Filters
total: 3423
filtered: 2599
-
Catalog
Chosen catalog filters
displaying 1000 best results Help
Search results for: STEAM TURBINE CONTROL
-
Performance Characteristics of a Micro-turbine, International
Publication. In the paper a design of a multi-stage micro-turbine with partial admission of all the stages is described in detail and the results of particular experimental investigations and numerical calculations are shown, followed by conclusions. The co-generative micro-power plant with the HFE7100 as a working medium was designed and built for experimental investigations. The values of the main cycle parameters were as follows:- heat...
-
Drivetrain of a Wind Turbine
PublicationIn a most commonly met design of a wind turbine the power is transmitted from the rotor to the generator through the system composed of the main shaft, friction connection, multiplying gearbox and a flexible coupling. The driving system comprises almost a complete set of the machine elements being described during machine design lectures and can serve as an interesting illustration...
-
Pressure Pulsations in Turbine Blade Seal
PublicationThe paper presents the results of experimental investigations into pressure forces generated in a turbine labyrinth seal. The experiments were performed on a single-stage air model turbine of the impulse type. The performed experimental research proved that in a shroud clearance the pressure pulsates and the effects of the nozzle trailing edge thickness as well as the influence of the rotor blades are observed. The exemplary results...
-
Analysis of diagnostic informativeness of the exhaust temperature of a naval gas turbine
PublicationThe conducted investigations aimed to carry out an analysis of the possibility that the failures identification in the automatic control system of a gas turbine engine could be worked out on the basis of measurements of the exhaust stream temperature behind the gas generator. The exhaust temperature represents a basic control parameter, enabling technical state evaluation of the engine within the operation process, which is observed...
-
Modeling of entrained flow steam gasification of sewage sludge
PublicationProper management of sewage sludge becomes increasingly problematic due to legal requirements aiming at diminishing environmental impact, as well as rationalizing the utilization from the point of view of logistics. Steam gasification of sewage sludge can result in very good quality of the producer gas. So far, the works have been focused on the gasification in fixed bed gasifiers. However, this does not allow to take full advantage...
-
Corrosion of evaporator tubes in low emission steam boilers
PublicationPurpose of this paper is to reveal the mechanisms of corrosion processes of outer surfaces of low-emission steam boiler evaporator tubes. Examinations were performed to find the reasons of different corrosion susceptibility of tubes situated at combustion chamber on various levels. Examinations were conducted on several segments of 57 x 5.0 mm evaporator tubes made of 16M (16Mo3) steel grade. Segments were taken from level of...
-
Balancing energy processes in turbine engines
PublicationThe article discusses the issue of balancing energy processes in turbine engines in operation in aeronautic and PDULQHSURSXOVLRQV\VWHPVZLWKWKHDLPWRDQDO\VHDQGHYDOXDWH EDVLFRSHUDWLQJSDUDPHWHUV7KH¿UVWSDUWSUHVHQWV the problem of enormous amounts of energy needed for driving fans and compressors of the largest contemporary turbofan engines commonly used in long-distance aviation. The amounts of the transmitted power and the effect RIÀRZSDUDPHWHUVDQGFRQVWUXFWLRQDOSURSHUWLHVRIWKHHQJLQHV RQWKHLUSHUIRUPDQFHDQGUHDOHI¿FLHQF\DUH evaluated....
-
The Influence of Cooperation on the Operation of an MPC Controller Pair in a Nuclear Power Plant Turbine Generator Set
PublicationThe paper discusses the problem of cooperation between multiple model predictive control (MPC) systems. This approach aims at improving the control quality in electrical energy generation and forms the next step in a series of publications by the authors focusing on the optimization and control of electric power systems. Cooperation and cooperative object concepts in relation to a multi MPC system are defined and a cooperative control...
-
APPLICABILITY OF INLET AIR FOGGING TO MARINE GAS TURBINE
PublicationThe dependency of marine gas turbine on the ambient temperature leads to a decrease of the gas turbine power output in arid areas. Very often gas turbine power output demand is high and the power margins originally designed into the driver , has been exhausted. In such circumstances the inlet air fogging is an effective compensation of gas turbine power. In this paper an analysis of inlet air fogging applicability to marine gas...
