Wyniki wyszukiwania dla: POLYMER TECHNOLOGY
-
Evaluation of Low Temperature Properties of Rubberized Asphalt Mixtures
PublikacjaThe paper presents low-temperature test results of asphalt mixtures designed with use of bitumen modified by crumb rubber and also SBS polymer. Laboratory tests were conducted on two types of asphalt mixtures for wearing course – stone matrix asphalt (SMA 8) and porous asphalt (PA 8). This paper presents results of the following laboratory tests at low temperatures: TSRST test, three point bending creep test, fracture toughness...
-
Recent Advances in Development of Waste-Based Polymer Materials: A Review
PublikacjaLimited petroleum sources, suitable law regulations, and higher awareness within society has caused sustainable development of manufacturing and recycling of polymer blends and composites to be gaining increasing attention. This work aims to report recent advances in the manufacturing of environmentally friendly and low-cost polymer materials based on post-production and postconsumer wastes. Sustainable development of three groups...
-
Investigation on polypropylene friction stir joint: effects of tool tilt angle on heat flux, material flow and defect formation
PublikacjaTool tilt angle (TTA) is a critical factor that can control material flow in polymeric materials' friction stir joining (FSJ). This study selected a TTA range between 0° to 4° for FSJ of polypropylene (PP) polymer sheet. A modified computational fluid dynamic (CFD) technique was implemented to gain a deep understanding of the effects of TTA during FSJ of PP. The PP joint's internal flow, defect formation, heat generation, and tensile...
-
Preliminary Testing of the Influence of Modified Polycaprolactones on Anabaena Variabilis Growth in Seawater
PublikacjaSeveral new biodegradable polymer materials have recently come onto the global market. Mostly the results on degradation kinetic studies are presented. This paper suggests using one of the tests to estimate the impact of polymer packaging material on sea life. The microorganism chosen was Anabaena variabilis (identified in many waters, including those of the Baltic Sea, especially in the Gulf of Gdansk and Puck Bay; this cyanobacterium...
-
Interface analysis of compatibilized polymer blends
PublikacjaThis chapter seeks to address the interface location in the compatibilized polymer blends and paves the way for quantitative analysis of interface in terms of interfacial tension and interfacial adhesion to provide support for understanding the relationship between morphology and ultimate properties in the compatibilized polymer blends through the lens of interface. Since understanding and analysis of interfacial phenomena in the...
-
In-situ and ex-situ resistance measurements of polypyrrole film using double-band electrode
PublikacjaMany in-situ techniques are performed in order to determine the resistance of conducting polymer film. However, the resistance measured in solution can be the combination of polymer resistance and that of other components, such as resistance of supporting electrolyte. Therefore, in this work, the influence of the solution on the resistance of polypyrrole (PPy) film has been studied. PPy film was electrchemically synthesized onto...
-
Phase separation in poly(butylene terephthalate)-based materials prepared by solid-state modification
PublikacjaThe morphology of a series of poly(butylene terephthalate) (PBT)/fatty acid dimer diol (FADD)-based copolyesters prepared by solid-state modi fi cation (SSM) was studied. It was shown that in copolyesters containing less than 10 wt% FADD two different phases, i.e. a PBT crystalline phase and a PBT-rich amorphous phase, are present. The FADD residues were more or less homogeneously distributed throughout the interlamellar regions....
-
High-resolution microscopy assisted mechanical modeling of ultrafine electrospun network
Publikacja -
Influence of e-beam irradiation on the dynamic creep and fatigue properties of poly(aliphatic/aromatic-ester) copolymers for biomedical applications
Publikacja -
Physical effects of radiation processes in poly(aliphatic/aromatic-ester)s modified with e-beam radiation
Publikacja -
Dispersion of thermo-optic coefficient of optical polymers
Publikacja -
Improved conformational space annealing method to treat β-structure with the UNRES force-field and to enhance scalability of parallel implementation
Publikacja -
Effective SERS materials by loading Ag nanoparticles into poly(acrylic acid-stat-acrylamide)-block-polystyrene nano-objects prepared by PISA
Publikacja -
Growth of polymer brushes by “grafting from” via ATRP – Monte Carlo simulations
Publikacja -
Combination of fumed silica with carbon black for simultaneously improving the thermal stability, flame retardancy and mechanical properties of polyethylene
Publikacja -
Development of nanoscale morphology and role of viscoelastic phase separation on the properties of epoxy/recycled polyurethane blends
PublikacjaA novel and cost-effective approach towards the modification of epoxy matrix has been developed using recycled polyurethane for the first time without sacrificing any of the intrinsic properties of the resin. Polyurethane, recycled from waste foam by glycolysis process (RPU), was found to be very effective in improving the properties of the thermosetting resin based on Diglycidyl ether of bisphenol-A (DGEBA). The effect of the...
