Wyszukiwarka
Wyniki wyszukiwania dla: PUMP LOAD, RESEARCH HYPOTHESIS, FUEL OIL
-
Experimental research on a hydrodynamic thrust bearing with hydrostatic lift pockets: Influence of lubrication modes on bearing performance
PublikacjaThe aim of the study is to investigate the performance of a thrust bearing equipped with hydrostatic lift pockets under different lubrication modes. Three types of flat land bearing lubrication modes are studied experimentally: hydrostatic lubrication (HS; forced oil injection to the pockets), hybrid lubrication (HS + HD; hydrostatic lubrication combined with the external forced bearing oil supply) and hydrodynamic lubrication...
-
Improving performance of large thrust bearings through modeling and experimentation
PublikacjaLarge thrust bearings are highly loaded machine elements and their failures cause serious losses. Start ups and stoppages of the bearing under load are specially critical regimes of operation. Load carrying capacity depends on the profile of the oil gap. In transient states this profile is also changing. In the design of large thrust bearings minimizing thermo-elastic deformations is an important goal, which can be accomplished...
-
Rational Use of Primary Energy in Single-Family Residential Houses
PublikacjaThis work presents results of the primary energy use for heating residential single-family house. Analysis includes domestic hot water system (DHW) and heating, ventilation and air condition system (HVAC). During researches the conventional and alternative energy sources (natural gas, biomass, fuel oil, bituminous coal, lignite or electric energy obtained from electric power system – EPS) were used in DHW and HVAC systems. Furthermore...
-
Large thermo-elastic displacement and stability FEM analysis of multilayered plates and shells
PublikacjaThe paper concerns the load capacity analysis of thermally loaded multilayered plates and shells. The multilayered body is treated as an equivalent single layer whose kinematics is consistent with first order shear deformation theory. The authors focus on the thermo-elastic stability problem of the thin-walled structures. The equilibrium paths are traced with the use of Riks-Wempner-Ramm algorithm. By making use of the Tsai-Wu...
-
Satelitowy agregat pompowy
PublikacjaW artykule opisano najnowszą konstrukcję satelitowego agregatu pompowego charakteryzującego się tym, że pompa satelitowa jest umieszczona wewnątrz silnika elektrycznego i zasysa ciecz poprzez otwór wydrążony osiowo w wale silnika. Zastosowana w agregacie pompa satelitowa jest nowatorską konstrukcją zawierającą mechanizm satelitowy o odwróconej kinematyce znamienny tym, że planeta (wirnik) oraz płyty kompensacyjne (rozrządu) są...
-
Influence of Wastewater Treatment Technology on Particle Size Distribution in the Effluent
PublikacjaSuspended solids in water and wastewater usually carry quite a large load of pollutants (organic substances, nutrients, heavy metals, etc.) adsorbed on the particles surface. Particles of different sizes carry different types and quantities of pollutants. Therefore, particle size distribution is of importance in waster and wastewater treatment. In the article the influence of different treatment technologies on particle size distribution...
-
Oil removal from polluted soil by washing with surfactants solutions in dynamic conditions
PublikacjaFor washing of the oil from polluted soil surfactants solutions were applied. In a research a nonionic synthetic surfactant - polyoxyethylene ether of synthetic fatty alcohol (Rokanol NL6), rhamnolipid biosurfactant JBR 425 (Jeneil Biosurfactant Co. LLC) and their mixtures were used. Results of oil removal from peat soil and sand with mixtures of surfactants solutions at concentration 0,5 g/dm...
-
Field tests on hydrodynamic and hybrid operation of a bi-directional thrust bearing of a pump-turbine
PublikacjaIn vertical shaft pump turbines operating in pumped storage power plants an important role is played by a thrust bearing. Because of bi-directional character of operation, thrust bearing tilting pads have to be supported symmetrically, which is known to be unfavourable from the point of view of their performance. Large thrust bearings have to be carefully designed so as to minimise excessive thermo-elastic pad deformations. The...
