Filtry
wszystkich: 1465
wybranych: 671
-
Katalog
- Publikacje 671 wyników po odfiltrowaniu
- Czasopisma 7 wyników po odfiltrowaniu
- Wydawnictwa 2 wyników po odfiltrowaniu
- Osoby 34 wyników po odfiltrowaniu
- Wynalazki 1 wyników po odfiltrowaniu
- Projekty 21 wyników po odfiltrowaniu
- Zespoły Badawcze 1 wyników po odfiltrowaniu
- Aparatura Badawcza 9 wyników po odfiltrowaniu
- Kursy Online 35 wyników po odfiltrowaniu
- Wydarzenia 4 wyników po odfiltrowaniu
- Dane Badawcze 680 wyników po odfiltrowaniu
Filtry wybranego katalogu
Wyniki wyszukiwania dla: UAC
-
Ocena przydatności klasycznych metod pomiaru impedancji pętli zwarciowej do obwodów z wyłącznikami różnicowoprądowymi
PublikacjaW referacie przedstawiono wyniki badań zachowania się wyłączników różnicowoprądowych przy pomiarze impedancji pętli zwarciowej, wykonanym wybranymi miernikami. Badania przeprowadzono w obwodach z wyłącznikami różnicowoprądowymi o znamionowym prądzie różnicowym równym 30 mA, typu AC oraz typu A. Na podstawie przeprowadzonych badań i analiz zaproponowano sposób pomiaru impedancji pętli zwarciowej, który nie powoduje zbędnego zadziałania...
-
Modular multipulse voltage source inverters with integrating coupled reactors
PublikacjaA novel approach to the voltage source inverters (VSI) construction is presented in the paper. The invented inverter structures allow to operate several DC/AC converters in parallel resulting in lower voltage distortions at extremely low switching frequency. The research presented in the paper describes such a parallel operation of the VSI’s which is possible thanks to the use of coupled inductors. The eighteen-pulse and twenty-four-pulse...
-
System regulacji promeniowania UV w instalacjach uzdatniania wody.
PublikacjaPrzedstawiono zastosowanie opracowanego przez autorów źródła prądowego AC do regulacji promieniowania wydzielanego przez niskociśnieniowe lampy wyładowcze. Źródło prądowe sterowane mikrosterownikiem pozwala na zasilanie różnego typu lamp UV stosowanych w instalacjach uzdatniania wody. Wyposażenia instalacji w czujniki UV oraz czujniki przepływu wody daje możliwość regulacji dawki promieniowania UV na stałym poziomie bez względu...
-
Koncepcja modelu do badnia wydajności domeny IP QoS
PublikacjaCelem artykułu jest przedstawienie koncepcji hierarchicznie rozproszonego brokera MBB (Multiple Bandwidth Broker) realizującego funkcje AC w oparciu o pomiary. Zaproponowane zostały przez autorów modele funkcjonalne brokera centralnego oraz brokera brzegowego. Autorzy zaproponowali także algorytm realizujący MBAC, zaimplementowany w brokerze brzegowym. Prezentowany model koncepcyjny umożliwia zwiększenie skalowalności DS oraz ograniczenie...
-
Wpływ struktury siluminu na skrawalność = Effect of silumin structure on machinability
PublikacjaBadano odlewy ciśnieniowe ze siluminu EN AC-AlSi7Cu2 pochodzące z dwóch partii różniące się skrawalnością, w zakresie składu chemicznego, mikrostruktury na mikroskopie świetlnym i skaningowym z EDS oraz składu fazowego na dyfraktometrze rentgenowskim. Stop o niższej skrawalności posiadał mniejszą dyspersję eutektyki, większe stężenie tytanu w roztworze aluminium, wydzielenia fazy międzymetalicznej Al i Ti oraz większe skupiska...
-
Modern Arrangement for Reduction of Voltage Perturbations
PublikacjaThe contents of this chapter encompass general problems and the most important issues of power-supply-quality improvement in AC systems. In the context of the above, consideration is given to evaluation of bilateral interactions of receivers with an electrical power-distribution system and methods of their reduction. Also are discussed the basis of operation of the most important compensation-filtration devices and their applications...
-
Investigation of magnetic order in a new intermetallic compound Nd2PtGe3
PublikacjaIn the present study we report a successful synthesis of the new intermetallic compound Nd2PtGe3 by an arc-melting method. The powder X-ray diffraction analysis indicates that this compound crystallizes in an disordered variant of the AlB2-type structure (space group P6/mmm, no. 191) with lattice parameters a = 4.2455 Å and c = 4. 1933 Å. The compound exhibits a cluster-glass transition below Tf = 2.9 K, characterized through ac...