-
Novel bio-based thermoplastic poly(ether-urethane)s. Correlations between the structure, processing and properties
PublikacjaThe main purpose of this work was to analyze the effect of the number of unreacted isocyanate groups and the [NCO]/[OH] molar ratio during the chain extension of a prepolymer during the polymerization process on the structure, processing and selected properties of thermoplastic poly(ether-urethane)s. Three series of novel thermoplastic polyurethanes were obtained via a prepolymer route. Three prepolymers were synthesized from diisocyanate...
-
Synthesis of isotactic polypropylene- block -polystyrene block copolymers as compatibilizers for isotactic polypropylene/polyphenylene oxide blends
PublikacjaPoly(2,6-dimethyl-1,4-phenylene oxide) (PPO) and isotactic polypropylene (iPP) are highly incompatible and consequently their uncompatibilized blends are quite brittle regardless of the molecular weights and ductility of the individual components. Isotactic polypropylene-polystyrene block copolymers, to be applied as compatibilizers for a broad range of PPO/iPP blend compositions, were prepared by mechanism transformation from...
-
Mechanical lithography in a polymer substrate using AFM in contact mode
Dane BadawczeMechanical lithography in a polymer substrate. Contact mode. NTEGRA Prima (NT-MDT) device. NSG 01 probe.
-
Flame-Retardant Polymer Materials Developed by Reactive Extrusion: Present Status and Future Perspectives
PublikacjaThe development of flame retardant polymer materials has two roots, one in materials design, and the other in materials processing. Over recent decades, different types and classes of flame retardant polymer materials have been commercialized to meet safety requirements in the construction, automotive, and coatings industries. In the vast majority of cases, the design and fabrication of new materials presenting low fire hazards...
-
Electrochemical Activity and Electrical Properties of Optimized Polypyrrole Coatings on Iron
PublikacjaIn this work, electrochemical activity and electrical properties of polypyrrole (PPy) coated iron electrodes have been investigated. PPy film was electrochemically polymerized from sodium salicylate aqueous solution under conditions, which provided an increase of iron corrosion resistance. It was noticed that the pH of the solution and the applied electrode potential range during the study of the polymer properties had an influence...
-
Study of the Effect of Filling Thermoplastic Medical Polyurethane with PVA, PLA or Diatomite on the Relaxation Times Distributions of 1H NMR
PublikacjaIn this work, to characterize the mobility of diferent sections of the macromole‑ cules of polyurethane (PUR), polyvinyl alcohol (PVA), and polylactic acid (PLA), as well as the density of crosslinks of the polymer chains when using fllers, we used the distributions of spin–lattice and spin–spin relaxation times for the protons. It is shown that the rigidity of the thermoplastic polymers depends on the sizes of the granules of...
-
Interrelated shape memory and Payne effect in polyurethane/graphene oxide nanocomposites
PublikacjaWe report the fabrication of graphene oxide (GO) based polyurethane (PU) nanocomposites by a simple method of mixing and their shape memory properties at different temperatures. Both the polymer and the filler were synthesized in the laboratory by simple and easy methods – PU by pre-polymer method and GO by improved graphene oxide synthesis method. High molecular level dispersion of GO platelets within the PU matrix and thus good...
-
Effect of Coating Material Properties on Tilting-pad Thrust Bearing Performance
PublikacjaPolymer lined tilting-pad bearings demonstrate many advantages over traditional bearing systems. Bearings with a polymer layer in comparison with a babbitted layer show, for example: lower value of friction coefficient (important during start/stops), higher fatigue strength of the coating, better distribution of the load on individual pads due to lower elasticity of the polymers, wider range of operational temperatures or the ability...
