wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: DIAMETER, RSVP
-
Wpływ procesu redukcji na właściwości strukturalne i mechaniczne szkieł tlenkowych z grupy (Pb,Bi)-(Si,Ge)-O = Influence of reduction process on the structural and mechanical properties of (Pb,Bi)-(Si,Ge)-O oxide glasses
PublikacjaThe effect of the reduction process in H2 at 380 °C on the microstructure and elemental composition of a glass Bi0.4Pb0.2Si0.4Ox has been investigated. It has been shown that after reduction a clearly separated top layer with a thickness of approx. 50 µm was formed on the surface of the sample. This layer is depleted of oxygen and has higher electrical conductivity than the interior of the glass. It has also been found that some...
-
Optimization of Self-Organized TiO2 Nanotube Geometry on Ti and Ti Alloys Using Fuzzy Logic Reasoning
PublikacjaThe geometry of self-organized TiO2 nanotubes, obtained by electrochemicalanodization, has been determined by using fuzzy reasoning approach. The efficiency of TiO2nanotubular layer in biomedical applications depends on geometry and available surface area ofnanotubes, which can be determined by their diameter and length. The structure of nanotubesdepends on processing parameters of electrochemical anodization, like applied potential,anodization...
-
Experimental investigations on pressure drop during the condensation in flow of HFE7000 in vertical minichannel
PublikacjaIn the work presented in the paper authors focused attention on the issues of flow resistance and pressure drop during condensation in the flow. The case of the descending flow through a cylindrical single-channel of 2.3 mm inner diameter was carefully analyzed. In the course of investigations a new working fluid HFE 7000 has been scrutinised which has a strongly differing properties in comparison to the other fluids that are commonly...
-
Experimental study of the post tensioned prestressed concrete corbels
PublikacjaThe results of experimental investigation of 6 symmetrical double prestressed corbels of variable shear span to depth ratio and variable location of prestressing bars are presented in the paper. The post ten- sioned corbels were prestressed with Macalloy 1030 bars of 25 mm in diameter. The results of the tests were compared with the cracking and load carrying capacity of corbels reinforced with passive reinforce- ment. As a result...
-
Mechanical characterization of a gravel column in a calibration chamber operating as a triaxial cell
PublikacjaA series of tests considering the behavior of gravel columns was performed. A segment of column with a height of 1 m and a diameter of 0.53 m was modelled in a calibration chamber used as a triaxial cell at three different lateral stress applied. The vertical load transferred on the column head was simulated with steady increase of water pressures in the upper and lower membranes. During the loading the volumetric changes in the...
-
Abdominal Aortic Aneurysm segmentation from contrast-enhanced computed tomography angiography using deep convolutional networks
PublikacjaOne of the most common imaging methods for diagnosing an abdominal aortic aneurysm, and an endoleak detection is computed tomography angiography. In this paper, we address the problem of aorta and thrombus semantic segmentation, what is a mandatory step to estimate aortic aneurysm diameter. Three end-to-end convolutional neural networks were trained and evaluated. Finally, we proposed an ensemble of deep neural networks with underlying...
-
Leydig cell tumor of ovary, NOS - Female, 50 - Tissue image [3300730005953701]
Dane BadawczeThis is the histopathological image of OVARY tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.
-
Dieter Scharnweber
Osoby -
Facile formation of self-organized TiO2 nanotubes in electrolyte containing ionic liquid - ethylammonium nitrate and their remarkable photocatalytic properties
PublikacjaThe oriented TiO2 nanotube arrays (NTs) are identified as a stable, active and recyclable photocatalytic surface. However, their photoactivity is strictly depended on morphology (especially length), which could be controlled by anodic oxidation parameters, including electrolyte properties. To control the morphology, were successfully synthesized a series of NTs by a novel approach where ionic liquid (IL), ethylammonium nitrate...
-
Problems with modelling the strength properties of sailing vessels rigging ropes
PublikacjaThis article presents the basic parameters of soft ropes: natural fibre ropes, soft wire ropes and synthetic fibre ropes used for running rigging. There are only several materials still used for the production of natural fibre ropes, including cotton, jute, hemp, sisal and manila hemp. The most commonly used soft wire ropes are twisted pair ropes; for smaller diameters there is a 6x19M - FC rope and for larger diameters – 6x37M...
-
Shaping of the workpiece surface in single-disc lapping
PublikacjaShape errors of the tool exert a dominant influence on the shape accuracy of the workpiece. The correlation between flatness errors of the lap and flatness errors of the workpieces was checked experimentally and determined analytically. Computer model of the workpiece shaping by lapping was developed. Evaluation method of the workpiece orientation as well as some simulation results for a lap with shape errors of convexity and cincavity...
