Search results for: PROPELLER SHAFT BEARINGS
-
The use of plate springs for preloading of a system of tapered roller bearings of a wind turbine gearbox
PublicationThe use of preloaded tapered roller bearings in wind turbine drive systems allows a transfer of load in the case of high variations of axial forces. The examined bearing system, a modification of a current design, consists of a pair of different sized bearings. Previous study showed the high sensitivity of tapered roller bearings on the existing radial interference. Dimensional tolerances used in the original design do not allow...
-
Tribological model of porous bearings with particular attention given to the lubricant lubricity
PublicationThe friction and wear problems, accompanying all the tribological systems, lead to reduced service life. In order to prevent such situation, it is necessary to maintain fluid friction, which improves durability of all friction nodes in a tribological system. In the paper, the tribological system consists of porous bearings and the model deals with their weakest spots - the oil outflow points in the porous wall. A kinetic model...
-
Measurement file of stainless stell shaft LSS1 and LSS2 with diameter 95,995 with 3d measurment device
Open Research Data3d point cloud consist of measured points on new stainless steel shaft used during testing hydrodynamic journal PEEK bearing.
-
Shaking table experimental study on the effectiveness of polymer bearings for seismic isolation of structures
PublicationSeismic isolation has been recognised to be a very effective way of protecting structures from damage during earthquakes. It allows us to extend the natural period of the structure and therefore avoid resonance with the ground motion. Moreover, by increasing damping in the isolation devices, more energy can be dissipated and thus the structural response can be further reduced. The aim of this paper is to show the results of the...
-
Novel condition monitoring of induction motor bearings via motor current signature analysis
PublicationThe paper authors are researching the assessment of bearing conditions in induction motors. The methods developed by the authors are based on measurements and analysis of the motor supply current, which is particularly attractive in the absence of access to the engine. The article provides an overview of selected methods of induction motor bearings diagnostic based on Motor Current Signature Analysis (MCSA). However, there is no...
-
POSSIBILITY OF ASSESSMENT OF OPERATION OF SLIDING BEARINGS IN PISTON-CRANK MECHANISMS OF DIESEL ENGINES WITH REGARD TO LOAD AND TIME OF CORRECT WORK OF THE BEARINGS BY APPLYING ACOUSTIC EMISSION AS A DIAGNOSTIC SIGNAL
PublicationAbstract: The paper presents a possibility of determining (assessing) operation of sliding bearings with multilayer bushings in crank-piston mechanisms of diesel engines. Properties of load and wear, particularly fatigue and abrasive, are characterized in general. Acoustic emission as a diagnostic signal was proved to be useful for detection of the wear of sliding and barrier layers. Results of measurements of acoustic emission...
-
ENERGY ANALYSIS OF THE PROPULSION SHAFT FATIGUE PROCESS IN A ROTATING MECHANICAL SYSTEM PART III DIMENSIONAL ANALYSIS
PublicationThis article presents the third and last part of the problem of diagnosing the fatigue of marine propulsion shafts in terms of energy with the use of the action function, undertaken by the authors. Even the most perfect physical models of real objects, observed under laboratory conditions and developed based on the results of their research, cannot be useful in diagnostics without properly transferring the obtained results to the...
-
Numerical and Experimental Study of Propeller Ventilation
Publication -
Numerical and Experimental Study of Propeller Ventilation
Publication -
Hydroacustic activity of the ship propeller operation
PublicationPraca przedstawia działanie śrub okretowych jako źródła sygnałów hydroakustycznych, związanych przede wszystkim z różnymi formami kawitacji występującymi podczas pracy śrub.
-
Polymeric Bearings as a new base isolation system suitable for mitigating machine-induced vibrations
PublicationThe present paper summarizes the preliminary results of the experimental shaking table investigation conducted in order to verify the effectiveness of a new base isolation system consisting of Polymeric Bearings in reducing strong horizontal machine-induced vibrations. Polymeric Bearing considered in the present study is a prototype base isolation system, which was constructed with the use of a specially prepared flexible polymer...
-
Numerical estimation of the pile toe and shaft unit resistances during the installation process in sands
PublicationNumerical simulations of a pile jacking were carried out. A Coupled Eulerian–Lagrangian (CEL) formulation was used to treat with large deformation problems. An Abaqus, a commercial Finite Element Method software suit, was used as a computing environment. The Mohr–Coulomb constitutive model was applied and the Coulomb model of friction was used to describe pile-soil interaction. Calculations were made for three different pile diameters....
