Wyszukiwarka
Filtry
wszystkich: 5419
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: , thermal jump conditions.
-
On jump conditions at non-material singular curves in the resultant shell thermomechanics
PublikacjaThe global, refined, resultant, two-dimensional (2D) balance laws of mass, linear and angular momenta, and energy as well as the entropy inequality were formulated by Pietraszkiewicz (2011) as exact implications of corresponding laws of 3D rational thermomechanics. In case of a shell with the regular base surface and all resultant surface fields differentiable everywhere on it and at any time instant, the local laws of the resultant...
-
Influence of preparation conditions on thermal properties of lanthanide benzenepolycarboxylates
Publikacja -
Evaluation of Respiration Rate Using Thermal Imaging in Mobile Conditions
PublikacjaRespiratory rate is very important vital sign that should be measured and documented in many medical situations. The remote measurement of respiration rate can be especially valuable for medical screening purposes (e.g. severe acute respiratory syndrome (SARS), pandemic influenza, etc.). In this chapter we present a review of many different studies focused on the measurements and estimation of respiration rate using thermal imaging...
-
Influence of type of material on performance of hydraulic components in thermal shock conditions
PublikacjaDuring the start-up of a hydraulic system in low ambient temperatures an incorrect operation may occur. The principles and conditions of safely operating hydraulic driven machines and devices are essential to designers and operators. For this reason the author of this article has conducted a series of tests on hydraulic components and systems in thermal shock conditions (cooled-down components were supplied with hot working medium)....
-
Thermal boundary conditions to simulate friction layers and coatings at sliding contacts
PublikacjaA brief review of the thermal boundary conditions specified at sliding interfaces was performed. New thermal boundary conditions were derived aimed at solving problems of sliding with account of surface layers representing friction layers and tribological coatings. Based on the assumption of linear temperature distributions in the surface layers, the proposed conditions enable one to simplify simulations by eliminating the surface...
-
New components for hydraulic drive systems and their performance in thermal shock conditions
PublikacjaArtykuł prezentuje konstrukcję pomp z rozrządem krzywkowym typu PWK o zmiennej wydajności wraz ze wstępnymi wynikami badań prototypu PWKZ-78. Przedstawiono także wstępne wyniki analiz MES i CFD zjawisk zachodzących w pracującej pompie. W drugiej części zaprezentowano metodykę badań zachowania się pomp w warunkach szokutermicznego i wyniki uzyskane dla pompy typu PWK.
-
The influence of thermal conditions on V2O5 nanostructures prepared by sol-gel method
PublikacjaThis work presents the result of structure investigations ofV 2O5 nanorods grown from thin films and powders prepared by sol-gel method. To examine the best temperature of nanorods crystallization, thin films deposited by spin-coating method on quartz glass or silicon substrates and bulk xerogel powders were annealed at various temperatures ranging from 100∘C to 600∘C. The structure of the samples was characterized by X-ray diffraction...
-
Thermal performance of a prototype plate heat exchanger with minichannels under boiling conditions
PublikacjaTo solve the problem and to meet the requirements of customers in the field of high heat fluxes transfer in compact units, a new design of plate heat exchanger with minichannels (minichannels PHE) was proposed. The aim was to construct a compact heat exchanger of high effectiveness for the purpose of household cogeneration ORC system. In this paper the experimental analysis of an assembled prototype of such compact heat exchanger...
-
Evaluation of fire hazard in electrical installations due to unfavorable ambient thermal conditions
PublikacjaEvaluation of fire hazard caused by electrical installations is a difficult and important topic, and it limits the possibility of loss of life or health of people, as well as the occurrence of significant property damage. In particular, this hazard was caused by power cables and especially photovoltaic (PV) installations. The authors proved that power cables directly exposed to strong solar radiation are likely to exceed maximum...
-
Evaluation of Fire Hazard in Electrical Installations Due to Unfavorable Ambient Thermal Conditions
Publikacja -
Analysis of the Heating Process of Hydraulic Motors during Start-Up in Thermal Shock Conditions
PublikacjaConditions that prevail during harsh winters and hot summers pose a serious challenge for machine designers building devices suitable for operation in extreme weather. It is essential for the designers and the users to define the principles and conditions for the safe operation of machines and devices with hydraulic drive in low ambient temperatures. Bearing in mind the above, the author tested the hydraulic motors in thermal shock...