-
Global 30-day outcomes after bariatric surgery during the COVID-19 pandemic (GENEVA): an international cohort study
Publikacja -
Application in circular sawing machines of the experimental results of investigations of the chip removing system operation
PublikacjaThe experimental results of the chip removing system operation are presented. The main aim of them was to optimize suction system of the panel saw Fx3 and its follower Fx550. The attention was focused on the upper casing, which was the part of removing system. Within the framework of the work a systematic experimental study of pressure distribution in the casing during operation of the selected rotational speed of saw blade with...
-
Effect of the inclination angle of the condenser on the heat transfer coefficient value – experimental study
PublikacjaWhen considering problem of the condensation of the refrigerant in a flow inside channel, one needs to pay attention to the shape of its cross-section, the hydraulic diameter, the channel length as well as the orientation of the channel axis in space (horizontal, vertical, inclined). This paper presents an experimental study concerning the effect of the inclination angle of the condenser with a single coil pipe on the heat transfer...
-
Study of the atomic structure and morphology of the Pt3Co nanocatalyst
PublikacjaThe local structure and chemical disorder of a commercially available Pt3Co nanocatalyst supported on high surface area carbon were investigated. High-quality XAFS spectra were collected at the ELETTRA synchrotron XAFS 11.1 beamline. XAFS spectra analysis have been performed accounting for the reduction of the coordination number and degeneracy of three-body configurations, resulting from transmission electron microscopy (TEM)...
-
Thermal Analysis Of Hybrid Microchannel-Microjet Heat Exchanger
PublikacjaThe paper presents the numerical investigation of a microjet- microchannel cooling module. In which microjets of water are impinging into the microchannels and forming a liquid film on the impingement surface. Applied technology takes benefits from two very attractive heat removal techniques. When laminar jets are impinging on the surface have a very high kinetic energy at the stagnation point, also in microchannels boundary layer...
-
Development and application of asphalt binder relaxation test in different dynamic shear rheometers
PublikacjaIn this study, a novel relaxation test is proposed to evaluate asphalt binder low temperature properties using a Dynamic Shear Rheometer (DSR) with parallel plates of 4 mm in diameter. Three rheometers from three different manufacturers are used to analyze seven asphalt binders. Different material parameters are derived which are useful to evaluate and discriminate different asphalt binders. Test results of all three instruments...
-
Peculiarities of measurement uncertainty evaluation at calibrating a ring gauge
PublikacjaExample S13 from EA-4/02 M:2013 “Calibration of a ring gauge with a nominal diameter of 90 mm” is analyzed. The report uses the kurtosis method and the law of propagation of expanded uncertainty developed by the authors to the expanded uncertainty evaluation. It is shown that the introduction of a coaxiality correction for the ring gauge and the measuring axis of the comparator leads to the need to estimate its standard measurement...
-
Attenuation of Hyperglycemia in Diabetic Rats Assisted by Immobilized Probiotic in Sodium Alginate
PublikacjaDiabetes mellitus type 2 (DM2) is the most common chronic disease worldwide, characterized mainly by increased glucose concentration in the blood and affecting several organs’ functionality. The daily consumption of probiotic bacteria can help control diabetes and reduce the damage caused. Cell immobilization techniques are a powerful tool that provides physical cell protection to such probiotic bacteria against gastrointestinal...
-
Artificial Neural Network based fatigue life assessment of riveted joints in AA2024 aluminum alloy plates and optimization of riveted joints parameters
PublikacjaThe objective of this paper is to provide the fatigue life of riveted joints in AA2024 aluminum alloy plates and optimization of riveted joints parameters. At first, the fatigue life of the riveted joints in AA2024 aluminum alloy plates is obtained by experimental tests. Then, an artificial neural network is applied to estimate the fatigue life of riveted lap joints based on the number of lateral and longitudinal holes, punch pressure,...
-
Mobility Managment Scenarios for IPv6 Networks-Proxy Mobile IP-v6Implementation Issues
PublikacjaManagement of user at the network layer plays an important role in efficient network operation. In the paper, authors' implementation of one of network-based mobility management models, namely Proxy Mobile IPv6, is presented and tested in a number of networking topologies and communication scenarios. The proposed implementation covers PMPIv6 functionality with optional security extensions (use of Diameter protocol) and handover...
-
Imaging of Increasing Damage in Steel Plates Using Lamb Waves and Ultrasound Computed Tomography
PublikacjaThis paper concerns inspection of steel plates, with particular emphasis on the assessment of in-creasing damage. Non-destructive tests were performed on four plates, one of which was un-damaged, while the remaining three had a defects in the form of circular holes with a diameter of 2, 5, and 10 cm. Guided Lamb waves were used in the research, and the image reconstruction was performed using ultrasound computed tomography. The...
