Wyszukiwarka
Filtry
wszystkich: 4035
-
Katalog
- Publikacje 3588 wyników po odfiltrowaniu
- Czasopisma 206 wyników po odfiltrowaniu
- Konferencje 3 wyników po odfiltrowaniu
- Osoby 39 wyników po odfiltrowaniu
- Projekty 1 wyników po odfiltrowaniu
- Kursy Online 15 wyników po odfiltrowaniu
- Wydarzenia 1 wyników po odfiltrowaniu
- Dane Badawcze 182 wyników po odfiltrowaniu
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: experimental investigation of sprays
-
Experimental investigation of a two-phase thermosiphon.
PublikacjaPrzedstawiono wyniki badań dwufazowego, termosyfonowego wymiennika ciepła. W szczególności uwzględniono wpływ podziałki rur oraz wartość ciśnienia w płaszczu na gęstość przenoszonego strumienia ciepła.
-
Modeling and experimental investigation of the small UPQC systems
PublikacjaIn this paper the basis of analytical modelling of the UPQC arrangements (Unified Power Quality Conditioner) in d-q rotating coordinates, as well as select results of investigations conducted on the simplified small power laboratory model were talked over. In short form power balance as well as fundamental dependences and analytic model with regard of decoupling circuits were investigated. Applied method for DC link capacity selection...
-
Modeling and experimental investigation of the small UPQC systems
Publikacja -
Experimental and theoretical investigation into pressure field in a shroud clearance. Part I: Experimental research
PublikacjaPrzedstawiono wyniki badań eksperymentalnych rozkładu ciśnienia w uszczelnieniu nadbandażowym stopnia powietrznej turbiny modelowej. Badania przeprowadzono dla różnej częstości obrotowej wirnika i różnego obciążenia turbiny. Wyniki porównano z rezultatami obliczeń teoretycznych w II części artykułu.
-
Experimental investigation of joint with positive eccentricity in CFS truss
PublikacjaDue to technological restrictions, in the case of trusses made of CFS open cross-sections, positive eccentricities in the truss joints have become very frequent. Therefore studies concerning the load-bearing capacity of truss joints with positive eccentricity were undertaken. It was assumed that the resistance of cold-formed steel (CFS) open cross-section truss joints located on compression chords and with positive eccentricity...
-
An experimental investigation of the influence of plasticity on creep degradation rate
Publikacja -
Theoretical and experimental investigation of Optical Coherent Tomography topologies
PublikacjaW artykule przedstawiono teoretyczną i eksperymentalną analizę konfiguracji interferometrów w układach koherentnego tomografu optycznego. Zaprezentowano zrealizowany układ, którego specjalnie zaprojektowana konfiguracja pozawala na analizę zmian polaryzacji sygnału pomiarowego.
-
An experimental investigation of the influence of plasticity on creep degradation rate
Publikacja -
Experimental and theoretical investigation of microjet cooling in metalurgical applications
PublikacjaW pracy zaprezentowano model wrzącej strugi uderzającej o powierzchnię i wytwarzającej cienki film cieczowy, w którym tworzą się pęcherzyki pary.
-
Detection of additional mass in rods: Experimental and numerical investigation
PublikacjaW pracy przedstawiono wyniki badań eksperymentalnych i numerycznych nad wykorzystaniem zmian w propagacji fal sprężystych do detekcji masy skupionej znajdujacej się w konstrukcji prętowej.
-
Experimental investigation of Organic Rankine Cycles for domestic micro CHP
PublikacjaW artykule przedstawiono wyniki badań eksperymentalnych obiegu ORC wyposażonego w ekspander typu scroll (I etap badań) oraz ekspander utworzony na bazie turbinki pneumatycznej (II etap badań). Raportowane badania przeprowadzono na laboratoryjnym stanowisku realizującym obieg ''domowej'' mikrosiłowni parowej.
-
Selected problems of experimental investigation of dynamically loaded journal bearings
PublikacjaIn the paper some problems concerning relations between external bearing loadings and critical lining stresses are described for test stand with rotating load vector. According to the standard ISO 7905/1 this type of test stand, for dynamically loaded slide bearing, is recommended as a basic research unit for material testing in a complete bearing unit. The lining stress calculation results occurred being dependent on applied calculation...
