Search
displaying 1000 best results Help
Search results for: HYDROSTATIC THRUST BEARING, FRICTION LOSSES, HYDRODYNAMIC THRUST BEARING, HYDROSTATIC POCKET SIZE
-
Hydrodynamic pressure in micro-and nano bearing gap
Publication.
-
New Generation of Water lubricated Foil bearing - Numerical Models and Experimental Verification
PublicationIn the paper a new idea of foil water lubricated bearing and methodology of hydrodynamic characteristics calculations is presented. To assesses the theoretical characteristics of these bearings two different computer models were built. First is structural model coupled with fluid model. It takes into account: fluid flow in the deformed fluid gap, specific design of bearing support and friction in bearing support. The second is...
-
The Concept of Geodetic Analyses of the Measurement Results Obtained by Hydrostatic Leveling
PublicationThe article discusses the issue of hydrostatic leveling. Its application is presented in structural health monitoring systems in order to determine vertical displacements of controlled points. Moreover, the article includes a complete computation scheme that utilizes the estimation from observation differences, allowing the elimination of the influence of individual sensors’ systematic errors. The authors suggest two concepts of...
-
Investigation of the thrust generated by active isolated hydrofoils via wave-induced ship motion
PublicationWave Augmented Hydrofoil Technology (WAHT) aims to convert hydrofoil movement, induced by ship motion, into thrust force, and ship's resistance reduction in waves. Despite the growing interest in WAHT, a significant research gap remains in understanding the complex interactions between hydrofoil design parameters and wave-induced thrust generation. A hydrofoil attached to a ship serves dual roles; reducing the ship resistance in...
-
Effect of water contamination of an environmentally acceptable lubricant based on synthetic esters on the wear and hydrodynamic properties of stern tube bearing
PublicationThe ecological aspects of the lubrication of stern tube bearings on ships represent a critical challenge today. Oil leakages are a typical issue, even for new systems, similarly to water ingress from the environment. One of the options for improving environmental protection is replacing mineral oil with an environmentally adaptable lubricant (EAL). This paper reports experimental investigations of the effect of water content in...
-
Determination of vertical displacements by using the hydrostatic levelling systems with the variable location of the reference sensor,
PublicationAbstract: In this paper, the author proposed a new method for determination of vertical displacements with the use of hydrostatic levelling systems. The traditional method of hydrostatic levelling uses a rule in which a position of reference sensor is stable. This assumption was not adapted in the proposed method. Regarding the issue mentioned above, the reference sensor is treated in the same way as the others sensors that measure...
-
Instantaneous power signal measurements for bearing diagnostics
Open Research DataBearing diagnostics can be carried out based on the method, which relies on the measurement and analysis of the variability of the signal instantaneous power, defined as the product of instantaneous current and voltage power supplied to the engines. Bearing damage causes the appearance of deformations, which are in the form of additional harmonic components...
-
Hydrodynamic journal bearing - ''Y'' particularly for steam turbines.
PublicationW artykule przedstawiono koncepcję i zasadę działania nowego, ślizgoweo łożyska poprzecznego typu ''Y''. Przedstawiono wady i zalety nowego rozwiązania. Porównano charakterystyki dynamiczne i statyczne klasycznego łożyska cytrynowego (soczewkowego) z nowym łożyskiem ''Y''.Podano przykładowe wdrożenia i ich efekty.
-
Theoretical and mathematical models of the torque of mechanical losses in a hydraulic rotational motor for hydrostatic drive
PublicationW pracy przedstawiono modele teoretyczne i matematyczne momentu strat mechanicznych występujących w silniku hydraulicznym obrotowym o stałej teoretycznej chłonności qMt silnika na obrót wału (o stałej teoretycznej objętości roboczej VMt silnika) i o zmiennej chłonności qMgv = bM qMt na obrót wału (o zmiennej geometrycznej objętości roboczej VMgv silnika). Modele mają służyć badaniom laboratoryjnym i symulacyjnym strat energetycznych...
-
The Concept of Accuracy Analysis of the Vertical Displacements Gained from the Hydrostatic Levelling Systems’ Measurements
PublicationAbstract: Nowadays, hydrostatic levelling is a widely used method for the vertical displacements’ determinations of objects such as bridges, viaducts, wharfs, tunnels, high buildings, historical buildings, special engineering objects (e.g., synchrotron), sports and entertainment halls. The measurements’ sensors implemented in the hydrostatic levelling systems (HLSs) consist of the reference sensor (RS) and sensors located on the...