-
Conditions for increasing the recognition of degradation in thermal-flow diagnostics, taking into account environmental legal aspects
PublikacjaThe ever-increasing demand for electricity and the need for conventional sources to cooperate with renewable ones generates the need to increase the efficiency and safety of the generation sources. Therefore, it is necessary to find a way to operate existing facilities more efficiently with full detection of emerging faults. These are the requirements of Polish, European and International law, which demands that energy facilities...
-
Ice Regime of the Kozłowa Góra Reservoir (Southern Poland) as an Indicator of Changes of the Thermal Conditions of Ambient Air
Publikacja -
Calculation of silicon cell temperature of loaded photovoltaic module based on thermal coefficients for different weather conditions of Northern Poland
PublikacjaWydajność obciążonego modułu fotowoltaicznego zależy silnie od natężenia promieniowania słonecznego, temperatury otoczenia, prędkości wiatru i temperatury wewnętrznej składowych ogniw fotowoltaicznych. Sprawność konwersji fotowoltaicznej spada istotnie wraz z e wzrostem temperatury złącza p-n. Pomiar tej temperatury jest niemożliwy i oblicza się ją w oparciu o mierzoną wartość temperatury przedniej lub tylnej powierzchni modułu...
-
Operating conditions-induced changes in product yield and characteristics during thermal-conversion of peanut shell to biochar in relation to economic analysis
Publikacja -
High-temperature oxidation of the Crofer 22 H ferritic steel with Mn1.45Co1.45Fe0.1O4 and Mn1.5Co1.5O4 spinel coatings under thermal cycling conditions and its properties
PublikacjaThe aim of the presented study was to deposit protective-conducting Mn1.45Co1.45Fe0.1O4 and Mn1.5Co1.5O4 spinel coatings on the Crofer 22 H ferritic steel by means of electrophoresis and to evaluate their physicochemical properties after high-temperature oxidation under thermal cycling conditions. When the Crofer 22 H steel – whether uncoated or coated with the two spinels – was oxidized in 48-h cycles involving a temperature of...
-
Physicochemical properties of Mn1.45Co1.45Cu0.1O4 spinel coating deposited on the Crofer 22 H ferritic steel and exposed to high-temperature oxidation under thermal cycling conditions
PublikacjaThe Crofer 22 H ferritic steel substrate was coated with an Mn1.45Co1.45Cu0.1O4 spinel by means of electrophoresis. After high-temperature oxidation under thermal cycling conditions, the physicochemical properties of the obtained system were evaluated. During 48-h cycles that involved heating the samples up to temperatures of either 750 or 800 °C, the oxidation kinetics of both coated and unmodified steel approximately obeyed...
-
Influence of synthesis conditions on glass formation, structure and thermal properties in the Na 2 O-CaO-P 2 O 5 system doped with Si 3 N 4 and Mg
PublikacjaOxynitride phosphate glasses and glass-ceramics were prepared using new synthesis routes for phosphate glasses. Materials were melted from pre-prepared glass samples in the system Na-Ca-P-O with addition of Mg and/or Si3N4 powders under different preparation conditions. The melting process was conducted at 1000–1500 °C either under air or nitrogen atmosphere to obtain materials with different nitrogen content. Their topography...
-
Dariusz Mikielewicz prof. dr hab. inż.
OsobyDariusz Mikielewicz – urodził się 6 lutego 1967 roku w Gdańsku, w 1985r. zdał pomyślnie egzaminy wstępne na Wydział Budowy Maszyn Politechniki Gdańskiej, który ukończył z wynikiem bardzo dobrym w 1990 roku na specjalności Maszyny i Urządzenia Energetyczne. Zainteresowania pracą naukową skłoniły go do podjęcia badań na University of Manchester na wydziale mechanicznym i energetyki jądrowej (Mechanical and Nuclear Engineering Department)...
-
Acceleration waves in the nonlinear micromorphic continuum
PublikacjaWithin the framework of the nonlinear elastic theory of micromorphic continua we derive the conditions for propagation of acceleration waves. An acceleration wave, also called a wave of weak discontinuity of order two, can be treated as a propagating nonmaterial surface across which the second derivatives of the placement vector and micro-distortion tensor may undergo jump discontinuities. Here we obtain the acoustic tensor for...
-
Consideration of the safety of bungee jumping in relation to mechanical properties of the instalation based on a jump accident in Gdynia
PublikacjaThis paper considers a bungee jumping accident that took place in July 2019 in Gdynia, Poland. The authors conducted an investigation to determine the cause of the bungee rope failure. It was based on mechanical tests concerning the strength of the rope as well as the calculation of the force induced in the rope during the jump. Based on the theoretical and experimental results, the rope safety factor was estimated. It appeared...
