania melodii np. w telefonie komórkowym. Implementacja przesuwnika jest oparta na twierdzeniu Bedrosiana, zastosowanego do zespolonego odpowiednika hilbertowskiego przetwarzanego sygnału rzeczywistego. Filtr Hilberta pełni tu też dodatkową rolę. Jest nią filtracja antyaliasingowa....
-
Analysis of Measurement Errors in Rail Vehicles’ Pantograph Inspection System
PublikacjaThe paper presents an approach to evaluation of height measurement errors in laser scanning inspection system. The system, consisting of a laser line generator and a specialized camera, is dedicated to diagnosing carbon contact strips of railway vehicles’ pantographs. While height measurement resolution is easily computable based on system parameters, determining the measurement error is troublesome due to numerous impacts. As...
-
Activated Carbon Produced by Pyrolysis of Waste Wood and Straw for PotentialWastewater Adsorption
PublikacjaPyrolysis of straw pellets and wood strips was performed in a fixed bed reactor. The chars, solid products of thermal degradation, were used as potential materials for activated carbon production. Chemical and physical activation processes were used to compare properties of the products. The chemical activation agent KOH was chosen and the physical activation was conducted with steam and carbon dioxide as oxidising gases. The eect...
-
OVARY, Ovary - Female, 62 - Tissue image [3220630024678001]
Dane BadawczeThis is the histopathological image of OVARY tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.
-
Model neuronowy jako alternatywa dla numerycznego modelu okołodźwiękowego przepływu pary przez palisadę turbinową.
PublikacjaWystępowanie skośnej fali uderzeniowej w przepływie pary przez palisadę turbinową stanowi zagrożenie dla bezpiecznej pracy turbiny oraz dla jej elementów konstrukcyjnych. Detekcja oraz lokalizacja fali uderzeniowej, a także rozpoznanie przyczyny jej powstawania, nie są możliwe do osiągnięcia na drodze pomiarowej. Analizę zjawisk zachodzących wewnątrz kanału przepływowego umożliwiają natomiast modele numeryczne oraz neuronowe. Zaletą...
-
Measurements of passive components using of an IEEE 1149.4 mixed-signal test bus
PublikacjaW pracy przedstawiono wyniki badań nad wykorzystaniem magistrali testującej mieszanej sygnałowo IEEE 1149.4 do pomiarów elementów pasywnych zamontowanych na pakietach elektronicznych. Do badań użyto wyposażonych w magistralę układów scalonych typu STA400. Zaprezentowano metody pomiaru rezystancji pojedynczych elementów z wykorzystaniem źródła prądowego oraz źródła VH znajdującego się w analogowych modułach ABM układu STA400. Pokazano...
-
Exhaust gas temperature measurements in diagnostic examination of naval gas turbine engines. Part I: Steady-state processes
PublikacjaThe article presents a possible method of detecting failures in the flow section and supply system of a naval gas turbine engine based on the exhaust gas temperature measured behind the gas generator. This temperature is a basic diagnostic parameter use for evaluating the technical state of the turbine engine in operation, and is monitored during engine start-ups, accelerations and decelerations of rotor units, and steady-load...
-
Efficient FPGA Implementation of an RFIR Filter Using the APC–OMS Technique with WTM for High-Throughput Signal Processing
PublikacjaNowadays, Finite Impulse Response (FIR) filters are used to change the attributes of a signal in the time or frequency domain. Among FIR filters, a reconfigurable filter has the advantage of changing the coefficient in real-time, while performing the operation. In this paper, the Anti-Symmetric Product Coding (APC) and Odd Multiple Storage (OMS) modules are utilized to implement the reconfigurable FIR filter (RFIR–APC–OMS). Herein,...
-
Quantum security and theory of decoherence
PublikacjaWe sketch a relation between two crucial, yet independent, fields in quantum information research, viz. quantum decoherence and quantum cryptography. We investigate here how the standard cryptographic assumption of shielded laboratory, stating that data generated by a secure quantum device remain private unless explicitly published, is disturbed by the einselection mechanism of quantum Darwinism explaining the measurement process...
-
A commercial gas boiler fitted with the ORC module as perspective solution for households
PublikacjaIn this paper the applicability of the commercial gas boiler (De Dietrich DTG X23N) coupled with the laboratory prototype micro ORC setup was experimentally studied. The main objective was to determine the working fluid capability to obtain required temperatures of vapour prior to the turbine, attainable heat rates and efficiencies of the whole system. The boiler thermal power was 25 kW. Tests were carried out with a single stage...
-
Three phase transient model of wet coal pyrolysis
PublikacjaA one-dimensional transient mathematical model was developed to describe the thermal and flow phenomena during coal pyrolysis in a coke oven. The model was solved numerically using partly implicit methods for gas flow and heat transfer problems. It was successfully validated with industrial-scale measurements of temperature change in the middle-plane of the coke oven chamber. The evolution of temperature and pressure, distributions...
-
Management of low-temperature heat source by ORC aided by additional heat source
PublikacjaIn the paper presented is a concept to utilize waste heat from the power plant with the aid of the low-temperature ORC cycle. The ORC system is heated from two heat sources, the first one being the flow rate of waste heat obtained from the exhaust gases. Subsequently, the working fluid in the cycle is additionally heated by the condensing steam from the low pressure turbine extraction points increasing in such way the level of...
