Wyniki wyszukiwania dla: titanium%20alloys
-
Cavitation erosion of some alloys manufactured on steel and iron surfaces by laser beam.
PublikacjaPrzedstawiono badania odporności kawitacyjnej stali węglowej 45 odpornej na korozję 2H13 i technicznego żelaza po ich obróbce laserowej. Warstwę wierzchnią wybranych stali wzbogacono w różne pierwiastki stopowe i badano odporność kawitacyjną na stanowisku z wirującą tarczą. Stwierdzono niską odporność kawitacyjną dla warstw o obniżonej zdolności do utwardzania pod wpływem obciążeń kawitacyjnych oraz silną zależność odporności...
-
Cavitation erosion of some laser-produced iron-base corrosion-resistance alloys
PublikacjaW pracy przedstawiono badania kawitacyjne stali C45, X20Cr13 oraz X5CrNi18-10 po laserowym stopowaniu ich warstwy wierzchniej proszkami Mn, Cr, Ni, Si, Ti, Co, Al, Mo, B. Badania kawitacyjne prowadzono na stanowisku z wirującą tarczą. Zniszczenia powierzchni w okresie inkubacji oceniano metodą optyczną. Przedstawiono związek pomiędzy uzyskaną mikrostrukturą obrabianej warstwy i jej odpornością kawitacyjną.
-
Long-term researches of stress corrosion cracking of Al-Zn-Mg alloys
PublikacjaPraca przedstawia wyniki odporności na korozję naprężeniową stopów Al-Zn-Mg uzyskane w warunkach stacjonarnych. Dodatkowo określono wpływ składu chemicznego oraz obróbki cieplnej na odporność korozyjną tych stopów. Badania prowadzono w 3% NaCl w warunkach stałego obciążenia σ = 0.8R0.2 przez 1500 godzin. Stwierdzono, iż zawartość Zn i Mg oraz szybkość chłodzenia to główne czynniki wpływające na podatność tych stopów na korozje...
-
Pre-oxidation of porous ferritic Fe22Cr alloys for lifespan extension at high-temperature
PublikacjaPre-oxidation of porous ferritic Fe22Cr alloys was extensively studied in this paper. Weight gain measurements and SEM analysis revealed that pre-oxidation performed at 900◦C for 40 min increased the lifespan of the alloy. A Cr evaporation study did not disclose any significant influence of the pre-oxidation process on the Cr content in the alloy. For a more detailed assessment, TEM imaging and X-ray tomography measurements of...
-
Relationship between cavitation resistance of laser produced alloys and their ability to work hardening
PublikacjaBadano odporność kawitacyjną laserowo wytworzonych stopów na stalach konstrukcyjnych i ich związek ze zdolnością do umacniania się pod wpływem działania obciążeń kawitacyjnych. Wykazano, że mikrotwardość powierzchni wykazuje monotoniczną zależność z odpornością kawitacyjną i zdolnością do umacniania.
-
Quadratic Cohen representations in spectral analysis of serration process in Al-Mg alloys
PublikacjaIstotny z mechanicznego punktu widzenia efekt Portevina Le-Chateliera charakteryzuje się skomplikowanym profilem widmowym. Jako typowy przykład procesu niestacjonarnego, wymaga specjalnego podejścia umożliwiającego analizę zmian rozkładu energii fluktuacji naprężenia w funkcji odkształcenia. Jako narzędzie umożliwiające realizację powyższego założenia autorzy proponują zastosowanie rodziny przekształceń kwadratowych znanych jako...
-
Wear and corrosion characteristics of the layers type (mn-p) formed on aluminium alloys
Publikacjaopisano multipleksową metodę wytwarzania warstw zawierających mangan i fosfor (mn-p) na stopach aluminium. przedstawiono wyniki badań mikrostruktury, właściwości tribologicznych i korozyjnych tych warstw. stwierdzono obecność tlenku manganu i fosforku manganu w wytworzonych warstwach oraz ich wysoką twardość, rzędu 1272 hv0,02. warstwy typu (mn-p) zmniejszają podatność stopu alsi13mg1cuni na korozję w 0,01 mh2so4.
-
Quadratic Cohen representations in spectral analysis of serration process in Al–Mg alloys
PublikacjaImportant from mechanical point of view the Portevin–Le Chatelier serration phenomenon is being characterized by a complicated spectral profile. As a typical example of nonstationary processes it demands a special treatment allowing to follow the evolution of energy of stress fluctuations as a function of strain. The authors suggest the utilization of a compact system of quadratic transformations, known as Cohen class, as a technique...
