Search
Search results for: 304L AUSTENITIC STAINLESS STEEL
-
Influence of microstructure on properties of 18Cr-10Ni-Ti stainless steel products.
PublicationBadano wpływ mikrostruktury na właściwości mechaniczne i odporność korozyjną wyrobów ze stali austenitycznej 18Cr-10Ni-Ti po przesycaniu z temperatury 1050 C. Wykazano, że węgliki TiC w ziarnach i na granicach ziaren/bliźniaków powodują znaczne obniżenie wydłużenia stali. Węgliki TiC na granicach ziaren/bliźniaków obniżają odporność na korozję międzykrystaliczną i sprzyjają powstawaniu uszkodzeń korozyjnych podczas hutniczej operacji...
-
The influence of the welding thermal cycles on corrosion resistance of duplex stainless steel
PublicationBadano skłonnośc strefy wpływu ciepła spoin ze stali dupleks do korozyjnego pękania narężeniowego. Wykonano próby korozyjne z wykorzystaniem metody SSRT w środowisku korozyjnym wrzącego MgCl2. Wykazano, że duży udział ferrytu w strukturze SWC pogarsza odpornośc na korozję. Badania metalograficzne na mikroskopie lektronowym wykazały różne sposoby propagacji pęknięcia zależnie od zawartości austenitu w strukturze SWC.
-
Investigation of pitting corrosion of stainless steel by means of acousticemission and potentiodynamic methods.
PublicationPrzedstawiono wyniki badań korozji wżerowej przy jednoczesnym wykorzystaniu techniki potencjodynamicznej i emisji akustycznej. Dystrybuanta rozkładu prawdopodobieństwa wystąpienia korozji wżerowej (CDFp) została uzyskana na podstawie badań potencjodynamicznych. Niezależnie z wyników akustycznych otrzymano dystrybuantę rozkładu zdarzeń akustycznych (CDFae). Na podstawie wyników stwierdzono brak korelacji miedzy wynikami potencjodynamicznymi...
-
Deis assessment of intergranular corrosion process proceeding on AISI 304 stainless steel
PublicationW pracy przedstawiono nowe podejście do badania mechanizmu i intensywności korozji międzykrystalicznej. Badania przeprowadzono przy wykorzystaniu techniki dynamicznej elektrochemicznej spektroskopii impedancyjnej (DEIS), która pozwala na jednoczesne rejestrowanie chwilowych zmian impedancji oraz prądu stałego badanego układu. Tym samym możliwe jest otrzymanie z jednego pomiaru informacji dotyczących zarówno mechanizmu korozji międzykrystalicznej,...
-
Investigation of pitting corrosion of stainless steel by means of acoustic emission and potentiodynamic methods
Publication -
Impedance investigation of passive 304 stainless steel in the pit pre-initiation state
PublicationZaprezentowano wyniki badań impedancyjnych stali stopowej 304L metodą klasycznej EIS i dynamicznej EIS. Badania związane były z przejściem stali stopowej ze stanu pasywnego do inicjacji powstawania wżerów. Na podstawie zmian parametrów elektrycznego schematu zastępczego stwierdzono, że najbardziej prawdopodobnym mechanizmem tworzenia się wżerów jest model zniszczenia (pęknięcia) warstwy pasywnej.
-
Influence of spatial structures of 316L stainless steel on its cavitation erosion resistance
Publication -
Hydrogen assisted cracking of 2205 duplex stainless steel in synthetic sea water
PublicationThe cracking behavior of 2205 duplex stainless steels (DSSs) in synthetic sea water under cathodic polarization condition was investigated. (SSRT) method was employed in aim to evaluate the susceptibility to hydrogen assisted cracking. The results showed that the reduction in the uniform elongation (UEL) and the reduction of area (RA) varied with the applied cathodic current density. Significant reductions in ductility were found,...
-
Cost-effective methods of fabricating thin rare-earth element layers on SOC interconnects based on low-chromium ferritic stainless steel and exposed to air, humidified air or humidified hydrogen atmospheres
PublicationMost oxidation studies involving interconnects are conducted in air under isothermal conditions, but during real-life solid oxide cell (SOC) operation, cells are also exposed a mixture of hydrogen and water vapor. For this study, an Fe–16Cr low-chromium ferritic stainless steel was coated with different reactive element oxides – Gd2O3, CeO2, Ce0.9Y0.1O2 – using an array of methods: dip coating, electrodeposition and spray pyrolysis....
-
Sintering Parameter Investigation for Bimetallic Stainless Steel 316L/Inconel 718 Composite Printed by Dual-Nozzle Fused Deposition Modeling
PublicationFused deposition modeling (FDM) nowadays offers promising future applications for fabricating not only thermoplastic-based polymers but also composite PLA/Metal alloy materials, this capability bridges the need for metallic components in complex manufacturing processes. The research is to explore the manufacturability of multi-metal parts by printing green bodies of PLA/multi-metal objects, carrying these objects to the debinding...