-
Application of Traction Supply System for Charging Electric Cars
PublikacjaThe development of electromobility involves the development of electric cars charging infrastructure. The increase of the number of chargers poses new demands for the AC power grid, especially in regard to its capacity of delivering high peak power. As an alternative for the public AC power grid, urban electrified transportation systems (trams, trolleybuses, and metro) can be used for supplying electric cars chargers. The article...
-
Obserwatory prędkości dla bezczujnikowego sterowania maszynami prądu przemiennego
PublikacjaPrzedstawiono model matematyczny uogólnionej maszyny elektrycznej rozszerzony przez wprowadzenie dodatkowych zmiennych. Na podstawie modelu rozszerzonego opracowano strukturę obserwatora prędkości maszyny uogólnionej. Zaprezentowano struktury obserwatorów prędkości dla poszczególnych rodzajów maszyn prądu przemiennego. Pokazano, że prędkość kątową wirnika można odtwarzać dla różnych typów maszyn stosując odpowiednie zmienne stanu...
-
Discouraging Traffic Remapping Attacks in Local Ad Hoc Networks
PublikacjaQuality of Service (QoS) is usually provided in ad hoc networks using a class-based approach which, without dedicated security measures in place, paves the way to various abuses by selfish stations. Such actions include traffic remapping attacks (TRAs), which consist in claiming a higher traffic priority, i.e., false designation of the intrinsic traffic class so that it can be mapped onto a higher-priority class. In practice, TRAs...
-
Stone cutting industry waste-supported zinc oxide nanostructures for ultrasonic assisted decomposition of an anti-inflammatory non-steroidal pharmaceutical compound
PublikacjaPowdered stone waste (PSW) obtained from a stone cutting industrial unit was applied as support for the immobilization of nano-sized ZnO to be utilized as an effective catalyst for the catalytic conversion of acetaminophen (ACE) under ultrasonication. The incorporation of ZnO nanostructures into PSW structure enhanced the specific surface area and pore volume of the as-prepared nanocompound. The change in the value of zero point...
-
Assessment of the Steering Precision of a Hydrographic Unmanned Surface Vessel (USV) along Sounding Profiles Using a Low-Cost Multi-Global Navigation Satellite System (GNSS) Receiver Supported Autopilot
Publikacjahe performance of bathymetric measurements by traditional methods (using manned vessels) in ultra-shallow waters, i.e., lakes, rivers, and sea beaches with a depth of less than 1 m, is often difficult or, in many cases, impossible due to problems related to safe vessel maneuvering. For this reason, the use of shallow draft hydrographic Unmanned Surface Vessels (USV) appears to provide a promising alternative method for performing...
-
Sensorless predictive control of three-phase parallel active filter
PublikacjaThe paper presents the control system of parallel active power filter (APF) with predictive reference current calculation and model based predictive current control. The novel estimator and predictor of grid emf is proposed for AC voltage sensorless operation of APF, regardless of distortion of this voltage. Proposed control system provides control of APF current with high precision and dynamics limited only by filter circuit parameters....
-
ANALIZA SCZEPNOŚCI MIĘDZYWARSTWOWEJ DWUWARSTWOWO WBUDOWANEJ PODBUDOWY ASFALTOWEJ NA ODCINKU KM 335+946 – 356+850 STR. P ORAZ JEJ WPŁYW NA TRWAŁOŚĆ KONSTRUKCJI NAWIERZCHNI „Budowa mostu przez rzekę Nogat w Malborku wraz z dojazdami w ciągu dróg krajowych nr 22 i 55"
PublikacjaCelem pracy jest ocena jakości połączenia dwóch warstw technologicznych podbudowy z betonu asfaltowego AC 22 35/50 o całkowitej grubości 18 cm oraz wpływ tego połączenia na trwałość konstrukcji nawierzchni drogi na odcinku km 355+946 – 356+850 str. P, wbudowanej w ramach realizacji kontraktu „Budowa mostu przez rzekę Nogat w Malborku wraz z dojazdami w ciągu dróg krajowych nr 22 i 55”.