-
Effect of native air-formed oxidation on the corrosion behavior of AA7075 aluminum alloys
PublikacjaThe microstructure of aluminum alloys plays a key role in their corrosion resistance. In particular, the presence of intermetallic precipitates differing in the potential from the alloy matrix induces local corrosion. The study presents the effect of native air-formed oxidation on the corrosion behavior of AA 7075 aluminum alloy. Various microscopic and spectroscopic techniques were used to examine the changes occurring in the...
-
Influence of laser remelting at cryogenic conditions on corrosion resistance of non-ferrous alloys
PublikacjaCelem nadtapiania laserowego elementów wytwarzanych z stopów aluminium, miedzi i tytanu jest uzyskanie wysokiej twadrości i odporności na korozję dla wydłużenia okresu ich eksploatacji w rezultacie ich szybkiej krystalizacji. Końcowa mikrostruktura, skład fazowy i właściwości wymienionych stopów zależą od parametrów obróbki laserowej oraz budowy wykresów równowagi fazowej. W artykule przedstawiono wpływ laserowego nadtapiania...
-
High temperature oxidation of porous alloys for solid oxide fuel cell applications
PublikacjaW pracy proszki PI600, 317L i 430L stali użyto do przygotowania porowatych metalowych podłoży dla tlenkowych ogniw paliwowych. Po spiekaniu w różnych temperaturach oceniana była ich porowatość i wysokotemperaturową odporność na korozję. Cykliczna analiza termograwimetryczna, dyfraktometria rentgenowska i obrazów SEM były używane do opisu właściwości tych porowatych stopów. Właściwości elektryczne badano dla wybranych próbek. Wpływ...
-
Advancements in the Additive Manufacturing of Magnesium and Aluminum Alloys through Laser-Based Approach
PublikacjaComplex structures can now be manufactured easily utilizing AM technologies to meet the pre-requisite objectives such as reduced part numbers, greater functionality, and lightweight, among others. Polymers, metals, and ceramics are the few materials that can be used in AM technology, but metallic materials (Magnesium and Aluminum) are attracting more attention from the research and industrial point of view. Understanding the role...
-
X-ray Photoelectron Spectroscopy of Carboxylic Acids as Corrosion Inhibitors of Aluminium Alloys
PublikacjaThe datasets, titled X-ray Photoelectron Spectroscopy studies of citric acid adsorption on aluminium alloy 5754 in alkaline media and X-ray Photoelectron Spectroscopy studies of various carboxylic acids adsorption on aluminium alloys in alkaline media, contain XPS studies of the corrosion inhibitory action of selected dicarboxylic acids towards commercially available aluminium alloy 5754 in alkaline media at pH=11. These datasets...
-
Comparison of corrosion resistance of al-alloys by means of dynamic electrochemical impedance spectroscopy
PublikacjaPrzeprowadzono badania metodą dynamicznej elektrochemicznej spektroskopii impedancyjne stopów 1100 i 5162. Zaproponowano zastępcze modele elektryczne opisujące zachowanie się stopów w warunkach ekspozycji w roztworach zawierających wysokie stężenie jonów chlorkowych. Wyznaczono zmiany podstawowych parametrów elektrycznych układów zastępczych od potencjału. Stwierdzono wyższą podatność na korozję stopu 5162 w porównaniu ze stopem...
-
Anna Zielińska-Jurek prof. dr hab. inż.
OsobyResearch work on photocatalysis by Prof. Anna Zielinska-Jurek started in 2006 at Gdansk University of Technology (Poland), including 3-month research stay at Hokkaido University, Training School “Environmental Applications of TiO2 Photocatalysis” at the University of Oulu in Finland granted by COST Program and Training School “NanoBiophotonics” at the Beckmann Institute, Urbana-Champaign in the USA granted by University of Illinois....
-
Photocatalytic Water Disinfection under Solar Irradiation by d-Glucose-Modified Titania
Publikacja -
A new method for preparation of rutile phase titania photoactive under visible light
Publikacja -
The interaction of the pulsed laser irradiation with titania nanotubes - Theoretical studies on the thermal effect
PublikacjaThis paper reports temperature dispersion simulations of titania nanotubes irradiated by the 355 nm, pulsed, nanosecond laser. The modelling with the use of Finite Elements Method concerns titania nanotubes of the length and the wall thickness in the range of 0.5–2 μm and 5–20 nm, respectively. The uniqueness of the morphology was preserved by ensuring the wall thickness variation along the height of the tube, which was determined...