-
Dry cutting effect in turning of a duplex stainless steel as a key factor in clean production
Publication -
Investigations on surface induced tribological characteristics in MQCL assisted machining of duplex stainless steel
Publication -
DEIS assessment of AISI 304 stainless steel dissolution process in conditions of intergranular corrosion
Publication -
Stainless steel/yttria stabilized zirconia composite supported solid oxide fuel cell
PublicationW tym artykule opisano wytworzenie i przebadanie kompozytowych elementów nośnych tlenkowych ogniw paliwowych. Podłoża nośne zostały wytworzone ze stali nierdzewnej i tlenkiem itru stabilizowanego tlenku cyrkonu (YSZ), których proszki zmieszano w różnych proporcjach objętościowych. Zachowanie podłoży podczas spiekania (skurcz liniowy, porowatość) oraz wysokotemperaturowe właściwości (odporność na utlenianie, przewodność elektryczna)...
-
Instantaneous impedance evaluation of dissolution of aisi 304 stainless steel during intergranular corrosion
PublicationCelem pracy było uzyskanie informacji dotyczących zróżnicowania parametrów elektrycznych uzyskanych na podstawie zarejestrowanych chwilowych widm impedancyjnych w zakresie aktywacji i reaktywacji roztwarzania wysokostopowej stali austenitycznej AISI podczas postępującego procesu korozji międzykrystalicznej. Badania prowadzono z wykorzystaniem dynamicznej elektrochemicznej spektroskopii impedancyjnej (DEIS). Pomiary wykonywano ''on-line''...
-
Cavitation erosion behavior of 18/8 stainless steel after its laser alloying of manganese
PublicationW pracy przedstawiono badania kawitacyjne stali austenitycznej 18/8 po laserowym stopowaniu jej powierzchni różną zawartością manganu. Oceniano podatnoś stopowanej powierzchni do odkształceniowego umacniania pod wpływem obciążeń kawitacyjnych oraz głębokość umocnienia.
-
Cavitation erosion behavior of 18/8 stainless steel after its laser alloying of manganese
PublicationW pracy przedstawiono wyniki badań własności kawitacyjnych stali nierdzewnej gatunku 18/8 po jej laserowym stopowaniu różną zawartością manganu. Stwierdzono, że przy zawartości Mn w ilości 7,13% występuje największy wzrost twardości po stopowaniu a głębokość umacniania na skutek działania obciążeń kawitacyjnych jest najmniejsza.
-
Evaluation of porous ferritic Fe22Cr stainless steel for solid oxide fuel cells at high temperature
PublicationW pracy przedstawiono wyniki badań korozji stali Fe22Cr w wysokich temperaturach.
-
Surface Layer Properties of Sintered Ferritic Stainless Steel Remelted and Alloyed with FeNi and Ni by HPDL Laser
Publication -
Laser Thermal Oxidation by Ytterbium-Doped Fibre Laser of the Hot and Cold-Rolled Stainless Steel Surface
Publication -
Corrosion studies using potentiodynamic and EIS electrochemical techniques of welded lean duplex stainless steel UNS S82441
Publication -
The influence of plasma-sprayed coatings on surface properties and corrosion resistance of 316L stainless steel for possible implant application
Publication -
Corrosion Resistance and Mechanical Properties of TIG and A-TIG Welded Joints of Lean Duplex Stainless Steel S82441 / 1.4662
Publication -
On the Possibility of Improving the Oxidation Resistance of High-Chromium Ferritic Stainless Steel Using Reactive Element Oxide Nanoparticles
PublicationHigh-chromium ferritic steels are current the only viable candidates for cheap interconnect materials for application in high-temperature solid oxide fuel and electrolyzer cells (HT-SOFCs/SOECs). The durability and operating characteristics of interconnects manufactured using these materials may be improved significantly by applying a protective-conducting MoCo2O4 coating and depositing an intermediate layer consisting of nanoparticles...
-
DEIS evaluation of the relative effective surface area of AISI 304 stainless steel dissolution process in conditions of intergranulatar corrosion
PublicationWyniki przedstawione w tej pracy stanowią dalszą część badań dotyczących procesu roztwarzania wysokostopowej stali AISI 304 w warunkach zachodzenia korozji międzykrystalicznej z wykorzystaniem techniki dynamicznej elektrochemicznej spektroskopii impedancyjnej (DEIS). Po raz pierwszy zaprezentowano zmiany względnej powierzchni efektywnej procesu roztwarzania stali AISI 304 w warunkach zachodzenia korozji międzykrystalicznej w funkcji...