-
ROBOT TYPU QUADROCOPTER STEROWANY MIKROKONTROLERAMI O NIEWIELKIEJ MOCY OBLICZENIOWEJ
PublikacjaWspółczesna robotyka rozwija się bardzo dynamicznie. Coraz więcej osób prywatnych i inżynierów konstruuje różnego rodzaju pojazdy mobilne. Dlatego autorzy niniejszego referatu postawili sobie następującą tezę: możliwa jest budowa latającego robota mobilnego na bazie kontrolera o niskiej mocy obliczeniowej oraz prostego regulatora, i podjęli się jej udowodnienia.
-
Electrical properties and structure of lead-borate glass containing iron ions.
PublikacjaThe ac and dc conductivity in iron–lead-borate glass samples was investigated in the frequency range from 1 mHz to 1 MHz and in the temperature range from 153 K to 423 K. The structure was investigated by the means of atomic force microscopy (AFM) and the crystalline phases (if present) were identified by the means of X-ray diffractometry. Two types of ac electrical behaviour were observed. The first group of glass samples which...
-
Assessment of Electronic Sensing Techniques for the Rapid Identification of Alveolar Echinococcosis through Exhaled Breath Analysis
PublikacjaHere we present a proof-of-concept study showing the potential of a chemical gas sensors system to identify the patients with alveolar echinococcosis disease through exhaled breath analysis. The sensors system employed comprised an array of three commercial gas sensors and a custom gas sensor based on WO3 nanowires doped with gold nanoparticles, optimized for the measurement of common breath volatile organic compounds. The measurement...
-
Field investigation of low-temperature cracking and stiffness moduli on selected roads with conventional and high modulus asphalt concrete
PublikacjaHigh Modulus Asphalt Concrete (HMAC) was introduced in Poland as a one of the solutions to the problem of rutting, type of deterioration common in the 1990s. After first encouraging trials in 2002 HMAC was widely used for heavily loaded national roads and motorways. However some concerns were raised about low-temperature cracking of HMAC. This was the main reason of the studies presented in this article were started. The article...
-
Feedback Control of Doubly-Fed Generator Connected to Current Source Converter
PublikacjaDoubly-fed induction generator (DFIG) system supplied by current source converter (CSC) is considered in this article. The DFIG can work in two independent modes: AC grid connection and stand-alone mode. The DFIG is connected to the ac grid directly through its stator and the CSC links the rotor side. In this mode, the active and reactive powers of the DFIG must be controlled. This article proposes two control system structures...
-
MODEL HYBRYDOWEGO ENERGOELEKTRONICZNEGO UKŁADU ZASILANIA WIELOSYSTEMOWYCH ZESPOŁÓW TRAKCYJNYCH (EZT)
PublikacjaW artykule przedstawiono model układu hybrydowego energoelektronicznego układu zasilania wielosystemowych zespołów trakcyjnych - EZT. Istota proponowanego rozwiązania zawiera się w zastosowaniu do obniżenia napięcia sieci trakcyjnej, zamiast tradycyjnego ciężkiego transformatora trakcyjnego (chłodzonego olejem) - suchego autotransformatora pracującego z częstotliwością sieci kolejowej oraz izolacji galwanicznej od sieci trakcyjnej....
-
Zastosowanie termowizji w diagnostyce i badaniach sprzętu elektronicznego
PublikacjaZaproponowano zastosowanie techniki termowizyjnej do oceny poprawność konstrukcji i działania urządzeń elektronicznych, biorąc pod uwagę krótki czas badań oraz możliwość bezpośredniej oceny uzyskanych wyników. Technikę termowizyjną zastosowano do badania elementów ochronnych zasilacza AC/DC w czasie standardowych badań odporności na udary oraz do badania modułów GSM pracujących pod kontrolą nadrzędnego programu sterującego i płyty...
-
Zastosowanie termografii w diagnostyce i badaniach urządzeń elektronicznych
PublikacjaZaproponowano zastosowanie techniki termowizyjnej do oceny poprawność konstrukcji i działania urządzeń elektronicznych, biorąc pod uwagę krótki czas badań oraz możliwość bezpośredniej oceny uzyskanych wyników. Technikę termowizyjną zastosowano do badania elementów ochronnych zasilacza AC/DC w czasie standardowych badań odporności na udary oraz do badania modułów GSM pracujących pod kontrolą nadrzędnego programu sterującego i płyty...
