Filtry
wszystkich: 703
wybranych: 577
Wyniki wyszukiwania dla: NIOBIUM-DOPED
-
Structural and electrochemical heterogeneities of boron-doped diamond surfaces
PublikacjaThis brief review is focussed on the recent progress in studies of the heterogeneous electrochemical behaviour of various boron-doped materials extending from zero-dimensional particles through polycrystalline or nanostructured three-dimensional surfaces. A boron-doped diamond reveals large heterogeneities induced by numerous factors, inter alia multi-faceted crystallinity, inhomogeneous boron concentration, sp2/sp3-carbon ratio,...
-
Visible light activity and photoelectrochemical properties of nitrogen-doped TiO2.
PublikacjaFotokatalizatory TiO2 domieszkowane azotem zostały zsyntetyzowane z propanolanu tytanu (IV) lub chlorku tytanu (IV) i tiomocznika. Żółte proszki otrzymane po ogrzewaniu w temperaturach 400-600 st.C fotokatalizowały mineralizację 4-chlorofenolu w zakresie światła widzialnego (delta większe lub równe 455nm. W odróżnieniu od uprzednio opublikowanych wyników, zsyntetyzowane fotokatalizatory nie zawierały siarki, lecz zamiast tego azot...
-
Electrical conductivity of nanocrystalline Sm-doped CeO2 thin film.
PublikacjaGęste i nanokrystaliczne filmy tlenku ceru domieszkowane 20% samarem przygotowane na szafirze oraz próbki ceramiczne zostały przygotowane z prekursorów polimerowych. Ich konduktacja elektryczna była badana w funkcji temperatury i skorelowana z wielkością krystalitów. Model blokowo-warstwowy przewiduje mniejszą konduktacje próbki gdy wielkości krystalitów są mniejsze, w przypadku gdy rezystancja obszarów międzyziarnowych jest większa...
-
Nanocrystalline doped zirconia and ceria films for fuel cell application
PublikacjaW artykule przedstawiono i porównano właściwości nanokrystalicznych warstw ceramicznych przygotowanych na bazie tlenku ceru i tlenku cyrkonu.
-
Low-temperature spectroscopic and scintillation characterisation of Ti-doped Al2O3
Publikacja -
Studies on optical transmittance of boron-doped nanocrystalline diamond films
PublikacjaThickness is one of the most important parameters in many applications using thin layers. This article describes thickness determination of a boron-doped nanocrystalline diamond (NCD) grown on fused silica glass. A spectroscopic measurement system has been used. A high refractive index (2.3 at 550nm) was achieved for NCD films. The thickness of NCD samples has been determined from the transmission spectrum.
-
Nitrogen-Doped Diamond Film for Optical Investigation of Hemoglobin Concentration
PublikacjaIn this work we present the fabrication and characterization of a diamond film which can be utilized in the construction of optical sensors for the investigation of biological samples. We produced a nitrogen-doped diamond (NDD) film using a microwave plasma enhanced chemical vapor deposition (MWPECVD) system. The NDD film was investigated with the use of scanning electron microscopy (SEM), atomic force microscopy (AFM) and Raman...
-
Structural and thermal characteristics of Ni-doped carbosils prepared by mechanochemistry
Publikacja -
Luminescence properties of Eu3+ and Tb3+ doped silica-based xerogels
PublikacjaPure SiO2 xerogels and SiO2 xerogels containing SrF2: Eu3+/: Tb3+ crystals were prepared using sol-gel method. Luminescent spectra showed excitation and emission peaks characteristic to Eu3+ and Tb3+ 4f - 4f transitions. ET Tb3+→Eu3+ has been observed. XRD pattern of SiO2 matrix confirmed lack of long range order. Patterns of SiO2-SrF2:Eu3+ and SiO2-SrF2:Tb3+ showed peaks corresponding to SrF2. SEM images have shown agglomerates...
-
Pr-doped TiO2: The effect of metal content on photocatalytic activity
PublikacjaThe Pr-TiO2 nanoparticles were prepared by using the sol-gel method. As-prepared samples were characterized by BET measurements, X-ray powder diffraction analysis (XRD) and UV-Vis spectra. Visible and ultraviolet light photocatalytic activity of the sample was studied by photodegradation of phenol while considering the influence of the dopant concentration. TiO2 doped with 0.25 mol% of praseodymium showed the highest photocatalytic...