-
Impact of sensitization on dissolution process of AISI 304 stainless steel during intergranular corrosion evaluated using DES technique
Publication -
DEIS evaluation of the relative effective surface area of AISI 304 stainless steel dissolution process in conditions of intergranular corrosion
Publication -
Impact of sensitization on dissolution process of AISI 304 stainless steel during intergranular corrosion evaluated using DEIS technique
Publication -
Pool boiling heat transfer of water-Al2O3 and water-Cu nanofluids on horizontal stainless steel smooth and rough tubes
PublicationPrzedstawiono wyniki badań eksperymentalnych przejmowania ciepła przy wrzeniu nanocieczy woda-Al2O3 i woda-Cu na poziomych rurkach ze stali nierdzewnej. Ustalono, że niezależnie od badanej koncentracji nanocząstek (0.01%, 0.1% oraz 1%) współczynnik przejmowania ciepła dla nanocieczy był wyższy niż dla wody i rósł ze wzrostem koncentracji. Ponadto współczynnik przejmowania ciepła dla nanocieczy wzrastał ze wzrostem ciśnienia.
-
The effect of pressure on heat transfer during pool boiling of water-Al2O3 and water-Cu nanofluids on stainless steel smooth tubes
PublicationPrzedstawiono wyniki badań eksperymentalnych wrzenia nanocieczy woda-Al2O3 i woda-Cu o koncentracjach nanocząstek 0.01%, 0.1% oraz 1% przy ciśnieniu absolutnym 10 kPa, 100 kPa oraz 200k Pa.
-
The effect of pressure on heat transfer during pool boiling of water-Al2O3 and water-Cu nanofluids on stainless steel smooth tube
PublicationPrzedstawiono wyniki badań eksperymentalnych wrzenia nanocieczy woda-Al2O3 i woda-Cu o koncentracjach nanocząstek 0.01%, 0.1% oraz 1% przy ciśnieniu absolutnym 10 kPa, 100 kPa oraz 200k Pa.
-
High temperature corrosion evaluation and lifetime prediction of porous Fe22Cr stainless steel in air in temperature range 700–900 °C
PublicationThis work describes a high temperature corrosion kinetics study of ~30% porous Fe22Cr alloys. The surface area of the alloy (~0.02 m2 g-1) has been determined by tomographic microscopy. The weight gain of the alloys was studied by isothermal thermogravimetry in the air for 100 hours at 700 - 900 °C. Breakaway oxidation was observed after oxidation at 850 °C (~100 hours) and 900 °C (~30 hours). The lifetime prediction shows the...
-
Atomic force microscopy based approach to local impedance measurements of grain interiors and grain boundaries of sensitized AISI 304 stainless steel
Publication -
A Study on Bead on Plate (BOP) Test for Laser Welding Application of Stainless Steel to Liquified Hydrogen Tank (PART I: STS 304)
Publication -
Measurement file of stainless stell shaft LSS1 and LSS2 with diameter 95,995 with 3d measurment device
Open Research Data3d point cloud consist of measured points on new stainless steel shaft used during testing hydrodynamic journal PEEK bearing.
-
Corrosion Study of Ceria Protective Layer Deposited by Spray Pyrolysis on Steel Interconnects
PublicationSingle fuel cells and electrolysis cells are assembled into stacks using interconnects in order to increase power and gas production capacity. The most common choice for the interconnect material is stainless steel. It has good electrical and mechanical properties and is also cost effective. One of the problems when using steel is the formation of a thermally grown oxide scale during use which has a lower electrical conductivity...
-
Effect of annealing temperature on slurry erosion resistance of ferritic X10CrAlSi18 steel
PublicationIn the present work, the slurry erosion tests were carried out to investigate the influence of heat treatment on slurry erosion process of ferritic X10CrAlSi18 stainless steel using a slurry pot test rig. X10CrAlSi18 stainless steel was tested in as-received condition and after annealing at three different temperatures: 600°C, 800°C and 1000°C. Degradation of materials due to slurry erosion depends on many factors connected with...
-
Report no: WOiO /II/46/2015 - Construction node verification test, estimation of breaking load (shear force) and destruction form
PublicationA new generation of tanks for LNG transportation has been designed. Mass reduction forced our customer to use three different materials: austenitic steel, aluminium alloy and LNG compressed wood between them. The expertise concerns structural node between tank foundation and suspension. Expertise contains: description of object of test, test principals, results and conclusions
-
Development of Microstructured Carbon Coatings by Substrate-Catalytic CVD
PublicationCarbon nanostructured films were synthesized by chemical vapor deposition (CVD) on H18 stainless steel (AISI 440C) sheets with an H2/CH4/N2 gas mixture at various substrate temperatures. During the synthesis, the iron and chromium oxide layer was formed between the steel and carbonaceous layer. The carbon films exhibited wall-like and spherical morphologies and structures, as characterized by scanning electron microscopy and Raman...
