wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: SCREW CONFIGURATION
-
Data set generation at novel test-rig for validation of numerical models for modeling granular flows
PublikacjaSignificant effort has been exerted on developing fast and reliable numerical models for modeling particulate flow; this is challenging owing to the complexity of such flows. To achieve this, reliable and high-quality experimental data are required for model development and validation. This study presents the design of a novel test-rig that allows the visualization and measurement of particle flow patterns during the collision...
-
Single-phase, Five-level Inverter with SPWM-Based Neutral Point Voltage Balancing Scheme
PublikacjaMultilevel inverter topologies provide several advantages over two-level inverter configuration. These benefits are the reason for the growing interest in multilevel topologies among research society. One of the most popular topological concepts (diode and active switch clamping) requires neutral-point potential balancing due to series-connected capacitor banks across the input dc link in such derived inverter configurations. This...
-
The Application of Fluidic Sealing in Shrouded Gas Turbine Blades
PublikacjaThis paper presents a study conducted on a new gas turbine designed to limit leakage in the labyrinth seal. The slots in the fin are used to generate a bypass flow, which obstructs the flow in the gap above the fin. The method was tested numerically and experimentally beforehand using a simplified model without rotation or blade passages. In this paper, the validation of the method using a model of a turbine stage is shown. Reynolds-averaged...
-
Low Cost Hexacopter Autonomous Platform for Testing and Developing Photogrammetry Technologies and Intelligent Navigation Systems
PublikacjaLow-cost solutions for autonomous aerial platforms are being intensively developed and used within geodetic community. Unmanned aerial vehicles are becoming very popular and widely used for photogrammetry and remote sensing applications. Today’s market offers an affordable price components for unmanned solution with significant quality and accuracy growth. Every year market offers a new solutions for autonomous platforms with better...
-
Miniaturized Inline Bandpass Filters Based on Triple-Mode Integrated Coaxial-Waveguide Resonators
PublikacjaThis work presents a design technique to implement miniaturized cross-coupled bandpass filters in inline physical configurations based on triple-mode resonators. Triple-mode resonances are obtained by using integrated coaxial-waveguide cavity resonators. They consist of two coaxial conducting posts placed in the sidewalls of a rectangular waveguide cavity. In the proposed triplet, a transmission zero (TZ) can be positioned at any...
-
Bezzałogowe środki latające (BSL) w układzie czterowirnikowego helikoptera
PublikacjaRozwój układów sterowania, kamer pracujących w świetle widzialnym oraz w podczerwieni doprowadził do wzrostu znaczenia bezpilotowych środków latających. Bezpilotowe środki latające wykorzystywane są do realizacji celów zarówno wojskowych, jak i cywilnych. Podstawowymi zaletami bezpilotowych środków latających są: małe wymiary, duża mobilność, niskie koszty wytworzenia i eksploatacji. Użytkowanie bezpilotowych środków latających...
-
Analysis of IPv6 handovers in IEEE 802.16 environment
PublikacjaThe second generation of WiMAX solutions, based on IEEE 802.16-2005 standard, offers limited mobility support. Unfortunately, after quickly changing the point of attachment on the WiMAX data link layer (DLL), very slow and inefficient IPv6 reconfiguration takes place. Delays introduced by automatic configuration (DHCPv6 and IPv6 protocols) and Mobile IPv6 can easily diminish or even render useless all benefits gained using the...
-
Remote Stateful Autoconfiguration for Mobile IPv6 Nodes with Server Side Duplicate Address Detection
PublikacjaDuring interdomain handover, IPv6 node requires new address at its new location. Once the L2 handover procedure is completed, mobile node (MN) starts its IPv6 configuration, using stateless (router advertisements) or stateful (DHCPv6 communication) mode. Once the address is obtained, its uniqueness has to be verified, using Duplicate Address Detection (DAD) procedure. Depending on the interface type, this procedure may easily take...