-
Singular curves in the resultant thermomechanics of shells
PublikacjaSome geometric and kinematic relations associated with the curve moving on the shell base surface are discussed. The extended surface transport relation and the extended surface divergence theorems are proposed for the piecewise smooth tensor fields acting on the regular and piecewise regular surfaces. The recently formulated resultant, two-dimensionally exact, thermodynamic shell relations - the balances of mass, linear and angular...
-
Junctions In Shell Structures: A Review
PublikacjaMany shell structures used in modern technology consist of regular shell parts joined together along their common boundaries. We review different theoretical, numerical, and experimental approaches to modelling, analyses and design of the compound shell structures with junctions. Several alternative forms of boundary, continuity and jump conditions at the singular midsurface curves modelling the shell junction are reviewed. We...
-
Adam Dąbrowski dr inż.
OsobyAdam Dąbrowski uzyskał stopień doktora nauk inżynieryjno-technicznych w dyscyplinie inżynieria mechaniczna na Politechnice Gdańskiej oraz ukończył studia II stopnia na kierunku mechatronika na Technische Universität Hamburg a także double degree Engineering and Management of Space Systems na Hochschule Bremen. Posiada doświadczenie przemysłowe (Instytut Lotnictwa w Warszawie, SICK AG w Hamburgu, Blue Dot Solutions w Gdańsku, Niemieckie...
-
INNOVATIVE THERMODYNAMICAL CYCLES BASED ON ENHANCEMENT MASS, MOMENTUM, ENTROPY AND ELECTRICITY TRANSPORT DUE TO SLIP, MOBILITY, TRANSPIRATION, ENTROPY AND ELECTRIC JUMPS AS WELL AS OTHER NANO-FLOWS PHENOMENA
PublikacjaIn our work, a further development of the authors model of thermo-chemical flow of fuel, air, oxygen, steam water, species, ionic and electron currents within nano channels and nano-structures of novel devices is presented. Different transport enhancement models are taken into account -among them the most important are: the velocity slip connected with complex external friction, the Darcy mobility and the Reynolds transpiration....
-
Fast Algorithms for Identification of Time-Varying Systems with Both Smooth and Discontinuous Parameter Changes
PublikacjaThe problem of noncausal identification of a time-varying linear system subject to both smooth and occasional jump-type changes is considered and solved using the preestimation technique combined with the basis function approach to modeling the variability of system parameters. The proposed estimation algorithms yield very good parameter tracking results and are computationally attractive.
-
Theory versus experiment for vacuum Rabi oscillations in lossy cavities
PublikacjaThe 1996 experiment by Brune et al. [Phys. Rev. Lett. 76, 1800 (1996)] on vacuum Rabi oscillation is analyzed by means of alternative models of atom-reservoir interaction. Agreement with experimental Rabi oscillation data can be obtained if one defines jump operators in the dressed-state basis and takes into account thermal fluctuations between dressed states belonging to the same manifold. Such low-frequency transitions could...
-
Numerical methods in heat and fluid flow, PG_00057408
Kursy OnlineReiteration of information on thermodynamic cycles and extension of information on their modelling using commercial software tools. Presentation of balances, constitutive equations, how to set up conditions in CFD type codes. Equipment regulation and control in the context of heat exchangers.Presentation of the computational capabilities of the CFD calculation code ANSYS Fluent. Mass, momentum and energy balances in 0D and 3D terms.Analysis...
-
Theoretical analysis of heat transfer between a liquid layer formed by an impinginf gas liquid jet AND a solid surface
PublikacjaHeat transfer phenomenon between a horizontal solid surface and a liquid layer created on a surface by an axisymmetrical liquid gas impinging jet has been analysed. The analytical treatment of the phenomenon is devoted to the area whose diameter is lower than the diameter of the hydraulic jump. W pracy przedstawiono teoretyczną analizę wymiany ciepła pomiędzy warstwą cieczy a stałą powierzchnią po której przepływa.
-
Ocena przekształceń piętrowego, ceglanego domu z dachem półpłaskim z przełomu XIX–XX wieku pod wpływem termomodernizacji na przykładzie gminy Puck, woj. pomorskie.
PublikacjaCeglane budynki mieszkalne z przełomu XIX i XX wieku, które stanowiły charakterystyczny element krajobrazu wsi pomorskiej, obecnie powszechnie poddawane są modernizacji w celu poprawy warunków cieplnych. Przedmiotem badania jest stan zachowania najmłodszego, historycznego typu domuw zagrodzie chłopskiej na Kaszubach – piętrowego, ceglanego domu z dachem półpłaskim. Badanie przeprowadzono na obszarze gminy Puck. Zidentyfikowano...