-
Review on robust laser light interaction with titania – Patterning, crystallisation and ablation processes
PublikacjaTitanium dioxide is regarded as a very promising semiconducting material that is widely applied in many everyday-use products, devices, and processes. In general, those applications can be divided into energy or environmental categories, where a high conversion rate, and energy and power density are of particular interest. Therefore, many efforts are being put towards the elaboration of novel production routes, and improving the...
-
SEM-EDS images of expanded polystyrene spheres coated with silicon dioxide (SiO2) and/or titanium dioxide (TiO2)
Dane BadawczeData contain SEM and SEM-EDS images of expanded polystyrene spheres coated with silicon dioxide (SiO2) and/or titanium dioxide (TiO2). The detailed equipment and measurement data was described in measurement info.txt file.
-
XPS (X-ray photoelectron spectroscopy) of titanium dioxide coated nickel foams and heated 400,500, 600C
Dane BadawczeThis data set contains XPS spectra recorded for nickel foams coated with titanium dioxide and heated at 400, 500 and 600 degrees celcius.
-
Gas‐Phase Removal of Indoor Volatile Organic Compounds and Airborne Microorganisms Over Mono‐ and Bimetal‐Modified (Pt, Cu, Ag) Titanium(IV) Oxide Nanocomposites
PublikacjaThe photocatalytic deactivation of volatile organic compounds and mold fungi using TiO2 modified with mono‐ and bimetallic (Pt, Cu, Ag) particles is reported in this study. The mono‐ and bimetal‐modified (Pt, Cu, Ag) titanium(IV) oxide photocatalysts were prepared by chemical reduction method and characterized using XRD, XPS, DR/UV‐Vis, BET and TEM analysis. The effect of incident light, type and content of mono‐ and bimetallic...
-
How Do Ionic Liquids Affect the Surface Structure of Titania Photocatalyst? An Electron-Trap Distribution-Analysis Study
PublikacjaTitanium(IV) oxide, titania, photocatalyst particles were prepared from titanium alkoxide in the presence of several kinds of ionic liquids, and it was clarified that a group of samples exhibited photocatalytic activity for phenol degradation under the irradiation of light of wavelength >400 nm higher than those of the other group of samples. Although the conventional structural analytical results could not be related to the activity,...
-
Electrophoretic deposition and characterization of composite chitosan/Eudragit E 100 or poly(4-vinylpyridine)/mesoporous bioactive glass nanoparticles coatings on pre-treated titanium for implant applications
PublikacjaTitanium implants are surface-modified to achieve bioactivity and often antibacterial properties. Such surface coatings may increase corrosion degradation and be weakly attached to the substrate. In the present research, biodegradable composite coatings, investigated so far as smart environment-sensitive, slowly releasing silver to the implant neighborhood, were produced as a combination of chitosan (CS) with Eudragit E 100 (EE100)...
-
Corrosion resistance evaluation of Al‐based alloys by means of dynamic electrochemical impedance spectroscopy
Publikacja -
Effect of native air-formed oxidation on the corrosion behavior of AA 7075 aluminum alloys
Publikacja -
Identification of Bodner-Partom Viscoplastic Model Parameters for Some Aluminum Alloys at Elevated Temperature
PublikacjaThe paper presents the identification process of inelastic (viscoplastic) properties for two aluminum alloys at a temperature of 120°C. The material parameters are calculated on the basis of uniaxial tension tests. Twelve tests at elevated temperature for each alloy have been performed—three tests for four different strain rates. The main purpose of the paper is to identify the Bodner-Partom viscoplastic model parameters for two...
-
Evaluation of the Microstructure and Magnetic Properties of Fe73Me5Y3B19 (Where Me = Ti or Nb) Amorphous Alloys
Publikacja -
The present state of requirements of international association of classification societies (IACS) for wrought aluminium alloys
PublikacjaW referacie przedstawiono aktualną sytuację w zakresie stopów aluminium z serii 5xxx i 6xxx do przeróbki plastycznej, ze szczególnym uwzględnieniem zmian w tym zakresie zapoczątkowanych przez unifikację wymagań w dokumentach nr 25 i 26 opublikowanychostatnio przez International Association of Classification Societies (IACS). Jednym z najważniejszych punktów w tych dokumentach jest wymaganie odnośnie przeprowadzania próby odporności...