-
Impedance Studies of Phosphate-iron Glasses Containing Niobium and Titanium
PublikacjaThe ac and dc conductivity in phosphate-iron-niobate glasses with addition of titanium oxide was investigated as a function of temperature and frequency with the use of impedance spectroscopy. The topography and microstructure of glasses were investigated by the means of X-ray diffraction (XRD), scanning electron microscopy (SEM), and confocal microscopy methods. The obtained results show that all samples are amorphous but they...
-
A Review of Reduction Methods of Impact of Common-Mode Voltage on Electric Drives.
PublikacjaIn this survey paper, typical solutions that focus on the reduction in negative effects resulting from the common-mode voltage influence in AC motor drive applications are re-examined. The critical effectiveness evaluation of the considered methods is based on experimental results of tests performed in a laboratory setup with an induction machine fed by an inverter. The capacity of a common-mode voltage level reduction and voltage...
-
Experimental test results of the 150kVA 18-pulse diode rectifier with series active power filter
PublikacjaThe paper presents the control system and selected results of experimental tests of the ac/dc power converter consisting of 18-pulse diode rectifier on the basis of coupled reactors and a serial active power filter. Three configurations of the 150kVA converter were tested experimentally and compared: 18-pulse diode rectifier with and without additional grid reactor and the rectifier integrated with the active power filter. The...
-
Assessment of copper surface coverage with corrosion inhibitor using AFM-based local electrical measurements
PublikacjaThe paper presents a new method of assessment of metal surface coverage with corrosion inhibitor and thus of inhibitor protective performance. It is based on the atomic force microscopy measurement performed in a contact mode. Apart from topography images the proposed approach allows acquisition of local DC maps and local electrical impedance spectra via application of DC bias voltage or AC perturbation signal between the conductive...
-
Design of high frequency OTA in 130nm CMOS technology with single 1.2v power supply
PublikacjaW artykule przedstawiono wzmacniacz transkonduktancyjny OTA zasilany niskim napięciem i przeznaczony do użycia w filtrach czasu ciągłego w zakresie wysokich częstotliwości przetwarzanych sygnałów. Stopień wejściowy zbudowany jest w oparciu o inwertery CMOS. Wartość transkonduktancji wzmacniacza jest przestrajana z wykorzystaniem efektu podłożowego tranzystorów. Omówiono również układ dostrajania wzmacniacza. Brak wewnętrznych węzłów...
-
Reaktywny system oddziaływania ze środowiskiem oparty na inteligentnym systemie decyzyjnym
PublikacjaProcesy poznawcze zachodzące w umyśle człowieka, po matematycznym zamodelowaniu i algorytmizacji, mogą by wykorzystane do konstruowania inteligentnych systemów decyzyjnych. Systemy takie mają wielorakie zastosowania. Znaleźć można je między innymi w rozmaitych autonomicznych systemach informatyki, automatyki i robotyki: począwszy od 'inteligentnego' strażnika, kamerdynera, itp., a skończywszy na opiekunie - wirtualnym towarzyszu...
-
IoT for healthcare applications
PublikacjaThis chapter summarizes IRACON contributions related to the application of IoT in healthcare. It consists of the following three sections. Section 8.1 presents the measurement campaigns and the related statistical analysis to obtain various channel models for wearable and implantable devices. In addition, the importance of physical human-body phantoms used for channel, Specific Absorption Rate (SAR), and Electromagnetic (EM) exposure...
-
Green analytical chemistry metrics: A review
PublikacjaGreen analytical chemistry encourages reducing the use of toxic chemicals/reagents, using energy-efficient equipment, and generating minimal waste. The recent trends in analytical method development focus on the miniaturization of the sample preparation devices, the development of solventless or solvent-minimized extraction techniques, and the utilization of less toxic solvents. The twelve principles of GAC serve as a basic guideline...
-
Low cost set-up for supercapacitors parameters evaluation
PublikacjaSupercapacitors are capable to store relatively high amount of energy comparing to its mass. Growing number of these devices applications requires development of new testing methods. Standard methods of evaluation of supercapacitor parameters, as cycling voltammetry, CV, galvanostatic cycling with potential limitation, GCPL, impedance measurements, require equipment of high cost...
-
Analytical procedures for short chain chlorinated paraffins determination - How to make them greener?
PublikacjaThe aim of the following paper was to gather current scientific information about the analytical protocols dedicated to measuring the content level of short-chain chlorinated paraffins (SCCPs) in various types of environmental samples. Moreover, the data about the basic validation parameters of applied procedures for SCCPs determination are listed. The main issue which is highlighted in the paper is the possibility of the application...