-
Kriging metamodels and design re‐utilization for fast parameter tuning of antenna structures
PublikacjaThe paper addresses the problem of computationally efficient electromagnetic (EM)‐driven design closure of antenna structures. The foundations of the presented approach are fast kriging interpolation metamodels, utilized for two purposes: (a) producing a good starting point for further parameter tuning, and (b) yielding a reasonable Jacobian matrix estimate to jump‐start the optimization procedure. The models are rendered using...
-
JOURNAL OF THERMAL ANALYSIS AND CALORIMETRY
Czasopisma -
A coupled constitutive model for fracture in plain concrete based on continuum theory with non-local softening and eXtended Finite Element Method
PublikacjaThe paper presents a constitutive model for concrete which combines a continuous and discontinuous fracture description. In a continuum regime, two different constitutive laws were used. First, a plasticity model with a Rankine failure criterion and an associated fl ow rule was used. Second, a constitutive law based on isotropic damage mechanics was formulated. In order to capture the width of a localized zone and to obtain mesh-independent...
-
Funkcjonowanie zespołów napędu hydraulicznego maszyn w niskich temperaturach otoczenia
PublikacjaW pracy przedstawiono cztery warianty klasyfikacji rozruchów oziębionego napędu hydraulicznego. Pierwsza sytuacja dotyczy zagadnienia, w którym wszystkie zespoły układu napędowego wraz z olejem mają taką samą niską temperaturę podczas rozruchu. Pozostałe warianty odnoszą się do rozruchu w warunkach szoku termicznego wywołanych zasilaniem ciepłym czynnikiem roboczym oziębionych zespołów hydraulicznych. Rozruch zespołów...
-
The electronic characterization of the cubic Laves-phase superconductor CaRh2
PublikacjaWe present the synthesis and experimental characterization of the electronic properties of the cubic Laves phase superconductor CaRh2. Its crystal structure was confirmed by powder X-ray diffraction and its ambient temperature lattice parameter (a = 7.5326(6) Å) is in good agreement with the literature. Magnetization, resistivity and heat-capacity measurements indicate that CaRh2 is a moderate-coupling type-II superconductor (λe-p = 0.89)...
-
APPLIED THERMAL ENGINEERING
Czasopisma -
Opracowanie ekspertyzy dotyczącej przyczyn pękania łopatek wirnika SP turbiny PG1 typu 13UP55
PublikacjaZakres badań i analiz dotyczył ustalenia przyczyn pękania elementów łopatek wirnika SPA5 turbiny TG1 typu 13UP55 obejmował: 1. wykonanie badań składu chemicznego stali, z której wykonano łopatki dostarczone przez Zleceniodawcę dwoma metodami, 2. badania mikroobszarów zniszczenia łopatek na mikroskopie elektronowym skaningowym z mikroanalizatorem EDS, 3. badania metalograficzne makroskopowe i mikroskopowe fragmentów...
-
Load testing of a suspended footbridge in Radom (Poland)
PublikacjaThe footbridge in Radom is a suspended bridge of an interesting architectural form. The structure was de-signed for 4 kN/m2 of crowd loading. Dynamic calculations were not included in the design. The structure’s acceptance tests took place on the 14th of October 2016. The behaviour of the footbridge in static testing met the expectations. Unfortunately, as a result of dynamic tests, dangerous behaviour of the footbridge was revealed....
-
Non-Destructive Testing of a Sport Tribune under Synchronized Crowd-Induced Excitation Using Vibration Analysis
PublikacjaThis paper presents the concept of repairing the stand of a motorbike speedway stadium. The synchronized dancing of fans cheering during a meeting brought the stand into excessive resonance. The main goal of this research was to propose a method for the structural tuning of stadium stands. Non-destructive testing by vibration methods was conducted on a selected stand segment, the structure of which recurred on the remaining stadium...
-
RuAl6—An Endohedral Aluminide Superconductor
PublikacjaSuperconductivity is reported in an endohedral aluminide compound, RuAl6, with Tc = 1.21 K. The normalized heat capacity jump at Tc, ΔC/γTc = 1.58, confirms bulk superconductivity. The Ginzburg–Landau parameter of κ = 9.5 shows that RuAl6 is a type-II superconductor. Electronic structure calculations for RuAl6 are explored in comparison to its structural analogue ReAl6 (Tc = 0.74 K). The stability of the phases is discussed in...
