Filters
total: 1259
filtered: 1137
displaying 1000 best results Help
Search results for: gel-fraction, physico-mechanical properties, sem
-
Morphology, Thermo-Mechanical Properties and Biodegradibility of PCL/PLA Blends Reactively Compatibilized by Different Organic Peroxides
PublicationReactive blending is a promising approach for the sustainable development of bio-based polymer blends and composites, which currently is gaining more and more attention. In this paper, biodegradable blends based on poly(ε-caprolactone) (PCL) and poly(lactic acid) (PLA) were prepared via reactive blending performed in an internal mixer. The PCL and PLA content varied in a ratio of 70/30 and 55/45. Reactive modification of PCL/PLA...
-
Influence of dispersed phase content on the mechanical properties of electroless nanocomposite Ni-P/Si3N4 and hybrid Ni-P/Si3N4/graphite layers deposited on the AW-7075 alloy.
PublicationThe article presents the results of mechanical testing of Ni-P/Si3N4 nanocomposite and hybrid Ni-P/Si3N4/graphite coatings deposited on AW-7075 aluminum alloy using the chemical reduction method. In terms of mechanical testing, microhardness was measured, and surface roughness and adhesion of the coatings to the aluminum substrate were determined using the “scratch test” method. The surface morphology of the deposited layers was...
-
Physical, Chemical and Mechanical Properties of Novel Poly(Urethaneamideimide)s
Publication -
Mechanical properties and corrosion resistance of dissimilar stainless steel welds
PublicationW artykule przedstawiono właściwości mechaniczne oraz odporność korozyjną doczołowych złączy różnoimiennych stali odpornych na korozję, austenitycznej 316L oraz duplex 2205. Blachy o grubości 15 mm spawano automatycznie łukiem krytyn z różnymi energiami liniowymi. Wykazano, że właściwości mechaniczne złączy spełniają wymagania okrętowych towarzystw klasyfikacyjnych, natomiast najbardziej narażoną strefą złącza na działanie korozji...
-
Effects of mechanical alloying conditions on the properties of Mg-based nanomaterials
Publication -
Thermal, Mechanical, and Morphological Properties of DPU/Titanate Nanotubes Nanocomposites
Publication -
The Influence of Nano-Fe3O4 on the Microstructure and Mechanical Properties of Cementitious Composites
Publication -
The Effect of Nanosilica on the Mechanical Properties of polymer-Cement Composites (PCC)
Publication -
The impact of natural fibers’ characteristics on mechanical properties of the cement composites
PublicationThe paper reviews the properties of cement composites reinforced with short fibres. The effect of natural fibres was investigated: cotton, sisal, jute, ramie, bamboo, and synthetic fibres: polymer and polypropylene. It was noticed that the fibres change the consistency of the mixture up to 15%. In the composite flexural strength tests, a change in strength by +/− 8% was observed, depending on the type of fibres used. The research...
-
Mechanical Properties of Polyester Coated Fabric Subjected to Biaxial Loading
PublicationThe paper is focused on the comparison between uniaxial and biaxial laboratory test results for polyester coated fabric. A short literature review concerning coated woven fabrics with emphasis on biaxial tensile tests is presented. A description of the polyester-coated fabric under biaxial test by means of constitutive models and material parameter values is proposed. To establish the right values of the ultimate tensile strength,...
-
Cyclic mechanical stress impact on protective properties of organic coatings
PublicationCelem pracy jest zaprezentowanie wyników badań wpływu cyklicznych naprężeń mechanicznych na układy powłoka/metal. Powtarzające się naprężenia mechaniczne zostały zidentyfikowane jako czynnik w znaczącym stopniu przyczyniający się do degradacji powłok. Próbki składające się z powłoki epoksydowej nałożonej na stal St3SAl poddano serii 21000 cykli naprężenie-odpuszczenie. Badania przeprowadzono w zakresie odkształceń elastycznych...
-
Study on Microstructure and Mechanical Properties of Laser Welded Dissimilar Joint of P91 Steel and INCOLOY 800HT Nickel Alloy
PublicationThis investigation attempts to explore the weld characteristics of a laser welded dissimilar joint of ferritic/martensitic 9Cr-1Mo-V-Nb (P91) steel and Incoloy 800HT austenitic nickel alloy. This dissimilar joint is essential in power generating nuclear and thermal plants operating at 600–650 °C. In such critical operating conditions, it is essential for a dissimilar joint to preserve its characteristics and be free from any kind...