-
Thermo-mechanical reclaiming of ground tire rubber via extrusion at low temperature: Efficiency and limits
PublikacjaThermomechanical reclaiming of ground tire rubber (GTR) was performed at different temperatures (60, 120, and 180°C) using a co-rotating twin-screw extruder. Obtained samples were used in styrene-butadiene rubber (SBR) blends. As reference samples, SBR compounds containing untreated GTR were used. Curing characteristics, static and dynamic mechanical properties, and morphology of the obtained blends were determined. The results...
-
Leszek Ziemczonek dr
OsobyUniversity education 1973-1978 – Nicolaus Copernicus University in Toruń, University of Gdańsk in Gdańsk, Mathematical Physics, M. Sc. 1979 – Diploma of Postgraduate Studies, Pedagogics 1989 – Institute of Physics, Polish Academy of Sciences in Warsaw, Theoretical Physics, Ph. D. 2010-2012 – Diploma of Postgraduate Studies, Mathematics Training: · 09.1983 – Trieste (Italy) – International Centre for Theoretical Physics...
-
Evaluating Security and Resilience of Critical Networked Infrastructures after Stuxnet
PublikacjaThe chapter presents the current configuration of the simulation environment for the evaluations of the security and resilience of critical networked infrastructures, which enables simulations of Stuxnet-like attacks. The configuration includes new features added to the MAlSim - Mobile Agent Malware Simulator after the advent of Stuxnet in reference to the experiments aiming at the security evaluation of a power plant which we...
-
Minichannel and minigap classification criteria based on the aspect ratio of the minigeometry: A numerical study
PublikacjaA detailed numerical investigation has been carried out to analyze the diabatic flow distribution and velocity profile in 18 minigeometries with various aspect ratios for V-type and I-type flow configurations (for 36 cases) assuming ethanol as a working fluid. The aim of the study is to distinguish the value of the aspect ratio for which the flow in minigeometry starts to be two-dimensional (minigap). Cases with a constant Reynolds...
-
A Developer's View of Application Servers Interoperability
PublikacjaThe paper describes analysis of application servers interoperability that considers both the available level of integration and the required level of development complexity. Development complexity ranges from simple GUI operations to changes of undocumented features in configuration files. We verify if an integration can be established on a given level of development complexity, rather than verify if it is objectively feasible....
-
Direction-of-Arrival Estimation Methods in Interferometric Echo Sounding
PublikacjaNowadays, there are two leading sea sounding technologies: the multibeam echo sounder and the multiphase echo sounder (also known as phase-dierence side scan sonar or bathymetric side scan sonar). Both solutions have their advantages and disadvantages, and they can be perceived as complementary to each other. The article reviews the development of interferometric echo sounding array configurations and the various methods applied...
-
The structure, including stereochemistry, of levorin A1
PublikacjaThe constitution and stereostructure of levorin A1 1, an aromatic heptaeneantifungal antibiotic, was established on the basis of NMR studies, which contained DQFCOSY,ROESY, HSQC and HMBC experiments. Mycosamine moiety was used as an internalchiral probe to determine the absolute configuration of levorin A1 stereogenic centers: 13S,15R, 17S, 18R, 19S, 21R. The relative configuration of the remaining stereogenic centers wasassigned...
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 009_v_2
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 009_v_3
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 009_h_3
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 019_v_5
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 009_h_5
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 009_h_4
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 039_h_4
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 019_v_4
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 019_h_5
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 039_v_4
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 009_v_4
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 039_v_3
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 019_v_3
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 019_h_3
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 039_h_5
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 019_h_4
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 039_v_2
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 039_h_3
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
Modeling of Performance, Reliability and Energy Efficiency in Large-Scale Computational Environments
PublikacjaLarge scale of complexity of distributed computational systems imposes special challenges for prediction of quality in such systems. Existing quality models for lower-scale systems include functionality, performance, reliability, flexibility and usability. Among these attributes, performance and reliability have a particular significance to the large-scale systems computing quality modeling due to their strong dependence on the...