-
Experimental investigation into surface texture effect on journal bearings performance
PublikacjaThe aim of this study was to analyse the performance of journal bearings with specially created dimples on the sliding surface and operating under various conditions. The texture was created on the bearing surface that co-acted with the smooth journal; moreover, the variation of the textured surface of the journal mating with the smooth bearing was tested, and the results were compared to those obtained with the standard smooth...
-
Experimental investigation of domestic gas boiler fitted with ORC module
PublikacjaIn the paper the prototype of innovative domestic cogenerative ORC system, consisting of a conventional gas boiler and a small size axial vapour microturbines (in-house designed for ORC and the commercially available for Rankine cycle (RC)), evaporator and condenser were scrutinised. In the course of study the fluid working temperatures, rates of heat, electricity generation and efficiency of the whole system were obtained. The...
-
Experimental Investigation of Prototype Water-Lubricated Compliant Foil Bearings
PublikacjaPraca zawiera wyniki badań doświadczalnych prototypowego łożyska foliowego smarowanego wodą. Łożyska tego typu mogą mieć zastosowanie w węzłach, od których wymaga się ekologicznego środka smarowego, np. pompy wodne czy turbiny wodne. W opracowaniu zademonstrowano wyniki badań trzech prototypowych poprzecznych łożysk foliowych. Opisano napotkane problemy badań oraz wprowadzonych do konstrukcji łożyska zmian, których celem była poprawa...
-
Nucleate pool boiling modelling and experimental investigation : chapter 7
PublikacjaOmówiono wpływ powłoki porowatej nanoszonej na całą powierzchnię rurki lub jej fragment na osiągany współczynnik przejmowania ciepła, krytyczne gęstości strumienia ciepła, a także obwodowy rozkład temperatury przy wrzeniu pęcherzykowym na zewnętrznej powierzchni poziomej rurki.Przedstawiono wyniki badań częstotliwości odrywania się pęcherzyków oraz pól prędkości wokół wzrastającyh i unoszących się pęcherzyków przy wrzeniu z pojedynczych...
-
An Experimental Investigation of Pressure Wave Celerity During the Transient Slurry Flow
PublikacjaTransportation of slurries in pressure pipelines is an example of a complex flow due to specific parameters of transported medium. For practitioners, the economy of designing and maintenance is usually the most important factor. For this reason, most of hydrotransport installations are fairly simple; however, they become more vulnerable to negative effects of the transient flow which can occur in pressure pipelines. As the consequence,...
-
Comparative study of numerical modelling and experimental investigation for vessel-docking operations
PublikacjaA comparative study between numerical modelling and experimental investigation is performed to validate the developed numerical method for simulating floating dock operations with a vessel on board. Both model-scale and full-scale experimental tests are performed on floating docks with a vessel on board, and the draughts using draught meters, floating positions and bending of the floating dock are measured. The present numerical...
-
Response of a steel tank during earthquakes and mining tremors - experimental investigation
PublikacjaCylindrical steel tanks are very popular shell structures used to store the products of chemical and petroleum industries. Any failure might have disastrous consequences, therefore their safety and reliability is essential. Earthquakes are the most dangerous and also the most unpredictable dynamic loads acting on such structures. On the other hand, mining tremors are usually considered to be less severe due to lower acceleration...
-
Experimental investigation of two-phase thermosyphon heat exchanger charged with acetone
PublikacjaThis paper presents thermal characteristics of prototype of a two-phase thermosyphon heat exchanger (TPTHEx) charged with acetone as a working fluid. The TPTHEx consists of two horizontal cylindrical vessels connected by two risers and a downcomer. Tube bundles placed in the lower and upper cylinders work as an evaporator and a condenser, respectively. The tested TPTHEx operates in a vacuum. Therefore, the working liquid is boiled...
-
Experimental an numerical investigation of wave propagation in composite beam with an additional mass
PublikacjaW pracy przedstawiono wyniki badań eksperymentalnych i symulacji numerycznych ilustrujace wpływ dodatkowej masy na propagacje fali Lamba w belce kompozytowej.
