wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: : P91 STEEL
-
Simulation of Structure Formation Processes of Dissimilar Steels Welded Joints Using an Intermediate Layer
Publikacja -
The analysis of the mechanical properties of welding joints of high-strength steels for offshore and ships structures
PublikacjaW artykule przedstawiono równania korelacyjne właściwości mechanicznych złaczy spawanych stali wysokiej wytrzymałości, które umożliwiają ocenę wpływu technologii spawania tych stali.W pracy zaproponowana dwa równania. Pierwsze umożliwa wstępną ocenę spawalności obecnie produkowanych stali wysokiej wytrzymałości, natomiast równania korelacyjne pozwalają obliczyć maksymalną twardość strefy wpływu ciepła materiału.
-
Hydrogen-enhanced stress corrosion cracking and corrosion fatigue of HSLA steels in sea-water
PublikacjaPrzedstawiono ocenę podatności stali o wysokiej wytrzymałości na naprężeniowe pękanie korozyjne i zmęczenie korozyjne wspomagane przez wodór. Wykonano próby powolnego rozciągania i zmęczenia niskoczęstotliwościowego na stalach 17HMBVA i 14HNMBCu oraz ich złączach spawanych, w środowisku wody morskiej, przy polaryzacji katodowej. Zamieszczono wyniki badań elektrochemicznych oraz przełomów na skaningowym mikroskopie elektronowym.
-
Kinetics of Intermetallic Phase Precipitation in Manual Metal Arc Welded Duplex Stainless Steels
PublikacjaThe article presents the influence of heat treatment on the kinetics of transformations in lean duplex LDX2101 steel and a weld made of standard duplex 2209 material, which was welded by manual metal arc welding. Changes in the microstructure, hardness, and magnetic phase content were analyzed after heat treatment was conducted at a temperature of 800 °C for a period ranging from 15 to 1440 min. Light and scanning microscopy, Vickers...
-
Effect of wet Hydrogen Sulfide on Carbon Steels Degradation in Refinery Based on Case Study
PublikacjaMaterial degradation caused by wet hydrogen sulfide (Wet H2S) is one of the major issues in refineries. Carbon steel is the main construction material used in refineries and is subjected not only to thickness loss but the hydrogen is the major concern. H2S leads to high atomic hydrogen penetration in steel which causes degradation in the form of blistering and/or cracking (HIC/SOHIC) and stress cracking in the area of welds and...
-
Three-Dimensional Fractography for Conventional and Additive Manufactured Steels After Bending-Torsion Fatigue
PublikacjaIn this study, fracture surface topography parameters were measured to investigate the effects of multiaxial loading. In order to assess the metrological aspects of fracture for notched specimens made of high-strength steels processed by both conventional and additively manufacturing (AM) techniques, an optical surface profilometer was used. Three bending moment to torsion moment ratios (B/T) were studied, i.e. 2, 1 and 2/3. The...
-
Influence of Heat Treatment Temperature on Fatigue Toughness in Medium-Carbon High-Strength Steels
PublikacjaCurrent research has demonstrated that the tempering temperature affects the martensitic transformation of medium-carbon high-strength steels. This temperature plays an important role in the final microstructure, percentage ratios of martensite to ferrite phases and, consequently, in the mechanical properties and the fatigue response. So far, the relationship between the martensitic tempering temperature and the cyclic deformation...
-
Autogenous Fiber Laser Welding of 316L Austenitic and 2304 Lean Duplex Stainless Steels
PublikacjaThis study presents results of experimental tests on quality of dissimilar welded joints between 316L austenitic and 2304 lean duplex stainless steels, welded without ceramic backing. Fiber laser welded butt joints at a thickness of 8 mm were subjected to non‐destructive testing (visual and penetrant), destructive testing (static tensile test, bending test, and microhardness measurements) and structure observations (macro‐ and...
-
Niszczenie wodorowe stali o podwyższonej wytrzymałości = Hydrogen degradation of high-strength steels.
PublikacjaW artykule przedstawiono niszczenie wodorowe stali 18G2A i jej symulowanej strefy wpływu ciepła (SWC). Jako parametry niszczenia wodorowego wybrano względne wartości energii zniszczenia, czasu do pęknięcia, wydłużenia, przewężenia i wytrzymałości na rozciąganie. Parametry te wyznaczono w próbie odkształcania z małą prędkością na próbkach gładkich, okrągłych. Stwierdzono, że stal 18G2A w środowisku kwaśnym (0,1 N H2SO4) podczas...