-
EFFECT OF NANOFLUID CONCENTRATION ON TWO-PHASE THERMOSYPHON HEAT EXCHANGER PERFORMANCE
PublikacjaAn approach – relaying on application of nanofluid as a working fluid, to improve performance of the two-phase thermosyphon heat exchanger (TPTHEx) has been proposed. The prototype heat exchanger consists of two horizontal cylindrical vessels connected by two risers and a downcomer. Tube bundles placed in the lower and upper cylinders work as an evaporator and a condenser, respectively. Distilled water and nanofluid water-Al2O3...
-
Principles and Developments of Solid-Phase Microextraction
PublikacjaSample preparation has been commonly considered a critical step of the analytical process. In this sense, remarkable efforts have been made to develop efficient sample preparation techniques which could overcome the limitations of conventional approaches. Since its inception in the early 1990’s, solid-phase microextraction (SPME) has become a widespread miniaturized sample preparation technique for extraction and preconcentration...
-
The interaction of the pulsed laser irradiation with titania nanotubes - Theoretical studies on the thermal effect
PublikacjaThis paper reports temperature dispersion simulations of titania nanotubes irradiated by the 355 nm, pulsed, nanosecond laser. The modelling with the use of Finite Elements Method concerns titania nanotubes of the length and the wall thickness in the range of 0.5–2 μm and 5–20 nm, respectively. The uniqueness of the morphology was preserved by ensuring the wall thickness variation along the height of the tube, which was determined...
-
Free Convection Heat Transfer from Horizontal Cylinders
PublikacjaThe results of experimental investigation of free convection heat transfer in a rectangular container are presented. The ability of the commonly accepted correlation equations to reproduce present experimental data was tested as well. It was assumed that the examined geometry fulfils the requirement of no-interaction between heated cylinder and bounded surfaces. In order to check this assumption recently published correlation equations...
-
Manufacturing of Lightweight Aggregates as an Auspicious Method of Sewage Sludge Utilization
Publikacja: Sewage sludge is a high-volume and low-cost waste commonly generated worldwide, so its utilization is a vital issue. The application of this waste in the manufacturing of lightweight aggregates was investigated. The process was performed using intensive mixers with volumes of 5 and 30 L, as well as the industrial 500 L mixer. Then, granulates were sintered in a tube furnace. The influence of composition and mixer size on the...
-
Synteza układu regulacji maszyny dwustronnie zasilanej zmodyfikowanego przez zastosowanie sieci neuronowej.
PublikacjaMaszyna dwustronnie zasilana stosowana jest jako generator w elektrowniach wiatrowych, gdzie występują bardzo ostre wymagania dotyczące jakości wytwarzanej energii elektrycznej oraz specyficzne problemy mechaniczne. Projekt dotyczy układu regulacji mocy maszyny dwustronnie zasilanej, będącej złożonym, nieliniowym obiektem, w którym mogą pojawiać się bardzo słabo tłumione oscylacje. Celem pracy było opracowanie układu regulacji...
-
Modelowanie małej elektowni wiatrowej
PublikacjaW pracy przedstawiono model elektrowni wiatrowej o mocy 8500W wyposażonej w generator z silnikiem synchronicznym z magnesami trwałymi. W oparciu o analizę dostępnej literatury naukowej, norm technicznych, opracowano model elektrowni wiatrowej, który został zaimplementowany w środowisku Matlab Simulink. Model ten pozwala przeprowadzić analizę elektrowni wiatrowej, w której regulacja wytwarzanej energii odbywa się z wykorzystaniem...
-
A Preliminary Study and Analysis of Tidal Stream Generators
PublikacjaFor a sustainable future, tidal energy can play a vital role. Tidal energy relies on the gravitational pull of the Moon and the Sun along with the centrifugal forces created by the Earth. Tidal barrage uses the potential energy from the tide and has been very successful in electricity production. With the help of a turbine, kinetic energy can also be harnessed from tidal currents to generate electricity. However, it is not economically...
-
Structural and catalytic properties of ceria layers doped with transition metals for SOFCs fueled by biogas
PublikacjaThe aim of this paper was to investigate an influence of the nanocrystalline Ce0.8A0.2O2-δ (A = Mn, Fe, Co, Ni, Cu) materials on the direct internal reforming of biogas in SOFC. Structural analysis of fabricated compounds has been done. An in-situ analysis of a composition of outlet gases from operating SOFC was performed using FTIR spectroscopy with simultaneous electrical tests. It was found out, that type of dopant strongly...
-
Thermochemical Conversion of Biomass and Municipal Waste into Useful Energy Using Advanced HiTAG/HiTSG Technology
PublikacjaAn advanced thermal conversion system involving high-temperature gasification of biomass and municipal waste into biofuel, syngas or hydrogen-rich gas is presented in this paper. The decomposition of solid biomass and wastes by gasification is carried out experimentally with a modern and innovative regenerator and updraft continuous gasifier, among others. A ceramic high-cycle regenerator provides extra energy for the thermal conversion...