Filtry
wszystkich: 1204
wybranych: 1093
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: INSULATION CONCRETE
-
The use of GFRP tubes as load-bearing jackets in concrete-composite columns
PublikacjaThe paper presents the fields of applications of polymer composites in building structures. The use of composite glass fibre tubes is discussed in more detail. The laboratory methods used to test the mechanical properties of these pipes are presented. An original research program is presented, including six concrete-filled glass fibre tubes. The cylinders and columns made in this way were tested for their axial load capacity. Conclusions...
-
Effect of coarse grain aggregate on strength parameters of two-stage concrete
Publikacja. Two-stage concrete (TSC) is a special type of concrete that the method of its construction and implementation is different from conventional one. In TSC, coarse aggregate particles are first placed in the formwork and voids between them are subsequently injected with a special cementations mixture. TSC has been successfully used in many applications, such as underwater construction, casting concrete sections congested with reinforcement...
-
Guided Wave Propagation in Detection of Partial Circumferential Debonding in Concrete Structures
PublikacjaThe following article presents results of investigating the damage detection in reinforced concrete beams with artificially introduced debonding between the rod and cover, using a non-destructive method based on elastic waves propagation. The primary aim of the research was to analyze the possible use of guided waves in partial circumferential debonding detection. Guided waves were excited and registered in reinforced concrete...
-
Debonding Detection in Reinforced Concrete Beams with the Use of Guided Wave Propagation
PublikacjaOne of the most frequent damage of the reinforced concrete structures is debonding between steel bar and concrete cover. In the case of debonding occurrence not only the strength of the structure decreases, but also it is more vulnerable to corrosion damages. For this reason fast and effective methods of debonding detection in an early stage of its development need a significant boost. The paper presents analytical and experimental...
-
Safety assessment of a concrete viaduct damaged by vehicle impact and an evaluation of the repair
PublikacjaDamage to lower parts of viaducts caused by impact from under-passing high vehicles is relatively frequent. One such incident, in which a viaduct was damaged by the impact from a truck with an improperly assembled hydraulic crane, is considered in this work. The analysis is based on a detailed object damage evaluation, 3D laser scanning, and numerical simulations. The aim of the study is to accurately model the vehicle impact into...
-
Influence of Actual Curing Conditions on Mechanical Properties of Concrete in Bridge Superstructures
PublikacjaThis article presents the research on the mechanical characteristics of concrete in the construction of three concrete bridges. A system of recording the internal temperature of concrete and automatic control of laboratory ovens was used for specimen curing. This allowed the specimens to be cured under conditions similar to those occurring in the structure. Before the construction, reference blocks were used to define similar curing...
-
Impact of Surfactant and Calcium Sulfate Type on Air-Entraining Effectiveness in Concrete
Publikacja -
REINFORCED CONCRETE SUPPORTING CONSTRUCTION OF THE STADIUM COVER FOR EURO 2012 IN GDAŃSK
PublikacjaIn the article structural issues that connected with the reinforced concrete supporting construction of the stadium roofing for EURO 2012 in Gdańsk were described. In the first part of the article the concept of stadium foundation were described. In the second the static - strength analysis for two variants fastening together individual foundation elements were made. The two assumed geometrically different concept of foundation...
-
COMPUTER-AIDED CONSTRUCTION AT DESIGNING REINFORCED CONCRETE COLUMNS AS PER EC
PublikacjaThe article presents the author’s computer program for designing and dimensioning columns in reinforced concrete structures taking into account phenomena affecting their behaviour and information referring to design as per EC. The computer program was developed with the use of C++ programming language. The program guides the user through particular dimensioning stages: from introducing basic data such as dimensions, concrete...
-
A novel formulation of 3D spectral element for wave propagation in reinforced concrete
PublikacjaThe paper deals with numerical simulations of wave propagation in reinforced concrete for damage detection purposes. A novel formulation of a 3D spectral element was proposed. The reinforcement modelled as the truss spectral element was embedded in the 3D solid spectral finite element. Numerical simulations have been conducted on cuboid concrete specimens reinforced with two steel bars. Different degradation models were considered...
-
High Rise Building: The Mega Sculpture Made Of Steel, Concrete and Glass
PublikacjaHigh rise building has transformed from providing not only the expansion of floor space but functioning as mega sculpture in the city. The shift away from economic efficiency driven need is only expected to grow in the future. Based on literature studies; after analysing planning documents and case studies, it was examined whether the presumption that gaining the maximum amount of usable area is the only driving factor; or if the...
-
Numerical modeling of GPR field in damage detection of a reinforced concrete footbridge
PublikacjaThe paper presents a study on the use of the ground penetrating radar (GPR) method in diagnostics of a footbridge. It contains experimental investigations and numerical analyses of the electromagnetic field propagation using the finite difference time domain method (FDTD). The object of research was a reinforced concrete footbridge over a railway line. The calculations of the GPR field propagation were performed on a selected cross-section...