-
Peptide splicing in a double‐sequence analogue of trypsin inhibitor SFTI‐1 substituted in the P1 positions by peptoid monomers
Publikacja -
The AFM topographic measurements of the surface heterogeneity of iron hexacyanoferrate on a steel surface
Dane BadawczeMeasurements in semi-contact mode. NTEGRA Prima (NT-MDT) device. NSG 01 probe.
-
EH36 steel for shipbuilding - Charpy impact test reslut in vary tempetatures
Dane BadawczeThe basic method of ductility designation of structural steels is the Charpy impact test. The test consists of a single strike of the specimen using a Charpy pendulum. Its result is the value of work necessary to break a specimen at a test temperature. Despite its many advantages, such as its short implementation time and low costs, it has its disadvantages,...
-
The AFM micrographs of pitting corrosion evolution on high-alloy steel 1.4301
Dane BadawczeThe dataset contains the results of topographic imaging of high-alloy stainless steel 1.4301 on which the pitting corrosion process was induced by electrochemical methods. The study of the effects of a local attack allows for conclusions about the intensity and mechanism of this type of corrosion. The file contains atomic force microscopy (AFM) data...
-
The AFM micrographs of austenitic stainless steel subjected to sensitization for intergranular corrosion
Dane BadawczeThe dataset contains atomic force microscopy (AFM) maps of topographic images of austenitic steel samples subjected to sensitization to the process of intergranular corrosion. Precipitations of carbides as well as other intermetallic phases can be observed and detected before the fragments of structures sensitized by improper thermal treatment are exposed...
-
Analysis of electrochemical parameters in time domain during the passive layer cracking occurring on the 304L stainless steel in chlorides solution under tensile stresses
Publikacja -
Analysis of EN 1993-1-6 guidelines about determining amplitudes of equivalent imperfections of steel cylindrical shells subjected to uniform external pressure
PublikacjaCivil engineering structures should be designed with reference to relevant standards. One of them is a Eurocode 3 standard EN 1993-1-6:2007: Design of steel structures Part 1-6: Strength and Stability of Shell Structures. According to this standard, the value of buckling load can be determined using different approaches: classical hand calculations (stress design) and geometrical and material non-linear analysis of an imperfect...
-
Analysis of Cutting Force and Power Under the Conditions of Minimized Cooling in the Process of Turning AISI-1045 Steel with the Use of the Parameter Space Investigation Method
Publikacja -
Analysis of electrochemical parameters in time domain during the passive layer cracking occurring on the 304L stainless steel in chlorides solution under tensile stresses.
PublikacjaDynamiczna Elektrochemiczna Spektroskopia Impedancyjna została wykorzystana do szczegółowej analizy zakresu przejścia stan pasywny - stan aktywny podczas procesu pękania warstwy pasywnej. Wpływ potencjału oraz naprężeń mechanicznych na niszczenie warstwy ochronnej występującej na stali 304L w środowisku 0.5M NaCl w pokojowej temperaturze został przestudiowany. Praca prezentuje chwilowe widma impedancyjne uzyskane przy różnych warunkach...
-
Experimental and analytical thermal study of PTFE composite sliding against high carbon steel as a function of the surface roughness, sliding velocity and applied load
PublikacjaThis study investigates the contact temperatures caused by frictional heating of sliding parallel pairs. In this case the materials studied are a PTFE composite in contact with a high carbon steel plate. These materials are commonly used for industrial applications, in particular as the main contacting components within a scroll expander system. The expected contact temperature values are important to be quantified in order to...
-
High-temperature oxidation of the Crofer 22 H ferritic steel with Mn1.45Co1.45Fe0.1O4 and Mn1.5Co1.5O4 spinel coatings under thermal cycling conditions and its properties
PublikacjaThe aim of the presented study was to deposit protective-conducting Mn1.45Co1.45Fe0.1O4 and Mn1.5Co1.5O4 spinel coatings on the Crofer 22 H ferritic steel by means of electrophoresis and to evaluate their physicochemical properties after high-temperature oxidation under thermal cycling conditions. When the Crofer 22 H steel – whether uncoated or coated with the two spinels – was oxidized in 48-h cycles involving a temperature of...
-
Hybrid analogues of SFTI-1 modified in P1 position by β- and γ-amino acids and N-substituted β-alanines
PublikacjaA series of compounds containing either non-proteinogenic beta-/gamma-amino acids or N-substituted beta-alanine residues (beta-peptoid units) in P-1 specificity position were synthesized based on the structure of sunflower trypsin inhibitor 1 (SFTI-1). The compounds were synthesized on a solid support; the N-substituted beta-alanines (beta Nhlys and beta Nhphe) were introduced into a peptidomimetic chain via a two-step approach...