-
Luminescent properties of Ln3+ doped tellurite glasses containing AlF3
PublikacjaThe low-phonon energy tellurite glasses TeO2-BaO-Bi2O3 and TeO2-BaO-Bi2O3-AlF3 triply doped with Eu3+, Tb3+, Tm3+ ions in two different molar ratios were synthesized using melt-quenching technique. Their structure and luminescence properties were widely investigated by X-ray Diffraction (XRD), Differential Scanning Calorimetry (DSC), Fourier Transform Infrared Spectroscopy (FTIR) and Photoluminescence Spectroscopy (PL). The luminescence...
-
Microwave solvothermal synthesis and characterization of manganese-doped ZnO nanoparticles
Publikacja -
High pressure studies of Eu2+ and Mn2+ doped NaScSi2O6 clinopyroxenes
Publikacja -
In-situ optical diagnostics of boron-doped diamond films growth
PublikacjaInterferometry is a desirable method for in-situ measurement of thin, dielectric film growth, as it don't modify conditions of film deposition. Here we present interferometrical measurements of thickness of doped diamond films during Chemical Vapor Deposition (CVD) process. For this purpose we used a semiconductor laser with a 405nm wavelength. Additional ex-situ measurement using spectral interferometry and ellipsometry...
-
Luminescence and energy-storage properties of Pr3+-doped YAlO3 crystals
Publikacja -
OSL and RL of LiMgPO4 crystals doped with rare earth elements
Publikacja -
Boron-doped TiO2: Characteristics and photoactivity under visible light
PublikacjaOtrzymano TiO2 domieszkowany borem aktywny w reakcjach fotodegradacji pod wpływem światła widzialnego (λ>400 nm). Fotokatalizatory otrzymano poprzez hydrolizę tytanianu(IV) izopropylu w obecności związków boru lub poprzez ucieranie TiO2 (ST-01, P25 i A11) z prekursorami B i następnie kalcynację w zakresie temperatur 200-600oC. Jako źródło boru zastosowano kwas borowy lub ester trietylowy kwasu borowego. Najwyższą aktywność pod...
-
Chemical characteristics of new nanopowder of titania doped with nitrogen atoms
PublikacjaW pracy zaprezentowano charakterystykę domieszkowanego azotem ditlenku tytanu otrzymanego na drodze jednoetapowej syntezy z kompleksu tytanu (IV) z ligandami zawierającymi atomy azotu. ikrostruktura i morfologia nowego materiału została określony za pomocą badań XRD, AFM, UV-VIS i FT-IR. Raport przedstawia również badania elektrochemiczne, które pozowliły na wyznaczenie potencjału pasma płaskiego na podstawie wykresu Mott
-
Synthesis of acceptor-doped Ba-Ce-Zr-O perovskites
PublikacjaPublikacja przedstawia wyniki badań stukturalnych i elektrycznych domieszkowanego akceptorow cerianu baru.
-
Nanocrystalline doped zirconia and ceria films for fuel cell application
PublikacjaW artykule przestawiono porównanie właścowości warstw nanokrystalicznych przygotowanych w technologii 'net-shape'. Materiały te mają zastosowanie w tlenkowychogniwach paliwowych.
-
Breakdown of Adiabatic Superconductivity in Ca-Doped h-BN Monolayer
Publikacja -
Oxide nanoparticle exsolution in Lu-doped (Ba,La)CoO3
Publikacja -
Photocatalytic activity and surface properties of carbon-doped titanium dioxide
PublikacjaTiO2 domieszkowany węglem otrzymano poprzez hydrolizę izopropanolanu tytanu(IV) i kalcynację w 350ºC w atmosferze powietrza przez 2h. Przeprowadzone badania wykazały, że fenol (0.21 mM) jest efektywnie degradowany w fazie wodnej, w obecności otrzymanego fotokatalizatora oraz światła z zakresu widzialnego (λ>400 nm). Pole powierzchni właściwej otrzymanego C-TiO2 wynosiło około 127 m2/g, fotokatalizator absorbuje światło z zakresu...
-
Optical properties of daylight curable resin doped with nanodiamond powder
PublikacjaIn this paper a new material for 3D printing was elaborated on. Since diamond has very good optical properties, an idea occurred to us to apply it in 3D printing process. A mixture of nanodiamond powder and a standard 3D printing resin was created and several printouts have been completed. They have been tested for their abilities to transmit and absorb light in a wide spectrum of wavelengths. It turned out that the nanopowder...