-
Investigation of behaviour of metal structures with polymer dampers under dynamic loads
PublikacjaA large number of accidents concerning structures subjected to dynamic loads have been recently observed. One of the examples of such a structure is a temporary steel grandstand erected using scaffolding system. Dynamic load that is generated by crowd movement has a significant influence on the behaviour of the structure and may lead to excessive structural vibrations. The aim of the study is to consider the idea of using polymer...
-
Study of Aliphatic Polyurethanes by the Low-Field 1H NMR Relaxometry Method with the Inversion of the Integral Transformation
PublikacjaIn this paper, the distributions of the 1H nuclear magnetic resonance (NMR) spin–lattice and spin–spin relaxation times are used to characterize the mobility of different sections of macromolecules of aliphatic polyurethanes and the cross-linking density of polymer chains. The NMR relaxometry method with inversion of integral transformation is applied to study the effect of poly (ethylene glycol) and glycerol phosphate calcium...
-
Structure-rheology relationship of fully bio-based linear polyester polyols for polyurethanes - Synthesis and investigation
PublikacjaThe synthesis of polyols from renewable substances as an alternative for petrochemical-based polyols play important matter in the polyurethane industry. In this work, the fully bio-based linear polyester polyols with different catalyst amounts were synthesized via two-step polycondensation method. The effect of various catalyst content on the structure and rheological behavior were established. Fourier Transform Infrared Spectroscopy,...
-
Application of polymer element in reduction of temporary steel grandstand vibrations
PublikacjaThe numerical analysis focused on reduction of vibrations of a temporary steel scaffolding grandstand has been conducted in this paper. These types of structures are regularly subjected to dynamic loads which, in conjunction with light and quite slender structural members, may induce dangerous vibrations. To increase their safety, temporary steel grandstands are usually strengthened with the diagonal stiffeners of tubular cross...
-
Experimental study on the effectiveness of polymer damper in damage reduction of temporary steel grandstand
PublikacjaA large number of accidents, involving collapses of temporary grandstands during different types of events, were observed in the past. If the synchronized movement of people is tuned with the natural frequency of the affected part of the structure, resonance might occur. It may lead to severe damages of grandstands, their collapse or panic among the spectators. The aim of the paper is to assess, through preliminary experimental...
-
Synthesis and structural characterization of bio-based bis(cyclic carbonate)s for the preparation of non-isocyanate polyurethanes
PublikacjaBio-based cyclic carbonates are of significant research interest as monomers for non-isocyanate polyurethane (NIPU) synthesis. This research describes the synthesis of a series of five-membered bis(cyclic carbonate)s using bio-based polyether polyols (PO3G) with different molecular weights (250, 650 and 1000 g mol−1) and carbon dioxide as green feedstocks. The utilization of CO2 as a source of carbon in the chemical reaction is...
-
Fabrication and properties of electrode material composed of ordered titania nanotubes and pEDOT:PSS
PublikacjaWe report on the two-stage preparation method of electrode material composed of titania nanotubes and poly(3,4-ethylenedioxythiopene):poly(2-styrenesulphonate) conductive polymer (pEDOT:PSS). Initially, titania nanotube arrays were produced by the anodization process of Ti substrate. Next, the polymer was potentiostatically deposited onto the thermally annealed nanotube arrays from the electrolyte containing monomer and counter...
-
Benzene-induced hydro(solvo)thermal synthesis of Cu2+ and Zn2+ coordination polymers based on 1,3-benzenedicarboxylate
PublikacjaHydro(solvo)thermal reactions of Cu(NO3)2·2.5H2O or Zn(NO3)2·6H2O with 1,3-H2bdc provided two structurally different coordination polymers; a 2D network “metallacalixarene” based on the paddlewheel-type cluster with the formula [Cu(1,3-bdc)·H2O]·H2O (1) and a 3D framework [Zn(1,3-bdc)] (2), respectively. The use of a base was unnecessary in this synthesis; however, the presence of benzene played a crucial role in the crystallization...