-
Model-Based Adaptive Machine Learning Approach in Concrete Mix Design
PublikacjaConcrete mix design is one of the most critical issues in concrete technology. This process aims to create a concrete mix which helps deliver concrete with desired features and quality. Contemporary requirements for concrete concern not only its structural properties, but also increasingly its production process and environmental friendliness, forcing concrete producers to use both chemically and technologically complex concrete...
-
BEHAVIOR OF REINFORCED CONCRETE BEAMS CONTAINING LIGHTWEIGHT AGGREGATE IN THE TENSILE ZONE
Publikacja.
-
The Influence of the Aircraft Operating Fluids on the Mechanical Parameters of the Airport Surface Concrete
PublikacjaThe authors of the article assessed the impact of operating fluids used to service aircraft on changing mechanical parameters of cement concrete intended for airport pavement. The research concerned concrete designed with the use of CEM I 42.5N LH NA low-alkali cement, broken granite aggregate, fine washed aggregate, and admixtures. The analysis included the assessment of changes in dierences in endurance parameters over various...
-
Structural Assessment of Reinforced Concrete Beams Incorporating Waste Plastic Straws
PublikacjaThe behavior of reinforced concrete beams containing fibers made of waste plastic straws (WPSs) under the three point bending test is examined. The effect of WPS fiber addition on the compressive and split tensile strength is reported. Four concrete mixes were prepared. The control mix PS-0 had a proportion of 1 cement: 1 sand: 2 coarse aggregate and a water cement ratio of 0.4. In the other three mixes PS-0.5, PS-1.5 and PS-3,...
-
Experimental and Numerical Investigations of the Effect of Curing Conditions on the Temperature Rise of Concrete
PublikacjaThis paper presents experimental and numerical studies investigating the impact of three curing conditions on temperature evolution in concrete cubes. The tests were performed on samples of the same volume (3.375 dm3) under different curing conditions: room temperature, insulation boxes, and adiabatic calorimeter. Various cements (Portland cement, Portland composite cement, and blast furnace slag cement) and aggregates (gravel...
-
Influence of the Addition of Recycled Aggregates and Polymer Fibers on the Properties of Pervious Concrete
PublikacjaThe aim of the study was to check the possibility of reusing aggregate from recycled concrete waste and rubber granules from car tires as partial substitution of natural aggregate. The main objective was to investigate the effects of recycled waste aggregate modified with polymer fibers on the compressive and flexural strength, modulus of elasticity and permeability of pervious concrete. Fibers with a multifilament structure and...
-
Evaluation of reinforcement corrosion rate in concrete structures by electrochemical noise measurements
PublikacjaW pracy przedstawiono wyniki obliczeń rezystancji polaryzacyjnej w układzie złożonym z dwóch elektrod (ze stali węglowej oraz elektrody odniesienia), umieszczonych w otulinie betonowej. Szybkość korozji ulega zmianom uzależnionym od stopnia nasiąknięcia betonu roztworem zawierającym jony chlorkowe. Zmiany rezystancji polaryzacyjnej elektrody stalowej oceniane są na podstawie pomiarów prądowego i potencjałowego szumu elektrochemicznego....
-
Modeling of capillary fluid flow in concrete using a DEM-CFD approach
PublikacjaSformułowano połączone podejście do modelowania dwufazowego przepływu wody napędzanego hydraulicznie i kapilarnie w nienasyconym betonie. Proces przepływu analizowano numerycznie w mezoskali w warunkach dwuwymiarowych (2D), łącząc metodę elementów dyskretnych (DEM) z obliczeniową dynamiką płynów (CFD) w warunkach izotermicznych. Przeprowadzono w pełni sprzężone hydromechaniczne testy symulacyjne na małych próbkach betonu o uproszczonej...
-
Investigations of size effect in tensile fracture of concrete using a lattice model
PublikacjaArtykuł przedstawia symulacje efektu skali w betonie podczas rozciągania przy zastosowaniu nowego modelu siatkowego. Zbadano wpływ rozkładu i wielkości kruszywa oraz wpływ strefy kontaktu na efekt skali.
-
J. FE modelling of cracks in concrete elements within continuum mechanics.
PublikacjaW artykule przedstawiono wyniki symulacji rys zakrzywionych w elementach betonowych w warunkach mieszanego sposobu obciążenia. Symulacje wykonano przy zastosowaniu 3 różnych modeli: modelu sprężysto-plastycznego, modelu w ramach mechaniki zniszczeniowej i modelu z rysami obracającymi się.