-
Experimental investigation of the PEM fuel cells performance for automotive and stationary applications
PublikacjaThe aim of the study was to provide dynamic characteristics of the PEM fuel cell system consisted of Nexa modules, provide steady-state characteristics of the for different values of air excess ratio and steady-state characteristics for different stack temperatures and given load.
-
Experimental Investigation of Elastic Waves Propagation in 1D and 2D Structures with Faults.
PublikacjaW pracy omówiono wyniki pomiarów fal sprężystych w prętach, belkach i płytach z uszkodzeniami.
-
Numerical and experimental investigation of thermal convection near electric devices with vertical channels
PublikacjaThis paper presents the results of numerical and experimental investigation of thermal convection near heat emitting surfaces of an electric device. For the intensification of thermal convection, special vertical channels were formed near the heat emitting surfaces of the device. An experimental test has proved that there is an optimal length of the channels – thermal convection is the most intensive then. Air velocity vectors...
-
Numerical and experimental investigation of rotational stiffness of zed-purlins connection with sandwich panels
PublikacjaA rotational resistant stiffness of the zed-purlins connection with sandwich panels is investigated. A simple finite element method model of the connection is proposed. The numerical analysis of the model performed by ABAQUS software, in physically linear and geometrically nonlinear ranges, leads to the rotational resistant stiffness sought. The numerical solution obtained is verified experimentally. Two variants of distribution...
-
EXPERIMENTAL INVESTIGATION OF FREE CONVECTION OF GLYCOL-Al2O3 NANOFLUID FROM HORIZONTAL TUBE
PublikacjaNanofluids came to be seen as a new generation of coolants, both in single- and two phase systems. Furthermore, nanofluids or nanocomposites may be used as a media in a thermal energy storage (TES) in such systems as sensible heat storage (SHS) and phase change materials (PCM). In the SHS systems the dominating mechanism of the heat transfer is natural convection. However, in the literature only a few investigations of free convection...
-
Experimental investigation of free convection of glycol-Al2O3 nanofluid from horizontal tube
PublikacjaNanofluids came to be seen as a new generation of coolants, both in single- and two phase systems. Furthermore, nanofluids or nanocomposites may be used as a media in a thermal energy storage (TES) in such systems as sensible heat storage (SHS) and phase change materials (PCM). In the SHS systems the dominating mechanism of the heat transfer is natural convection. However, in the literature only a few investigations of free convection...
-
Experimental Investigation of Free Convection Heat Transfer from Horizontal Cylinder to Nanofluids
PublikacjaThe results of free convection heat transfer investigation from a horizontal, uniformly heated tube immersed in a nanofluid are presented. Experiments were performed with five base fluids, i.e., ethylene glycol (EG), distilled water (W) and the mixtures of EG and water with the ratios of 60/40, 50/50, 40/60 by volume, so the Rayleigh (Ra) number range was 3 104 Ra 1.3 106 and the Prandtl (Pr) number varied from 4.4 to 176....
-
Experimental and Numerical Investigation of Tensile and Flexural Behavior of Nanoclay Wood-Plastic Composite
PublikacjaIn this study, the effect of wood powder and nanoclay particle content on composites’ mechanical behavior made with polyethylene matrix has been investigated. The wood flour as a reinforcer made of wood powder was at levels of 30, 40, and 50 wt.%, and additional reinforcement with nanoclay at 0, 1, 3, and 5 wt.%. Furthermore, to make a composite matrix, high-density polyethylene was used at levels of 70, 60, and 50% by weight....
-
Experimental and Numerical Investigation of Mechanical Properties of Lightweight Concretes (LWCs) with Various Aggregates
PublikacjaHigh requirements for the properties of construction materials and activities directed at environment protection are reasons to look for new solutions in concrete technology. This research was directed at solutions affecting the reduction of energy consumption and CO2 emissions. The use of lightweight concretes (LWCs) allows one to meet both conditions at the same time. The purpose of the research presented in this paper was to...
