Filtry
wszystkich: 6030
-
Katalog
- Publikacje 5330 wyników po odfiltrowaniu
- Czasopisma 71 wyników po odfiltrowaniu
- Konferencje 26 wyników po odfiltrowaniu
- Osoby 113 wyników po odfiltrowaniu
- Projekty 1 wyników po odfiltrowaniu
- Kursy Online 78 wyników po odfiltrowaniu
- Wydarzenia 6 wyników po odfiltrowaniu
- Dane Badawcze 405 wyników po odfiltrowaniu
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: CARBAMAZEPINE PROCESS OPTIMIZATION
-
Application of data driven methods in diagnostic of selected process faults of nuclear power plant steam turbine
PublikacjaArticle presents a comparison of process anomaly detection in nuclear power plant steam turbine using combination of data driven methods. Three types of faults are considered: water hammering, fouling and thermocouple fault. As a virtual plant a nonlinear, dynamic, mathe- matical steam turbine model is used. Two approaches for fault detection using one class and two class classiers are tested and compared.
-
Optimization of vortex-assisted supramolecular solvent-based liquid liquid microextraction for the determination of mercury in real water and food samples
PublikacjaA novel method was developed for sample preparation for spectrophotometric determination of Hg(II) in water and food samples. The method was based on vortex-assisted supramolecular solvent-assisted liquid-liquid microextraction (VA-SUPRASs-LLME). Analytical parameters such as pH, chelating agent, solvent type and volume, vortex time and salting out effect were optimized. Surface and normal probability plots were drawn for the variables...
-
Evaluation of Partial Nitritation/Anammox (PN/A) Process Performance and Microorganisms Community Composition under Different C/N Ratio
PublikacjaA one-stage partial nitritation/anammox (PN/A) process with intermittent aeration is possible under sidestream conditions, but implementation in a mainstream is a challenge due to increased Carbon/Nitrogen (C/N) ratios in domestic wastewater. This study investigated the effect of C/N ratios on process efficiency and the effect of narrowing non-aeration time on process improvement at high chemical oxygen demand (COD) load. An increase...
-
“Don’t call it work”: An interpretative phenomenological analysis of volunteer firefighting in young adults based on the volunteer process model
PublikacjaThe number of people engaging in volunteer firefighting is on the decline. It is important to understand what factors on a personal and social level and from the three stages of the volunteer process model: antecedents, experiences and consequences, might be linked to starting and sustaining such engagement. To address this problem, a qualitative, interview-based study was performed on a sample of 10 volunteer firefighters from...
-
Usprawnienie procesu zarządzania wymaganiami w projekcie produkcyjnym na bazie metodyki Rational Unified Process
PublikacjaArtykuł opisuje koncepcję usprawnienia procesu zarządzania wymaganiami w informatycznym przedsięwzięciu produkcyjnym z wykorzystaniem metodyki Rational Unified Process (RUP). Jest również próbą przedstawienia doświadczeń z przedsięwzięcia wdrożeniowego obejmującego automatyzację tej koncepcji z wykorzystaniem technologii IBM Rational Software i Oracle. Artykuł podkreśla krytyczną rolę mentoringu oraz efektywnego transferu wiedzy...
-
Artificial neural network prophecy of ion exchange process for Cu (II) eradication from acid mine drainage
PublikacjaThe removal of heavy metal ions from wastewater was found to be significant when the cation exchange procedure was used effectively. The model of the cation exchange process was built using an artificial neural network (ANN). The acid mine drainage waste’s Cu(II) ion was removed using Indion 730 cation exchange resin. Experimental data from 252 cycles were recorded. In a column study, 252 experimental observations validated the...
-
Thermal utilization of meat and bone meals. Performance analysis in terms of drying process, pyrolysis and kinetics of volatiles combustion
PublikacjaA development of technology of thermal utilization requires a thorough knowledge of the physicochemical properties, as well as kinetics of combustion of volatiles and char. Due to waste management regulations the meat and bone meal (MBM) is regarded as biofuel constituting one of the alternatives to fossil fuels in the energy market. MBM is a heterogeneous material that may consist of several different fractions. The extensive...