-
Experimental study on the feasibility of alternative materials for tilting pad thrust bearings operating in transition to mixed friction
PublicationIn hydrodynamic bearings traditional bearing alloys: Babbitts and bronzes are most frequently utilized. Polymer sliding layers are sometimes applied as a valuable alternative. Hard diamond-like carbon (DLC) coatings, which are also considered for certain applications may show some advantages, as well. Although material selection is of secondary importance in a full film lubrication regime it becomes important in mixed friction...
-
Problems of Flaking in Strengthening Shaft Burnishing
PublicationThe article presents the results of testing the surface condition of shafts manufactured by a strengthening rolling burnishing process. The shafts with a hardness about 220 HB were burnished with a roller with different force. Researches were carried out with particular attention to the structure of the outflowing material in the tool zone during burnishing process. The article presents the results of the examinations of burnished...
-
Prediction of Pile Shaft Capacity in Tension Based on Some Direct CPT Methods—Vistula Marshland Test Site
PublicationThis paper presents different CPT methodologies for the prediction of the pile shaft resistance in tension on the example of three reference screw piles of the Jazowa test site in Poland. The shaft capacity was estimated based on the cone resistance, sleeve friction and CPT excess pore water pressure. Three piles with diameter 0.4 m and the length varied from 8 m to 14.6 m were subjected to static load tests in tension. Their...
-
On the Possibilities of Decreasing Power Loss in Large Tilting Pad Thrust Bearings
PublicationJournal Menu About this Journal Abstracting and Indexing Aims and Scope Article Processing Charges Articles in Press Author Guidelines Bibliographic Information Citations to this Journal Contact Information Editorial Board Editorial Workflow Free eTOC Alerts Publication Ethics Submit a Manuscript Table of Contents Abstract Full-Text PDF Full-Text HTML...
-
Prediction of pile shaft capacity in tension based on some direct CPT methods – Vistula Marshland test site
PublicationThis paper presents different CPT methodologies for the prediction of the pile shaft resistance in tension on the example of three reference screw piles of the Jazowa test site in Poland. The shaft capacity was estimated based on the cone resistance, sleeve friction and CPT excess pore water pressure. Three piles with a diameter of 0.4 m and the length...
-
Application of acoustic emission for detection of fatigue microdemage in main and crank bearings for diesel engines
PublicationThe article presents reasons for applying the acoustic emission (AE) to detect fatigue microdamage in main bearings and crank bearings of ship main engines. Problem of determination of the fatigue life for slide bearing bushes was characterized in general. There were demonstrated properties of the objects of research, which were bushings made of the MB58 alloy, as well as an overall description of the research. It was shown that...
-
Sliding bearings with sintered bronze bush lubricated by contaminated water with solid particles – Theoretical and experimental studies
PublicationSliding journal bearings lubricated with water coming directly from the environment are a solution used in shipbuilding, pumps and hydropower. However, the working fluid or surrounding water cannot always be filtered because of design limitations, which often causes the problem of premature wear of these sensitive bearings. The research conducted made it possible to assess the wear of sliding bearings lubricated with water containing...
-
POSSIBILITY OF IDENTIFICATION OF TECHNICAL CONDITION OF BEARINGS FOR SELF-IGNITION ENGINES BY APPLICATION OF ACOUSTIC EMISSION AS A DIAGNOSTIC SIGNAL
PublicationThis paper presents the results of empirical studies where the acoustic emission (AE) method was applied to identify the technical condition of sliding surfaces of main and crank bearings for main diesel engines. The test results indicate that the measurements of the AE parameters allow the technical condition identification for bearings of this type. The results refer to the measurements of the parameters for AE generated in the...
-
The dynamic performance analysis of the Micro-turbine's rotor supparted on slide and roling element bearings
PublicationThis article presents the results of investigations of dynamic characteristics of a small-dimension rotor with slide and rolling element bearings. The object of investigations was the rotor-bearing system designed for the ORC based low-power steam micro-turbine. The investigations were performed using MESWIR series programs, as well as commercial FEA software ABAQUS and MADYN 2000. The results of modal analysis of the micro-rotor...