-
Experimental Investigation of high frequency 3L-NPC qZS inverter for photovoltaic application
Publikacja -
Experimental Investigation of an Intensified Heat Transfer Adsorption Bed (IHTAB) Reactor Prototype
Publikacja -
Experimental investigation of utilizing waste flue gas desulfurized gypsum as backfill materials
Publikacja -
Experimental Investigation of the Properties of Laminated Nonwovens Used for Packaging of Powders in Mineral Warmers
Publikacja -
Experimental investigation of forced convection of water-Al2O3 nanofluids inside horizontal tubes,
PublikacjaIn this paper, forced convection of water–Al2O3 nanofluids inside horizontal copper tube is studied experimentally. Experiments were conducted for three, i.e. 0.1%, 1% and 5% nanoparticle mass concentrations under transition and turbulent flow regimes. Average heat transfer coefficients and pressure drop values were determined and compared to distilled water. Enhancement of heat transfer for lower nanoparticle concentration and...
-
Experimental investigation of forced convection of water/EGAl2O3 nanofluids inside horizontal tube
PublikacjaIn this paper, forced convection of water/EG-Al2O3 nanofluids inside horizontal stainless steel tube is studied experimentally. As base fluid served water/EG mixture of two ratios (60:50 and 50:50). Nanoparticle mass concentrations was 0.1% or and 1%. Transition and turbulent flow regimes were tested. Average heat transfer coefficient and pressure drop values were determined for nanofluids and compared to base fluids. Deterioration...
-
Experimental and theoretical investigation of pressure field in a shroudclearance. Part II: Theoretical results
PublikacjaPrzedstawiono wyniki obliczeń teoretycznych metodami CFD rozkładu ciśnienia w uszczelnieniu nadbandażowym stopnia powietrznej turbiny modelowej. Badania przeprowadzono stosując metody: Miltiple Reference Frame, Mixing Plane iSliding Mesch. Wyniki porównano z rezultatami badań eksperymentalnych.
-
Experimental Investigation of the ORC System Elements of a Home Cogenerative Micro Power Plant
PublikacjaW pracy przedstawiono wyniki badań obiegu ORC z prototypową pompą czerpakową czynnika roboczego HFE 7100 i elektrycznym przepływowym podgrzewaczem oleju termalnego w układzie ORC bez regeneracji. Z analizy wyników badań wynika, że w obiegu ORC bez regeneracji z zaworem rozprężnym (symulującym pracę mikroturbiny) osiągnięto przegrzanie par czynnika niskowrzącego HFE 7100. Uzyskano powtarzalność wyników badań wykonanych serii pomiarowych...
-
Experimental investigation of the weight averaging of pulse frequency modulated sensor output signal
Dane BadawczeThe research aims to practically verify the results of theoretical analysis and simulations of the efficiency of weight averaging of pulse frequency modulated signal. For this purpose, a suitable test stand was built, and the control software in the LabVIEW environment was prepared. Then, a series of experiments were carried out to process and analyze...
-
Experimental investigation and process parameter optimization of sheet metal bending by line heating method
PublikacjaThe present study is concerned with the experimental investigation of sheet metal deforming by line heating method that incorporates the combined effect of traverse speed of the torch, thickness of the sheet metal, and the number of passes of the torch. For the numerical analysis of metal bending by line heating, the
-
Experimental and numerical investigation of mercury removal from flue gas by sorbent polymer composite
PublikacjaThis paper presents an experimental and numerical investigation of the performance of a sorbent polymer composite (SPC) material used for removing mercury from the flue gases in a full-scale industrial installation. The investigated material is an attractive alternative to activated carbon, which is commonly used for this purpose. While the application of the SPC is characterized by high capital expenditures, this technology offers...
-
Experimental investigation of dryout of SES36, R134a, R123 and ethanol in vertical small diameter tubes
PublikacjaW publikacji przedstawiono wyniki badań eksperymentalnych kryzysu wrzenia typu dryout podczas wrzenia w przepływie czterech czynników (SES36, R134a, R123, alkohol etylowy) w kanałach o średnicy wewnętrznej 1.15 mm i 2.3 mm. Badania przeprowadzono w szerokim zakresie zmian stopnia suchości pary (0.65-1), gęstości strumienia masy (40-900 kg/(m2s)) i gęstości strumienia ciepła (20-220 kW/m2). W badaniach wykorzystano technikę termowizyjną...