-
Tailoring the Physico-Chemical Properties of Poly(xylitol-dicarboxylate-co-butylene dicarboxylate) Polyesters by Adjusting the Cross-Linking Time
Publication -
Evaluation of bacterial strains for developing effective plant growth promoting strain on chickpea growth and physico chemical properties of soil
PublicationThe study was intended to isolate and characterize the plant growth-promoting properties. A collection of microbial consortia called plant growth-promoting microorganisms (PGPM) work to increase crop growth and yield through a variety of direct mechanisms, including as nitrogen fixation, phosphate solubilization, synthesis of PGH, ammonia, and siderophore, as well as indirect mechanisms. The aim of the study was to evaluate the...
-
Diamond-Phase (Sp3-C) Rich Boron-Doped Carbon Nanowalls (Sp2-C): A Physico-Chemical And Electrochemical Properties
PublicationThe growth of B-CNW with different boron doping levels controlled by the [B]/[C] ratio in plasma, and the influence of boron on the obtained material’s structure, surface morphology, electrical properties and electrochemical parameters, such as -ΔE and k°, were investigated. The fabricated boron-doped carbon nanowalls exhibit activity towards ferricyanide redox couple, reaching the peak separation value of only 85 mV. The flatband...
-
P92 steel and inconel 617 alloy welds joint produced using ERNiCr-3 filler with GTAW process: Solidification mechanism, microstructure, mechanical properties and residual stresses
PublicationThe objective of the current study was to analyse the microstructure, mechanical characteristics, and residual stresses of a dissimilar welded joint (DWJ) made of P92 steel and the Inconel alloy 617 (IN617) using the gas tungsten arc welding (GTAW) method. The ERNiCr-3 filler was selected to produce the conventional V groove (VG) and narrow V groove (NVG) butt joint. The filler deficient zones in the weldments, such as the filler...
-
FTIR Study and Mechanical Properties of Cellulose Fiber-Reinforced Thermoplastic Composites
Publication -
Rigid polyurethane foams with different flame retardants and their physical and mechanical properties
PublicationRigid polyurethane foams (PUFs) containing 3, 6 or 9 % of one of of two selected fire retardants (FR): oligomeric ethyl ethylene phosphate (Fyrol PNX) and expandable graphite (EG) were prepared, inspected and compared to foam without that fillers as the control. The thermal stability of PUFs was described by horizontal test according to norm: UL 94 HB. Compressive strength and physical properties (density, fragility and water absorption)...
-
Electroconductivity and mechanical properties of carbon black Printex L6 filled polyurethanes
PublicationOpisano uzyskanie i badania kompozycji poliuretanowo-sadzowych na bazie sadzy przewodzącej Printex L6. Zaprezentowano wyniki badań nad wpływem udziału napełniacza przewodzącego na przewodnictwo elektryczne stałoprądowe i właściwości mechaniczne uzyskanych materiałów.
-
The influence of accelerated aging on selected mechanical properties of polypropylene with organic fillers
Publication -
Influence of Nanoclay on the Thermo-Mechanical Properties of Silicone Pressure-Sensitive Adhesives
Publication -
CARBOCHAIN POLYMER-GLUCOSE HYBRIDS: SYNTHESIS, THERMAL/MECHANICAL PROPERTIES AND BIODEGRADABILITY
Publication -
Effect of FSW Traverse Speed on Mechanical Properties of Copper Plate Joints
Publication -
The influence of laser alloying on the structure and mechanical properties of AlMg5Si2Mn surface layers
Publication -
Optimal Features of Porosity of Ti Alloys Considering their Bioactivity and Mechanical Properties
PublicationW artykule przedstawiono wpływ porowatości i rozmiaru porów tytanu i jego stopów, użytych, jako materiały ortopedyczne, na bioaktywność i własności mechaniczne struktur porowatych. Optymalne cechy porowatych rusztowań tytanowych umożliwiają rekonstrukcję i regenerację tkanki kostnej w zastosowaniach przenoszących obciażenie.
-
Mechanical properties cement based composites modified with nano-Fe3O4/SiO2
Publication -
Effect of Glass Powder on the Cement Hydration, Microstructure and Mechanical Properties of Mortar
Publication -
The effects of silica/titania nanocomposite on the mechanical and bactericidal properties of cement mortars
Publication -
AN ALTERNATIVE WAY OF DETERMINING MECHANICAL PROPERTIES OF WOOD BY MEASURING CUTTING FORCES
PublicationThe cutting force is an energetic effect of splitting material, and might be therefore considered from a point of view of modern fracture mechanics. The dedicated mathematical model developed for description of the wood cutting has been developed here on the base of fracture theory, and includes work of separation (fracture toughness) in addition to the material plasticity and friction. The effect of the cutting edge dullness is...