-
Design of a Shape-Memory-Alloy-Based Carangiform Robotic Fishtail with Improved Forward Thrust
PublicationShape memory alloys (SMAs) have become the most common choice for the development of mini- and micro-type soft bio-inspired robots due to their high power-to-weight ratio, ability to be installed and operated in limited space, silent and vibration-free operation, biocompatibility, and corrosion resistance properties. Moreover, SMA spring-type actuators are used for developing different continuum robots, exhibiting high degrees...
-
DYNAMIC POSITIONING CAPABILITY ASSESSMENT BASED ON OPTIMAL THRUST ALLOCATION
PublicationThe article presents an efficient method of optimal thrust allocation over the actuators in a dynamically positioned ship, according to the DNV-ST-0111 standard, Level 1. The optimisation task is approximated to a convex problem with linear constraints and mathematically formulated as quadratic programming. The case study is being used to illustrate the use of the proposed approach in assessing the DP capability of a rescue ship....
-
Mineral oil-based hydrostatic drives as the basic drive systems in the construction of offshore eqiupment projects
PublicationThe aim of this article is to present the components used in the production of mineral oil-based hydrostatic drives as the basic drive systems for the offshore industry. The article contains de-scriptions of the components of the said systems, with the description of their suitability for mi-neral oil operation and offshore applications.
-
Acoustic journal bearing - A search for adequate configuration
PublicationClassical non-contact bearings are already used in a number of specialist applications but there are somespecialist areas where they cannot be used for variety of reasons and acoustic sliding bearings could be an alternative. The paper presents the quest for a configuration of an acoustic journal bearing and shows that the overall shape of the bearing and its geometry are of a vital importance for the load capacity oft he bearing....
-
Experimental research on marine oil-lubricated stern tube bearing
PublicationBearings of propeller shafts are very crucial elements of the propulsion system of each of the ships. The safety of shipping depends on their durability and reliability. The new legal restrictions mean that today we are looking for environmentally friendly solutions. That is why water-lubricated bearings are becoming more and more popular. So, will oil-lubricated shaft bearings belong to the past? The bearing with a white metal...
-
Energy losses in the hydraulic rotational motor - definitions and relations for evaluation of the efficiency of motor and hydrostatic drive
PublicationStosowane dotychczas w badaniach naukowych i w praktyce przemysłowej metody oceny strat i sprawności energetycznej obrotowych silników hydraulicznych stosowanych w napędach hydrostatycznych dają błędne rezultaty, ponieważ obarczone są wpływem samych strat na parametry, w funkcji których straty i sprawności są oceniane.Celem pracy było zdefiniowanie w silniku parametrów pracy, rozwijanych mocy, występujących strat i sprawności energetycznej...
-
Bearing capacity of the working platform with kinematic method
PublicationBearing capacity of the working platform for heavy tracks was analysed using Distinct Layout Optimization (DLO) method. The platform layer constructed from cohesionless soils is resting on weak cohesive subgrade. Different thickness of the platform, its effective angle of internal friction and undrained shear strength of the soft soil were taken into consideration. Kinematic method permits different failure mechanisms to be analyzed....
-
Environmentally acceptable lubricants (EAL) compared with a reference mineral oil as marine stern tube bearing lubricant – Experimental and theoretical investigations
PublicationThe purpose of this research is to indicate the potential differences in bearing characteristics resulting from the application of different lubricant types with the same viscosity grade. The effect of different environmentally acceptable lubricants (EALs) on hydrodynamic journal bearing properties is studied experimentally and compared to the properties obtained after lubrication with a reference mineral oil. The results of the...
-
Power efficient thrust allocation algorithms in design of dynamically positioned ships
PublicationAssessment of power consumption on a Dynamically Positioned (DP) ship in the early design stage can assist crucial design choices. The study presents a comparison between two algorithms of optimal thrust allocation in a propulsion system for an over-actuated DP ship. Applied algorithms were Quadratic Programming (QP) and Non- dominated Sorting Genetic Algorithm II (NSGAII). Based on both approaches, tools were developed for ship...
-
Dimple measurements in bronze 80 mm textured sliding bearing
Open Research DataRaw measuring data for complete measurements of 3 dimples from 3D geometrical measurements were performed on textured bushing (with ball shaped dimples on the inner bearing face). Custom built measuring device for measurements.
-
Biocompatibility and bioactivity of bearing loaded metallic implants
PublicationPresentation of developed titanium alloy base composite materials possessing better biocompatibility, longer lifetime and bioactivity behavior for bearing loaded implants, e.g. hip joint and knee joint endoproshtesis.