-
Corrosion resistance evaluation of Al-based alloys by means of dynamic electrochemical impedance spectroscopy
PublikacjaW pracy przedstawiono wyniki badań stopów aluminium wykonane za pomocą dynamicznej elektrochemicznej spektroskopii. Na podstawie uzyskanych widm impedancyjnych zostały pokazane zmiany parametrów elektrycznego schematu zastępczego z potencjałem. Stwierdzono, że dodatek magnezu do badanego stopu obniża właściwości przeciwkorozyjne stopu.
-
Influence of friction stir welding technological parameters on the properties of the joints of selected aluminum alloys
PublikacjaThe purpose of this dissertation was to determine the effect of friction stir welding technological parameters on the properties of selected aluminum alloy joints, with consideration of the residual stresses and dislocation density in the joints. The goal of the present work was also to produce defect-free joints with high mechanical and electrochemical properties. In the dissertation, similar welds of AA6082 alloy and dissimilar...
-
Characteristics of the (Mn-N-O-P) type layers created on the cast aluminium alloys
PublikacjaPrzedstawiono skład chemiczny i fazowy, a także właściwości korozyjne i tribologiczne warstw powierzchniowych typu (Mn-N-O-P) wytworzonych na odlewniczych stopach aluminium. Warstwy typu (Mn-N-O-P) wielokrotnie podnoszą zarówno właściwości tribologiczne jak i korozyjne odlewniczych stopów aluminium z krzemem.
-
Application and modelling of Shape-Memory Alloys for structural vibration control: State-of-the-art review
PublikacjaOne of the most essential components of structural design for civil engineers is to build a system that is resistant to environmental conditions such as harsh chemical environments, and catastrophic disasters like earthquakes and hurricanes. Under these circumstances and disturbances, conventional building materials such as steel and concrete may demonstrate inadequate performance in the form of corrosion, deterioration, oxidizing,...
-
Effect of MAO coatings on cavitation erosion and tribological properties of 5056 and 7075 aluminum alloys
PublikacjaTwo ceramic coatings have been applied on 5056 and 7075 aluminum alloy by microarc oxidation (MAO) technology. The mass losses, surface morphologies and the phase constituents of the MAO coatings before and after cavitation tests were examined by means of digital scales, scanning electron microscopy (SEM) and X-ray diffraction (XRD), respectively. In order to assess the impact of the mechanical properties of the surface layer on...
-
Measurement of temperature-dependent viscosity and thermal conductivity of alumina and titania thermal oil nanofluids
PublikacjaThe results of simultaneous measurements of dynamic viscosity, thermal conductivity, electrical conductivity and pH of two nanofluids, i.e. thermal oil/Al2O3 and thermal oil/TiO2 are presented. Thermal oil was selected as a base liquid because of possible application in ORC systems as an intermediate heating agent. Nanoparticles were tested at the concentration of 0.1%, 1% and 5% by weight within temperature range from 20°C to...
-
MEASUREMENT OF TEMPERATURE-DEPENDENT VISCOSITY AND THERMAL CONDUCTIVITY OF ALUMINA AND TITANIA THERMAL OIL NANOFLUIDS
PublikacjaIn this study results of simultaneous measurements of dynamic viscosity, thermal conductivity, electrical conductivity and pH of two nanofluids, i.e. thermal oil/Al2O3 and thermal oil/TiO2 are presented. Thermal oil is selected as a base liquid because of possible application in ORC systems as an intermediate heating agent. Nanoparticles were tested at the concentration of 0.1%, 1% and 5% by weight within temperature range from...
-
Bactericidal Properties of Plasmonic Photocatalysts Composed of Noble Metal Nanoparticles on Faceted Anatase Titania
Publikacja -
Antimicrobial properties of pristine and Pt-modified titania P25 in rotating magnetic field conditions
Publikacja -
Visible-light-induced photocatalysis through surface Plasmon excitation of gold on titania surfaces
PublikacjaPietnascie komercyjnych probek tlenku tytanu(IV) zostalo zmodyfikowanych zlotem za pomoca fotodepozycji oraz scharakteryzowanych. Fotoaktywnosci proszkow Au/TiO2 zostaly przebadane dla fotodegradacji kwasu octowego i 2-propanolu podczas naswietlania promieniowaniem widzialnym oraz ultrafioletowym. Wykazano, ze fotokatalityczne aktywnosci scisle zaleza od wlasciwosci nanoczastek zlota i tlenku tytanu. Analizy spektrum działania...