-
The Experimental Determination of Bearings Dynamic Coefficients in a Wide Range of Rotational Speeds, Taking into Account the Resonance and Hydrodynamic Instability
PublicationMethods for the experimental determination of dynamic coefficients are commonly used for the analysis of various types of bearings, including hydrodynamic, aerodynamic and foil bearings. There are currently several algorithms that allow estimating bearing dynamic coefficients. Such algorithms usually use various excitation techniques applied to rotor–bearings systems. So far only a small number of scientific publications show how...
-
A decision-making system supporting selection of commanded outputs for a ship's propulsion system with a controllable pitch propeller
PublicationThe ship's operators have to make decisions regarding the values of commanded outputs (commanded engine speed and pitch ratio) which ensure maximum vessel speed and minimum fuel consumption. Obviously, the presented decision problems are opposed. Therefore, there is a need for a compromise solution that enables more flexible vessel voyage planning. This paper deals with development of a computer-aided system supporting selection...
-
Some fundamental aspects of self-levitating sliding contact bearings and their practical implementations
PublicationIn this study, fundamental aspects and mechanisms of acoustic levitation together with governing equations are presented first. Then, the acoustic levitation phenomenon is considered as a new way to design air suspension systems capable of self-levitation. A particular emphasis is laid on journal bearings and their specific geometrical configuration. A practical feasibility of using acoustic levitation to separate contacting surfaces...
-
Comparison of the characteristics of journal bearings determined according to ISO 7902:2020 and obtained by other methods
PublicationThe article presents selected characteristics of journal bearings calculated with the use of various methods and compared to the results obtained with application of the basic bearing characteristics calculation procedure, as described in the ISO 7902:2020 standard. Additionally, the presented calculation results were compared with the parameters measured during experimental tests of the sliding bearings, working under loads and...
-
Supply current signal and artificial neural networks in the induction motor bearings diagnostics
PublicationThis paper contains research results of the diagnostics of induction motor bearings based on measurement of the supply current with usage of artificial neural networks. Bearing failure amount is greater than 40% of all engine failures, which makes their damage-free operation crucial. Tests were performed on motors with intentionally made bearings defects. Chapter 2 introduces the concept of artificial neural networks. It presents...
-
Ducted and Open Propeller Subjected to Intermittent Ventilation
Publication -
The Analysis of Overall Ship Fuel Consumption in Acceleration Manoeuvre using Hull-Propeller-Engine Interaction Principles and Governor Features
PublicationThe problem of reduction of greenhouse gas emissions in shipping is currently addressed by many research works and related industries. There are many existing and visionary technologies and ideas, which are conceptually defined or practically realised. This goal can be achieved in different ways, and reducing fuel consumption is one of the major methods. In these circumstances, the aim of this study is to analyse the possibility...
-
Behaviour of Asymmetric Structure with Base Isolation Made of Polymeric Bearings
PublicationEarthquake-induced ground motions are the most severe and unpredictable threats to the structures all around the world. Seismic excitations cause a lot of damage in a wide variety of ways, leaving thousands of casualties in their wake. Due to randomness of earthquake occurrence, lack of visible causes and their power of destructiveness, structural engineers need to develop new technical solutions and protection systems against...
-
Advanced Hysteretic Model of a Prototype Seismic Isolation System Made of Polymeric Bearings
PublicationThe present paper reports the results of acomprehensive study designed to verify the effectiveness of an advanced mathematical model in simulating the complex mechanical behaviour of a prototype seismic isolation system made of polymeric bearings (PBs). Firstly, in order to construct the seismic bearings considered in this research, a specially prepared flexible polymeric material with increased damping properties was employed....
-
Induction Motor Bearings Diagnostic Using MCSA and Normalized Tripple Covariance
PublicationDiagnosis of induction motors, conducted remotely by measuring and analyzing the supply current is attractive with the lack of access to the engine. So far there is no solution, based on analysis of current, the credibility of which allow use in industry. Statistics of IM bearing failures of induction motors indicate, that they constitute more than 40% of IM damage, therefore bearing diagnosis is so important. The article provides...
-
Is it possible to predict performance of large thrust bearings on the basis of the results of experiments on smaller bearings?