-
INFLUENCE OF TIME ON THE BEARING CAPACITY OF PRECAST PILES
PublicationOne of the most popular types of foundations in layered subsoil with very differentiated soil shear strengths are precast piles. One of the reasons is a fact that we can well control the driving process during the installation of these piles. The principles of the assessment of bearing capacity and settlements of the piles given by Eurocode 7, concentrate on two main methods, i.e. Static Pile Load Tests (SPLT) and Dynamic Driving...
-
Diagnosis of bearing damage in induction motors by instantaneous power analysis
PublicationResearch of the machine with simulated bearing damages has been carried out, where variable load torque, simulating bearing damage, was introduced. The results show that components which can be used for bearings diagnosis appear in the spectrum of the product of current and supply voltage instantaneous values. These components are easier to identify than the components of current spectrum, which have been used so far in diagnostic...
-
Running performance of an aerodynamic journal bearing with squeeze film effect
PublicationResults of theoretical and experimental studies concerning the performance of an aerodynamic journal bearing of which running is assisted by squeeze film ultrasonic levitation (SFUL) are presented in this paper. The SFUL mechanism not only can separate journal from the bearing at the start and stop phases of operation but also can significantly contribute to the dynamic stability of the bearing when it runs at speed. Computer calculations...
-
Some problems of slide bearing material fatigue evaluation.
PublicationA slide bearing alloy resistance against fatigue failures have been investigated for three different lubricants, different heat loadings and different stress ratio κ values. The research methods and data handling procedures for determination of particular parameter effects on fatigue strength have been described and analysed for experiments that were set and performed in laboratory tester SKMR-2. Main and interaction effects of...
-
Bearing capacity of working platform using distinct layout optimization method
PublicationBearing capacity of the working platforms from sandy soil resting on NC and OC clays was analyzed using LimitState GEO program. Different failure modes are considered using distinct layout optimization (DLO) method, which forms the upper bound solution of limit state analysis. Different mechanisms of failure were observed as a function of the platform thickness, angle of internal friction of the platform material and undrained...
-
Evaluation of the Variability of Vibration Measurement Results in Rolling Bearing Quality Control
PublicationThe final result of rolling bearing quality control is influenced by many factors that are not always taken into account. If non-conforming products leave the factory, then the reliability of equipment containing rolling bearings is significantly weakened. The paper presents an analysis of the reasons for the variability of vibration measurement results in rolling bearing quality control. The paper describes the organisation of...
-
Problems of analytical determination of journal bearing bush fatigue strength estimates
PublicationProblems connected with determination of stress distribution in sliding layer of thinwalled bearing bushes, investigated in bearing fatigue test rigs, have been presented. Using an example of plain bearings tested in the fatigue machine SMOK (built at the Gdask University of Technology) problems with obtaining a convergence of iterative procedure for determining the fatigue strength estimators of bearing alloy surface layer are...
-
ANALYSIS OF THE POSSIBILITIES OF HIGH SPEED SHAFT BEARING SYSTEM DURABILITY INCREASE
PublicationDuring the operation of wind turbines with a gearbox of traditional configuration, a high failure rate of high-speed shaft bearings is observed. Such a high failures frequency is not reflected in standard bearing durability calculation methods, which can be attributed to atypical failure mechanism. To avoid observed problems in the 1.5 MW wind turbine, the modification of the existing bearing system is proposed. Multiple options,...
-
Effect of the working liquid compressibility on the picture of volumetric and mechanical losses in a high pressure displacement pump used in a hydrostatic drive Part II Mechanical losses in a pump
PublicationŚciśliwość cieczy roboczej może znacząco zmienić wartości i proporcje współczynników strat objętościowych i mechanicznych w pompie wyporowej zastosowanej w układzie napędu hydrostatycznego. Wpływ ten jest szczególnie widoczny w trakcie pracy pod wysokim ciśnieniem a także wówczas, gdy występuje zapowietrzenie cieczy roboczej. W części II przedstawiono model matematyczny momentu strat mechanicznych w pompie oraz jego laboratoryjną...
-
Biocompatibility and Bioactivity of Load-Bearing Metallic Implants
PublicationThe main objective of here presented research is to develop the titanium (Ti) alloy base composite materials possessing better biocompatibility, longer lifetime and bioactivity behaviour for load-bearing implants, e.g. hip joint and knee joint endoprosthesis. The development of such materials is performed through: modeling the material behaviour in biological environment in long time and developing of new procedures for such evaluation;...
-
Displacement piles - classification and methods for the calculation of bearing capacity.