-
Load capacity of steel-aluminium brackets under static and cyclic laboratory tests
PublicationThe aim of the research is the laboratory investigation of steel-aluminium brackets employed to fasten lightweight curtain walls to building facilities. Static pressure, suction forces, and cyclic loads parallel to end plates (horizontal – to simulate wind influence) were applied in the study. The steel-aluminium brackets were tested on a reinforced concrete substrate made of C30/37 concrete class to simulate the real working conditions....
-
The AFM micrographs of pitting corrosion evolution on high-alloy steel 1.4301
Open Research DataThe dataset contains the results of topographic imaging of high-alloy stainless steel 1.4301 on which the pitting corrosion process was induced by electrochemical methods. The study of the effects of a local attack allows for conclusions about the intensity and mechanism of this type of corrosion. The file contains atomic force microscopy (AFM) data...
-
INFLUENCE OF TACK WELDS DISTRIBUTION AND WELDING SEQUENCE ON THE ANGULAR DISTORTION OF TIG WELDED JOINT
PublicationIn this paper the influence of tack welds distribution and welding sequence on angular distortion of the Tungsten Inert Gas (TIG) welded joint was tested. Additionally, the effect of welding current on angular distortion was assessed. For research X2CrTiNb18 (AISI 441) stainless steel (2.5 mm thick) was chosen. During research specimens were prepared with different distributionsof tack...
-
Dissimilar autogenous TIG joint of Alloy 617 and AISI 304H steel for AUSC application
PublicationTo reduce costs and improve high-temperature performance in Advanced Ultra Super Critical (AUSC) boilers, it is necessary to weld austenitic steel to Inconel alloy. In this study, the autogenous tungsten inert gas (TIG) welding process was used to join Alloy 617 and an austenitic AISI 304H steel plate of thickness 5 mm. Microstructural analysis showed that the microstructure formation was uneven along the weldments, with columnar...
-
Burnout Investigation of Small Diameter Tubes Immersed in Nanofluids
PublicationThis paper deals with research into pool boiling critical heat flux (CHF) of water–Al2O3, water–TiO2 and water–Cu nanofluids on horizontal stainless steel tubes. The experiments were conducted under atmospheric pressure. Nanoparticles were tested at concentrations of 0.001%, 0.01%, 0.1% and 1% by weight. Ultrasonic vibration was used in order to stabilize the dispersion of the nanoparticles. Although dispersants were not used to...
-
Bending test results of first metatarsophalangeal joint after arthrodesis with medially or dorsally positioned locking plate and lag screw.
Open Research DataThe Dataset contains the results of the bending test of first metatarsophalangeal (MTP1) joint specimens after arthrodesis.
-
Influence of nanoparticle concentration on convective heat transfer of water-Al2O3 nanofluids inside horizontal tubes
PublicationThis work presents preliminary results of the experimental investigation of the forced convection heat transfer of water-Al2O3 nanofluids inside stainless steel tube with 8 mm internal diameter and 2000 mm length. Nanoparticles were tested at the concentrations of 0.01%, 0.1%, 1% and 5% by weight and the Reynolds number range encompasses laminar as well as turbulent flows.
-
Analisys of the failure of fixator used in bone surgery
PublicationThe Gamma nail (fixator) made of stainless steel, which has broken in the body, was subjected to examination. The fixator was removed from the patient femur. The fracture occurred in the area of the nail hole after two months' stay in the organism. The research included chemical composition, hardness of the Gamma nail material and the observation and analysis of the type of fracture. The research showed the fatigue failure of the...
-
Wear of Ultra-thin DLC or Tungsten-modified DLC Coatings under Reciprocating Sliding
PublicationIn the paper results are presented from tests in reciprocating sliding of self mated specimens of DLC and tungsten modified DLC coatings on stainless steel substrate. The contact geometry chosen for the research task was ball on flat. The contacts were lubricated either with distilled water or medical saline solution. Results are presented with regard to wear resistance as a function of material type and lubricant used.
-
Evaluation of cathode materials for electrochemical photocatalyst deposition
PublicationElectrochemical deposition of photocatalyst, especially TiO2, onto several cathode materials was investigated and evaluated. The deposited films were characterized by scanning electron microscopy (SEM), energy dispersive X-ray spectrometer (EDX) and electrochemical measurements. Photocatalytic activity was determined by the decomposition of cyclohexane in air by irradiation with ultraviolet light emitting diodes. It was found that...
-
SiC coating in ring-on-ring sliding with saline solution (0.9%) lubrication 5MPa, 0.1m/s specimn. #B37/#A35
Open Research DataWear tests in sliding friction of SiC coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, SiC over SiC . Mean contact stress: 5MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: SALINE SOLUTION (0.9%). Tribometer: PT-3. Overall test time till coating penetration 3 min.Secimen...