-
Gigantic electro-chemo-mechanical properties of nanostructured praseodymium doped ceria
PublicationSome oxygen defective fluorites are non-Newnham electrostrictors, i.e., the electromechanical response does not depend on their dielectric properties. Here, we show gigantic electrostriction in nanocrystalline 25 mol% praseodymium doped ceria (PCO) bulk ceramics. The material was fabricated with a fieldassisted spark plasma sintering (SPS) process from high-purity nanoscale PCO powders (<20 nm). The SPS process consolidates the...
-
Cold recycled mixtures for binder courses - laboratory evaluation of mechanical properties
PublicationCold recycled mixtures composed with cement and bituminous emulsion are nowadays commonly used material for base layer. Typical pavement with cold recycled mixtures usually consists of two asphalt courses (wearing and binding course) constructed over cold recycled base. Therefore the next step in cold recycling is possibility of design of binding courses with recycled materials, but with potential to obtain high quality mixtures...
-
Biological and mechanical properties of bone cement with nanoparticles - in vivo and in vitro research
PublicationDespite antibiotics preventive treatment, before and after an implant implementation, risk of infection are real. These infections at the implant surface develop in a few months after applying them into the body. To prevent the development of bacteria and to reduce the risk of infection, implants coated with nanoparticles come into use. The Mechanical Department of the Technical University of Gdańsk carried out a research with...
-
Biological and mechanical properties of bone cement with nanoarticles - in vitro and in vivo research
PublicationDespite antibiotic preventive treatment both before and after implant implementation, the risks of infection are real. These infections develop at the implant surface a few months after inserting them into the body. To prevent the development of bacteria and reduce the risk of infection, implants coated with nanoparticles are used. The Mechanical Department of the Technical University of Gdansk carries out research into using bone...
-
Mechanical Properties of Single-Walled Carbon Nanotubes with AIREBO Force-Filed
Publication -
Effect of starch fillers on the dynamic mechanical properties of rubber biocomposite materials
PublicationIn the paper the results of dynamic mechanical study of the biocomposites containing one of two types of (potato or corn) strach used as fillers in different amount were discussed. The composites were obtained from rubbery mixture containing natural rubber (NR) as a main component. Thermomechanical analyses (by DMA) showed that the used quantity of strach fillers only slightly influence on the glass transition temperature of vulcanizates.
-
Influence of deformation velocity on mechanical properties of high strength structural steels.
PublicationW referacie przedstawiono wyniki badań własności mechanicznych stali wysokiej wytrzymałości przeznaczonych na spawane konstrukcje okrętowe w zależności od prędkości odkształcenia. Badania były prowadzone w Akademii Marynarki Wojennej oraz w Politechnice Gdańskiej przy współudziale Uniwersytetu Technicznego w Rostocku podczas opracowywania charakterystyk tych stali dla potrzeb polskiego przemysłu okrętowego. Uwzględnienie obciążeń...
-
Modelling of mechanical properties of cooper alloys sand cast ship propellers.
PublicationBadania właściwości mechanicznych (Rm ,A5) stopów miedzi, stosowanych na pędniki okrętowe, w zależności od ich składu chemicznego i grubości odlewów piaskowych pozwalają na wyznaczenie równań regresji mających zastosowanie do prognozowania wytrzymałości statycznej na rozciąganie (Rm) i wydłużenia plastycznego (A5).Obliczenia wartości Rm i A5 dla wybranych odlewów piaskowych (mosiądz MM55, brązy BA93, BA2 i CMA1) wykazały, że opracowane...
-
Tailoring of structural and magnetic properties of nanosized lithium ferrites synthesized by sol–gel self-combustion method
Publication -
Cobalt doping of nickel ferrites via sol gel approach: effect of doping on the structural and dielectric properties
Publication -
Enhanced Mechanical and Electromechanical Properties of Compositionally Complex Zirconia Zr1–x(Gd1/5Pr1/5Nd1/5Sm1/5Y1/5)xO2−δ Ceramics
PublicationCompositionally complex oxides (CCOs) or high-entropy oxides (HEOs) are new multi-element oxides with unexplored physical and functional properties. In this work, we report fluorite structure derived compositionally complex zirconia with composition Zr1- x(Gd1/5Pr1/5Nd1/5Sm1/5Y1/5)xO2-δ (x = 0.1 and 0.2) synthesized in solid-state reaction route and sintered via hot pressing at 1350 °C. We explore the evolution of these oxides'...