-
Preparation, morphology and properties of natural rubber composites filled with untreated short jute fibres
PublikacjaGreen composites were obtained by incorporation of short jute fibres in natural rubber matrix using a laboratory two-roll mill. The influence of untreated fibre content (1, 2.5, 5, 7.5 and 10 phr) on the mechanical properties, dynamic mechanical properties, swelling properties was examined. The behaviour of prepared green composites under cyclic compression was also investigated. Fibre dispersion in rubber matrix was studied by...
-
Experimental study on polymer mass used to repair damaged structures
PublikacjaA new method of repairing damaged structures by injecting the cracks with specially designed polymer mass (flexible two-component grout based on polyurethane resin) has been recently proposed. The technique is mainly dedicated to damaged masonries, especially historical structures where minimum intervention is permitted. The cracks are filled with the special injection, forming the flexible joints bonding the disrupted structural...
-
Lead(II) coordination polymers with imidazole-4- and pyrazole-3-carboxylate isomeric linkers: Structural diversity and luminescence properties
PublikacjaUsing 1H-imidazole-4-carboxylic acid (4imCOOH) and 1H-pyrazole-3-carboxylic acid (3pyrCOOH) coordination polymers [Pb(4imCOO)2(H2O)]n (1) and [Pb2(3pyrCOO)4]n (2) were constructed. Obtained polymers were characterized via FT-IR, X-ray, PL and TG methods. The coordination polyhedron around Pb(II) in 1 is described as distorted pentagonal pyramid with hemidirected coordination sphere (based on DFT calculations). Compound 2 consists...
-
Morphology and properties of recycled polyethylene/ground tyre rubber/thermoplastic poly(ester-urethane) blends
PublikacjaThe growing amount of plastics waste produced every year resulted in development of mechanical and chemical recycling methods of polymers and their blends or composites. From the environmental point of view, the possibility of plastics waste reusing and recycling is desirable. In this study three polymer blends were obtained with using recycled polyethylene (RPE), ground tyre rubber (GTR) and thermoplastic poly(ester-urethane)...
-
An experimental study on polymer mass
PublikacjaA new method of repairing damaged structures by filling the cracks with specially prepared polymer mass has been recently proposed. The technique is mainly dedicated to historical objects where minimum intervention is permitted. The flexible joint bonds the disrupted elements and ensures further safe exploitation of a damaged structure. The aim of the present paper is to show the results of an experimental study on polymer mass...
-
Dynamics of Chains as a Tool to Study Thermomechanical Properties of Proteins.
PublikacjaPolymer dynamics can be formulated on different levels of detail. One approach eliminates microscopic degrees of freedom and a polymer molecule is represented by a simplified structure—a chain. In the simplest case monomers of ideal chain have fixed length, and their orientation is independent of the orientations and positions of neighbouring monomers. This is reason that two monomers can co-exist at the same place. Ideal chain...
-
Enhanced aging resistance of poly(ε-caprolactone)/brewers’ spent grain composites
PublikacjaThe presented paper investigated the influence of brewers’ spent grain (BSG) extrusion pa-rameters on the photo-oxidative resistance of poly(ε-caprolactone)-based wood polymer composites. Filler samples characterized by the higher melanoidin content were more efficient in hindering of poly-mer degradation, inhibiting the decomposition of the polymer amorphous phase. As aresult, deteriora-tion of mechanical performance was limited,...
-
Recent Advances in Polymer Nanocomposites: Unveiling the Frontier of Shape Memory and Self-Healing Properties—A Comprehensive Review
PublikacjaShape memory and self-healing polymer nanocomposites have attracted considerable attention due to their modifiable properties and promising applications. The incorporation of nanomaterials (polypyrrole, carboxyl methyl cellulose, carbon nanotubes, titania nanotubes, graphene, graphene oxide, mesoporous silica) into these polymers has significantly enhanced their performance, opening up new avenues for diverse applications. The...
-
Topological behavior mimicking ethylene–hexene copolymers using branched lactones and macrolactones
PublikacjaPolyolefins are of paramount importance in the world of polymers due to their technological and economic potential.1 However, their nonpolar character significantly restricts the compatibility and adhesion properties, which consequently limits their versatility. Moreover, an intensified demand for materials from renewable resources can also become a problematic venture for the current polyolefin industry.2 Although Braskem and...