-
Introduction of Pro and Its Analogues in the Conserved P1 Position of Trypsin Inhibitor SFTI-1 Retains Its Inhibitory Activity
PublikacjaA number of monocyclic SFTI-1 analogues modified in the conserved inhibitor P1 position by Pro, its L-hydroxyproline (Hyp) derivative as well as mimetics with different ring size were synthesized by the solid-phase method. Replacement of Ser6 by Pro, Hyp, and a four-member ring, L-azetidine-2-carboxylic acid (Aze), retained trypsin or chymotrypsin inhibitory activity. The determined association equilibrium constants of these analogues...
-
The Dominant Influence of Plastic Deformation Induced Residual Stress on the Barkhausen Effect Signal in Martensitic Steels
PublikacjaThe paper presents the results of investigation of the influence of plastic deformation on the magnetic properties of martensitic steel (P91 grade). The properties of the hysteresis loops as well as of the Barkhausen effect (BE) signal are analysed for both tensile and compressive loading up to ε = 10% of plastic deformation. The choice of the steel and of the deformation range is unique, since for such combination one can expect...
-
Damage assessment during creep and fatigue of power plant steels using destructive and nondestructive techniques
PublikacjaOpisano wyniki badń mających na celu ocena uszkodzeń od pełzania i zmęczenia stali energetycznych z wykorzystaniem technik niszczących i nieniszczących
-
Shot peening intensity effect on bending fatigue strength of S235, S355 and P460 structural steels
Publikacja -
Influence of cathodic-protection-induced hydrogenation on mechanical properties of two ship hull plate steels
PublikacjaPrzedstawiono wyniki próby rozciągania i udarowej Charpy V dla stali zwykłej wytrzymałości (kategorii A) i podwyższonej wytrzymałości (kat. AH32) zarówno w stanie dostawy jak i po nawodorowaniu (protektor Zn w słonej wodzie). Nawodorowanie obydwu stali zwiększyło nieco granicę plastyczności (Re) i wydłużenie (A), nie zmieniając (atal A) lub nieco zmniejszając przewężenie (Z). Wpływ nawodorowania na udarność był ewidentnie pozytywny...
-
Sulfate‐reducing bacteria‐assisted hydrogen‐induced stress cracking of 2205 duplex stainless steels
PublikacjaThe paper presents the results of a laboratory investigation of the microbiologically assisted hydrogen‐induced stress cracking (HISC) of 2,205 duplex stainless steel (DSS). The testing of susceptibility toward HISC was performed with two different methods. Precharged in sulfate‐reducing bacteria (SRB), inoculated medium samples were subjected to slow strain‐rate testing in artificial seawater. In situ constant load tests were...
-
On the use of the cumulative strain energy density for fatigue life assessment in advanced high-strength steels
PublikacjaIn this paper, the applicability of the cumulative strain energy density is explored as a fatigue indicator parameter for advanced high-strength steels subjected to strain-controlled conditions. Firstly, the cyclic stress-strain responses of nine steels, selected from three multiphase families, encompassing different elemental compositions and different heat treatment routes, were studied. Then, the predictive capabilities of the...
-
Effect of Linear Energy and Microstructure on the Content of Residual Hydrogen in Welded Joints made of Superduplex Steels
PublikacjaThe article presents tests concerning the content of retained hydrogen present in FCAW and SAW welded joints made of superduplex steel. The use of various welding technologies resulted in the obtainment of welds having different microstructures and ferrite contents. Measurements of retained hydrogen present in joints (performed using the complete combustion method) revealed various contents of hydrogen in the base material and...
-
The effect of strain rate on the passive layer cracking of 304L stainless steel in chloride solutions based on the differential analysis of electrochemical parameters obtained by means of DEIS
PublikacjaOkreślono wpływ szybkości rozciągania w zakresie 10-5s-1 ÷ 16∙10-5s-1 na niestacjonarny proces elektrochemiczny pękania warstwy pasywnej. Badania przeprowadzono na stali wysokostopowej 304L w temperaturze pokojowej w środowisku chlorków za pomocą dynamicznej elektrochemicznej spektroskopii impedancyjnej (DEIS). W rezultacie uzyskano zestaw chwilowych widm impedancyjnych odzwierciedlających dynamikę badanego układu korozyjnego....
-
Ocena możliwości zastosowania stali NV2-4 w budowie statków LPG= Estimation of NV2-4 steel implementation possibilities in LPG ships construction
PublikacjaPrzedstawiono wyniki badań złączy spawanych ze stali NV2-4 przeznaczonych na konstrukcje naczyń kriogenicznych w statkach LPG. Wykazano przydatność tej stali na tego typu konstrukcje spawane.