-
Field Tests on Hydrodynamic and Hybrid Operation of a Bidirectional Thrust Bearing of a Pump-Turbine
PublikacjaIn vertical shaft pump turbines operating in pumped storage power plants an important role is played by a thrust bearing. Due to the bidirectional character of operation, thrust bearing tilting pads have to be supported symmetrically, which is known to be unfavourable from the point of view of their performance. Large thrust bearings have to be carefully designed so as to minimise excessive thermo-elastic pad deformations. The...
-
Effect of gelation and storage conditions on the oxidative stability of microemulsion and nanoemulsion delivery systems
PublikacjaIncreased interest in the use of microemulsion and nanoemulsion delivery systems for medical, cosmetic and food purposes, promotes the development of research on their physical and chemical stability, and the safety of use. Here, we have for the first time evaluated the oxidative stability of linseed oil dispersed in the microemulsion, nanoemulsion, and their gelled systems, stored under different conditions, and compared to the...
-
Marine Fuel Sulphur Limit Impact on Air Pollution
PublikacjaThe article presents calculation of Sulphur oxides percentage drop rate in marine industry recorded after 01.01.2020 when new limits, provided by International Maritime Organizations legislation, became effective. Ships’ SOx global emission was estimated and compared between 4th quarter 2019 and 1st quarter 2020. For more accurate estimation 3 seaside cities with big harbors were selected for statistical analysis. Noticeable...
-
BJS-03 DO WE NEED FIXATION OF THE MESH IN LAPAROENDOSCOPIC TECHNIQUES FOR M3 INGUINAL DEFECTS? AN EXPERIMENTAL STUDY
PublikacjaThe authors conducted a research experiment to verify the hypothesis that it is possible to preserve the mesh in the operating field in large direct hernias (M3) without the need to use fixing materials. The results showed that mesh fixation is not the only alternative to preventing recurrence in complex defects and that the type of implant seems to be a key factor from the point of view of mechanics and biophysics.
-
High Temperature Air/Steam Conversion of Biomass and Wastes Into Fuel Gas for Heat and Electricity Production
PublikacjaPaper present principle of high temperature air/staem gasification as well as some results of research using this technology for conversion of biomass and wastes into fuel gas.
-
Pyrolysis and Torrefaction—Thermal Treatment of Creosote-Impregnated Railroad Ties as a Method of Utilization
PublikacjaA fundamental issue of waste management and the rail transport industry is the problem of utilizing used railroad ties. Wooden railroad ties are treated with a preservative, usually creosote. Due to their high toxicity, railroad ties are considered hazardous waste and must be utilized under various directives. It is proposed to utilize the troublesome waste by using the pyrolysis and torrefaction process. The research proves that...
-
The Application of a Mobile Unmanned Device for Monitoring Water and Sediment Pollution in the Port of Gdynia
PublikacjaPollution in the Port of Gdynia can encompass various types of substances and contaminants that affect the quality of water and sediment in this region. Ships entering and leaving the port can release pollutants such as oil, fuel, waste, and chemicals into the water. Controlling and monitoring these pollutants is a crucial part of environmental stewardship. In recent years, uncrewed units have been increasingly in use for in situ...
-
The Thin-Layer Microchromatography (μTLC) and TLC–FID Technique as a New Methodology in the Study of Lubricating Oils
PublikacjaThis paper concerns the possibility of using TLC coupled with a flame ionization detector (FID) and micro-TLC (μTLC) as precursors for microfluidized devices of analytical techniques to identify and determine the presence and content of the petroleum/vegetable oil base in the lubricating oils applied in cutting devices (chainsaws). This research is related to the problem of ensuring, in compliance with the requirements of environmental...
-
INFLUENCE OF LOAD AND INFLATION PRESSURE ON THE TYRE ROLLING RESISTANCE
PublikacjaTyre load and inflation pressure are important factors controlling rolling resistance of road vehicles. The article presents results obtained in the Technical University of Gdańsk during laboratory and road measurements of different car tyres rolling on different pavements. The knowledge of rolling resistance characteristics is important for modelling car dynamics as well as fuel consumption. It is also necessary to establish proper...