-
ANALYSIS OF WORKING CONDITIONS OF BEARINGS NO.1 & NO.2 OF TURBINE 13K200 AND DESIGN DEVELOPMENT OF NEW BEARINGS FOR THE TURBINE AFTER RETROFITTING
PublicationThe main goal of the work consisted of preparing an analysis of working conditions of bearings No.1 and No.2 in the existing turbine 13K200, as well as designing geometries of new bearings which would allow for their proper functioning in the turbine following its retrofitting (work under higher load).
-
Design and investigations of a micro-turbine flow part
Publication-generative micro-power plant with the HFE7100 as a working medium was designed and built for experimental investigations. The heat output of the plant was assumed equal to 20 kW, while the electric output amounted to about 3kW.In the paper a multi-stage micro-turbine with partial admission of all the stages is described in detail and the results of the particular experimental investigations and numerical calculations are shown,...
-
A multistage turbine for a micro power plant
PublicationThis paper presents results of a design analysis of a multi-stage turbine for the cogeneration micro-power plant working in accordance with Organic Rankine Cycle (ORC). The heat power of the plant is assumed equal to 20 kW and the corresponding available electric output is estimated to be of about 3 kW. Different variants of the radial and axial-flow turbines have been considered, while the detailed results of the calculations...
-
Cooperative control in production and logistics
PublicationClassical applications of control engineering and information and communication technology (ICT) in production and logistics are often done in a rigid, centralized and hierarchical way. These inflexible approaches are typically not able to cope with the complexities of the manufacturing environment, such as the instabilities, uncertainties and abrupt changes caused by internal and external disturbances, or a large number and variety...
-
The selected effects of high temperature air-steam mixture wood drying
PublicationThe results of properties change of beech wood after drying process are presented. The wood taken to experiments was from northern part of Pomeranian region in Poland. Before the main high temperature drying process using air-steam mixture, wood was initially dried in an open air conditions. The high temperature drying process was conducted at temperature 120oC, humidity 48%, flow rate of drying medium 2.5m/s and atmospheric pressure....
-
Real-time hybrid model of a wind turbine with doubly fed induction generator
PublicationIn recent years renewable sources have been dominating power system. The share of wind power in energy production increases year by year, which meets the need to protect the environment. Possibility of conducting, not only computer simulation, but also laboratory studies of wind turbine operation and impact on the power system and other power devices in laboratory conditions would be very useful. This article presents a method...
-
Static Model of Steam/Water Cycle for Thermal and Economic Analysis
PublicationThe thermodynamic efficiency of typical conventional and nuclear power plants is insufficient. A large amount of the generated heat is removed to the environment and regarded as a waste. A solution which is commonly used to increase the efficiency and profitability of the existing and planned power plants refers to cogeneration of heat and power. To prepare sophisticated thermodynamic and economic analyses, a precise static model...
-
Pressure pulsations in turbine blade seal clearance
PublicationThe paper presents the results of numerical and experimental investigations into pressure forces generated in a turbine labyrinth seal. The experiments were performed on a single-stage air model turbine of the impulse type, while the numerical results were obtained by means of CFD Fluent Code. The performed experimental research and numerical calculations prove that in a shroud clearance the pressure pulsates and the effects of...
-
Novel hierarchical nonlinear control algorithm to improve dissolved oxygen control in biological WWTP
PublicationWastewater treatment is a problem known to humankind for centuries. The quality of treated sewage determines the condition of reservoirs around the world. Control of such a complex and nonlinear system as a wastewater treatment plant requires thorough knowledge of the process. The paper presents a hierarchical control system of a Sequencing Batch Reactor (SBR) in Wastewater Treatment Plant (WWTP) taking into account a model based...
-
On a Method of Efficiency Increasing in Kaplan Turbine
PublicationThis paper presents a method of increasing efficiency in Kaplan-type turbine. The method is based on blade profile optimisation together with modelling the interaction between rotor and stator blades. Loss coefficient was chosen as the optimisation criterion, which is related directly to efficiency. Global optimum was found by means of Genetic Algorithms, and Artificial Neural Networks were utilised for approximations to reduce...
-
Improvements to the STEAM-based teaching of architectural drawing
PublicationThe author of this article presents a systemic approach to improving the teaching of architectural drawing courses for engineers in the 21st Century. In this era of rapid development of digital technologies, the traditional teaching structure should be redefined to a purpose-oriented dynamic model. The existing, generally accepted teaching models have already proved successfully based on the practice-oriented STEAM programme, which...