-
Experimental investigation on heat pipes supported by soy wax and lauric acid for electronics cooling
PublikacjaThis paper presents an experimental study of heat pipes for electronics cooling that were supported by energy storage materials (i.e. phase change materials - PCMs) coated at the adiabatic section. The PCMs utilized included two materials, namely lauric acid and soy wax, the latter being considered as a more cost-effective alternative. The study focused on three different powers: 20 W, 25 W, and 30 W. Both heating, cooling, and...
-
Investigation on water infiltration and water content changes in a large-scale experimental test dike
PublikacjaThe paper presents result of series of experiments made within the DREDGDIKES project, performed on a test dike built from composite soil. The composite is produced by mixing fly ash (by-product of energetics) with dredged material (sand) taken from the mouth of The Vistula river. The test dike, located near Gdansk in Poland, was subjected to hydraulic load in several flooding time scenarios and the unsaturated unsteady flow was...
-
Experimental Investigation of the Performance of an Innovative Implantable Left Ventricular Assist Device—Proof of Concept
PublikacjaThis paper presents the results of experimental performance of an innovative left ventricular assist device working on a specially designed test stand. The introduced invention is mainly applied for supporting the heart in patients with end-stage heart failure accompanied by mitral valve regurgitation and pulmonary hypertension. Moreover, the developed device has the form of a flexible balloon forming an intracardiac inert gas-filled...
-
Experimental and theoretical investigation of conformational states and noncovalent interactions in crystalline sulfonamides with a methoxyphenyl moiety
PublikacjaFour sulfonamide derivatives with a methoxyphenyl moiety, namely N-{4-[(2-methoxyphenyl)sulfamoyl] phenyl}acetamide (1a), N-{4-[(3-methoxyphenyl)sulfamoyl]phenyl}acetamide (1b), 4-amino-N-(2- methoxyphenyl)benzenesulfonamide (2a) and 4-amino-N-(3-methoxyphenyl)benzenesulfonamide (2b), have been synthesized and characterized physiochemically by CHNS, MS, FT-IR, 1H NMR, 13C NMR, PXRD and TG methods. Crystal structures were determined...
-
Experimental investigation of domestic micro-CHP based on the gas boiler fitted with ORC module
PublikacjaThe results of investigations conducted on the prototype of vapour driven micro-CHP unit integrated with a gas boiler are presented. The system enables cogeneration of heat and electric energy to cover the energy demand of household. The idea of such system is to produce electricity for own demand or for selling it to the electric grid – in such situation the system user will became the prosumer. A typical commercial gas boiler,...
-
Experimental investigation of the flow pattern and wall pressure distribution in a silo with double-cone insert
PublikacjaArtykuł opisuje przeprowadzone badania przepływów silosowych i naporu materiałów sypkich podczas napełniania i opróżniania silosu o średnicy 2.5 m wyposażonego we wkładkę "podwójny stożek". Badania przeprowadzane były w Instytucie Badawczym Tel-Tek w Norwegii. Materiałem użytym był suchy piasek. Napór na ścianę mierzony był bezpośrednio za pomocą 10 czujników wbudowanych w ścianę. Badania eksperymentalne pokazały duży wpływ wkładki...
-
Experimental investigation of Steel–Concrete–Polymer composite barrier for the ship internal tank construction
PublikacjaTransportation of dangerous cargo by ships demands ensuring an appropriate protection level in case of an accident. Two of the most dangerous accident types resulting in an oil spill are grounding and ship to ship collision. The article presents results of research on a new composite construction for a ship hull that increases structural safety during collision. The concept of semi-elastic Steel–Concrete–Polymer structure is presented....
-
Dataset Related Experimental Investigation of Chess Position Evaluation Using a Deep Neural Network
PublikacjaThe idea of training Articial Neural Networks to evaluate chess positions has been widely explored in the last ten years. In this paper we investigated dataset impact on chess position evaluation. We created two datasets with over 1.6 million unique chess positions each. In one of those we also included randomly generated positions resulting from consideration of potentially unpredictable chess moves. Each position was evaluated...