-
N-doped carbon materials as electrodes for highly stable supercapacitors
PublikacjaThis article reports a strategy to use nitrogen-doped carbon materials as electrodes for supercapacitors. Depending on the carbon precursor, the porous structure is changed with specific surface area reached up to 2270 m2 g−1. The capacitance of carbon materials used as electrodes is related strictly to pore size. The microstructure and nitrogen functionalities enable a high capacitance (327 F g−1) and cycle durability. The nanoporous...
-
Oxide nanoparticle exsolution in Lu-doped (Ba,La)CoO3
PublikacjaThis study investigated Lu doping of Ba0.5La0.5CoO3 and its influence on the exsolution of oxide nanoparticles (NPs). As a result of Lu doping, we observed the phase segregation into the main Ba0.4La0.6Co0.85Lu0.15O3 (BLCO–Lu) phase and the secondary Ba0.85La0.15Co0.75Lu0.25O3 (BCO–Lu) phase. We noticed the exsolution of BCO–Lu nanoparticles on the main BLCO–Lu phase. Moreover, the BLCO–Lu phase exsolved in the form of nanoparticles...
-
Structure and transport properties of donor-doped barium strontium cobaltites
PublikacjaIn this work, Nb-substituted barium strontium cobaltites Ba0.5Sr0.5Co1-xNbxO3-δ (x = 0 – 0.4) have been fabricated and studied. The structural analysis showed that the Nb content influences the lattice constant as well as the distance between the (Co, Nb) and oxygen atoms. The study of morphology of samples showed that the Nb content does not change the porosity, grain size and morphology of the ceramics. The total electrical conductivity...
-
The activity of fused-iron catalyst doped with lithium oxide for ammonia synthesis
Publikacja -
Optoelectronic and non-linear optical properties of Lu-doped AgGaGe3Se8 crystallites
Publikacja -
Weak antilocalization effect and triply degenerate state in Cu-doped CaAuAs
Publikacja -
Electrochemical oxidation of ionic liquids at highly boron doped diamond electrodes
Publikacja -
Local impedance imaging of boron-doped polycrystalline diamond thin films
Publikacja -
Characterization of magnesium doped lanthanum orthoniobate synthesized by molten salt route
PublikacjaMolten salt synthesis method has been used to prepare the single phase magnesium doped lanthanum orthoniobate. The phase composition has been checked by X-ray diffraction method and the microstructure studies have been performed by scanning electron microscopy. The high temperature properties of the material have been investigated by thermogravimetry and electrochemical impedance spectroscopy. A dependence between sample total...
-
Magnetic field mapping along a NV-rich nanodiamond-doped fiber
PublikacjaIntegration of NV−-rich diamond with optical fibers enables guiding quantum information on the spin state of the NV− color center. Diamond-functionalized optical fiber sensors have been demonstrated with impressive sub-nanotesla magnetic field sensitivities over localized magnetic field sources, but their potential for distributed sensing remains unexplored. The volumetric incorporation of diamonds into the optical fiber core allows...
-
Electrical properties of A-site Ca-doped LaNb1-xAsxO4-δ ceramics
PublikacjaThe electrical properties of A-site Ca-doped LaNbO4 with the addition of As in the B-site, have been investigated. Total, grain- and specific grain boundary electric conductivities in different oxygen partial pressure, and water vapour partial pressure were determined. Additional conductivity measurements were performed in nitrogen, to suppress the possible p-type conductivity, focusing on protonic conductivity. The maximum measured...
-
Future hosts for fast and high light output cerium-doped scintillator
Publikacja -
Optical and Electrical Properties of Iodine Doped n-Type ZnSe Crystals
Publikacja -
Application of non-metal doped titania for inverted polymer solar cells
PublikacjaDomieszkowany jodem oraz domieszkowany jodem ditlenek tytanu uzyto jako warstwę buforową w ogniwie ITO/X-TiO2?P3HT-PCMB /MnO2/ Ag.Warswty X-TiO2 nalożono metodą spin-coatingu z zawiesiny nanocząstek w DMSO. Jednorodne struktury scharakteryzowane pod względem morfologii mikroskopowo metodą AFM. Charakterystyka prądowo-napięciowa urzdzeń wskazuje iż domieszkowany jodem TiO2 pozwala osiągnąć lepsze parametry PCE (1,67%) i prąd zwarcia...