PublicationTreścią referatu jest analiza możliwości przeniesienia wyników badań modelowych z małych hydrodynamicznych łożysk wzdłużnych do określenia własności łożysk o dużych rozmiarach. Posłużono się analizą wymiarową do określenia wymaganych współczynników skali, których zachowanie podczas badania łożyska modelowego, zapewnia jego podobieństwo do łożyska o dużych rozmiarach. Uzyskane wyniki poddano dyskusji.
-
Effectiveness of a mathematical model in simulating nonlinear mechanical behaviour of a seismic isolation system made of polymeric bearings
PublicationThe present study was focused on determining the effectives of a nonlinear mathematical model in simulating complex mechanical behaviour of a seismic isolation system made of Polymeric Bearings. The proposed mathematical model defines the lateral force as a nonlinear function of the shear displacement and the deformation velocity. The effectiveness of the proposed mathematical model was verified by comparing the seismic response...
-
Evaluation of apparent Young׳s modulus of the composite polymer layers used as sliding surfaces in hydrodynamic thrust bearings
PublicationHydrodynamic bearings with a polymer sliding layer are able to operate in severe conditions, mainly due to favorable properties of the polymers. The goal of this research was to evaluate apparent Young׳s modulus of two types of the polymer composite layers used for sliding surfaces in hydrodynamic bearings, as a function of temperature. The Young׳s modulus was evaluated on the basis of compression tests carried out on samples obtained...
-
Behaviour of asymmetric structures with base isolation made of Polymeric Bearings
PublicationEarthquake-induced ground motions are the most severe and unpredictable threats to the structures all around the world. Seismic excitations cause a lot of damage in a wide variety of ways, leaving thousands of casualties in their wake. During the last few years alone, the world has witnessed many major earthquakes, five of which have caused far-reaching consequences of a national scale for Haiti (January 2010), Chile (February...
-
Ring thruster with magnetic bearings
Publication.
-
MCSA with Normalized Triple Covariance as a bearings diagnostic indicator in an induction motor
PublicationStatistics of bearing failures in induction motors indicate, that they constitute more than 40% of IM damage, therefore bearing diagnosis is very important. Vibration methods for bearing diagnostics have one major disadvantage - they require the availability of the machine for sensors installation. This is the reason for seeking new methods based on motor supply current analysis. Diagnosis of induction motors, conducted remotely...
-
Reduction of vibrations of steel structure models with Polymeric Bearings - experimental study
PublicationEarthquake-induced ground motions are the most severe and unpredictable threats to the structures all around the world. Therefore, designing earthquake protective systems has become an extremely challenging problem in civil engineering. Base isolation is one of the most popular and widely adopted methods of protecting structures against earthquake forces. The present paper reports the results obtained from the shaking table experimental...
-
Ion recognition properties of new pyridine-2,6-dicarboxamide bearing propeller-like pendant residues: multi-spectroscopic approach
PublicationThe synthesis and ion binding properties of new amide derived from propeller-like tris(2-pyridyl)amine and 2,6-pyridinedicarboxylic acid chloride were described. Amide binds divalent metal cations: copper(II), nickel(II), zinc(II), and lead(II) in acetonitrile. In acetonitrile:water mixture (9:1 v/v) amide interacts only with copper(II) and nickel(II) cations forming complexes of 1:1 stoichiometry. It was found that the introduction...
-
Current based Normalized Triple Covariance as a bearings diagnostic feature in induction motor
PublicationDiagnosis of induction motors, conducted remotely by measuring and analyzing the supply current is attractive with the lack of access to the engine. So far there is no solution, based on analysis of current, the credibility of which allow use in industry. Statistics of IM bearing failures of induction motors indicate, that they constitute more than 40% of IM damage, therefore bearing diagnosis is so important. The article provides...
-
Mutual hydrodynamic interaction between the operating propeller and the rudder
PublicationPraca przedstawia opis algorytmu i programu do analizy oddziaływania hydrodynamicznego pomiędzy pracującą śrubą a sterem. Algorytm jest oparty na jednoczesnym rozwiązaniu zadania brzegowego dla śruby i steru. Wyniki obliczeń obejmują rozkłady ciśnienia i zmienne siły hydrodynamiczne na śrubie i sterze oraz niestacjonarne zjawiska kawitacyne na obu obiektach. Wyniki obliczeń porównano z rezultatami badań eksperymentalnych.