-
An energetic analysis of a gas turbine with regenerative heating using turbine extraction at intermediate pressure - Brayton cycle advanced according to Szewalski's idea
PublicationIn this paper, a modification of a simple gas turbine into the Brayton cycle with regenerative heating, using turbine extraction at intermediate pressure, is presented. The main concept of the retrofitting is based on the transfer of heat from the turbine exhaust gases to the air entering the combustion chamber. The extracted gas transfers heat to air via the divided regenerative heat exchanger and after that is compressed and...
-
Failure of austenitic stainless steel tubes during steam generator operation
PublicationThe article presents the failure process of austenitic stainless steels used in power devices, such as heat exchangers, steam generators, in terms of local corrosion: pitting, stress and intergranular corrosion, paying particular attention to welded joints area. The effect of steel chemical composition, microstructure, welding process and work environment was analyzed. The second part of the article presents the results of the...
-
Hierarchical predictive control of integrated wastewater treatment systems
PublicationThe paper proposes an approach to designing the control structure and algorithms for optimising control of integrated wastewater treatment plant-sewer systems (IWWTS) under a full range of disturbance inputs. The optimised control of IWWTS allows for significant cost savings, fulfilling the effluent discharge limits over a long period and maintaining the system in sustainable operation. Due to the specific features of a wastewater...
-
ANALYSIS OF THE PROJECT OF INNOVATIVE FLOATING TURBINE
PublicationThe design of a floating, innovative device for river water aeration and conversion of mechanical energy to electrical energy required the analysis of a number of geometrical and dynamic features. Such an analysis may be carried out on the basis of existing methods of numerical fluid mechanics. Models of pressures, forces and torques characteristic for the conversion of watercourse energy were developed for two basic concepts of...
-
Integrated monitoring, control and security of Critical Infrastructure Systems
PublicationModern societies have reached a point where everyday life relies heavily on desired operation of critical infrastructures, in spite of accidental failures and/or deliberate attacks. The issue of desired performance operation of CIS at high security level receives considerable attention worldwide. The pioneering generic methodologies and methods are presented in the paper project for designing systems capable of achieving these...
-
Sensorless Control of Induction Machine Supplied by Current Source Inverter
PublicationThe paper describes the voltage control technique of induction machines supplied by a current source inverter. The control system is based on proposed new multi-scalar variables, which are named “r.” The control system contains the output filter capacitor's model. In the sensorless control system the Z type backstepping speed observer was applied. The mathematical dependences are confirmed by simulation and experimental research.
-
Diagnosing marine turbine engines through energy characteristics of their flow section
PublicationThe aim of the performed research was to develop of diagnostic method of the flow section of a marine turbine combustion engine based on the level of delamination of its energy characteristics. The here adopted diagnostic model provides for a formulation of the evaluation of the technical conditions based on the measurements of the parameters of the thermodynamic medium in the characteristic control cross-sections of the engine...
-
Design analysis of Tesla micro-turbine operating on a low-boiling medium
PublicationThis paper presents results of the design analysis of a Tesla bladeless turbine intended for a co-generating micro-power plantof heat capacity 20 kW, which operates in an organic Rankine cycle on a low-boiling medium. Numerical calculations of flowin several Tesla turbine models were performed for a range of design parameters. Results of investigations exhibit interestingfeatures in the distribution of flow parameters within the...
-
On the modelling of aerodynamic force coefficients for over-shroud seals of turbine stages
PublicationThis paper presents experimental investigations which made it possible to determine dynamic coefficients of labyrinth over-shroud seal of a model air turbine. The coefficients associate pressure forces with turbine rotor displacement, velocity and acceleration respective to turbine casing (linear model) and play important role in analyzing turbine-set dynamics. The obtained results indicated that involving serious errors can be...
-
Influence of high temperature air-steam mixture application on time wood drying process
PublicationThe results of influence gas-steam mixture drying process on time wood drying process are presented. Wood species, namely oak (Quercus L.), beech (Fagus L.), pine (Pinus L.) and spruce (Picea K.) from the northern part of Pomerania region in Poland, were subject of air-steam mixture drying process. Main focus of those tests was to shorten the time of drying process and afterward to check properties of wood.