-
The “autumn effect” in the gold market—does it contradict the Adaptive Market Hypothesis?
PublikacjaThe present study aims to verify the autumn effect in the gold market, first presented 10 years ago by Dirk Baur in the paper “The autumn effect of gold” and to investigate the calendar effects occurring for other precious metals. This empirical research is presented in a way to place the results obtained in the context of the Efficient Market Hypothesis (EMH) and the more current Adaptive Market Hypothesis (AMH). The study was...
-
DME as alternative fuel for compression ignition engines – a review
PublikacjaThe ecological issues and the depletion of crude oil, has led the researchers to seeking for non-petroleum based alternative fuels, along with more advanced combustion technologies, and after-treatment systems. The use of clean alternative fuels is the one of the most perspective method that aiming at resolving of the said issues. One of the promising alternative fuels that can be used as a clean highefficiency compression ignition...
-
The Application of Satellite Image Analysis in Oil Spill Detection
PublikacjaIn recent years, there has been an increasing use of satellite sensors to detect and track oil spills. The satellite bands, namely visible, short, medium infrared, and microwave radar bands, are used for this purpose. The use of satellite images is extremely valuable for oil spill analysis. With satellite images, we can identify the source of leakage and assess the extent of potential damage. However, it is not yet clear how to...
-
NON-LINE ANALYSIS OF STIFFNESS IN COMPRESSION CONDITIONS
PublikacjaThe analyzes were aimed at demonstrating the influence of parameters describing the deformation of the structure on the uncertainty of critical force, and the impact of technological imperfections on stress uncertainty in compression conditions. In a linear buckling analysis, the problem is considered only for the initial, permanent state of the stiffness matrix. In the case of demonstrating the influence of initial deformations...
-
The flux compression generator load parameters selection
PublikacjaComputer simulation results of the flux compression generator (FCG) loaded with an inductor has been presented in this paper. Simulation research has been performed in order to select the parameters of FCG load coil properly. The influence of the load inductance and resistance on the current gain factor and the magnetic field energy accumulated in a load coil has been investigated.
-
The Analysis of Overall Ship Fuel Consumption in Acceleration Manoeuvre using Hull-Propeller-Engine Interaction Principles and Governor Features
PublikacjaThe problem of reduction of greenhouse gas emissions in shipping is currently addressed by many research works and related industries. There are many existing and visionary technologies and ideas, which are conceptually defined or practically realised. This goal can be achieved in different ways, and reducing fuel consumption is one of the major methods. In these circumstances, the aim of this study is to analyse the possibility...
-
Co-gasification of waste biomass-low grade coal mix using downdraft gasifier coupled with dual-fuel engine system: Multi-objective optimization with hybrid approach using RSM and Grey Wolf Optimizer
PublikacjaThe looming global crisis over increasing greenhouse gases and rapid depletion of fossil fuels are the motivation factors for researchers to search for alternative fuels. There is a need for more sustainable and less polluting fuels for internal combustion engines. Biomass offers significant potential as a feed material for gasification to produce gaseous fuel. It is carbon neutral, versatile, and abundant on earth. The present...
-
Reduction of CO2 Emissions from Offshore Combined Cycle Diesel Engine-Steam Turbine Power Plant Powered by Alternative Fuels
PublikacjaDiverse forms of environmental pollution arise with the introduction of materials or energy that exert adverse effects on human health, climate patterns, ecosystems, and beyond. Rigorous emission regulations for gases resulting from fuel combustion are being enforced by the European Union and the International Maritime Organization (IMO), directed at maritime sectors to mitigate emissions of SOx, NOx, and CO2. The IMO envisions...