PublicationDisplacement piles belong to a group of technologies whose main idea is to install or make a pile without extracting ground material. According to definition, contained in PN-EN:1997-1:2008, displacement piles should be considered as driven, pressed in using vibrators and made with the use of spread augers. The classification of piles used so far with regard to the technology of execution is modified. An additional element is the...
-
Effect of the working liquid compressibility on the picture of volumetric and mechanical losses in a high pressure displacement pump used in a hydrostatic drive. Part I Energy losses in a drive system, volumetric losses in a pump
PublicationŚciśliwość cieczy roboczej może znacząco zmienić wartości i proporcje współczynników strat objętościowych i mechanicznych w pompie wyporowej zastosowanej w układzie napędu hydrostatycznego. Wpływ ten jest szczególnie widoczny w trakcie pracy pod wysokim ciśnieniem a także wówczas, gdy występuje zapowietrzenie cieczy roboczej. W części I przedstawiono wykres zaproponowany przez autora, wzrostu mocy w układzie napędu hydrostatycznego...
-
Effect of the working liquid compressibility on the picture of volumetric and mechanical losses in a high pressure displacement pump used in a hydrostatic drive. Part I Energy losses in a drive system, volumetric losses in a pump
PublicationŚciśliwość cieczy roboczej może znacząco zmienić wartości i proporcje współczynników strat objętościowych i mechanicznych w pompie wyporowej zastosowanej w układzie napędu hydrostatycznego. Wpływ ten jest szczególnie widoczny w trakcie pracy pod wysokim ciśnieniem a także wówczas, gdy występuje zapowietrzenie cieczy roboczej. W części I przedstawiono wykres zaproponowany przez autora, wzrostu mocy w układzie napędu hydrostatycznego...
-
Extended duration running and impulse loading characteristics of an acoustic bearing with enhanced geometry
PublicationThis paper presents performance during prolonged running of the acoustic bearing when PZTs are switched off and when they are switched on. The effect of active PZT on shaft’s displacements in X and Y directions is clearly demonstrated. Performance of the acoustic bearing was also assessed when an impulse force was applied to the running shaft at speed. Once again the benefits of having PZTs active are beyond doubt. The instability...
-
Analysis of Failures of High Speed Shaft Bearing System in a Wind Turbine
PublicationDuring the operation of wind turbines with gearbox of traditional configuration, consisting of one planetary stage and two helical stages high failure rate of high speed shaft bearings is observed. Such a high failures frequency is not reflected in the results of standard calculations of bearing durability. Most probably it can be attributed to atypical failure mechanism. The authors studied problems in 1.5 MW wind turbines of...
-
THE SYNCHROSQUEEZING METHOD IN BEARING ESTIMATION OF STATIONARY SIGNALS FOR PASSIVE SONAR WITH TOWED ARRAY
PublicationIn this paper, a novel method of bearing estimation in a passive sonar system with a towed array is introduced. The classical approach of bearing estimation based on the spatial spectrum [1] is extended by using the synchrosqeezing method that is a part of the reassignment method introduced by Kodera et al. [2]. Using this method leads to a precise bearing estimation. The proposed method requires a relatively small amount of computation,...
-
Motor bearing diagnostics performed by means of laser vibrometer
PublicationDamage of bearings is the most common cause of failures in squirrel-cage induction motors. That is why the issues connected with diagnostics of bearings are so important. The equipment employed for bearing diagnostics usually makes use of vibrations as the criterion for technical condition of the bearings. This paper presents exemplary results of the research conducted on bearings with artificially introduced damage. A scanning...
-
Use of Neural Networks in Diagnostics of Rolling-Element Bearing of the Induction Motor
PublicationBearing defect is statistically the most frequent cause of an induction motor fault. The research described in the paper utilized the phenomenon of the current change in the induction motor with bearing defect. Methods based on the analysis of the supplying current are particularly useful when it is impossible to install diagnostic devices directly on the motor. The presented method of rolling-element bearing diagnostics used indirect...
-
Mathemathical model of radial passive magnetic bearing
PublicationIn the article mathematical radial model of passive magnetic bearings to ocean engineering units has been presented. The units application in underwater thrusters should increase propulsion systems durability and gives lower maintenance costs. The rotor of electric motor is hanging in magnetic field taken from radial passive magnetic bearings. However axial direction maintenance must be controlled with electromagnets and their...