-
Adapting a General Tool to Monitoring Multi-Agent Systems Through Virtual Host Layer Extenstion
PublikacjaNagios is a free software for IT infrastructure monitoring. Out-of-the-box it is not suited for monitoring multi-agent systems, because agents may dynamically join and leave the system or change roles. But Nagios' flexible configuration makes extensions possible. This paper presents and verifies Nagios configuration and extensions for monitoring multi-agent systems.
-
Comparative model tests of SDP and CFA pile groups in non-cohesive soil
PublikacjaThe research topic relates to the subject of deep foundations supported on continuous flight auger (CFA) piles and screw displacement piles (SDP). The authors have decided to conduct model tests of foundations supported on the group of piles mentioned above and also the tests of the same piles working alone. The tests are ongoing in Geotechnical Laboratory of Gdańsk University of Technology. The description of test procedure, interpretation...
-
Use of response surface methodology in characterization of properties of recycled high density polyethylene/ground tire rubber compositions
PublikacjaSearching for newways to utilize rubber and polymerwaste has been the focus of many studies conducted by research centers and companies worldwide. In this study, the influence of extrusion conditions on the properties of thermoplastic compositions containing post-production recycled high density polyethylene (PE-HD) and ground tire rubber (GTR) at 50:50 mass ratiowas examined. Response Surface Methodology (RSM) was used to determine...
-
Processing data on sea bottom structure obtained by means of the parametric sounding
PublikacjaThe aim of the paper is to analyze data obtain during sounding of the Gdansk Bay by means of the parametric sonar. The accuracy of the sea bottom structure investigation needs the correct configuration of research equipment and the proper calibration of peripheral devices (GPS, heading sensor, motion sensor MRU-Z and navigation units) which provide necessary data to bathymetrical measurement system enabling its work with whole...
-
The concept of sewage-sludge management system for an individual household
PublikacjaThe individual farms at the rural areas often face problems with domestic sewage collection and treatment. In many cases building of sewerage systems and central wastewater treatment plants (WWTPs) brings too high costs, due to high distances from one farm to another and terrain configuration. Treatment wetlands for individual farms can solve this problem. In the article, an overview of individual treatment wetlands in Europe and...
-
Processing data on sea bottom structure obtained by means of the parametric sounding
PublikacjaThe aim of the paper is to analyze data obtained during sounding the Gdansk Bay sea bed by means of the parametric echo-sounder. The accuracy of the sea bottom structure investigation needs correct configuration of research equipment and proper calibration of peripheral devices (GPS, heading sensor, MRU-Z motion sensor and navigation instruments which provide necessary data to bathymetrical measurement system, enabling its work...
-
Interoperability Description of Web Services Based Application Servers
PublikacjaWeb services standards were designed to enable interoperability of heterogeneous application servers in the Service Oriented Architecture. Although the standards proved to be highly successful, there are still difficulties in effective services integration. The paper presents a methodology that enables description of application servers interoperability in order to improve the service integration process. The methodology proposes...
-
Comparative analysis of three‐phase dual active bridge converter with different transformer topology and modern universal control for DC microgrids
PublikacjaThe presented work discusses issues related to the use of modern multiphase topologies of Dual Active Bridge (DAB)-type converters. Converters of this type are widely used in most DC microgrid applications. The introduction emphasizes a comparative analysis between single-phase and multi-phase DAB topologies within high-power DC microgrids, delving into their respective advantages, drawbacks, design procedures, and considerations...