-
Free Vibration of Flexomagnetic Nanostructured Tubes Based on Stress-driven Nonlocal Elasticity
PublikacjaA framework for the flexomagneticity influence is here considered extending the studies about this aspect on the small scale actuators. The developed model accommodates and composes linear Lagrangian strains, Euler-Bernoulli beam approach as well as an extended case of Hamilton’s principle. The nanostructured tube should subsume and incorporate size effect; however, for the sake of avoiding the staggering costs of experiments,...
-
Uncertainty of mass flow measurement using centric and eccentric orifice for Reynolds number in the range 10,000 ≤ Re ≤ 20,000
PublikacjaThe article analyses the impact of the Reynolds number on the estimated uncertainty of the mass flow rate measurement using an orifice plate. The objects of the research were two types of orifices: centric (ISA) and eccentric, with the diameter ratio β = 0.5. Studies were performed by Monte Carlo simulation and experiments for Reynolds numbers in the range 10,000 ≤ Re ≤ 20,000. The obtained results have shown that for both orifice...
-
Experimental Investigation of the Thermal Performance of a Wickless Heat Pipe Operating with Different Fluids: Water, Ethanol, and SES36. Analysis of Influences of Instability Processes at Working Operation Parameters
PublikacjaIn this study, the influences of different parameters on performance of a wickless heat pipe have been presented. Experiments have been carried out for an input power range from 50 W to 300 W, constant cooling water mass flow rate of 0.01 kg/s, and constant temperature at the inlet to condenser of 10 C. Three working fluids have been tested: water, ethanol, and SES36 (1,1,1,3,3-Pentafluorobutane) with different filling ratios (0.32,...
-
The importance of individual spray properties in performance improvement of a urea-SCR system employing flash-boiling injection
PublikacjaThe appropriate mixing of a urea–water solution (UWS) with exhaust gases in a selective catalytic reduction system is crucial to efficiently reduce nitrogen oxides and diminish the deposition of liquid wall film. One of the methods to enhance the mixing of the UWS with the exhaust gases is a flash-boiling injection. Its positive effect has been linked with a reduced Sauter mean diameter (SMD) and improved evaporation, but the...
-
Cytocompatibility, antibacterial, and corrosion properties of chitosan/polymethacrylates and chitosan/poly(4‐vinylpyridine) smart coatings, electrophoretically deposited on nanosilver‐decorated titania nanotubes
PublikacjaThe development of novel implants subjected to surface modification to achieve high osteointegration properties at simultaneous antimicrobial activity is a highly current problem. This study involved different surface treatments of titanium surface, mainly by electrochemical oxidation to produce a nanotubular oxide layer (TNTs), a subsequent electrochemical reduction of silver nitrate and decoration of a nanotubular surface with...
-
Investigation of RH effect on uncommon limonene ozonolysis products and SOA formation in indoor air with real time measurement techniques
PublikacjaScientific interest in SOA influence on indoor air quality increases since last 20 years. It is well known, that particles of nano-sized diameter pose a threat for human health causing, among others: eye, upper airway irritation, inflammatory response in cells, worsening asthma, hypertension, diabetes, and central nervous dysfunction. Terpenes are reactive VOCs, commonly emitted in indoor air and considered to be SOA precursors...
-
On Computing Curlicues Generated by Circle Homeomorphisms
PublikacjaThe dataset entitled Computing dynamical curlicues contains values of consecutive points on a curlicue generated, respectively, by rotation on the circle by different angles, the Arnold circle map (with various parameter values) and an exemplary sequence as well as corresponding diameters and Birkhoff averages of these curves. We additionally provide source codes of the Matlab programs which can be used to generate and plot the...
-
Bezpieczeństwo w IP Multimedia Subsystem
PublikacjaAbstrakt Artykuł jest trzecim w cyklu prac poświęconych IP Multimedia Subsystem (IMS) - po przedstawieniu architektury i usług IMS, odpowiednio w zeszytach 12/2009 oraz 2-3/2011 Przeglądu Telekomunikacyjnego i Wiadomości Telekomunikacyjnych. W obecnym artykule przedstawiono sposoby zapewnienia bezpieczeństwa przy realizacji tych usług.Artykuł został podzielony został na trzy części w których omówiono ogólne wyzwania bezpieczeństwa...