-
Collision Strengths of Astrophysical Interest for Multiply Charged Ions
PublikacjaThe electron impact excitation and ionization processes are crucial for modeling the spectra of different astrophysical objects, from atmospheres of late-type stars to remnants of supernovae and up to the light emission from neutron star mergers, to name just a few. Despite their signifi- cance, however, little is known quantitatively about these processes for low- and medium-impact energies of, say, Ekin . 5000 eV of the free...
-
High-Temperature Tensile Behaviour of GTAW Joints of P92 Steel and Alloy 617 for Two Different Fillers
PublikacjaThis study explores the high-temperature (HT) tensile rupture characteristics of a dissimilar gas-tungsten-arc-welded (GTAW) joint between P92 steel and Alloy 617, fabricated using ER62SB9 and ERNiCrCoMo-1 fillers. The high-temperature tensile tests were performed at elevated temperatures of 550 ◦C and 650 ◦C. An optical microscope (OM) and a field emission scanning electron microscope (FESEM) were utilized to characterize the...
-
Dynamic analysis of the railway bridge span under moving loads
PublikacjaThe first part of this paper provides a review of the state of knowledge of the dynamic behaviour of railway bridges under moving loads. Particular attention is paid to developments in modelling railway bridge loading and dynamic vehicle-span (structure) interaction. The most important aspects determining the advancements in this area of knowledge are identified. The contemporary techniques for defining bridge span finite element...
-
Microstructure and Dielectric Properties of Barium-vanadate Glasses
PublikacjaThe ac and dc conductivity in barium-vanadate glasses was investigated as a function of temperature and frequency with the use of impedance spectroscopy. The topography and microstructure of glasses were investigated by the means of X-ray diffraction (XRD) and scanning electron microscopy (SEM) methods. The XRD results show that all samples are amorphous but microscopy investigation reveals that glasses with greater amount of V2O5...
-
Open-transistor fault diagnostics in voltage-source inverters by analyzing the load current
PublikacjaA novel method is presented for the detection andisolation of open-transistor faults in voltage-source invertersfeeding low-power AC motors. The method is based onmonitoring two diagnostic signals, one indicating sustained nearzerovalues of output current and thus permitting fault detection,the other permitting the isolation of the particular transistorwhich went faulty. The latter signal is the ratio of the averagephase current...
-
Calculation methods of interaction of electromagnetic waves with objects of complex geometries
PublikacjaModeling of the electromagnetic interaction with different homogeneous or inhomo-geneous objects is a fundamental and important problem. It is relatively easy to solve Maxwellequations analytically when the scattering object is spherical or cylindrical, for example. How-ever, when it loses these properties all that is left for us is to useapproximation models, to ac-quire the solution we need. Modeling of complex, non-spherical,...
-
Uncertainty estimation of loop impedance measurement determined by the vector method
PublikacjaThis article presents a detailed analysis of uncertainty estimation of loop impedance measurement determined by the vector method. The analysis includes the following estimates: resistance variance, voltage variance and time measurement variance. This paper presents a methodology for estimating the combined standard uncertainty of loop impedance by the vector method. The vector method allows to determine loop impedance based on...
-
Measurement methods for assessing insulation condition of underground pipelines
PublikacjaThe paper discusses the most frequently applied measurement methods for assessing the quality of external insulation along pipelines and detecting defect locations in the protective coating. The quality of coating along a given pipeline section under investigation is assessed by determining unitary resistance of the coating, which is calculated on the basis of measurement results obtained along a pipeline subjected to cathodic...
-
Metody Admission Control oparte na pomiarach.
PublikacjaSterowanie przyjęciem zgłoszenia jest kluczowym elementem sterowania domeną DiffServ warunkującym świadczenie przez operatora usług z IP QoS. Zasadniczym celem pracy jest dokonanie analizy związanej z metodami AC opartymi na pomiarach określanych skrótem MBAC. Scharakteryzowane zostało sześć metod realizacji MBAC o różnej złożoności obliczeniowej i pomiarowej. Przedstawiona została także realizacja procesu pomiaro-wego wielkości...
-
Research of Emergency Modes of Wind Power Plants Using Computer Simulation
PublikacjaThe aim of this study is to investigate changes in the wind power plant energy production parameters under the conditions of sudden wind changes and voltage drop. To achieve these goals, a simulation of operation of wind power plants was performed. Twelve wind turbines with variable rotational speed equipped with a Fuhrländer FL 2500/104 asynchronous double-fed induction generator (DFIG) were used, each with an installed capacity...