-
Opracowanie procedury i badania wytrzymałościowe połączeń spawanych pomiędzy rurą kwadratowa a elementami giętymi na zimno ze stali S355 oraz testowanie połączeń o grubości 4, 6, 8mm typu S355
PublikacjaCelem pracy było: - opracowanie procedury badania wytrzymałości połączeń spawanych rozciąganych w kierunku prostopadłym i w kierunku równoległym (ścinanych) do osi spoiny. Spoiny te łączyły elementy rur kwadratowych o różnej grubości z elementami w kształcie ceownika giętymi na zimno. - wykonanie próbek do badań wytrzymałościowych wyciętych z elementów spawanych dostarczonych przez Zakład Produkcyjny firmy Borga obciążonych prostopadle...
-
Analysis of IPv6 Handovers in IEEE 802.16 environment
PublikacjaZaprezentowano pełną analizę wpływu poszczególnych faz procesu przełączania w warstwie drugiej i trzeciej na przerwy w transmisji wynikające ze zmiany stacji bazowej BS przez przemieszczający się węzeł ruchomy MN. Zaproponowano i przebadano symulacyjnie 10 scenariuszy przełączania, w tym 8 różnych algorytmów stanowej autokonfiguracji węzłów MN, wspierających protokół IPv6 w środowiskach sieci WiMAX. W badaniach wskazano na możliwości...
-
Combined cold supply system for ship application based on low GWP refrigerants - Thermo-economic and ecological analyses
PublikacjaThe withdrawal of popular high-GWP refrigerants will significantly affect maritime industry. Refrigeration and air conditioning systems currently used on ships are not ready to fulfil future limitations. Therefore, there is a need for system, which will operate with low-GWP refrigerants and at the same time will be efficient and reliable in difficult environmental conditions. This paper explains the concept of a cold supply system,...
-
Design of Frequency-Reconfigurable Branch-Line Crossover Using Rectangular Dielectric Channels
PublikacjaThis paper presents an efficient yet straightforward passive reconfiguration technique to tune the operating frequency of a branch-line crossover (BLCO). The underlying principle is to fill rectangular dielectric channels (RDCs) prepared beforehand with either air or materials of different relative permittivity. Two configurations (one RDC and three RDCs in each arm) of the branch-line crossover are employed to estimate the tunability...
-
Importance of model tests in design and operation of watercraft for example CTO
PublikacjaShip Hydromechanics Division is a specialized research and development department of Ship Design and Research Centre conducting tests and research in the field of hydromechanics, connected with design and operation of ships and other floating structures, in scope of: predictions, numerical analyses, designs of - hull shape optimized with respect to the ship’s functions with the application of modern design tools, screw propellers...
-
Wpływ polietylenu szczepionego bezwodnikiem maleinowym oraz sił ścinających na właściwości mieszanin polietylen wysokiej gęstości-miał gumowy
PublikacjaScharakteryzowano wpływ kompatybilizatora w postaci polietylenu szczepionego bezwodnikiem maleinowym na właściwości mieszanin PE-HD–miał gumowy. Kompozycje termoplastyczne zawierające 50 cz. mas. rozdrobnionych odpadów gumowych, otrzymano przy użyciu współbieżnej wytłaczarki dwuślimakowej. Poziom sił ścinających generowanych podczas mieszania, regulowano za pomocą zmian prędkości obrotowych ślimaków. Przeprowadzono charakterystykę...
-
Chiral analysis of chloro intermediates of methylamphetamine by one-dimensional and multidementional NMR and GC/MS
PublikacjaImpurity profiling and classification of abused drugs using chiral analytical techniques is of particular interest and importance because of the additional information obtained fromthis approach. When these methods are applied to the synthesis of illicitly used substances, they can supply valuable information about the conditions/chemicals used in the synthesis. We have applied GC and NMR methods to the study of intermediates found...
-
On Configurability of Distributed Volunteer-Based Computing in the Comcute System
PublikacjaThe chapter proposes additional solutions that can be implemented within the Comcute system to increase its configurability. This refers to configuration of the reliability level in the W and S server layers, static or on-the-fly data partitioning and integration, configuration of the system for processing in the data streaming fashion, extending the system for selection of a project that the client wants to contribute to, ease...