-
Optimization of chip removing system operation in circular sawing machine
PublikacjaThe paper presents the optimization of the wood chips removing system in the sliding table saw. Chips are generated during the cutting of the material. The attention was focused on the upper casing of mentioned system. The methodical experimental studies of the pressure distribution inside the casing during the wood chip removing operation for the selected rotational speed of saw blade with a diameter of 300 mm and 450 mm were...
-
Mechanical Properties of Aluminium Bracket Strengthening
PublikacjaThe aim of the research is laboratory investigation of aluminium brackets employed to fasten lightweight curtain walls to building facilities. Tensile loads perpendicular to end plates (vertical) were applied here. The author focused on the solutions intended to increase the load-carrying capacity of aluminium brackets applying the plain washer form A (DIN 125; ISO 7089), plain washer with an outer diameter about 3d (DIN 9021;...
-
THE USE OF FEM FOR DETERMINATION OF RESONANT FREQUENCIES OF CIRCULAR SAW BLADES WITH INDIRECT TEETH IN GULLETS
PublikacjaUnderstanding the dynamical properties of the circular saw blade is necessary, since, there is a really need for a stable work at working rotational speeds, which are determined by frequencies at which the circular saw blade tends to vibrate. It was observed that the resonant frequency depend on the circular saw blade shape, a collar diameter and on saw’s teeth shape. In the presented work an attention was paid to the effect of...
-
THERMAL ANALYSIS AND DESIGN OF HYBRID MICROCHANNEL-MICROJET TEST PROBE
PublikacjaThe paper presents the numerical investigation of a microjet- microchannel cooling module. In which microjets of water are impinging into the microchannels and forming a liquid film on the impingement surface. Applied technology takes benefits from two very attractive heat removal techniques. When lminar jets are impinging on the surface have a very high kinetic energy at the stagnation point, also in microchannels boundary layer...
-
Heat Transfer During Pool Boiling of Water, Methanol and R141b on Porous Coated Horizontal Tube Bundles
PublikacjaThis paper presents the results of experimental investigation of water, methanol and R141b refrigerant boiling on horizontal porous coated tube bundles supposed to represent a flooded-type evaporator. Experiments were carried out for a bundle of 19 tubes in triangular layout for two pitch-to-diameter ratio values – 1.7 and 2.0 – in atmospheric and sub-atmospheric pressure conditions. Average heat transfer coefficients – both local,...
-
Manoeuvring forces on azimuthing podded propulsor model
PublikacjaThis paper presents the preliminary part of comprehensive manoeuvring open- water tests of a gas carrier model. The paper focuses on open water experiments with an azimuthing podded propulsor. The test program was carried out in the cavitation tunnel and the large towing tank of Ship Hydromechanics Division, Ship Design and Research Centre, Gdańsk. The pod was tested as a pushing unit with a 161.3 mm diameter propeller. Steering...
-
Non-adiabatic Effects in Pressure Drop Calculations in Flow Boiling and Flow Condensation in Minichannels
PublikacjaConsiderations presented in the paper relate both to the case of flow boiling and flow condensation in conventional channels as well as small diameter ones. Authors devoted all the possible attention that the modeling presented is applicable to the whole range of quality variation in both cases of condensation and boiling. The form of two-phase flow multiplier, which is a major factor in modeling presented here, should be capable...
-
Late Aortic Remodeling after Endovascular Repair of Complicated Type B Aortic Dissection—TEVAR Protects Only the Covered Segment of Thoracic Aorta
PublikacjaIntroduction: TEVAR is the preferred way of treatment of complicated type B aortic dissection. The purpose of the study was to assess the impact of TEVAR on aortic remodelling in the thoracic and abdominal segment in long-term follow-up. Methods: 23 patients with complicated type B aortic dissection were treated by TEVAR in years 2004-2012 in our Department. Aortic remodelling was rated based on preoperative and final follow-up...
-
Fabrication of polyurethane and polyurethane based composite fibers by the electrospinning technique for soft tissue engineering of cardiovascular system
PublikacjaElectrospinning is the unique technique, which provides forming of polymeric scaffolds for soft tissue engineering, which include tissue scaffolds for soft tissues of cardiovascular system. Such artificial soft tissues of cardiovascular system may possess mechanical properties comparable to native vascular tissues. Electrospinning technique gives the opportu nity to form fibres with nm- to μm-scale in diameter. The arrangement...
-
Influence of bush wear in water lubricated marine stern tube bearings with shaft misalignment
PublikacjaWater lubricated propeller shaft bearings are frequently employed on modern ships due to their advantages such as durability, simplicity and low price. Specific working conditions on ships cause shaft misalignment which often results in rapid wearing of bush and shaft. Shaft misalignment could be an effect of manufacturing or assembly faults but sometimes it appears due to hull or shaft deformation. The wearing process has influence...