-
Microbial diversity of inflamed and noninflamed gut biopsy tissues in inflammatory bowel disease.
PublikacjaBACKGROUND: Inflammatory bowel disease (IBD) is a chronic gastrointestinal condition without any known cause or cure. An imbalance in normal gut biota has been identified as an important factor in the inflammatory process. METHODS: Fifty-eight biopsies from Crohn's disease (CD, n = 10), ulcerative colitis (UC, n = 15), and healthy controls (n = 16) were taken from a population-based case-control study. Automated ribosomal intergenic...
-
Reactions of cobalt(ii) chloride and cobalt(ii) acetate with hemisalen-type ligands: ligand transformation, oxidation of cobalt and complex formation. Preliminary study on the cytotoxicity of Co(ii) and Co(iii) hemisalen complexes
PublikacjaSeveral molecular cobalt(II) complexes, one Co(II) coordination polymer, and one ionic cobalt(III) complex with imine hemisalen ligands were synthesized. The hemisalen ligands were synthesized from o-vanillin (oVP) and diverse aminopyridines (compounds HL1–HL4) or aminophenol (compound HL5). It was observed that cobalt(II) chloride in dry acetonitrile catalyzes a transformation of HL1 and HL3 instead of complex formation. The conversion...
-
Spatial Distribution of Eucalyptus Plantation and its Impact on the Depletion of Groundwater Resources of Tehsil Swat Ranizai, District Malakand
PublikacjaNative to the continent of Australia, eucalyptus is a tall, evergreen tree belonging to the Myrtaceae family. Malakand district has the largest eucalyptus plantation in the province, covering an area of 22,071.29 ha. The present study aims to evaluate its impact on the groundwater table (GWT) in three selected union councils (UCs) of the study area, i.e., Agra, Totakan, and Kot. Both primary and secondary data support the study....
-
Metal-organic frameworks (MOF) based heat transfer: A comprehensive review
PublikacjaHigher than a standard level, the humidity provides a suitable environment for the pathogenic microorganisms to grow and increases energy consumption for cooling, increasing greenhouse gas emissions. Desiccant air-conditioning (DAC) is an effective method to reduce humidity and energy simultaneously. Conventional desiccants are not suitable for use as a desiccant in building air conditioners, mainly because of high regeneration...
-
Assessment of the Accuracy of Determining the Angular Position of the Unmanned Bathymetric Surveying Vehicle Based on the Sea Horizon Image
PublikacjaThe paper presents the results of research on assessing the accuracy of angular position measurement relative to the sea horizon using a camera mounted on an unmanned bathymetric surveying vehicle of the Unmanned Surface Vehicle (USV) or Unmanned Aerial Vehicle (UAV) type. The first part of the article presents the essence of the problem. The rules of taking the angular position of the vehicle into account in bathymetric surveys...
-
A Computationally Efficient Model for Predicting Successful Memory Encoding Using Machine-Learning-based EEG Channel Selection
PublikacjaComputational cost is an important consideration for memory encoding prediction models that use data from dozens of implanted electrodes. We propose a method to reduce computational expense by selecting a subset of all the electrodes to build the prediction model. The electrodes were selected based on their likelihood of measuring brain activity useful for predicting memory encoding better than chance (in terms of AUC). A logistic...
-
Structural insights, biocatalytic characteristics, and application prospects of lignin-modifying enzymes for sustainable biotechnology
PublikacjaLignin modifying enzymes (LMEs) have gained widespread recognition in depolymerization of lignin polymers by oxidative cleavage. LMEs are a robust class of biocatalysts that include lignin peroxidase (LiP), manganese peroxidase (MnP), versatile peroxidase (VP), laccase (LAC), and dye-decolorizing peroxidase (DyP). Members of the LMEs family act on phenolic, non-phenolic substrates and have been widely researched for valorization...
-
The correlation between nutritional and health potential and antioxidant properties of raw edible oils from cultivated and wild plants
PublikacjaThe nutritional properties and health potential of oils from 15 various cultivated and wild plants were investigated on the basis of the fatty acids profiles, total carotenoids and tocopherols content, antioxidant properties and health potential indexes such as atherogenicity index (AI). The oil contents of the plants varied between 0.9 g/100 g for lychee seeds and 29.7 g/100 g for borage seeds. The tocopherol content in oils ranged...