-
Surface-dependent biological potential of spherical silver nanoparticles
Dane BadawczeThe growing interest in silver nanoparticles (AgNPs) is largely driven by their significant antimicrobial potential. As carriers of reactive silver ions on a nanoscale, AgNPs are considered excellent candidates for specific antibacterial strategies. Numerous scientific studies have highlighted that AgNPs are broad-spectrum antimicrobials, with their...
-
Release Kinetics Studies of Early-Stage Volatile Secondary Oxidation Products of Rapeseed Oil Emitted during the Deep-Frying Process
PublikacjaThe research concerns the use of proton transfer reaction mass spectrometer to track real-time emissions of volatile secondary oxidation products released from rapeseed oil as a result of deep-frying of potato cubes. Therefore, it was possible to observe a sudden increase of volatile organic compound (VOC) emissions caused by immersion of the food, accompanied by a sudden release of steam from a potato cube and a decrease of the...
-
EXHAUST TEMPERATURE MEASUREMENTS OF THE MARINE TURBOCHARGED DIESEL ENGINES IN OPERATION
PublikacjaThe article presents the selected metrology issues concerning the exhaust temperature of the turbocharged marine engines during operation. The special concern has been paid on existing disturbances as well as thermodynamical interpretation of the recorded measurement signal. A diagnostic informativeness of the standard exhaust temperature’s measurements has worked out while the engine runs in steady states has been also considered...
-
STUDY OF SEASONAL ACOUSTIC PROPERTIES OF SEA WATER IN SELECTED WATERS OF THE SOUTHERN BALTIC
PublikacjaClimate Research of the globe is a current task, in particular to confirm the general hypothesis of global warming associated with an increase in average temperature. The sea acoustic climate is derived from the concept of climate and refers to the conditions of propagation of acoustic waves in a particular basin. In this paper, the results of systematic measurements of temperature, salinity and velocity distributions of sound...
-
The impact of bankruptcy regimes on entrepreneurship and innovation. Is there any relationship?
PublikacjaThe literature review indicates that bankruptcy law may play an important role in and be one of the factors infuencing the development of entrepreneurship, innovation, and thus economic growth, among other things. In previous studies, the analysis of the impact of bankruptcy law on individual variables has been conducted independently. Our aim was to conduct a holistic analysis, taking several factors into account simultaneously....
-
Status report on high temperature fuel cells in Poland – Recent advances and achievements
PublikacjaThe paper presents recent advances in Poland in the field of high temperature fuel cells. The achievements in the materials development, manufacturing of advanced cells, new fabrication techniques, modified electrodes and electrolytes and applications are presented. The work of the Polish teams active in the field of solid oxide fuel cells (SOFC) and molten carbonate fuel cell (MCFC) is presented and discussed. The review is oriented...
-
POLAND’S ENERGY DEPENDENCE AT THE TURN OF THE 21ST CENTURY
PublikacjaThe following article is an attempt to assess Poland's energy independence in the years 1993-2020. The main aim of the paper is to present Poland's dependence on raw materials from foreign partners - in the field of imports of electricity, natural gas, crude oil, non-renewable energy resources, i.e., hard coal and lignite, and the country's dynamics in the amount of imports. In addition, the aim of the work is to answer research...
-
Sustainable energy consumption – Empirical evidence of a household in Poland
PublikacjaThere is an expected increase in the demand for electricity from households in European countries. The outcome of the growing proportion of renewable energy sources in the energy supply mix should result in improved customer awareness regarding their electricity usage. Additionally, they must assume a more proactive role in overseeing their electricity usage. Innovation and pollution management have become crucial catalysts for...
-
Application of Thermo-chemical Technologies for Conversion of Associated Gas in Diesel-Gas Turbine Installations for Oil and Gas Floating Units
PublikacjaThe paper considers the issue of thermo-chemical recovery of engine’s waste heat and its further use for steam conversion of the associated gas for oil and gas floating units. The characteristics of the associated gas are presented, and problems of its application in dual-fuel medium-speed internal combustion engines are discussed. Various variants of combined diesel-gas turbine power plant with thermo-chemical heat recovery are...