-
The Method of reduction of aerodynamic forces generated in turbine blade seals
PublicationThe distibution of pressure in the seal gaps does not only affect the so called '' leakage losses'' and the turbine stage overall efficiency but also plays an important role in the generation of aerodynamic forces which may cause self-excited rotor vibrations. The paper describes a chamber seal applied for the reduction of the aerodynamic forces created in shroud seals. This kind of turbine seal was patented and tested.
-
Explanation of Reduction of Pressure Forces in Turbine Chamber Seals
PublicationThe paper describes a chamber seal reducing the aerodynamic forces created in shroud seals. Asymmetrical pressure distribution (due to rotor-stator eccentricity) in the blade tip clearance leads to the creation of pressure forces acting on the blade shroud. By increasing the volume above the shroud, the pressure distribution becomes more uniform on the whole shroud circumference and the effect of rotor eccentricity is reduced....
-
Explanation of Reduction of Pressure Forces in Turbine Chamber Seals
PublicationThe paper describes a chamber seal reducing the aerodynamic forces created in shroud seals. Asymmetrical pressure distribution (due to rotor-stator eccentricity) in the blade tip clearance leads to the creation of pressure forces acting on the blade shroud. By increasing the volume above the shroud, the pressure distribution becomes more uniform on the whole shroud circumference and the effect of rotor eccentricity is reduced....
-
An Innovative Floating System with a Savonius Rotor as a Horizontal-Axis Wind Turbine
PublicationIn this project, an innovative wind turbine was designed for a floating plant. A large Savonius rotor was replaced with a double-rotor wind turbine implemented as a horizontal-axis turbine. This double rotor was positioned on the tip of a thrust plate and fixed to the deck of a catamaran. Simple 2D numerical simulations were performed to confirm the effectiveness of the concept. An analysis of the floating system configuration...
-
Parametric Study on a Performance of a Small Counter-Rotating Wind Turbine
PublicationA small Counter-Rotating Wind Turbine (CRWT) has been proposed and its performancehas been investigated numerically. Results of a parametric study have been presented in this paper.As parameters, the axial distance between rotors and a tip speed ratio of each rotor have been selected.Performance parameters have been compared with reference to a Single Rotor Wind Turbine (SRWT).Simulations were carried out with Computational Fluids...
-
The influence of high temperature wood drying conditions using air-steam mixture on its properties
PublicationThe results of properties change of beech wood after drying process are presented. The wood taken to experiments was from northern part of Pomeranian region in Poland. Before the main high temperature drying process using air-steam mixture, wood was initially dried in an open air conditions. The high temperature drying process was conducted at temperature 120oC, humidity 48%, flow rate of drying medium 2.5m/s and atmospheric pressure....
-
Reduction of Derivative pipeline effort in water turbine
PublicationThe paper presents an approach to evaluate and reduce the effort of the derivative pipeline in a water turbine of a hydrostatic power station in its vulnerable spots. Potential places of the biggest effort of the structure, as well as the coefficient of displacement and safety factor related to them were identified using FEM numerical method. Pipeline reinforcement was designed and made based on FEM analysis. Original technology...
-
An asymmetrical λ-foot of condensing steam flow in the IMP PAN nozzle
PublicationIn the present paper we have focused on the precise prediction of the spontaneous condensation phenomena in wet steam flow. Novelty of our approach lies on modelling both the moment of initiation of a phase transition, as well as the moment of its reverse progress - called here re-vaporization of the condensate phase. The practical issue is to elaborate of a model of spontaneous condensation/vaporization of water steam flow...
-
Thermal failure of a second rotor stage in heavy duty gas turbine
PublicationThe impulse mode of operation and the supply of various types of fuels causes frequent failures even in the heavy duty gas turbines. The paper presents the ravages of second rotor stage failure in a gas turbine. The excessive thermal elongation rise caused by fuel change was indicated as the main cause. We applied nonlinear numerical analysis, preceded by thermodynamic calculations of the turbine and visual inspection of the effects...