-
Measurements of guided wave propagation in CFRP/steel adhesive joints obtained by scanning laser vibrometry
Dane BadawczeThe DataSet contains guided wave signals measured in adhesive joints of steel plates (steel of type S355 with a thickness of 11.9 mm ) and carbon fibre reinforced polymer (CarboDur S1012 with a thickness of 1.24 mm). The samples were as follows: #0 – intact; #1 – 10% disbond; #2 – 20% disbond; #3 – 50% disbond; #4 – 80% disbond; #5 – 100% disbond.
-
Temperature Coefficient of Electronic Polarizability in Thin Polymer Films Deposited on Si and SiO2 Substrates Determined via Spectroscopic Ellipsometry
PublikacjaEllipsometry is widely used to determine the thermo-optical properties of thin polymer films. However, if the thermo-optic coefficient (TOC) and the linear thermal expansion coefficient (LTEC) are to be used to determine the temperature coefficient of electronic polarizability (TCEP) in thin polymer films, their values must be determined with the greatest possible accuracy, as both have the opposite effect. In this article,...
-
Synthesis and electrochemical characteristics of novel dithiocarbamate polymers
PublikacjaNovel dithiocarbamate compounds have been obtained by reacting a linear poly(ethylenimine)polymer, MW 50,000, with CS2. The resulting anionic polymers contain, depending on the reaction conditions, up to two sulfur atoms per one nitrogen atom (approx. 40% w/w). The polymers are soluble in dimethylsulfoxide and insoluble in acetonitrile solutions. In both solvents they are electrochemically active, in the latter case as a cast film...
-
Highly stable organic–inorganic junction composed of hydrogenated titania nanotubes infiltrated by a conducting polymer
PublikacjaA poly(3,4-ethylenedioxythiophene) conducting polymer doped with poly(2-styrene sulfonate) (pEDOT:PSS) was efficiently electrodeposited on a layer composed of ordered titania nanotubes. TiO2 nanotubes were formed during an anodization process and, after calcinations, a layer was subjected to hydrogen plasma. Hydrogenation leads to Ti(III) formation, a decrease in resistance, and a huge increase of donor density when compared with...
-
Degradation of polycaprolactone modified with TPS or CaCO3 in biotic/abiotic seawater
PublikacjaThis paper is an investigation of the polymer degradation process in two types of seawater (with and without microorganisms) sourced from the Baltic Sea. The chosen polymeric materials were polycaprolactone modified with either thermoplastic starch (PCL/TPS>85%) or calcium carbonate (60% PCL/40% CaCO3) compared directly against unmodified polycaprolactone. All samples were incubated for 28 weeks in seawater with and without microorganisms...
-
Molecular dynamics simulations of the growth of poly (chloro-para-xylylene) films.
PublikacjaParylene C, poly(chloro-para-xylylene) is the most widely used member of the parylene family due to its excellent chemical and physical properties. In this work we analyzed the formation of the parylene C film using molecular mechanics and molecular dynamics methods. A five unit chain is necessary to create a stable hydrophobic cluster and to adhere to a covered surface. Two scenarios were deemed to take place. The obtained results...
-
Experimental Research on Insufficient Water Lubrication of Marine Stern Tube Journal Bearing with Elastic Polymer Bush
PublikacjaWater-lubricated bearings with polymer bushes are steadily gaining popularity due to their advantages, including environmental friendliness, relatively simple construction and long-term operation. Nevertheless, in practice instances of damage to such bearings occur due to insufficient or absent flow of the lubricating agent. In this study, experimental tests established that elastic polymer bush bearing is capable of operating...
-
Experimental study on effectiveness of polymer dampers in reduction of structural vibrations
PublikacjaVibrations of civil engineering structures, generated by dynamic loads, may be very dangerous to the structures themselves as well as may have significant influence on human perception and comfort. A number of different methods have been proposed in order to minimize such situations. This concern newly designed structures as well as those which dynamic properties have to be modified due to problems with excessive vibrations. One...
-
Experimental study on the effectiveness of polymer dampers in reduction of structural vibrations
PublikacjaVibrations of civil engineering structures, generated by dynamic loads, may be very dangerous to the structures themselves as well as may have significant influence on human perception and comfort. A number of different methods have been proposed in order to minimize such situations. This concern newly designed structures as well as those which dynamic properties have to be modified due to problems with excessive vibrations. One...