-
Superconductivity–Electron Count Relationship in Heusler Phases─the Case of LiPd2Si
PublikacjaWe report superconductivity in the full Heusler compound LiPd2Si (space group Fm3̅m, No. 225) at a critical temperature of Tc = 1.3 K and a normalized heat capacity jump at Tc, ΔC/γTc = 1.1. The low-temperature isothermal magnetization curves imply type-I superconductivity, as previously observed in LiPd2Ge. We show, based on density functional theory calculations and using the molecular orbital theory approach, that while LiPd2Si...
-
Superconductivity in the intermetallic compound Zr5Al4
PublikacjaPolycrystalline Zr5Al4 was synthesized using the arc-melting method. Powder X-ray diffraction confirms the previously reported crystal structure of the Ti5Ga4-type P63/mcm with lattice parameters: a = 8.4312(6) A , and c = 5.7752(8) A . Electrical resistivity and low-temperature magnetic susceptibility measurements indicate that Zr5Al4 exhibits superconducting behavior below 2 K. The normalized heat capacity jump at Tc= 1.82 K...
-
Superconductivity in CaBi2
PublikacjaSuperconductivity is observed with critical temperature Tc = 2.0 K in self-flux-grown single crystals of CaBi2. This material adopts the ZrSi2 structure type with lattice parameters a = 4.696(1) Å, b = 17.081(2) Å and c = 4.611(1) Å. The crystals of CaBi2 were studied by means of magnetic susceptibility, specific heat and electrical resistivity measurements. The heat capacity jump at Tc is DC/gTc = 1.41, confirming bulk superconductivity;...
-
Metoda f-chart w zastosowaniu do projektu instalacji solarnej w budownictwie jednorodzinnym
PublikacjaW artykule przedstawiono algorytm obliczeń cieplnych związanych z konwersją promieniowania cieplnego oraz analizę efektów pracy instalacji solarnej przy użyciu metody korelacyjnej f-chart. Zaprezentowany algorytm obliczeń cieplnych oraz omówiona w artykule podstawowa odmiana metody f-chart zostały poparte przykładem obliczeniowym dla instalacji solarnej, która wykorzystywana jest do wspomagania układu przygotowania c.w. dla potrzeb...
-
Mariusz Kaczmarek dr hab. inż.
OsobyReceived M.Sc., Eng. in Electronics in 1995 from Gdansk University of Technology, Ph.D. in Medical Electronics in 2003 and habilitation in Biocybernetics and Biomedical Engineering in 2017. He was an investigator in about 13 projects receiving a number of awards, including four best papers, practical innovations (7 medals and awards) and also the Andronicos G. Kantsios Award and Siemens Award. Main research activities: the issues...
-
Immittance Studies of Bi6Fe2Ti3O18 Ceramics
PublikacjaResults of studies focusing on the electric behavior of Bi6Fe2Ti3O18 (BFTO) ceramics are reported. BFTO ceramics were fabricated by solid state reaction methods. The simple oxides Bi2O3, TiO2, and Fe2O3 were used as starting materials. Immittance spectroscopy was chosen as a method to characterize electric and dielectric properties of polycrystalline ceramics. The experimental data were measured in the frequency range D = (101–107)...
-
Epilepsy and Paroxysmal Conditions
Czasopisma -
Influence of external walls' thermal capacitance on indoor thermal comfort
PublikacjaThe doctoral thesis presents the results of numerical investigations on the influence of walls’ thermal capacitance on indoor thermal comfort. A proper set of thermal parameters of a building structure can considerably limit the heating / cooling demand, and passively increase the indoor thermal comfort. However the effect of building thermal capacitance on indoor conditions is complex and not always beneficial. Among a great number...
-
15th Conference on Calorimetry and Thermal Analysis
WydarzeniaThe 15th Conference on Calorimetry and Thermal Analysis (CCTA 15) is the successive one in the cycle events coorganized by the Polish Society of Calorimetry and Thermal Analysis (PTKAT) this time Faculty of Chemistry of Gdańsk University of Technology and Stanislaw Staszic Research Association . The conference is devoted to application...
-
Hospital as a landscape mark
PublikacjaHalf of the nineteenth century brought significant changes in the organization and operation of hospitals. The on-coming takeover by the state and its agencies tasks related to medical care resulted in a significant jump in quantitative and almost massive construction of new hospitals. Several hospitals and nursing homes functioned on a relatively small area of a city or town, with different specializations and profiles of care....