-
Novel nitrogen precursors for electrochemically driven doping of titania nanotubes exhibiting enhanced photoactivity
PublikacjaNitrogen doped titania nanotubes were successfully sensitized by electrochemical method, i.e. as-anodized titania was immersed in different amine (diethyleneamine-DETA, triethyleneamine-TEA, ethylenediamine-EDA) and urea (U) solution and a constant potential was applied. The highly ordered morphology of fabricated N-TiO2 was investigated by using scanning electron microscopy. Spectroscopic techniques, i.e. UV-Vis spectroscopy,...
-
The new method of ZnIn2S4 synthesis on the titania nanotubes substrate with enhanced stability and photoelectrochemical performance
PublikacjaThe new method of ZnIn2S4 synthesis on the titania nanotubes substrate with enhanced stability and photoelectrochemical performance
-
The impact of environmental water on the potential application of core−shell titania−silica nanospheres as photocatalysts
Publikacja -
Porous silica matrix as an efficient strategy to boosted photocatalytic performance of titania/carbon composite
Publikacja -
Optimization of electrochemical doping approach resulting in highly photoactive iodine-doped titania nanotubes
PublikacjaThe paper focuses on the optimization procedure concerning the synthesis method resulting in highly ordered titania nanotubes doped with iodine atoms. The doping process was based on the electrochemical treatment of a titania nanotube layer immersed in a potassium iodide (KI) solution acting as an iodine precursor. A number of endeavors were undertaken in order to optimize the doping conditions. Electrolyte concentration, reaction...
-
The geometry of free-standing titania nanotubes as a critical factor controlling their optical and photoelectrochemical performance
PublikacjaTitanium dioxide nanotubes are regarded as one of the most important functional materials and due to their unique electronic properties, chemical stability and photocorrosion resistance, they find applications in, for example, highly efficient photocatalysis or perovskite solar cells. Nevertheless, modification of TiO2 nanotubes is required to overcome their main drawback, i.e. large energy bandgap (>3.2 eV) limiting their ability...
-
Allergic reactions as a defense of the organism to the influence of implants components made of stainless steel
PublikacjaDue to the increasing number of cases of hypersensitivity caused by direct contact with metals, as well as the increasing demand for implants in humans all ages numerous studies on the effects of the impact of implant components are being carried out. The paper presents the phenomenon of etiology of allergy in general terms and in relation to the biomaterials used in medicine. There have been characterized in terms of impact on...
-
Allergic Reactions as a Defense of the Organism to the Influence of Implants Components Made of Stainless Steel
PublikacjaDue to the increasing number of cases of hypersensitivity caused by direct contact with metals, as well as the increasing demand for implants in humans all ages numerous studies on the effects of the impact of implant components are being carried out. The paper presents the phenomenon of etiology of allergy in general terms and in relation to the biomaterials used in medicine. There have been characterized in terms of impact on...
-
Fabrication and Significant Photoelectrochemical Activity of Titania Nanotubes Modified with Thin Indium Tin Oxide Film
PublikacjaOrdered titanium dioxide nanotubes (TiO2NTs) modified with indium tin oxide (ITO) films were obtained via magnetron sputtering, in which ITO plate was used as a target, onto the as-anodized titania support followed by the calcination process. The morphology of fabricated material with deposited oxide was investigated using scanning electron microscopy. Raman and UV–Vis spectroscopies were utilized to characterize crystalline phase...
-
Titania Nanotubes/Hydroxyapatite Nanocomposites Produced with the Use of the Atomic Layer Deposition Technique: Estimation of Bioactivity and Nanomechanical Properties
PublikacjaTitanium dioxide nanotubes/hydroxyapatite nanocomposites were produced on a titanium alloy (Ti6Al4V/TNT/HA) and studied as a biocompatible coating for an implant surface modification. As a novel approach for this type of nanocomposite fabrication, the atomic layer deposition (ALD) method with an extremely low number of cycles was used to enrich titania nanotubes (TNT) with a very thin hydroxyapatite coating. X-ray diffraction (XRD)...
-
Photocatalytic decomposition of acetaldehyde over TiO2 (titanium dioxide) supported on nickel foam and Ni-doped (nickel-doped) TiO2
Dane BadawczeThis dataset contains chromatograms recorded during the decomposition of acetaldehyde in a high-temperature reaction chamber under UV irradiation using as photocatalytic systems TiO2 (titanium dioxide) supported on nickel foam, TiO2 supported on oxidized nickel foam and TiO2 doped by metallic nickel (Ni) powder. The detailed equipment and measurement...