-
Physicochemical properties of Mn1.45Co1.45Cu0.1O4 spinel coating deposited on the Crofer 22 H ferritic steel and exposed to high-temperature oxidation under thermal cycling conditions
PublikacjaThe Crofer 22 H ferritic steel substrate was coated with an Mn1.45Co1.45Cu0.1O4 spinel by means of electrophoresis. After high-temperature oxidation under thermal cycling conditions, the physicochemical properties of the obtained system were evaluated. During 48-h cycles that involved heating the samples up to temperatures of either 750 or 800 °C, the oxidation kinetics of both coated and unmodified steel approximately obeyed...
-
A brief note on monotonic and fatigue fracture events investigation of thin-walled tubular austenitic steel specimens via fracture surface topography analysis (FRASTA)
PublikacjaThe main objective of this short communication is to show the fracture progression in each loading case and complement knowledge about fracture mechanisms underpinning the tensile and fatigue performance of thin-walled tubes. For this purpose, the fracture surface topography analysis (FRASTA) method was used in the thin-walled tubular austenitic stainless-steel specimens. Two cases were analyzed: monotonic tension, and uniaxial...
-
Development of fragility curves in adjacent steel moment-resisting frames considering pounding effects through improved wavelet-based refined damage-sensitive feature
PublikacjaFragility curves present useful information related to earthquake-induced probability assessment of steel moment-resisting frames (MRFs) and determine the probability of the damage exceedance at different floor levels of MRFs. The review of the literature shows that most of the previous studies dealing with the fragility curves were based on conventional measures, such as spectral acceleration at the first mode period, peak...
-
Mechanical and fracture properties of concrete reinforced with recycled and industrial steel fibers using Digital Image Correlation technique and X-ray micro computed tomography
PublikacjaPaper presents investigation of fracture phenomenon in plain concrete and in concrete reinforced with both recycled steel fibers (RSF) and industrial steel fibers (ISF). The wedge splitting test (WST), which enables stable crack propagation for quasi-brittle materials, was carried out on 75 75 75 mm cube samples. Initially, fracture process zone development was investigated only on the surface of samples using Digital Image Correlation...
-
EH36 steel for shipbuilding (plate thicnkness 30 mm) - 3D fracture scan
Dane BadawczeThe basic method of ductility designation of structural steels is the Charpy impact test. The test consists of a single strike of the specimen using a Charpy pendulum. Its result is the value of work necessary to break a specimen at a test temperature. Despite its many advantages, such as its short implementation time and low costs, it has its disadvantages,...
-
SEM examination of surface layer of C45 steel after grinding on defferent depth
Dane BadawczeFerrite examination for the medium carbon structural steel with low content of Mn, Si, Cu, Cr and Ni after its grinding to a depth of 2 µm, 8 µm, 14 µm and 20 µm, at constant wheel circumferential speed of vs = 25 m/s and constant feed rate vft = 1 m/min. It was shown that the grinding of C45 steel causes strong work hardening of ferrite in surface...
-
Complex Steel Structures 2022
Kursy Online -
Mateusz Kopec Dr hab. inż.
OsobyHead of the Materials and Structural Testing Laboratory in Institute of Fundamental Technological Research PAS and Academic visitor in Imperial College London. Lecturer and Master/PhD students supervisor in Doctoral School of IPPT PAN and TIB PAN, and Imperial College London. Member of Polish Materials Science Society, Member of the Board of Polish Society of Theoretical and Applied Mechanics, and Council Member of the European...
-
Hydrogen permeation through welded joints of S690QL steels at cathodic polarisation in sea water in the presence of SRB
PublikacjaPrezentowane są wyniki badan metodą Devanathana- Stachurskyego przenikania wodoru w wodzie morskiej w obecności bakterii redukujących siarczany i w warunkach sterylnych. Badania wykonano na stali S690QL poddanej symulowanym obróbkom cieplnym prowadzącym do struktur modelujących strefy wpływu ciepła. Stwierdzono dodatni wpływ obecności bakterii na przenikanie wodoru. Różnice między poszczególnymi próbkami były minimalne.
-
The impact of surface slope and calculation resolution on the fractal dimension for fractures of steels after bending-torsion fatigue
PublikacjaThe article presents the results of the fractal dimension measurements on the fatigue fracture surfaces of 10HNAP and S355J2 steels specimens after combined bending-torsion fatigue. For smooth and ring-notched specimens, three loading conditions were analyzed: (1) bending; (2) bending-torsion; and (3) torsion fatigue. Post-failure surface topography measurements were carried out on the entire fracture surfaces using an optical...