-
Evaluation of Sicilian landraces of broccoli (B. oleracea var. italica Plenck) for quality traits
PublikacjaBrassica oleracea L. var. italica Plenck is one of the most popular vegetables which belong to Brassicaceae family. It is getting attention as an important source of bioactive compounds such as glucosinolates, and many other phytochemicals. In the frame of the H2020 BRESOV project, we evaluated three landraces (‘Broccolo nero', ‘Ramoso calabrese' and ‘Sparaceddu') and two commercial F1 hybrid cultivars (‘Marathon' and ‘Naxos')....
-
Phytoextraction and recovery of rare earth elements using willow (Salix spp.)
PublikacjaSoil and water contaminations are caused by rare earth elements (REEs) due to mining and industrial activities, that threaten the ecosystem and human health. Therefore, phytoremediation methods need to be developed to overcome this problem. To date, little research has been conducted concerning the phytoremediation potential of Salix for REEs. In this study, two Salix species (Salix myrsinifolia and Salix schwerinii) and two Salix...
-
Assessment of image processing methods for the determination of propagation of squat-type defects in rails
PublikacjaWe demonstrate the idea of squat-type defect measurement in the rail and the concept of tracking of the defect development using the techniques of image acquisition and image processing as well as the methods of metric spaces. We introduce the concepts of a set diameter δ(A) and the metric ρ1, which come from the properties of plane figures, to compare and to observe the development of the defects. We characterize the feasibility...
-
Analysis of the macrostructure of the fuel spray atomized with marine engine injector
PublikacjaOne of the main problem influencing the combustion process in the cylinder of the marine engine is an fuel spray phenomena. The parameters describing the shape of the fuel spray are named macro parameters. This article presents the research results of the macrostructure parameters of the fuel spray atomized with the marine engine injector. The research were carried out by optical visualization measurement method of Mie scattering....
-
Experimental analysis of chip removing system in circular sawing machine
PublikacjaPaper presents analysis of the process of removing the wood chips generated during the cutting of the material on the circular sawing machine. The attention is focused on the upper cover of the chip removing system. Within the framework of the work a systematic experimental study of pressure distribution in the cover during operation of the selected rotational speed of saw blade with a diameter of 300 mm and 450 mm was carried...
-
Effect of some organic solvent - water mixtures composion on precipitated calcium carbonate in carbonation process
PublikacjaPrecipitated calcium carbonate particles were obtained during carbonation of calcium hydroxide slurry with carbon dioxide. Aqueous solutions of isopropyl alcohol, n-butanol and glycerol were used as solvents. Concentration of organic additives in the reactive mixture was from 0 to 20 % (vol.). Precipitation process were performed in a stirred tank reactor equipped with gas distributor. Multimodal courses of particles size distribution...
-
Design of a microrobotic wrist for needle laparoscopic surgery
PublikacjaThe paper addresses the design of a micro wrist for needle laparoscopic surgery (needlescopy) using MEMS technology and an original 3 degree of freedom, 3D architecture. Advancement in needlescopy drives the development of multi-dof micro-tools 1-2mmin diameter with 3D mobility but standard available fabricationtechniques are for 2.5D structures. The paper discusses thedevelopment steps and design solutions for the realization...
-
Investigations of Aerodynamics of Tesla Bladeless Microturbines
PublikacjaThe paper presents an analysis of a Tesla bladeless turbine for a co-generating micro-power plant of heat capacity 20 kW, whichoperates in an organic Rankine cycle with a low-boiling medium. Numerical calculations of flow in several Tesla turbine models areperformed for a range of design parameters. Results of investigations exhibit interesting features in the distribution of flowparameters within the turbine interdisk space. The...
-
Innovative Solutions for Immersive 3D Visualization Laboratory
PublikacjaThe paper presents results of the work concerning the technical specification of Immersive 3D Visualization Laboratory to be opened in late summer 2014 at the Faculty of Electronics, Telecommunications and Informatics at Gdańsk University of Technology in Poland. The person immersed in VR space will be placed in a transparent sphere with a diameter of over 10 feet, supported on rollers and equipped with a motion tracking system....
-
Performance of a hybrid microjet – microchannel cooling module
PublikacjaThe paper presents the experimental investigation of a microjet- microchannel cooling module. In which microjets of water are impinging into the microchannels and forming a liquid film on the impingement surface. Applied technology takes benefits from two very attractive heat removal techniques. When lminar jets are impinging on the surface have a very high kinetic energy at the stagnation point, also in microchannels boundary...