-
Search for the most useful geometry of an acoustic journal bearing
PublicationComputer simulations of a number of journal bearing’s geometries utilising acoustic levitation were carried out. The choice of the best geometry depended on the ability of a deformed shape, created by piezo-electric elements, to facilitate squeeze film ultrasonic levitation, and also to create three evenly distributed diverging aerodynamic gaps. Deformations of analysed variants of the bearing’s shape were generated by numerical...
-
Acoustic journal bearing – Performance under various load and speed conditions speed conditions
PublicationThe paper presents results of experimental testing aiming at finding out what effect system of piezo-electric actuators (PZTs)attached to an aerodynamic journal bearing has on the magnitude of shaft's motion within the bearing operating at specified speed and load. The results clearly demonstrate effectiveness of PZTs in mitigating the shaft's motion thus contributing to the increased stability of the bearing. This stabilizing...
-
Water-lubricated stern tube bearing - experimental and theoretical investigations of thermal effects
PublicationThe paper presents research results of thermal phenomena accompanying operation of a water-lubricated stern tube bearing with axial grooves. Experimental tests revealed, that intensity of forced axial flow has strong influence on bush temperature. Numerical simulations focused on investigation of the thermal phenomena under operation of water-lubricated journal bearing showed, that restricted axial flow promotes backflow of the...
-
Energy Loss Coefficients ki in a Displacement Pump and Hydraulic Motor used in Hydrostatic Drives
PublicationThe article aims at defining and analysing the energy loss coefficients in design solutions of rotating displacement machines, with a piston machine as an example. The energy losses observed in these machines include mechanical loss, volumetric loss, and pressure loss. The scale and relations between these losses in different machines depend on machine design and manufacturing quality, and on operating parameters. The operating...
-
Improving the accuracy of bearing in active sonar with cylindrical array using spectrum estimation.
PublicationThe articles presents a method for improving the accuracy of bearing in multibeam sonar with a cylindrical array. Based on a known spatial spectrum estimation technique, the method has been successfully used in linear array systems. Its accuracy of bearing is satisfactory and ensures a relatively low computational effort. The article discusses certain simplifications and assumptions to adapt the spatial spectrum estimation technique...
-
Temperature measurements in monitoring of large thrust bearings
PublicationW pracy przedstwiono krytyczną analizę aktualnych metod diagnostyki dużych hydrodnamicznych łożysk wzdłużnych hydrozespołów elektrowni wodnych. Wykazano niedostatki i zagrożenia płynące ze stosowania diagnostyki opartej na jednopunktowym pomiarze temperatury. Zaprezentowano wstępna koncepcję nowej metody diagnostycznej opartej na odwrotnym zagadnieniu przepływu ciepła (IPHC).
-
Temperature measurements in monitoring of large thrust bearings
PublicationW pracy przedstwiono krytyczną analizę aktualnych metod diagnostyki dużych hydrodnamicznych łożysk wzdłużnych hydrozespołów elektrowni wodnych. Wykazano niedostatki i zagrożenia płynące ze stosowania diagnostyki opartej na jednopunktowym pomiarze temperatury. Zaprezentowano wstępna koncepcję nowej metody diagnostycznej opartej na odwrotnym zagadnieniu przepływu ciepła.
-
Temperature Measurements in Monitoring of Large Thrust Bearings
PublicationW pracy przedstawiono krytyczną ocenę popularnego systemu diagnostyki dużych łożysk wzdłużnych (np. łożysk nośnych hydrogeneratorów), w którym stosowany jest jednopunktowy pomiar temperatury w klockach łożyskowych. Stwierdzono, że taki układ pomiarowy nie pozwala na bezpieczną eksploatację łożysk, ponieważ posiada bardzo duże opóźnienie czasowe, nie daje informacji o lokalnych zagrożeniach, nie pozwala racjonalnie ustalić poziomów...
-
Influence of local bush wear on water lubricated sliding bearing load carrying capacity
PublicationOne of main problems concerning water-lubricated bearings is their durability. There are known cases of bearings with life time measured in decades, and some, whose refurbishment was necessary just days after start-up. Obtaining stable fluid film friction plays key role in the durability of these bearings. Unfortunately, their load-carrying capacity is limited due to water's low-viscosity. The conducted experimental...
-
Analysis of sloping brace stiffness influence on stability and load bearing capacity of a truss
PublicationThe paper is focused on the numerical study of stability and load bearing capacity of a truss with side elastic braces. The structure is made in reality. The rotational and sliding brace stiffnesses were taken into account. Linear buckling analysis and non-linear static analysis with geometric and material nonlinearity were performed for the beam and shell model of the truss with respect to the angle of sloping braces. As a result...