-
Towards a modification of a regulatory framework aiming at bunker oil spill prevention from ships - A design aspect of bunker tanks vents location guided by CFD simulations
PublikacjaAlthough accidental bunker oil spills at seaway are relatively rare events, they can be pose real threat to the natural marine environment. One of the reasons for the bunker spill to occur is a design failure; one of the ways it can demonstrate is an improper location or height of vent heads, leading to a bunker oil discharge during heavy rolling, due to sloshing phenomenon. Design of a ship and her systems is guided by various...
-
Analysis of different tillage implements with respect to reduced fuel consumption, tractor operating speed and its wheel slippage
PublikacjaNowadays the prices of agricultural farm produced products are increasing with ant-speed and the prices of input for raising crops are increasing with rocket-speed. Therefore, there is a dire need to conduct some important studies to innovate the techniques which can lower the costs of crop production. In this context, this study was conducted to evaluate the consumption of fuel at different tillage implements, tractor operating...
-
Investigations of the Working Process in a Dual-Fuel Low-Emission Combustion Chamber for an FPSO Gas Turbine Engine
PublikacjaThis investigation is devoted to an analysis of the working process in a dual-fuel low-emission combustion chamber for a floating vessel’s gas turbine. The low-emission gas turbine combustion chamber with partial pre-mixing of fuel and air inside the outer and inner radial-axial swirlers was chosen as the object of research. When modelling processes in a dual-flow low-emission gas turbine combustion chamber, a generalized method...
-
Aneta Sobiechowska-Ziegert dr
OsobyPracuje w Katedrze Statystyki i Ekonometrii na Wydziale Zarządzania i Ekonomii, pasjonatka stosowania nowoczesnych metod dydaktycznych w nauczaniu przedmiotów ilościowych, dyplomowany coach i certyfikowana tutorka. Prowadzi zajęcia z prognozowania gospodarczego i ekonometrii przestrzennej. Przewodniczy Wydziałowej Komisji Jakości Kształcenia i opiekuje się ścieżką kształcenia EMOS, certyfikowaną przez Eurostat. Obecnie koordynuje...
-
Effect of presence of lifting pocket on the THD performance of a large tilting-pad thrust bearing
PublikacjaHydrostatic assistance is a commonly used method to improve limited load carrying ability of tiltingpad thrust bearings during transient states of operation of vertical shaft hydro-generators. Despite of special hydraulic equipment (as pumps, valves, etc.), it also requires manufacturing of special recesses/pockets at pad sliding surfaces, into which oil is injected under high pressure. It allows to lift the rotor before start-up...
-
CLAY MINERALS – MINERALOGY AND PHENOMENON OF CLAY SWELLING IN OIL & GAS INDUSTRY
PublikacjaAmong the minerals found in the earth's crust, clay minerals are of the widest interest. Due to the specific properties such as plasticity, absorbing and catalytic properties clay minerals are used in many industries (oil & gas, chemistry, pharmacy, refractory technology, ceramics etc.). In drilling, a phenomenon of swelling clays is frequently observed. It has an important impact on the cementing quality. During the last few decades...
-
Environmentally acceptable lubricants (EAL) compared with a reference mineral oil as marine stern tube bearing lubricant – Experimental and theoretical investigations
PublikacjaThe purpose of this research is to indicate the potential differences in bearing characteristics resulting from the application of different lubricant types with the same viscosity grade. The effect of different environmentally acceptable lubricants (EALs) on hydrodynamic journal bearing properties is studied experimentally and compared to the properties obtained after lubrication with a reference mineral oil. The results of the...
-
Household Ability of Expenditures on Electricity and Energy Resources in the Countries That Joined the EU after 2004
PublikacjaThe purpose of the following article is to present the situation of the energy market from a household perspective between 2010 and 2020 in selected EU countries (the group of member states which joined EU after 2004). The selected countries when joining the EU had similar economic indicators and to some extent were similar in other macro-economic situations (personal income, unemployment rate, GDP level and annual growth). This...