-
Susceptibility of Cr-Ni-Mn steel to the hydrogen degradation in boiler fuel = Podatnośc stali Cr-Mn-Ni na niszczenie wodorowe w paliwie kotłowym
PublikacjaStal 34HNM poddana różnym obróbkom cieplnym wykazała skłonność do korozji naprężeniowej w pomiarach ze stałą niską szybkością rozciągania i do zmęczenia korozyjnego niskocyklowego. Mechanizmem zniszczenia była degradacja wodorowa. Możliwe źródła pochłaniania wodoru to: korozja, degradacja węglowodorów z tworzeniem się kwasów organicznych i promotorów wnikania wodoru.
-
Stalowe panele sandwicz - nowe możliwości wynikające z zastosowania spawania laserowego = All steel sandwich panels - new possibilities introduced by laser welding techniques
PublikacjaW artykule przedstawiono podstawowe dane na temat stalowych paneli typu sandwicz i technik ich wykonywania. Złącze takie charakteryzuje się specyficznymi własnościami, zdecydowanie odmiennymi od klasycznego połączenia spoiną pachwinową, którego cechy wytrzymałościowe i technologiczne są już dobrze opanowane. W podsumowaniu wykazano, że modelowanie jego geometrii musi być prowadzone na znacznie większym poziomie szczegółowości ze...
-
Ocena możliwości pozostawienia żurawia 642-24 na estakadzie B-5 (PK3, 291-46) w obecnej lokalizacji tj. od strony ul. Jana z Kolna po modyfikacji schematu statycznego
PublikacjaEkspertyza dotyczy oceny możliwości pozostawienia żurawia 642-24 na estakadzie B-5 (PK3, 291-46) w obecnej lokalizacji tj. od strony ul. Jana z Kolna po modyfikacji schematu statycznego. Zakres opracowania obejmuje opisy: aktualnego stanu technicznego obiektu, badań polowych, obliczeń i analiz MES konstrukcji oraz orzeczenie dotyczące warunków realizacji modernizacji estakady.
-
Imaging of morphological and physicochemical changes occuring in the structure of austenitic steel due to the thermal sensitization
Dane BadawczeIn polycrystalline materials, grain boundaries are always where phenomena such as surface diffusion, sedimentation and corrosion occur. They have a significant impact on the macroscopic properties of the construction material [1]. In addition to inhomogeneities such as manganese sulphide inclusions formed during the metallurgical process, interfacial...
-
A New Adaptive Method for the Extraction of Steel Design Structures from an Integrated Point Cloud
Dane BadawczeA new automatic and adaptive algorithm for edge extraction from a random point cloud was developed and presented herein. The proposed algorithm was tested using real measurement data. The developed algorithm is able to realistically reduce the amount of redundant data and correctly extract stable edges representing the geometric structures of a studied...
-
The corrosion studies of 3,4,5-trihydroxybenzoic acid as an effective corrosion inhibitor of low alloy steel
Dane BadawczeThe dataset contains the electrochemical studies evaluating if gallic acid is a corrosion inhibitor for low alloy steel. Three measurements were carried out each case; corrosion potential (label ecorr), electrochemical impedance spectroscopy (label eis) and cyclic polarization (label cp). The measurements were carried out in sodium chloride, acidified...
-
Analogues of trypsin inhibitor SFTI-1 modified in the conserved P1′ position by synthetic or non-proteinogenic amino acids retain their inhibitory activity
PublikacjaA series of linear and monocyclic (with a disulfide bridge only) analogues of trypsin inhibitor SFTI-1 modified in the P-1 and/or P-1' positions were synthesized by the solid-phase method. In the substrate specificity P-1 position, Phe or N-benzylglycine (Nphe) were introduced, whereas the conserved Ser6 in Bownam-Birk (BBI) inhibitors was replaced by Hse (L-homoserine), Nhse [N-(2-hydroxyethyl)glycine], Sar, and Ala. Kinetic studies...
-
Does abdominal obesity have a similar impact on cardiovascular disease and diabetes? A study of 91 246 ambulant patients in 27 European Countries
Publikacja -
Badania jakości docierania stali hartowanej docierakami aktywizowanymi w sposób swobodny = Study of hardened steel lapping quality where lapping tools are activized in a free way
PublikacjaPrzedstawiono badania jakości docierania stali hartowanej docierakami zbrojonymi w sposób swobodny. Analizowano wpływ podstawowych warunków obróbki na chropowatość powierzchni obrobionej. Wyznaczono zależność parametru Ra od prędkości i czasu docierania oraz nacisku jednostkowego. Analizowano również zanieczyszczenie powierzchni ścierniwem po docieraniu.