-
Dynamic interaction of the cavitating propeller tip vortex with the rudder
PublicationPraca przedstawia model teoretyczny i obliczeniowy dynamicznego oddziaływania kawitującego wiru wierzchołkowego śruby okrętowej z płetwą sterową. W wyniku oddziaływania zmienia się geometria wiru, powodując generowanie wysokich pulsacji ciśnienia w otaczającej wodzie i na kadłubie okrętu. Wyniki obliczeń skonfrontowano z rezultatami pomiarów laboratoryjnych na modelach. Pokazano praktyczną przydatność modelu obliczeniowego do projektowania...
-
Scale effects in cavitation experiments with marine propeller models
PublicationPraca zawiera przegląd specyficznych efektów skali występujących w badaniach kawitacyjnych modeli śrub okrętowych oraz analizę ich wpływu na prognozowane osiągi śrub okrętowych w skali rzeczywistej.
-
Sawing accuracy on the twin shaft multi-rip saw
PublicationW pracy przedstawiono analizę i wyniki badań doświadczalnych dokładności przecinania na dwuwrzecionowej pilarce tarczowej. Zaprezentowano warianty struktury geometryczno-ruchowej dwuwrzecionowej pilarki tarczowej, jak również warunki pracy dolnych górnych pił pilarki.
-
Analysis of ship shaft line coupling bolts failure
PublicationW artykule przedstawiono dane statystyczne dotyczące uszkodzeń linii wałów okrętowych, w tym także pęknięć zmęczeniowych śrub sprzęgieł kołnierzowych wałów. Wyjaśniono także mechanizm powstawania tego typu uszkodzeń i zagrożenia jakie niosą ze sobą. Opisano przypadki takich uszkodzeń oraz badania jakie są prowadzone dla lepszego poznania zjawisk zmęczeniowych w omawianych uszkodzeniach.
-
TWO-SHAFT GAS TURBINE TEACHING AND TESTING STATION
PublicationThe station was established as part of a project co-financed by the European Union with the funds of the European Regional Development Fund as part of the Infrastructure and Environment Operational Programme titled: “Establishment of state-of-the-art technical infrastructure for the Engineers of the Future learning programme at the Gdańsk University of Technology” executed in 2013-2015.
-
Induction motor bearings diagnostic indicators based on MCSA and normalized triple covariance
PublicationInduction motors are one of the most widely used electrical machines. Statistics of bearing failures of induction motors indicate, that they constitute more than 40% of induction motor damage. Therefore, bearing diagnosis is so important for trouble-free work of induction motors. The most common methods of bearing diagnosis are based on vibration signal analysis. The main disadvantage of those methods is the need for physical access...
-
The use of Acoustic Emission to identification damages bearings the main and crank engines about the automatic ignition
PublicationThe article describes the laboratory tests, which make the first stage of the study concerning the use of the AE method to determine the technical state of the slide bearings in engines with self-ignition. The aim of the present tests was to compare the recorded signals in relation to the technical state of the material of the bearing bush and to check the possibility of using the AE method in determining the transition moment...
-
Theoretical analysis and experimental tests of tilting pad journal bearings with shoes made of polymer material and low-boiling liquid lubrication
PublicationSelecting the appropriate bearing system for the rotor requires a good knowledge of the available solutions and the operating conditions of the machine. For newly designed machinery operating in adverse conditions, selecting bearings that ensure correct and long-lasting operation can be extremely challenging. Difficulties in- crease when the machine’s operating parameters are beyond the technical capabilities of available technical solutions....
-
Fatigue investigation of plain journal bearings
PublicationW artykule przedstawiono wybrane wyniki badań nad wytrzymałością zmęczeniową warstw ślizgowych w panwiach łozysk poprzecznych, prowadzonych w laboratorium tribologicznym Katedry Konstrukcji i Eksploatacji Maszyn Politechniki Gdańskiej. Opisano stanowiska badawcze i metodykę planowania eksperymentów oraz procedurę opracowywania wyników testów zmęczeniowych. Przedstawiono zamierzenia badawcze w zakresie przedmiotowych badań zmęczeniowych.