-
Multi-scale modelling of concrete beams subjected to three-point bending
PublikacjaW artykule przedstawiono wyniki numeryczne MES dwuskalowego modelowania belek betonowych z nacięciem na poziomie skali makro i mezo. Obliczenia wykonano przy wykorzystaniu modelu degradacji sztywności z nielokalnym osłabieniem. Beton został opisany na poziomie skali mezo jako stochastyczny materiał 3-składnikowy złożony z kruszywa, zaczynu cementowego oraz stref kontaktu. Natomiast na poziomie skali makro został opisany jako materiał...
-
FE-modelling of strain localization in concrete with coupled elasto-plasticity and damage
PublikacjaW artykule przedstawiono wyniki numerycznej dla zginania belki betonowej przy zastosowaniu modelu sprężysto-plastycznego, modelu z degradacja sztywności i modelu połączonego sprężysto-plastycznego z degradacją sztywności. Wszystkie modele rozszerzono o długość charakterystyczną mikrostruktury za pomocą teorii nielokalnej.
-
Application of DIC technique to concrete - study on objectivity of measured surface displacements
PublikacjaArtykuł omawia wyniki pomiarów szerokości lokalizacji odkształceń na powierzchni betonu podczas zginania belek. Wykonano obszerne studia nad obiektywnością pomierzonych przemieszczeń w betonie. Opracowano własna metodę do obliczeń szerokości lokalizacji.
-
Experimental investigations of size effect in reinforced concrete beams failing by shear
PublikacjaW artykule omówiono wyniki doświadczalne efektu skali w zbrojonych betonowych belkach niszczących się przez ścinanie. Doświadczenia wykonano dla belek o różnych wymiarach ze zbrojeniem stalowym i bazaltowym. Podczas doświadczeń pomierzono siłę oraz szerokości lokalizacji i rys. Wyniki porównano z modelem skali wg Bazanta.
-
Early prediction of macrocrack location in concrete and other granular composite materials
PublikacjaHeterogeniczne kruche kompozyty, takie jak beton, ceramika i skały składają się z ziaren połączonych wiązaniami. Pytanie, czy ścieżka pęknięcia, która prowadzi do zniszczenia może być przewidziania na podstawie znanych cech mikrostrukturalnych, a mianowicie łączności wiązań, rozmiaru, energii pękania, wytrzymałości pozostają otwarte. Istnieje wiele kryteriów pęknięć. Najczęściej używane są oparte na postulowanym ekstremum naprężenia...
-
Numerical analysis of behaviour of reinforced concrete elements under eccentric compression
PublikacjaPrzedstawiono wyniki modelowania nośności elementów żelbetowych stosując metodę elementów skończonych. Do opisu betonu zastosowano sprężysto-plastyczne prawo materiałowe wg Druckera-Pragera. Do modelowania stali zbrojeniowej zastosowano sprężysto-plastyczne prawo materiałowe według von Misesa. Obliczenia wykonano dla ścian żelbetowych.
-
A Non-local elasto-plastic model to describe localisations of deformation in concrete
PublikacjaPrzedstawiono wyniki numerycznej symulacji lokalizacji odkształceń stosując metodę elementów skończonych na bazie nielokalnego prawa sprężysto-plastycznego dla betonu. Prawo wykorzystuje długość charakterystyczną. Obliczenia dla ściskania jednoosiowego pokazały, że wyniki numeryczne nie zależą od siatki MES. Osiągnięto pełną regularyzację problemu brzegowego.
-
Are firefighters able to perform blind endotracheal intubation via LMA Fastrach? An experimental study
Publikacja -
Wireless Body Area Network for Preventing Self-Inoculation Transmission of Respiratory Viral Diseases
PublikacjaThis paper proposes an idea of Wireless Body Area Networks (WBANs) based on Bluetooth Low-Energy (BLE) standards to recognize and alarm a gesture of touching the face, and in effect, to prevent self-inoculation of respiratory viral diseases, such as COVID-19 or influenza A, B, or C. The proposed network comprises wireless modules placed in bracelets and a necklace. It relies on the received signal strength indicator (RSSI) measurements...
-
New high-gain step-up DC/DC converter with high-frequency isolation
Publikacja -
Polymeric Bearings as a new base isolation system suitable for mitigating machine-induced vibrations
PublikacjaThe present paper summarizes the preliminary results of the experimental shaking table investigation conducted in order to verify the effectiveness of a new base isolation system consisting of Polymeric Bearings in reducing strong horizontal machine-induced vibrations. Polymeric Bearing considered in the present study is a prototype base isolation system, which was constructed with the use of a specially prepared flexible polymer...
-
CONSUMERS’ APPROACH TO THE CREDIBILITY OF THE INFLATION FORECASTS PUBLISHED BY CENTRAL BANKS: A NEW METHODOLOGICAL SOLUTION
PublikacjaModern monetary policy focuses on credibility and shaping inflation expectations. In keeping with the concept of inflation forecast targeting, the inflation forecasts published by central banks play a crucial role in the instrument rate decision-making process and may be treated as a specific intermediate target. This study proposes an inflation forecast credibility index, the scope of which is narrowed to non-specialists’ approach...