-
The Application of Fluidic Sealing in Shrouded Gas Turbine Blades
PublicationThis paper presents a study conducted on a new gas turbine designed to limit leakage in the labyrinth seal. The slots in the fin are used to generate a bypass flow, which obstructs the flow in the gap above the fin. The method was tested numerically and experimentally beforehand using a simplified model without rotation or blade passages. In this paper, the validation of the method using a model of a turbine stage is shown. Reynolds-averaged...
-
The analysis of turbine propulsion systems in nuclear submarines
PublicationThe article systematises submarines, which are presently in service, according to their propulsion types (both conventional and nuclear), power output, and submersion depth. Contemporary types of propulsion systems installed and used in submarines are discussed. Calculations were performed for the PWR (Pressurized Water Reactor) type nuclear propulsion system and the supercritical turbine propulsion system (supercritical reactor...
-
Dynamic state assessment of the water turbine with the power of 600 kW
PublicationThe article discusses the results of experimental studies to assess the dynamic state of the turbine set with the Kaplan turbine. The dynamic assessment was made on the basis of appropriate standards, based on the measurement results of selected parameters of vibration, which have been measured for several states of the machine load. In addition, we attempted to identify the causes of the increased vibration levels based on the...
-
1D Model Callibration on the Basis on 3D calculations for Tesla Turbine
PublicationThe paper presents the system of equations for axisymmetriclaminar flow, after averaging, through the width of interdisk slit ofTesla turbine. Coefficients were introduced, as a result ofaveraging, that improve the efficiency of 1D model. The minimalnumber of such coefficients was determined. The 1D modelmakes it possible to attain analytical solutions to an accuracylimited by these coefficients. Calibration of 1D model depends...
-
Investigation of the aerodynamics of an innovative verticalaxis wind turbine
PublicationThis paper presents a preliminary three dimensional analysis of the transient aerodynamic phenomena occurring in the innovative modification of classic Savonius wind turbine. An attempt to explain the increased efficiency of the innovative design in comparison with the traditional solution is undertaken. Several vorticity measures such as enstrophy, absolute helicity and the integral of the velocity gradient tensor second invariant...
-
Damage detection in turbine wind blades by vibration based methods
PublicationThe paper describes results of numerical simulation for damage localization in the composite coat of a wind turbine blade usingmodal parameters and a modern damage detection method (wavelet transform).
-
Analysis the Parameters of the Adaptive Controller for Quality Control of Dissolved Oxygen Concentration
PublicationThe wastewater treatment plant can be considered a dynamic large scale complex system, in which the most important control parameter is the dissolved oxygen concentration in the aerobic zone. The air is supplied to this zone by the aeration system. In the paper, both the sequencing batch reactor and the aeration system are modelled and used as plant of control performed by the cascade nonlinear adaptive control system extended...
-
CO2 capture using steam ejector condenser under electro hydrodynamic actuator with non-condensable gas and cyclone separator: A numerical study
PublicationThe concept for condensation of steam and CO2 separation in a negative CO2 emission gas power plant involves the utilization of a steam ejector condenser (SEC) for direct-contact condensation of vapor with inert gas (CO2) on a spray of subcooled liquid, integrated with a separator to produce pure CO2. Due to the increasing diffusion resistance and reduced convective heat transfer between the steam and subcooled water phases...
-
Hierarchical dissolved oxygen control for activated sludge processes
PublicationA hierarchical controller for tracking the dissolved oxygen reference trajectory in activated sludge processes is proposed and investigated. The removal of nitrogen and phosphorous from wastewater is considered. Typically, an aeration system itself is a complicated hybrid nonlinear dynamical system with faster dynamics compared to the internal dynamics of the dissolved oxygen in a biological reactor. It is a common approach to...
-
Numerical investigation on the performance of a small counter-rotating wind turbine
PublicationThe article presents the results of the investigation on the performance of a small counter-rotating wind turbine. The wind turbine has been simulated using Computational Fluid Dynamics methods. Actuator Line Model has been successfully used to represent rotors in the computational domain. A parametric study has been carried out, taking into account changes in the tip speed ratio of the rotors while maintaining a constant distance...
-
Experimental Validation of Numerical Model within a Flow Configuration of the Model Kaplan Turbine
PublicationThis paper investigates validation of flow within a model Kaplan turbine. This includes comparison of various turbulence models and their influence on torque and power generated by the turbine. Numerical results were compared with experimental data.