-
Optimization of the spindle speed during milling of large-sized structures with the use of technique of Experiment-Aided Virtual Prototyping
PublikacjaIn the paper are presented considerations concerning vibration suppression problems during milling of large-sized workpieces with the use of innovative method of matching the spindle speed of cutting tool. It depends on repeatable change of the spindle speed value as soon as the optimal vibration state of the workpiece approaches. The values of dominant “peaks” in the frequency spectra and the Root Mean Square (RMS) values of time...
-
Optimization of multilayer rail substrate under moving load, using metamaterials.
Publikacja -
Response Surface Methodology Application for Bacteriophage–Antibiotic Antibiofilm Activity Optimization
Publikacja -
Selected multiobjective methods for multiperiod portfolio optimization by mixed integer programming
Publikacja -
Survey of multi-objective portfolio optimization by linear and mixed integer programming
Publikacja -
A Biased-Randomized Iterated Local Search Algorithm for Rich Portfolio Optimization
Publikacja -
Optimization of a three-bed adsorption chiller by genetic algorithms and neural networks
Publikacja -
An efficient approach to optimization of semi‐stable routing in multicommodity flow networks
Publikacja -
Extended Hopfield models of neural networks for combinatorial multiobjective optimization problems
Publikacja -
Features of Machine Cyclogram Optimization with the Account of Interaction of Mechanism Links with Stops
Publikacja -
Design of dimensionally stable composites using efficient global optimization method
Publikacja -
Optimization of river network representation data models for web-based systems
Publikacja -
The Use of Evolutionary Algorithms for Optimization in the Modern Entrepreneurial Economy: Interdisciplinary Perspective
Publikacja -
Optimal Power Flow Problem Using Particle Swarm Optimization Algorithm
Publikacja -
Optimization of Parameters in Macromolecular Potential Energy Functions by Conformational Space Annealing
Publikacja -
Global Optimization-Based Method for Deriving Intermolecular Potential Parameters for Crystals
Publikacja -
Optimization of the compositions area of radiotransparent ceramic in the SrO-Al2O3-SiO2 system
Publikacja -
Optimization of ASE Conditions for the HPLC Determination of Rutin and Isoquercitrin inSambucus nigraL
Publikacja -
Evolutionary design and optimization of combinational digital circuits with respect to transistor count.
PublikacjaW artykule przedstawiono możliwość wykorzystania algorytmu ewolucyjnego do projektowania i optymalizacji cyfrowych układów kombinacyjnych w odniesieniu do liczby tranzystorów. Zastosowano chromosomy o budowie wielowarstwowej zwiększające wydajność algorytmu. Zaprojektowano, wykorzystując zaproponowaną metodę, cztery układy kombinacyjne o tabelach logicznych wybranych z literatury. Uzyskane wyniki są w wielu przypadkach lepsze...
-
The application of response surface method to optimization of precision ball end milling
Publikacja -
An automated microwave planar filter design based on space mapping optimization
Publikacja -
1+1 Protection of Overlay Distributed Computing Systems: Modeling and Optimization
PublikacjaW niniejszym artykule przedstawiono autorską koncepcję ochrony transmisji od krańca do krańca (ang. 1+1 protection) dla systemów przetwarzania rozproszonego (ang. distributed computing systems). Artykuł prezentuje nowatorskie rozwiązanie dedykowane systemom typu ''overlay'', w których system przetwarzania rozproszonego stanowi warstwę najwyższą w warstwowej architekturze sieci, korzystającą z usług warstwy sieci transportowej....
-
Frequency Guided Generalized Adaptive Notch Filtering - Tracking Analysis and Optimization
PublikacjaGeneralized adaptive notch filters (GANFs) are estimators of coefficients of quasi-periodically time-varying systems, encountered e.g., in RF applications when Doppler effect takes place. Current state of the art GANFs can deliver highly accurate estimates of system variations’ frequency, but underperform in terms of accuracy of system coefficient estimates. The paper proposes a novel multistage GANF with improved coefficient...
-
Innovative optimization algorithm of variable speed pumps in district heating systems.
PublikacjaW referacie przedstawiono innowacyjny algorytm matematyczny optymalizacji pracy pomp zmienno prędkościowych w systemach ciepłowniczych. Algorytm wykorzystuje procedurę iterecyjnego wyznaczania parametrów pracy pomp, których charakterystyki są linearyzowane odcinkami w układzie dwóch współrzędnych. Do rozwiązania modelu całkowitoliczbowego zaproponowano wykorzystanie systemu GAMS. W pracy przedstawiono podstawy metodologiczne i...