-
Structural and electrical properties of Cr-doped SrTiO 3 porous materials
PublikacjaSeries of single-phase materials with assumed formula SrTi1−xCrxO3 (where x = 0, 1, 4, 6 mol.%) were obtained by sol-gel method. The structure and microstructure of materials were characterised by X-ray diffraction and scanning electron microscopy methods. Moreover, the study of electrical properties and evaluation of chemical stability in CO2/H2O atmosphere was performed by electrochemical impedance spectroscopy and thermogravimery...
-
Electrical properties of Na2O-CaO-P2O5 glasses doped with SiO2 and Si3N4
PublikacjaSodium-calcium-phosphate glasses doped with SiO2 or Si3N4 having similar sodium ion concentrations were prepared by melt quenching. The conductivity was measured by impedance spectroscopy under nitrogen atmosphere in a wide frequency range (10 mHz–1 MHz) and wide temperature range (153–473 K). At 36.6 °C, DC conductivities of all glasses vary between 1.1 ∗ 10−12 and 8.9 ∗ 10−12 S cm−1 and have similar activation energies (between...
-
In Vitro Biological Characterization of Silver-Doped Anodic Oxide Coating on Titanium
PublikacjaDespite the high biocompatibility and clinical effectiveness of Ti-based implants, surface functionalization (with complex osteointegrative/antibacterial strategies) is still required. To enhance the dental implant surface and to provide additional osteoinductive and antibacterial properties, plasma electrolytic oxidation of a pure Ti was performed using a nitrilotriacetic acid (NTA)-based Ag nanoparticles (AgNP)-loaded calcium–phosphate...
-
Signature of Oxide-Ion Conduction in Alkaline-Earth-Metal-Doped Y3GaO6
PublikacjaWe have studied alkaline-earth-metal-doped Y3GaO6 as a new family of oxide-ion conductor. Solid solutions of Y3GaO6 and 2% −Ca2+-, −Sr2+-, and −Ba2+-doped Y3GaO6, i.e., Y(3−0.06)M0.06GaO6−δ (M = Ca2+, Sr2+, and Ba2+), were prepared via a conventional solid-state reaction route. X-ray Rietveld refined diffractograms of all the compositions showed the formation of an orthorhombic structure having the Cmc21 space group. Scanning electron...
-
Gigantic electro-chemo-mechanical properties of nanostructured praseodymium doped ceria
PublikacjaSome oxygen defective fluorites are non-Newnham electrostrictors, i.e., the electromechanical response does not depend on their dielectric properties. Here, we show gigantic electrostriction in nanocrystalline 25 mol% praseodymium doped ceria (PCO) bulk ceramics. The material was fabricated with a fieldassisted spark plasma sintering (SPS) process from high-purity nanoscale PCO powders (<20 nm). The SPS process consolidates the...
-
Photocatalytic ozonation using doped TiO2 catalysts for the removal of parabens in water
Publikacja -
Synthesis, microstructure and electrical properties of nanocrystalline calcium doped lanthanum orthoniobate
Publikacja -
Solid phase extraction of explosives on Ni-doped carbosils prepared by mechanochemistry
Publikacja -
Synthesis and characterization of resorcinol–formaldehyde resin chars doped by zinc oxide
Publikacja -
Biophotonic low-coherence sensors with boron-doped diamond thin layer
PublikacjaLow-coherence sensors using Fabry-Perot interferometers are finding new applications in biophotonic sensing, especially due to the rapid technological advances in the development of new materials. In this paper we discuss the possibility of using boron-doped nanodiamond layers to protect mirror in a Fabry-Perot interferometer. A low-coherence sensor using Fabry-Perot interferometer with a boron-doped nanodiamond (B-NCD) thin protective...
-
Enhanced photoelectrochemical and photocatalytic performance of iodine-doped titania nanotube arrays
PublikacjaThe paper discusses the synthesis and performance of iodine doped titania nanotube arrays exhibited under irradiation. The doping procedure was performed as an additional, electrochemical process carried out after formation of nanotube arrays via anodization of Ti substrate. The optical and structural properties were characterized using Raman, UV-vis, photoluminescence and X-ray photoelectron spectroscopy. The surface morphology...
-
Facile preparation of extremely photoactive boron-doped TiO2 nanotubes arrays
PublikacjaDoping of TiO2 nanotube arrays with boron was realized via electrochemical treatment of as-anodized titania immersed in electrolyte containing boric acid. The photoactivity of doped and pure titania was examined by means of photoelectrochemical and photocatalytic response under UV-vis irradiation. The results showed that photocurrent density of B-TNTs is remarkably higher (7.5 times) than density of pure TiO2 nanotube arrays. Furthermore,...