-
Jarosław Gawdzik Ph.D.
OsobyDiplomas and degrees obtained: a) 21 Sept. 1990 – MSc. Eng. – Cracow University of Technology Title of the MA thesis: Numerical method of catalyst deactivation computation (in Polish) Su-pervisor: Associated Prof. Wanda Kramarz, PhD, Eng. b) 24 Oct. 2001 – Doctor of technical sciences, Faculty of Civil Engineering, Kielce University of Technology. Title of the doctoral dissertation: Investigations into oil derivative migration...
-
Te use of acoustic emission for assessment of the oil lubricity in a four-ball tester
Publikacjain view of the increased dynamic and temperature load in the compression-ignition engine tribological systems, particular attention is drawn to the problem of such lubrication of the friction nodes that after breaking the boundary layer it could be restored without any wear occurring. therefore, an idea has been devised of introducing to friction nodes, with the lubrication oils, of new substances (operational preparations) modifying...
-
settingsOrder Article Reprints This is an early access version, the complete PDF, HTML, and XML versions will be available soon. Open AccessArticle Investigation of the Frying Fume Composition During Deep Frying of Tempeh Using GC-MS and PTR-MS
PublikacjaThis study employed proton transfer reaction mass spectrometry (PTR-MS) and gas chromatography–mass spectrometry (GC-MS) to identify and monitor volatile organic compounds (VOCs) in frying fumes generated during the deep frying of tempeh. The research aimed to assess the impact of frying conditions, including frying temperature, oil type, and repeated use cycles, on the formation of thermal decomposition products. A total of 78...
-
Towards Use of OntoClean for Ontology Contextualization
PublikacjaOntologies are formal systems of concepts used to describe numerous domains of interest. Ontologies are usually very expressive, but it comes at a price of computationally expensive reasoning over them. In our previous work we discussed the possible performance benefits that can be obtained by decomposing an ontology into contexts. While the benefits are appealing, we discovered that, in our case, the main obstacle against using...
-
A distillery by-product as an external carbon source for enhancing denitrification in mainstream and sidestream treatment processes
PublikacjaThe use of fusel oil as an 'alternative' carbon source for denitrification in the mainstream and sidestream treatment processes was studied. Research comprised two kinds of batch experiments as well as acclimation of process biomass to external carbon sources. In the conventional nitrate utilization rate (NUR) measurements (one-phase experiments with non-acclimated biomass), the NUR with fusel oil was 1.4-1.7 g N/(kg VSS•h which...
-
Stability of an Innovative Cold-Formed GEB Section
PublikacjaThis paper is focused on the numerical analysis and experimental test of stability of the cold-formed profile with an innovative GEB cross-section. For the shell model of the axially compressed member, the linear buckling analysis and the nonlinear static analysis were carried out. In the numerical research, the buckling load and the limit load for variable section heights were obtained. Some of the results were compared with the...
-
Analiza numeryczna i badania doświadczalne wpływu usytuowania stężeń na nośność wyboczeniową modelu kratownicy
PublikacjaIn the present research the results of experimental test and numerical analyses of a model of a typical truss are presented. The truss linear buckling analysis and non linear static analyses with respect to material and geometrical nonlinearity are conducted. For different stiffnesses and location of braces, the critical load and limit load for the truss are calculated and the threshold bracing stiffness is found. The results of...
-
Thermal utilization of meat-and-bone meal using the rotary kiln pyrolyzer and the fluidized bed boiler – The performance of pilot-scale installation
PublikacjaThermal utilization of meat-and-bone meal (MBM) is subject to stringent regulations that are meant to provide elimination of any potential pathogens. Incineration as well as other possible routes for thermal conversion of MBM are still at the research state. The universal technology was developed that allows to combust various types of waste organic materials, including animal waste, municipal solid waste and sludge, mixed at any...