-
Removal of Siloxanes from Model Biogas by Means of Deep Eutectic Solvents in Absorption Process
PublikacjaThe paper presents the screening of 20 deep eutectic solvents (DESs) composed of tetrapropylammonium bromide (TPABr) and glycols in various molar ratios, and 6 conventional solvents as absorbents for removal of siloxanes from model biogas stream. The screening was achieved using the conductor-like screening model for real solvents (COSMO-RS) based on the comparison of siloxane solubility in DESs. For the DES which was characterized...
-
Instrumented end notched flexure - Crack propagation and process zonemonitoring Part II: Data reduction and experimental
PublikacjaA mode II instrumented end notched flexure three point bending (ENF) adhesion test is described. The adhesive joint consists of two aluminium alloy (AW7075-T6) plates bonded with a structural epoxy adhesive (Hysol EA 9395™). Strain gauges are attached to the outer surface (backface) of the substrates in the lengthwise direction to measure local surface strain during crack propagation. Simultaneously, load/displacement measurements...
-
Monitoring of n-butanol vapors biofiltration process using an electronic nose combined with calibration models
PublikacjaMalodours, by definition, are generally unpleasant, nuisance smells that are a mixture of volatile chemical compounds which can be perceptible even at low concentrations. Due to the more frequent occurrence of odour nuisance associated with the odour sensations, and thus the need to remove them from the air, deodorization techniques are commonly used. Biofiltration is one of the methods of reducing odorants in the air stream. In...
-
A literature survey of the influence of preform reheating and stretch blow moulding with hot mould process parameters on the properties of PET containers – part 2.
PublikacjaThe hot fill process is an inexpensive conventional filling technology for high-acidity products (pH < 4.5). It allows certain drinks (sensitive beverages such as fruit and vegetable juices, nectars, soft drinks, vitaminised water) to be stored at ambient temperature without the need for chemical preservatives. The primary feature of the bottles used in the hot fill process is their temperature stability, i.e. the ability to retain...
-
A literature survey of the influence of preform reheating and stretch blow molding with hot mold process parameters on the properties of PET containers. Part I.
PublikacjaThe hot fill process is an inexpensive conventional filling technology for high-acidity products (pH < 4.5). It allows certain drinks (sensitive beverages such as fruit and vegetable juices, nectars, soft drinks, vitaminized water) to be stored at ambient temperature without the need for chemical preservatives. The primary feature of the bottles used in the hot fill process is their temperature stability, i.e. the ability to retain...
-
Spectroscopic studies of a ring opening process between epoxy- and aminosilanes and imine formation reactions in aqueous solutions
PublikacjaNMR and Raman spectroscopy studies were performed for different 3-aminopropyl(trimethoxy)- and 3-glycidoxypropyl (trimethoxy)silane based sol-gel systems containing different ketones. Exceptionally stable imine products were obtained depending on a reaction system at alkaline pH conditions and in the presence of water. These imine formation reactions were carried out without further catalyst. In addition, effect of water for the...
-
Effect of some organic solvent - water mixtures composion on precipitated calcium carbonate in carbonation process
PublikacjaPrecipitated calcium carbonate particles were obtained during carbonation of calcium hydroxide slurry with carbon dioxide. Aqueous solutions of isopropyl alcohol, n-butanol and glycerol were used as solvents. Concentration of organic additives in the reactive mixture was from 0 to 20 % (vol.). Precipitation process were performed in a stirred tank reactor equipped with gas distributor. Multimodal courses of particles size distribution...
-
Evaluation of the Construction and Investment Process of a High-Pressure Gas Pipeline with Use of the Trenchless Method and Open Excavation Method. Analytic Hierarchy Process (AHP)
Publikacja -
The impact of hydrological research, municipal authorities, and residents on rainwater management in Gdańsk (Poland) in the process of adapting the city to climate change
PublikacjaAim of the study The city of Gdańsk faces changing climatic conditions that result in a higher frequency of extreme weather events. In response to the increasingly frequent appearance of flash floods, scientific research was carried out on changes in the probability of the occurrence of maximum daily precipitation in Gdańsk. The purpose of this paper is to show the role of hydrological research (science), decisions of local authorities...