-
Fish gelatin-nanoclay films. Part I: Effect of a kind of nanoclays and glycerol concentration on mechanical and water barrier properties of nanocomposites
PublicationThe aim of work was the improvement of the mechanical and water barrier properties of nanocomposites prepared from fish gelatin and nanoclays (5–15%), plasticized with glycerol at different concentrations. The effect of hydrophilic Cloisite Na1 and Nanomer®PGV was compared with that exerted by organically modified more hydrophobic Nanofil®2 and NanoBent ZR-1. Antimicrobial activity of nanocomposites containing hydrophobic nanoclays...
-
A dissimilar welded joint of grade 92 steel and AISI 304L steel obtained using IN82 buttering and IN617 fller: relationship of microstructure and mechanical properties
PublicationUnfavourable operating conditions of equipment in the energy industry resulting from high-temperature loads determine the need to use special materials and technological solutions, including welding procedures. In this article, buttering using IN82 (ERNiCr-3) consumables was proposed as a method to improve the weldability of grade 92 steel joined by the gas tungsten arc welding (GTAW) process with AISI 304L (IN617 fller). The...
-
How to Improve Physico-Chemical Properties of Silk Fibroin Materials for Biomedical Applications?—Blending and Cross-Linking of Silk Fibroin—A Review
Publication -
Effect of protein-xanthophylls (PX) concentrate of alfalfa supplementation on physico-chemical properties of turkey breast and thigh muscles during ageing
Publication -
Effect of molar ratio [NCO]/[OH] groups during prepolymer chains extending step on the morphology and selected mechanical properties of final bio‐based thermoplastic poly(ether‐urethane) materials
PublicationThe main aim of this work was to investigate the effect of [NCO]/[OH] molar ratio used during the prepolymer chain extending step (with bio‐based diols) on the chemical structure, and thermomechanical and mechanical properties of thermoplastic poly(ether‐urethane)s. Thermoplastic poly(ether‐urethane)s were obtained from bio‐based polyol (polytrimethylene ether glycol), bio‐based glycol (1,4‐butanediol or 1,3‐propanediol), and 4,4'diphenylmethane...
-
Recycling of Industrial Waste as Soil Binding Additives—Effects on Soil Mechanical and Hydraulic Properties during Its Stabilisation before Road Construction
PublicationTo improve the in situ soil stabilization, different chemical additives are used (ion exchange compounds, additives based on H2SO4 or vinyl polymers, and organic additives using lignosul- fonates). One interesting alternative is the production of additives from various waste materials. The extensive testing of waste-based blends with soil was performed; the mechanical (unconfined compressive strength (UCS)) and hydraulic (capillary...
-
Superconducting properties of an NbN-SiO2 disordered system obtained by ammonolysis of NbN-SiO2 sol-gel derived coatings
PublicationW pracy przedstawiono wyniki badań właściwości nadprzewodzących warstw NbN-SiO2. Warstwy uzyskano poprzez azotowanie w temperaturze 1200C otrzymanych metodą zol-żel warstw Nb2O5-SiO2, o różnym stosunku molowym Nb2O5/SiO2. Badania rezystywne przeprowadzono w zakresie temperatur 5-280K. Przeprowadzono również badania absorpcji mikrofal (MMMA). Właściwości nadprzewodzące otrzymanych próbek silnie zależą od grubości warstw jak również...
-
SU-GG-T-267: Imaging Properties of the OCTOPUSTM-IQ Scanner in Combination with a New Polymer Gel Dosimeter
Publication -
Surface properties and visible light activity of W-TiO2 photocatalysts prepared by surface impregnation and sol-gel method
PublicationTiO2 modyfikowany wolframem otrzymano dwiema metodami: metodą zol-żel oraz metodą impregnacji powierzchniowej. Fotokatalizatory kalcynowano w temperaturze 400C. Jako matrycę TiO2 zastosowano ST-01 (Ishihara Sangyo, Japonia, 300m2/g). jako prekursory wolframu zastosowano tlenek wolframu oraz heksakarbonylek wolframu. Badania obejmowały wpływ ilości domieszki na aktywność fotokatalityczną. Charakterystyka otrzymanych fotokatalizatorów...
-
Influence of W Addition on Microstructure and Mechanical Properties of Al-12%Si Alloys
Publication