-
When all we have is not enough: a search for the optimal method of quantifying inflation expectations
PublikacjaAlthough inflation expectations are pivotal variables for central banks, they are not directly observable. Therefore, central banks use qualitative survey results to proxy consumer expectations, and their quantification in this manner is often criticized. In this study, we investigate and identify an optimal quantification procedure for survey results based on a set of regression and probabilistic models. Specifically, we seek...
-
Chemometric Method of Spectra Analysis Leading to Isolation of Lysozyme and CtDNA Spectra Affected by Osmolytes
PublikacjaW niniejszej pracy zaprezentowana została chemometryczna metoda analizy danych widmowych, prowadząca do wyizolowania widm FTIR biomakrocząsteczek (lizozymu z białka jaja kurzego i ctDNA) zaburzonych przez wybrane osmolity (TMAO, betainę) w roztworach wodnych. Została ona oparta na metodzie widm różnicowych, wykorzystywanej pierwotnie do określania struktury rozpuszczalnika wokół cząsteczek substancji rozpuszczonej. Cykliczne wykorzystanie...
-
Polymeric Bearings – A New Base Isolation System to Reduce Structural Damage during Earthquakes
PublikacjaBase isolators, like lead rubber bearings, high damping rubber bearings or friction pendulum systems are extensively used in practice in many seismically active regions to protect structures against earthquake forces. The present paper reports the results obtained from the experimental study aimed to determine the effectiveness of the Polymeric Bearings in suppressing structural vibrations during dynamic excitations and therefore...
-
Can Inflation Forecast and Monetary Policy Path be Really Useful? The Case of the Czech Republic
PublikacjaProducing and revealing inflation forecast is belie ved to be the best way of implementing a forward-looking monetary policy. The article focuses on inflation forecast targeting (IFT) at the Czech National Bank (CNB) in terms of its efficiency in shaping consumers’ inflation expectations. The goal of the study is to verify the accuracy of the inflation forecasts, and their influence on inflation...
-
Isolation and some properties of the thermostable beta-galactosidase of Pyrococcus woesei expressed in Escherichia coli
PublikacjaOpracowano metodę izolowania oraz zbadano właściwości enzymu otrzymanego ze szczepu Escherichia coli zawierającego gen kodujący termostabilną beta-ga-laktozydazę z Pyrococcus woesei.
-
Isolation of Citrus lemon extracellular vesicles: Development and process control using capillary electrophoresis
PublikacjaA new and scalable method for the isolation of extracellular vesicles (EV) from Citrus lemon juice samples was developed. The methodology included preliminary preconcentration of the sample using ultrafiltration (UF) followed by size-exclusion chromatography (SEC) purification and final preconcentration of the eluates. Transmission electron microscopy and proteomic analysis showed that isolates contained exosome-like vesicles, exocyst-positive...
-
Thermal visualization of Ostwald-de Waele liquid in wavy trapezoidal cavity: Effect of undulation and amplitude
Publikacja -
Inhalation risk to PAHs and BTEX during barbecuing: The role of fuel/food type and route of exposure
Publikacja -
Consideration of the safety of bungee jumping in relation to mechanical properties of the instalation based on a jump accident in Gdynia
PublikacjaThis paper considers a bungee jumping accident that took place in July 2019 in Gdynia, Poland. The authors conducted an investigation to determine the cause of the bungee rope failure. It was based on mechanical tests concerning the strength of the rope as well as the calculation of the force induced in the rope during the jump. Based on the theoretical and experimental results, the rope safety factor was estimated. It appeared...
-
Thermal visualization of Ostwald-de Waele liquid in wavy trapezoidal cavity: Effect of undulation and amplitude
PublikacjaThe present study is concerned with the numerical simulations of Ostwald-de Waele fluid flow in a wavy trapezoidal cavity in the presence of a heated cylinder situated at the center of the cavity. The work consists in characterizing the mixed convection as a function of the intensity of heat flow. The flow behaviour and temperature distribution in a cavity are the main focus of this study. The lower wall of the cavity is fixed...
-
Investigation of Durability Properties for Lightweight Structural Concrete with Hemp Shives Instead of Aggregate
Publikacja -
Effect of a characteristic length on crack spacing in a reinforced concrete bar under tension
Publikacja -
The influence of texturing of the surface of concrete substrate on its adhesion to cement mortar overlay
Publikacja -
Experimental Study and Finite Element Modeling of Reinforced Concrete Column Having an Opening
Publikacja -
The quality management in precast concrete production and delivery processes supported by association analysis
Publikacja -
Electrochemical investigations of conductive coatings applied as anodes in cathodic protection of reinforced concrete
Publikacja