-
Coda wave interferometry in monitoring the fracture process of concrete beams under bending test
PublikacjaEarly detection of damage is necessary for the safe and reliable use of civil engineering structures made of concrete. Recently, the identification of micro-cracks in concrete has become an area of growing interest, especially using wave-based techniques. In this paper, a non-destructive testing approach for the characterization of the fracture process was presented. Experimental tests were made on concrete beams subjected to mechanical...
-
Interdisciplinary research as a form of monument protection and preparation for the investment process on the example of the former Gdańsk Shipyard complex
PublikacjaThe multi-layered heritage of many industrial plants operating until the end of the 20th century creates a particular challenge for conservators, designers and investors. In the process of protecting its values, displaying qualities and managing the property, it is necessary to recognize a wider transformation of technology of the entire plant and the individual functions of its buildings, as well as the context of intangible...
-
The clamping selection method to reduce the vibration of large-size workpieces during the face milling process
PublikacjaThe article introduces a method for selecting the best clamping conditions to obtain vibration reduction during milling of large-size workpiece. It is based on experimental modal analysis performed for a set of assumed, fixing conditions of a considered workpiece to identify Frequency Response Functions (FRFs) for each tightening torque of the mounting screws. Simulated plots of periodically changing nominal cutting forces are...
-
Assessment of the devulcanization process of EPDM waste from roofing systems by combined thermomechanical/microwave procedures
PublikacjaEthylene-propylene-diene rubber (EPDM) is a elastomer widely used in common industrial applications. EPDM can be shaped into sheets and employed as isolating material for roofing systems. In this study, scraps of EPDM from commercial, industrial and residential roofing systems were treated by combined thermo-mechanical and microwave devulcanization processes including peroxide of benzoyl (BPO). The devulcanized EPDM (Dev-EPDM)...
-
Assessing ecotoxicity, synergic and antagonistic actions of commonly used components of polymerization mixture in molecularly imprinted polymers preparation process
PublikacjaIncreasingly, the challenge is the optimal process of developing a suitable MIP-type sorptive material (taking into account its final form and application area), which is mainly related to the efficiency/effectiveness of the polymerization process. The lack of reaction or its low efficiency generates additional waste and puts it into the environmental cycle. The main aim of the performed research was the estimation of ecotoxicity,...
-
Influence of process of straightening ship hull structure made of 316L stainless steel on corrosion resistance and mechanical properties
PublikacjaThe AISI 316L type steel belongs to the group of chromium-nickel stainless steels. They are determined according to European standards as X2CrNiMo17-12-2 and belong to the group of austenitic stainless steels. Steels of this group are used for elements working in seawater environments, for installations in the chemical, paper, and food, industries, for architectural elements, and many others. The chemical composition of corrosion-resistant...
-
Recycled rubber wastes-based polymer composites with flame retardancy and electrical conductivity: Rational design, modeling and optimization
PublikacjaPolymer recycling techniques experience a maturity period of design and application. Rubbers comprise a high proportion of polymer wastes, highly flammable and impossible to re-melt. Polymer composites based on ground tire rubber (GTR) and ethylene-vinyl acetate copolymer (EVA) containing carbon black (CB) (1–50 phr), with variable EVA/GTR weight composition (10/90, 25/75, 50/50, 75/25 and 90/10), and processing temperature (Low:...
-
Modification and Optimization of the United-Residue (UNRES) Potential Energy Function for Canonical Simulations. I. Temperature Dependence of the Effective Energy Function and Tests of the Optimization Method with Single Training Proteins
Publikacja -
Influence of reduction process on the structural and mechanical properties of (Pb,Bi)-(Si,Ge)-O oxide glasses
PublikacjaThe effect of the reduction process in H2 at 380 °C on the microstructure and elemental composition of a glass Bi0.4Pb0.2Si0.4Ox has been investigated. It has been shown that after reduction a clearly separated top layer with a thickness of approx. 50 µm was formed on the surface of the sample. This layer is depleted of oxygen and has higher electrical conductivity than the interior of the glass. It has also been found that some...
-
Virtual Engineering Object / Virtual Engineering Process: A specialized form of Cyber Physical System for Industrie 4.0
PublikacjaThis paper reviews the theories, parallels and variances between Virtual Engineering Object (VEO) / Virtual Engineering Process (VEP) and Cyber Physical System (CPS). VEO and VEP is an experience based knowledge representation of engineering objects and processes respectively. Cyber–physical systems (CPSs) are the next generation of engineered systems in which computing, communication, and control technologies are tightly integrated....